Search

The increasing global warming trend has resulted in the mass loss of most glaciers. The Urumqi Vally, located in the dry and cold zone of China, and its widely dispersed glaciers are significant to the regional ecological environment, oasis economic development, and industrial and agricultural production. This is representative of glaciers in Middle Asia and represents one of the world's longest observed time series of glaciers, beginning in 1959. The Urumqi Headwater Glacier No. 1 (UHG-1) has a dominant presence in the World Glacier Monitoring Service (WGMS). This paper supplies a comprehensive analysis of past studies and future modeling of glacier changes in the Urumqi Valley. It has received insufficient attention in the past, and the mass balance of UHG-1 was used to verify that the geodetic results and the OGGM model simulation results are convincing. The main conclusions are: The area of 48.68 ± 4.59 km2 delineated by 150 glaciers in 1958 decreased to 21.61 ± 0.27 km2 delineated by 108 glaciers in 2022, with a reduction of 0.47 ± 0.04 km2·a−1 (0.96% a−1 in 1958–2022). The glacier mass balance by geodesy is −0.69 ± 0.11 m w.e.a−1 in 2000–2022, which is just deviating from the measured result (−0.66 m w.e.a−1), but the geodetic result in this paper can be enough to reflect the glacier changes (−0.65 ± 0.11 m w.e.a−1) of the URB in 2000–2022. The future loss rate of area and volume will undergo a rapid and then decelerating process, with the fastest and slowest inflection points occurring around 2035 and 2070, respectively. High temperatures and large precipitation in summer accelerate glacier loss, and the corresponding lag period of glacier change to climate is about 2–3 years. [ABSTRACT FROM AUTHOR]

Spartina alterniflora (S. alterniflora) has grown rapidly in China since its introduction in 1979, showing the trend of alien species invasion, which has seriously affected the ecosystem balance of coastal wetlands. The temporal and spatial expansion law of S. alterniflora can be obtained through remote sensing monitoring, which can provide a reference and basis for S. alterniflora management. This paper presents a method for extracting and mapping S. alterniflora based on phenological characteristics. The coastal areas of the Yangtze River Delta Urban Agglomeration are selected as the research area, and the Landsat time series data from 1990 to 2022 on the Google Earth Engine (GEE) platform are used to support the experiment in this paper. Firstly, the possible growing area of S. alterniflora was extracted using the normalized differential moisture index (NDMI), normalized differential vegetation index (NDVI), and normalized differential water index (NDWI); Then, the time series curve characterizing the phenological characteristics of vegetation was constructed using the vegetation index to determine the difference phase of phenological characteristics between S. alterniflora and other vegetation. Finally, a decision tree was constructed based on the phenological feature difference phase data to extract S. alterniflora, and it is applied to the analysis of temporal and spatial changes of S. alterniflora in the study area from 1990 to 2022. The results show that the area of S. alterniflora increased from ~1426 ha in 1990 to ~44,508 ha in 2022. However, the area of S. alterniflora began to show negative growth in 2015 due to the construction of nature reserves and ecological management. The results of correlation analysis showed that the growth of C. japonicum was significantly affected by temperature stress and weakly affected by precipitation. This study verified that Landsat time series images can effectively extract vegetation phenological information, which has strong feasibility for extraction and dynamic monitoring of S. alterniflora and provides technical support for the management and monitoring of invasive plants in coastal wetlands. [ABSTRACT FROM AUTHOR]

