Search

Differential code bias (DCB) of satellite is an error that cannot be ignored in precise positioning, timing, ionospheric modeling, satellite clock correction, and ambiguity resolution. The completion of the third generation of BeiDou Navigation Satellite System (BDS-3) has extended DCB to multichannel code bias observations and observable-specific signal bias (OSB). In this paper, the DCB and OSB products provided by the Chinese Academy of Sciences (CAS) are analyzed and compared. The DCB parameters for the BDS satellites are applied in both single- and dual-frequency single point positioning (SPP), and the results are intensively investigated. Based on the satellite DCB parameters of the BDS, the performance of precise point positioning (PPP) with different frequency combinations is also analyzed in terms of positioning accuracy and convergence time. The standard deviations (STDs) of DCBs at each signal pair fluctuate from 0.2 ns to 1.5 ns. The DCBs of BDS-2 are slightly more stable than those of BDS-3. The mean values and STDs of C2I and C7I OSBs for BDS-2 are at the same level and are numerically smaller than their counterparts for the C6I OSBs. The mean OSBs for each signal of the BDS-3, excluding C2I, fluctuate between 12.35 ns and 12.94 ns, and the STD fluctuates between 2.11 ns and 3.10 ns. The DCBs and OSBs of the BDS-3 of the IGSO satellites are more stable than those of the MEO satellites. The corrections for TGD and DCB are able to improve the accuracy of single-frequency SPP by 44.09% and 44.07%, respectively, and improve the accuracy of dual-frequency SPP by 6.44% and 12.85%, respectively. The most significant improvements from DCB correction are seen in single-frequency positioning with B1I and dual-frequency positioning with B2a+B3I. DCB correction can improve the horizontal and three-dimensional positioning accuracy of the dual-frequency PPP of different ionosphere-free combinations by 13.53% and 13.84% on average, respectively, although the convergence is slowed. [ABSTRACT FROM AUTHOR]

China has been facing serious land degradation and desertification in its north and northwest arid and semi-arid areas. Monitoring the dynamics of percentage vegetation cover (PVC) using remote sensing imagery in these areas has become critical. However, because these areas are large, remote, and sparsely populated, and also because of the existence of mixed pixels, there have been no accurate and cost-effective methods available for this purpose. Spectral unmixing methods are a good alternative as they do not need field data and are low cost. However, traditional linear spectral unmixing (LSU) methods lack the ability to capture the characteristics of spectral reflectance and scattering from endmembers and their interactions within mixed pixels. Moreover, existing nonlinear spectral unmixing methods, such as random forest (RF) and radial basis function neural network (RBFNN), are often costly because they require field measurements of PVC from a large number of training samples. In this study, a cost-effective approach to mapping PVC in arid and semi-arid areas was proposed. A method for selection and purification of endmembers mainly based on Landsat imagery was first presented. A probability-based spectral unmixing analysis (PBSUA) and a probability-based optimized k nearest-neighbors (PBOkNN) approach were then developed to improve the mapping of PVC in Duolun County in Inner Mongolia, China, using Landsat 8 images and field data from 920 sample plots. The proposed PBSUA and PBOkNN methods were further validated in terms of accuracy and cost-effectiveness by comparison with two LSU methods, with and without purification of endmembers, and two nonlinear approaches, RF and RBFNN. The cost-effectiveness was defined as the reciprocal of cost timing relative root mean square error (RRMSE). The results showed that (1) Probability-based spectral unmixing analysis (PBSUA) was most cost-effective and increased the cost-effectiveness by 29.3% 29.3%, 33.5%, 50.8%, and 53.0% compared with two LSU methods, PBOkNN, RF, and RBFNN, respectively; (2) PBSUA, RF, and RBFNN gave RRMSE values of 22.9%, 21.8%, and 22.8%, respectively, which were not significantly different from each other at the significance level of 0.05. Compatibly, PBOkNN and LSU methods with and without purification of endmembers resulted in significantly greater RRMSE values of 27.5%, 32.4%, and 43.3%, respectively; (3) the average estimates of the sample plots and predicted maps from PBSUA, PBOkNN, RF, and RBFNN fell in the confidence interval of the test plot data, but those from two LSU methods did not, although the LSU with purification of endmembers improved the PVC estimation accuracy by 25.2% compared with the LSU without purification of endmembers. Thus, this study indicated that the proposed PBSUA had great potential for cost-effectively mapping PVC in arid and semi-arid areas. [ABSTRACT FROM AUTHOR]

