Search

During the operation of multi-electric aircraft, the polytetrafluoroethylene (PTFE) material used to insulate the aviation cable is subjected to a high electric field while working under the extreme conditions of high temperatures for a long time, which can easily cause a partial discharge and even flashover along the surface, which seriously threaten the safe operation of the aircraft. In this paper, the electrical insulation properties of PTFE were regulated via modification by the magnetron sputtering of TiO2 under high temperatures, and modified PTFE with different sputtering times was prepared. The direct current (DC) surface discharge, surface flashover, and electric aging characteristics of modified PTFE were studied under the condition of 20~200 °C, and the mechanisms by which modification by sputtering of TiO2 and high temperature influence the insulation properties were analyzed. The results show that the surface discharge intensity increases with the increase in temperature, the modification by sputtering of TiO2 can significantly inhibit the partial discharge of PTFE, and the flashover voltage first increases and then decreases with the increase in the modification time. The modification by magnetron sputtering can effectively increase the surface potential decay rate of the PTFE, increase the shallow trap energy density, effectively avoid charge accumulation, inhibit the partial discharge phenomenon, and improve the surface electrical insulation and anti-aging properties. [ABSTRACT FROM AUTHOR]

Repairing load-bearing bone defects in children remains a big clinical challenge. Mineralized collagen (MC) can effectively simulate natural bone composition and hierarchical structure and has a good biocompatibility and bone conductivity. Polylactic acid (PLA) is regarded as a gold material because of its mechanical properties and degradability. In this study, we prepare MC/PLA composite scaffolds via in situ mineralization and freeze-drying. Cell, characterization, and animal experiments compare and evaluate the biomimetic properties and repair effects of the MC/PLA scaffolds. Phalloidin and DAPI staining results show that the MC/PLA scaffolds are not cytotoxic. CCK-8 and scratch experiments prove that the scaffolds are superior to MC and hydroxyapatite (HA)/PLA scaffolds in promoting cell proliferation and migration. The surface and interior of the MC/PLA scaffolds exhibit rich interconnected pore structures with a porosity of ≥70%. The XRD patterns are typical HA waveforms. X-ray, micro-CT, and H&E staining reveal that the defect boundary disappears, new bone tissue grows into MC/PLA scaffolds in a large area, and the scaffolds are degraded after six months of implantation. The MC/PLA composite scaffold has a pore structure and composition similar to cancellous bone, with a good biocompatibility and bone regeneration ability. [ABSTRACT FROM AUTHOR]

In recent years, functional ceramic devices have become smaller, thinner, more refined, and highly integrated, which makes it difficult to realize their rapid prototyping and low-cost manufacturing using traditional processing. As an emerging technology, multi-material 3D printing offers increased complexity and greater freedom in the design of functional ceramic devices because of its unique ability to directly construct arbitrary 3D parts that incorporate multiple material constituents without an intricate process or expensive tools. Here, the latest advances in multi-material 3D printing methods are reviewed, providing a comprehensive study on 3D-printable functional ceramic materials and processes for various functional ceramic devices, including capacitors, multilayer substrates, and microstrip antennas. Furthermore, the key challenges and prospects of multi-material 3D-printed functional ceramic devices are identified, and future directions are discussed. [ABSTRACT FROM AUTHOR]

Superconducting power lead equipment for epoxy insulation, such as high-temperature superconducting DC power or liquefied natural gas energy pipelines, as well as high-temperature superconducting cables, has long been used in extreme environments, from liquid nitrogen temperatures to normal temperatures. It is easy to induce surface discharge and flashover under the action of strong electric field, which accelerates the insulation failure of current leads. In this paper, two-dimensional nano-material GO was used to control the electrical properties of epoxy resins. The DC surface discharge and flashover characteristics of the prepared epoxy resin–GO composite insulation materials were tested at room temperature with liquid nitrogen. The surface discharge mechanism of the epoxy resin–GO composite insulation materials was analyzed. The experimental results show that the insulation properties of epoxy composites doped with GO changed. Among them, the surface flashover voltage of 0.05 wt% material is the best, which can inhibit the discharge phenomenon and improve its insulation properties in extreme environments, from room temperature to liquid nitrogen temperature. It is found that the development process of surface discharge of composite insulating materials under liquid nitrogen is quite different from that under room temperature. Before critical flashover, the repetition rate and amplitude of surface discharge remain at a low level until critical flashover. Furthermore, the voltage of the first flashover is significantly higher than that of the subsequent flashover under the action of the desorption gas on the surface of the composite insulating material and the gasification layer produced by the discharge. Given that the surface flashover voltage of 0.05 wt% epoxy composite is the best, the research and analysis of 0.05 wt% composite is emphasized. In the future design of superconducting power lead insulation, the modification method of adding GO to epoxy resin can be considered in order to improve its insulation performance. [ABSTRACT FROM AUTHOR]

This document is a correction notice for an article titled "Mineralized Collagen/Polylactic Acid Composite Scaffolds for Load-Bearing Bone Regeneration in a Developmental Model." The correction addresses an error in Figure 6 of the original publication, where figures A, B, and C were mistakenly mixed up from different sheep. The corrected Figure 6 has been provided, and the authors assure that the scientific conclusions remain unaffected. The original publication has been updated accordingly. [Extracted from the article]

Polyurethane (PU) foams are widely used as acoustic package materials to eliminate vehicle interior noise. Therefore, it is important to improve the acoustic performances of PU foams. In this paper, the grey relational analysis (GRA) method and multi-objective particle swarm optimization (MOPSO) algorithm are applied to improve the acoustic performances of PU foam composites. The average sound absorption coefficient and average transmission loss are set as optimization objectives. The hardness and content of Ethylene Propylene Diene Monomer (EPDM) and the content of deionized water and modified isocyanate (MDI) are selected as design variables. The optimization process of GRA method is based on the orthogonal arrays L 9 (3 4) , and the MOPSO algorithm is based on the Response Surface (RS) surrogate model. The results show that the acoustic performances of PU foam composites can be improved by optimizing the synthetic formula. Meanwhile, the results that were obtained by GRA method show the degree of influence of the four design variables on the optimization objectives, and the results obtained by MOPSO algorithm show the specific effects of the four design variables on the optimization objectives. Moreover, according to the confirmation experiment, the optimal synthetic formula is obtained by MOPSO algorithm when the weight coefficient of the two objectives set as 0.5. [ABSTRACT FROM AUTHOR]