Haiyang-2A (HY-2A) is the first marine dynamic environment satellite established by China, which has made significant contributions to the marine scientific research field. It carries the satellite-based GPS receiver named HY2, which was independently developed by China. It is an experimental satellite-borne GPS receiver for low earth orbit satellites, and during its operational period in orbit, the satellite-borne GPS data are not made accessible to the public. Therefore, this paper assesses the quality of HY-2A satellite-borne GPS data based on indicators such as satellite visibility, multipath effect, and ionospheric delay. The results indicate that the data acquired by the HY2 receiver are of high quality. The precise orbit determination (POD) uses the reduced-dynamic (RD) method. The adjustment effects of the pseudo-stochastic pulse time interval and a priori sigma on POD are analyzed, and the antenna phase center variation (PCV) is estimated using the direct method and residual method. Furthermore, this paper investigates the impact of PCV models with different resolutions (10° × 10° and 5° × 5°) on satellite orbit determination. To evaluate the orbit precision, three methods are used for validation, including carrier phase residual analysis, external precise science orbit (PSO) validation, and SLR three-dimensional (3D) validation, respectively. The results indicate that the highest orbit precision is achieved when the pseudo-stochastic pulse time interval is configured to 15 min, with the a priori sigma of 1 × 10−8 m/s2. The orbit carrier phase residuals reach the millimeter level. The 10° × 10°PCV model was estimated using the direct method and residual method, respectively; the root mean square of the external orbit validation for both methods show a millimeter-level improvement. The results obtained from the direct method and residual method are comparable. The resolution is increased from 10° to 5°, and the improvement in orbital precision is relatively small. The results obtained from the SLR 3D validation are consistent with those from the external PSO validation. The experimental results contribute valuable information for the POD of the HY2 series satellites. [ABSTRACT FROM AUTHOR]

Understanding changes of soil organic carbon (SOC) in top layers of croplands and their driving factors is a vital prerequisite in decision-making for maintaining sustainable agriculture. However, high-precision estimation of SOC of croplands at regional scale is still an issue to be solved. Based on soil samples, synthetic image of bare soil and geographical data, this paper predicted SOC density of croplands using Random Forest model in the Black Soil Region of Jilin Province, China in 2005 and 2020, and analyzed its influencing factors. Results showed that random forest model that integrates bare soil composite images improve the accuracy and robustness of SOC density prediction. From 2005 to 2020, the total SOC storage in croplands decreased from 89.96 to 82.79 Tg C with an annual decrease of 0.48 Tg C yr−1. The mean value of SOC density of croplands decreased from 3.42 to 3.32 kg/m2, and high values are distributed in middle parts. Changes of SOC represented significant heterogeneity spatially. 62.14% of croplands with SOC density greater than 4.0 kg/m2 decreased significantly, and 38.60% of croplands with SOC density between 2.5 and 3.0 kg/m2 significantly increased. Climatic factors made great contributions to SOC density, however, their relative importance (RI) to SOC density decreased from 44.65% to 37.26% during the study period. Synthetic images of bare soil constituted 23.54% and 26.29% of RI in the SOC density prediction, respectively, and the contribution of each band was quite different. The RIs of topographic and vegetation factors were low but increased significantly from 2005 to 2020. This study can aid local land managers and governmental agencies in assessing carbon sequestration potential and carbon credits, thus contributing to the protection and sustainable use of black soils. [ABSTRACT FROM AUTHOR]