For the planning and sustainable management of forest resources, well-managed plantations are of great significance to mitigate the decrease of forested areas. Monitoring these planted forests is essential for forest resource inventories. In this study, two ALOS PALSAR-2 quad-polarimetric synthetic aperture radar (SAR) images and ground measurements were employed to estimate growing stem volume (GSV) of Chinese fir plantations located in a hilly area of southern China. To investigate the relationships between forest GSV and polarization characteristics, single and fused variables were derived by the Yamaguchi decomposition and the saturation value of GSV was estimated using a semi-exponential empirical model as a base model. Based on the estimated saturation values and relative root mean square error (RRMSE), the single and fused characteristics and corresponding models were selected and integrated, which led to a novel saturation-based multivariate method used to improve the GSV estimation and mapping of Chinese fir plantations. The new findings included: (1) All the original polarimetric characteristics, statistically, were not significantly correlated with the forest GSV, and their logarithm and ratio transformation fused variables greatly improved the correlations, thus the estimation accuracy of the forest GSV. (2) The logarithm transformation of surface scattering resulted in the greatest saturation, value but the logarithm transformation of double-bounce scattering resulted in the smallest RRMSE of the GSV estimates. (3) Compared with the single transformations, the fused variables led to more reasonable saturation values and obviously reduced the values of RRMSE. (4) The saturation-based multivariate method led to more accurate estimates of the forest GSV than the univariate method, with the smallest value (29.64%) of RRMSE achieved using the set of six variables. This implied that the novel saturation-based multivariate method provided greater potential to improve the estimation and mapping of the forest GSV. [ABSTRACT FROM AUTHOR]

Forest canopy height is one of the most important spatial characteristics for forest resource inventories and forest ecosystem modeling. Light detection and ranging (LiDAR) can be used to accurately detect canopy surface and terrain information from the backscattering signals of laser pulses, while photogrammetry tends to accurately depict the canopy surface envelope. The spatial differences between the canopy surfaces estimated by LiDAR and photogrammetry have not been investigated in depth. Thus, this study aims to assess LiDAR and photogrammetry point clouds and analyze the spatial differences in canopy heights. The study site is located in the Jigongshan National Nature Reserve of Henan Province, Central China. Six data sets, including one LiDAR data set and five photogrammetry data sets captured from an unmanned aerial vehicle (UAV), were used to estimate the forest canopy heights. Three spatial distribution descriptors, namely, the effective cell ratio (ECR), point cloud homogeneity (PCH) and point cloud redundancy (PCR), were developed to assess the LiDAR and photogrammetry point clouds in the grid. The ordinary neighbor (ON) and constrained neighbor (CN) interpolation algorithms were used to fill void cells in digital surface models (DSMs) and canopy height models (CHMs). The CN algorithm could be used to distinguish small and large holes in the CHMs. The optimal spatial resolution was analyzed according to the ECR changes of DSMs or CHMs resulting from the CN algorithms. Large negative and positive variations were observed between the LiDAR and photogrammetry canopy heights. The stratified mean difference in canopy heights increased gradually from negative to positive when the canopy heights were greater than 3 m, which means that photogrammetry tends to overestimate low canopy heights and underestimate high canopy heights. The CN interpolation algorithm achieved smaller relative root mean square errors than the ON interpolation algorithm. This article provides an operational method for the spatial assessment of point clouds and suggests that the variations between LiDAR and photogrammetry CHMs should be considered when modeling forest parameters. [ABSTRACT FROM AUTHOR]