In unconventional oil and gas development, the hydraulic fracturing (HF) technique is adopted to inject high-pressure fluid into the reservoir and change its pore-fracture connection structure to enhance production. HF causes the rocks to crack and generates microseismic events (with moment magnitudes of M w ≤ 3 ). Studying the microseismic focal mechanisms (shear/tensile/compressive HF cracks) is helpful for characterizing fracture geometry, monitoring the in situ stress state, and evaluating the HF effects to optimize the reservoir reconstruction for increasing production. Due to fluid injection activity, there may be non-double-couple (non-DC) mechanisms associated with HF cracks, and the commonly used double-couple (DC) source model may not be suitable. For the moment tensor (MT) source model, which is commonly used to describe the non-DC mechanism, inversion is challenging in single-well monitoring. The shear-tensile general dislocation (GD) model includes a non-DC mechanism, and its inversion is more constrained than the full MT model by specifying the focal mechanism as shear-tensile (or compressive) faulting. This paper reports a focal mechanism inversion case study of HF shear/tensile/compressive cracks in a tight oil reservoir in the Ordos Basin, China. We perform inversions based on the DC, GD, and MT source models, respectively. The results indicate that, for the downhole monitoring geometry in this study, most of the DC inversions fail to obtain proper synthetic and observed waveform fitting results, and the MT inversion results of different microseismic events exhibit worse consistencies than the GD results. According to the GD results, almost all the HF cracks can be explained as strike-slip faulting and most cracks correspond to non-negligible tensile/compressive mechanisms. Our study suggests that the GD source model is preferred in downhole microseismic monitoring to obtain reliable shear/tensile/compressive HF cracks, and the inverted non-zero slope angle reduces the uncertainty in fracturing geometry characterization, which will help improve microseismic studies and HF evaluations for enhanced resource recovery. [ABSTRACT FROM AUTHOR]

Before 2008, China lacked high-coverage regional surface observation data, making it difficult for the China Meteorological Administration Land Data Assimilation System (CLDAS) to directly backtrack high-resolution, high-quality land assimilation products. To address this issue, this paper proposes a deep learning model named UNET_DCA, based on the UNET architecture, which incorporates a Dual Cross-Attention module (DCA) for multiscale feature fusion by introducing Channel Cross-Attention (CCA) and Spatial Cross-Attention (SCA) mechanisms. This model focuses on the near-surface 10-m wind field and achieves spatial downscaling from 6.25 km to 1 km. We conducted training and validation using data from 2020–2021, tested with data from 2019, and performed ablation experiments to validate the effectiveness of each module. We compared the results with traditional bilinear interpolation methods and the SNCA-CLDASSD model. The experimental results show that the UNET-based model outperforms SNCA-CLDASSD, indicating that the UNET-based model captures richer information in wind field downscaling compared to SNCA-CLDASSD, which relies on sequentially stacked CNN convolution modules. UNET_CCA and UNET_SCA, incorporating cross-attention mechanisms, outperform UNET without attention mechanisms. Furthermore, UNET_DCA, incorporating both Channel Cross-Attention and Spatial Cross-Attention mechanisms, outperforms UNET_CCA and UNET_SCA, which only incorporate one attention mechanism. UNET_DCA performs best on the RMSE, MAE, and COR metrics (0.40 m/s, 0.28 m/s, 0.93), while UNET_DCA_ars, incorporating more auxiliary information, performs best on the PSNR and SSIM metrics (29.006, 0.880). Evaluation across different methods indicates that the optimal model performs best in valleys, followed by mountains, and worst in plains; it performs worse during the day and better at night; and as wind speed levels increase, accuracy decreases. Overall, among various downscaling methods, UNET_DCA and UNET_DCA_ars effectively reconstruct the spatial details of wind fields, providing a deeper exploration for the inversion of high-resolution historical meteorological grid data. [ABSTRACT FROM AUTHOR]

Knowledge of wind field characteristics and variation principles in complex topographical regions is of great importance for the development of numerical prediction models, aviation safety support, and wind energy utilization. However, there has been limited research focused on the lower-tropospheric wind fields in the Qinghai-Tibet Plateau. This paper aims to study the wind characteristics, vertical distributions, and temporal variations in the northeast of the plateau by analyzing a four-year continuous dataset collected from a Doppler wind LiDAR deployed in Xining, Qinghai Province of China. The results indicate that the prevailing horizontal wind direction in the low levels is primarily influenced by the mountain-valley wind circulation. However, as the altitude increases, the prevailing winds are predominantly affected by the westerlies. From a diurnal perspective, noticeable transition processes between up-valley and down-valley winds can be observed. The west-northwest wind (down-valley wind) dominates from late night to morning, while the east-southeast wind (up-valley wind) prevails from afternoon to early evening. The vertical winds in the low levels exhibit a downward motion during the daytime and an upward motion during the nighttime. In this plateau valley, the wind shear exponent is found to be highest in spring and lowest in winter, and it is generally lower during the daytime compared to the nighttime. [ABSTRACT FROM AUTHOR]

Winter wheat is a significant global food crop, and it is crucial to monitor its distribution for better agricultural management, land planning, and environmental sustainability. However, the distribution style of winter wheat planting fields is not consistent due to different terrain conditions. In mountainous areas, winter wheat planting units are smaller in size and fragmented in distribution compared to plain areas. Unfortunately, most crop-mapping research based on deep learning ignores the impact of topographic relief on crop distribution and struggles to handle hilly areas effectively. In this paper, we propose a cross-modal segmentation network for winter wheat mapping in complex terrain using remote-sensing multi-temporal images and DEM data. First, we propose a diverse receptive fusion (DRF) module, which applies a deformable receptive field to optical images during the feature fusion process, allowing it to match winter wheat plots of varying scales and a fixed receptive field to the DEM to extract evaluation features at a consistent scale. Second, we developed a distributed weight attention (DWA) module, which can enhance the feature intensity of winter wheat, thereby reducing the omission rate of planting areas, especially for the small-sized regions in hilly terrain. Furthermore, to demonstrate the performance of our model, we conducted extensive experiments and ablation studies on a large-scale dataset in Lanling county, Shandong province, China. Our results show that our proposed CM-Net is effective in mapping winter wheat in complex terrain. [ABSTRACT FROM AUTHOR]

The continuous downward movement exhibited by the Lashagou landslide group in recent years poses a significant threat to the safety of both vehicles and pedestrians traversing the highway G310. By integrating geomorphological interpretation using multi-temporal optical images, interferometric synthetic aperture radar (InSAR) measurements, and continuous global navigation satellite system (GNSS) observations, this paper traced the formation period of the Lashagou landslide group, and explored its kinematic behavior under external drivers such as rainfall and snowmelt. The results indicate that the formation period can be specifically categorized into three periods: before, during, and after the construction of highway G310. The construction of highway G310 is the direct cause and prerequisite for the formation of the Lashagou landslide group, whereas summer precipitation and spring snowmelt are the external driving factors contributing to its continuous downward movement. Additionally, both the long-term seasonal downslope movement and transient acceleration events are strongly controlled by rainfall, and there is a time lag of approximately 1–2 days between the transient acceleration and heavy rainfall events. This study highlights the benefits of leveraging multi-source remote sensing data to investigate slow-moving landslides, which is advantageous for the implementation of effective control and engineering intervention to mitigate potential landslide disasters. [ABSTRACT FROM AUTHOR]

The "Yangtze River Economic Belt Development Strategy" is one of China's three major national development strategies. Enhancing the protection and quality of arable land in the Yangtze River Economic Belt (YEB) is pivotal for fostering regional growth. In this study, land use data spanning the years 1980 to 2020 in the YEB were extracted from the national land use database maintained by the Resource and Environment Data Center of the Chinese Academy of Sciences. Employing Geographic Information System (GIS) spatial analysis techniques and arable land change metrics, the study delineated the spatiotemporal characteristics of arable land alterations across the YEB for the period. Additionally, using grain output data at the prefecture level from 2011 to 2020, the paper calculated provincial grain output to analyze the impact of arable land changes over the last four decades on grain output. The findings revealed that: (1) From 1980 to 2020, the total arable land area in the YEB decreased by approximately 41,775 square kilometers, with the most significant decrease occurring in the downstream region. (2) From 1980 to 1990, the primary factor contributing to the decrease in arable land area was the expansion of water bodies, while from 1990 to 2020, the principal reason for the reduction in arable land area was the expansion of construction land. (3) From 1980 to 2020, the decrease in arable land area resulted in a net reduction of approximately 25.12 million tons in total grain output, with the largest decline observed in the downstream regions and the smallest decline in the upstream regions. (4) Consistent with the trends in arable land area reduction, the main reason for the decline in grain output from 1980 to 1990 was the expansion of water bodies encroaching upon arable land, whereas from 2000 to 2010, the primary cause of arable land reduction was the expansion of construction land areas. In conclusion, the research suggested that over the past four decades, the primary driver behind the reduction in arable land within the YEB has been the expansion of construction land areas. Particularly noteworthy was the period from 2000 to 2010, during which the impact of arable land reduction on grain output was most pronounced. This period coincided with the rapid economic development and accelerated urbanization process within the YEB. [ABSTRACT FROM AUTHOR]