There has been substantial research for estimating and mapping soil moisture content (SMC) of large areas using remotely sensed images by developing models of soil thermal inertia (STI). However, it is still a great challenge to accurately estimate SMC because of the impact of vegetation canopies and vegetation-induced shadows in mixed pixels on the estimates. In this study, a new method was developed to increase the estimation accuracy of SMC for an irrigated area located in YingKe of Heihe, China, using ASTER data. In the method, an original model of estimating bare STI was modified by decomposing a mixed pixel into three components, bare soil, vegetated soil, and shaded soil, as well as extracting their fractions using a spectral unmixing analysis and then deriving their fluxes. Moreover, the 90 m spatial resolution thermal images were scaled down to the 15 m spatial resolution by data fusion of a discrete wavelet transform (DWT) and re-sampling using the nearest neighbor method (NNM). The modified model was compared with the original model based on the mean absolute error (MAE) and relative root mean square error (RRMSE) between the SMC estimates and observations from 30 validation soil samples. The results indicated that compared to the original model based on the parallel dual layer, the modified STI model based on the serial dual layer statistically significantly decreased the MAE and RRMSE of the SMC estimates by 63.0–63.2% and 63.0–63.5%, respectively. The 15 m spatial resolution thermal bands obtained by the DWT data fusion provided more detailed information of SMC but did not significantly improve its estimation accuracy than the 15 m spatial resolution thermal bands by re-sampling using NNM. This implied that the novel method offered insights on how to increase the accuracy of retrieving SMC estimates in vegetated areas. [ABSTRACT FROM AUTHOR]

Accurately estimating growing stem volume (GSV) is very important for forest resource management. The GSV estimation is affected by remote sensing images, variable selection methods, and estimation algorithms. Optical images have been widely used for modeling key attributes of forest stands, including GSV and aboveground biomass (AGB), because of their easy availability, large coverage and related mature data processing and analysis technologies. However, the low data saturation level and the difficulty of selecting feature variables from optical images often impede the improvement of estimation accuracy. In this research, two GaoFen-2 (GF-2) images, a Landsat 8 image, and fused images created by integrating GF-2 bands with the Landsat multispectral image using the Gram–Schmidt method were first used to derive various feature variables and obtain various datasets or data scenarios. A DC-FSCK approach that integrates feature variable screening and a combination optimization procedure based on the distance correlation coefficient and k-nearest neighbors (kNN) algorithm was proposed and compared with the stepwise regression analysis (SRA) and random forest (RF) for feature variable selection. The DC-FSCK considers the self-correlation and combination effect among feature variables so that the selected variables can improve the accuracy and saturation level of GSV estimation. To validate the proposed approach, six estimation algorithms were examined and compared, including Multiple Linear Regression (MLR), kNN, Support Vector Regression (SVR), RF, eXtreme Gradient Boosting (XGBoost) and Stacking. The results showed that compared with GF-2 and Landsat 8 images, overall, the fused image (Red_Landsat) of GF-2 red band with Landsat 8 multispectral image improved the GSV estimation accuracy of Chinese pine and larch plantations. The Red_Landsat image also performed better than other fused images (Pan_Landsat, Blue_Landsat, Green_Landsat and Nir_Landsat). For most of the combinations of the datasets and estimation models, the proposed variable selection method DC-FSCK led to more accurate GSV estimates compared with SRA and RF. In addition, in most of the combinations obtained by the datasets and variable selection methods, the Stacking algorithm performed better than other estimation models. More importantly, the combination of the fused image Red_Landsat with the DC-FSCK and Stacking algorithm led to the best performance of GSV estimation with the greatest adjusted coefficients of determination, 0.8127 and 0.6047, and the smallest relative root mean square errors of 17.1% and 20.7% for Chinese pine and larch, respectively. This study provided new insights on how to choose suitable optical images, variable selection methods and optimal modeling algorithms for the GSV estimation of Chinese pine and larch plantations. [ABSTRACT FROM AUTHOR]