Freeze–thaw (FT) erosion intensity may exhibit a future increasing trend with climate warming, humidification, and permafrost degradation in the Qinghai–Tibet Plateau (QTP). The present study provides a reference for the prevention and control of FT erosion in the QTP, as well as for the protection and restoration of the regional ecological environment. FT erosion is the third major type of soil erosion after water and wind erosion. Although FT erosion is one of the major soil erosion types in cold regions, it has been studied relatively little in the past because of the complexity of several influencing factors and the involvement of shallow surface layers at certain depths. The QTP is an important ecological barrier area in China. However, this area is characterized by harsh climatic and fragile environmental conditions, as well as by frequent FT erosion events, making it necessary to conduct research on FT erosion. In this paper, a total of 11 meteorological, vegetation, topographic, geomorphological, and geological factors were selected and assigned analytic hierarchy process (AHP)-based weights to evaluate the FT erosion intensity in the QTP using a comprehensive evaluation index method. In addition, the single effects of the selected influencing factors on the FT erosion intensity were further evaluated in this study. According to the obtained results, the total FT erosion area covered 1.61 × 106 km2, accounting for 61.33% of the total area of the QTP. The moderate and strong FT erosion intensity classes covered 6.19 × 105 km2, accounting for 38.37% of the total FT erosion area in the QTP. The results revealed substantial variations in the spatial distribution of the FT erosion intensity in the QTP. Indeed, the moderate and strong erosion areas were mainly located in the high mountain areas and the hilly part of the Hoh Xil frozen soil region. [ABSTRACT FROM AUTHOR]

The Ozone Monitoring Suite-Nadir (OMS-N) instrument is the first hyperspectral remote sensor in the ultraviolet band of China's Fengyun series satellites. It can be used to detect several kinds of atmospheric constituents. This paper describes the prelaunch spectral calibration of the OMS-N onboard FengYun 3F. Several critical spectral parameters including the spectral resolution, spectral dispersion, and the instrument spectral response function were determined through laser-based measurements. A secondary peak of the instrument spectral response function from the short wavelength side of the ultraviolet band was found, and the possible influence on data applications was analyzed using a reference solar model and radiative transfer model. The results indicate that the spectral resolution and spectral accuracy of OMS-N meet the mission requirements. However, the asymmetries in the instrument spectral response function in the ultraviolet band were found near nadir rows, which are expressed as the "asymmetric central peak" and "secondary peak". The analysis results show that if the influences of the instrument spectral response function "asymmetric central peak" and "secondary peak" in the ultraviolet band are ignored, they will bring an error as large as 5% at the center of the absorption line. [ABSTRACT FROM AUTHOR]