Uncertainties in forest aboveground biomass (AGB) estimates resulting from over- and underestimations using remote sensing data have been widely studied. The uncertainties may occur due to the spatial effects of the plot data. In this study, we collected AGB data from a total of 147 Pinus densata forest sample plots in Yunnan of southwestern China and analyzed the spatial effects on the estimation of AGB. An ordinary least squares (OLS) and four spatial regression methods were compared for the estimation using Landsat 8-OLI images. Through the spatial analysis of AGB and residuals of model predictions, it was found that the spatial autocorrelation and heterogeneity of the plot data could not be ignored. Compared with the OLS, the impact of the spatial effects on AGB estimation could be reduced slightly by the spatial lag model (SLM) and the spatial error model (SEM) and greatly reduced by the linear mixed effects model (LMM) and geographically weighted regression (GWR) based on the distributions of prediction residuals, global Moran's I, and Z score. The spatial regression models had better performance for model fitting and prediction because of the reduction in overestimations and underestimations for the forests with small and large AGB values, respectively. However, the reductions in the overestimations and underestimations varied depending on the spatial regression models. The GWR provided the most accurate predictions with the largest R2 (0.665), the smallest root mean square error (34.507), and mean relative error (−9.070%) by greatly reducing the AGB interval for overestimations occurring and significantly increasing the threshold of AGB from 150 Mg/ha to 200 Mg/ha for underestimations. Thus, GWR offered the greatest potential of improving the estimation of Pinus densata forest AGB in Yunnan of southwestern China. [ABSTRACT FROM AUTHOR]

Quickly and efficiently monitoring soil heavy metal content is crucial for protecting the natural environment and for human health. Estimating heavy metal content in soils using hyperspectral data is a cost-efficient method but challenging due to the effects of complex landscapes and soil properties. One of the challenges is how to make a lab-derived model based on soil samples applicable to mapping the contents of heavy metals in soil using air-borne or space-borne hyperspectral imagery at a regional scale. For this purpose, our study proposed a novel method using hyperspectral data from soil samples and the HuanJing-1A (HJ-1A) HyperSpectral Imager (HSI). In this method, estimation models were first developed using optimal relevant spectral variables from dry soil spectral reflectance (DSSR) data and field observations of soil heavy metal content. The relationship of the ratio of DSSR to moisture soil spectral reflectance (MSSR) with soil moisture content was then derived, which built up the linkage of DSSR with MSSR and provided the potential of applying the models developed in the laboratory to map soil heavy metal content at a regional scale using hyperspectral imagery. The optimal relevant spectral variables were obtained by combining the Boruta algorithm with a stepwise regression and variance inflation factor. This method was developed, validated, and applied to estimate the content of heavy metals in soil (As, Cd, and Hg) in Guangdong, China, and the Conghua district of Guangzhou city. The results showed that based on the validation datasets, the content of Cd could be reliably estimated and mapped by the proposed method, with relative root mean square error (RMSE) values of 17.41% for the point measurements of soil samples from Guangdong province and 17.10% for the Conghua district at the regional scale, while the content of heavy metals As and Hg in soil were relatively difficult to predict with the relative RMSE values of 32.27% and 28.72% at the soil sample level and 51.55% and 36.34% at the regional scale. Moreover, the relationship of the DSSR/MSSR ratio with soil moisture content varied greatly before the wavelength of 1029 nm and became stable after that, which linked DSSR with MSSR and provided the possibility of applying the DSSR-based models to map the soil heavy metal content at the regional scale using the HJ-1A images. In addition, it was found that overall there were only a few soil samples with the content of heavy metals exceeding the health standards in Guangdong province, while in Conghua the seriously polluted areas were mainly distributed in the cities and croplands. This study implies that the new approach provides the potential to map the content of heavy metals in soil, but the estimation model of Cd was more accurate than those of As and Hg. [ABSTRACT FROM AUTHOR]