Research on wildlife monitoring methods is a crucial tool for the conservation of rare wildlife in China. However, the fact that rare wildlife monitoring images in field scenes are easily affected by complex scene information, poorly illuminated, obscured, and blurred limits their use. This often results in unstable recognition and low accuracy levels. To address this issue, this paper proposes a novel wildlife identification model for rare animals in Giant Panda National Park (GPNP). We redesigned the C3 module of YOLOv5 using NAMAttention and the MemoryEfficientMish activation function to decrease the weight of field scene features. Additionally, we integrated the WIoU boundary loss function to mitigate the influence of low-quality images during training, resulting in the development of the NMW-YOLOv5 model. Our model achieved 97.3% for mAP50 and 83.3% for mAP50:95 in the LoTE-Animal dataset. When comparing the model with some classical YOLO models for the purpose of conducting comparison experiments, it surpasses the current best-performing model by 1.6% for mAP50:95, showcasing a high level of recognition accuracy. In the generalization ability test, the model has a low error rate for most rare wildlife species and is generally able to identify wildlife in the wild environment of the GPNP with greater accuracy. It has been demonstrated that NMW-YOLOv5 significantly enhances wildlife recognition accuracy in field environments by eliminating irrelevant features and extracting deep, effective features. Furthermore, it exhibits strong detection and recognition capabilities for rare wildlife in GPNP field environments. This could offer a new and effective tool for rare wildlife monitoring in GPNP. [ABSTRACT FROM AUTHOR]

Microwave hyperspectral instruments represent one of the main atmospheric sounders of China's next-generation Fengyun meteorological satellites. In order to better apply microwave hyperspectral observations in the fields of atmospheric parameter retrieval and data assimilation, this paper analyzes the sensitivity of trace gases to five selected bandwidth channels using a radiative transfer model based on the simulated data of microwave hyperspectral radiances at 50–60 GHz. This method uses information entropy and a weighting function to select channels and analyze the impact of this on the retrieval accuracy of atmospheric profiles before and after channel selection. The experimental results show that channel selection can reduce the number of channels by approximately 74.05% while maintaining a large amount of information content, and this retrieval effect is significantly better than that of MWTS-III. After channel selection, the 10 MHz, 30 MHz, and 50 MHz bandwidths have the best retrieval results in the stratosphere, whole atmosphere, and troposphere, respectively. When considering the number of channels, computational scale, and retrieval results comprehensively, the channel selection method is effective. [ABSTRACT FROM AUTHOR]

The investigation of reactivated landslides in the alpine-canyon areas suffers the difficult accessibility of precipitous terrain. In particular, when reactivated landslides occur along the major roads, efforts are focused on measuring ground surface displacements during road construction. Nevertheless, the ancient landslide deposits may reactivate after several years of road operation, while they show a stable state during the road construction. The characterization of this type of reactivated landslides is challenging, due to their complex mechanism and the limited monitoring data. Appropriate multi-source data can provide insights into deformation fields and enhance the understanding of landslide mechanisms, ensuring the outperformance of remedial works. This paper reports a recent Tangjiawan reactivated landslide along the Wenchuan-Maerkang Highway in Li County, China. The outcomes, including satellite InSAR, in situ real-time monitoring, and detailed ground and UAV investigation, conducted at this landslide are presented. Early deformation of the reactivated landslide began from 2019, with an InSAR-derived velocity of −11.7 mm/year, furthermore, a significant subsidence of about 21.2 mm, which occurred within a span of only 12 days from 3 June 2020 to 15 June 2020, was observed. The deformation characteristics derived from in situ monitoring during the remedial works were likely firstly associated with the initial unreinforced slope condition and the heavy rainfall. Subsequently, the displacement evolution transformed into deformation induced by time-dependent reduction in slope strength under rainfall conditions. The existing of unconsolidated deposits derived from ancient landslides, along with a fragile geo-structure consisting of rock blocks and gravels interlayered with breccias, exacerbated by large relief created a predisposition for landslide reactivation. Furthermore, 13 days of antecedent cumulative rainfall totaling 224.5 mm directly triggered the occurrence of a landslide event. The significance and implications of integrating multiple monitoring techniques are emphasized. [ABSTRACT FROM AUTHOR]

Precipitation is the basic component of the Earth's water cycle. Obtaining high-resolution and high-precision precipitation data is of great significance. This paper establishes a precipitation retrieval model based on a random forest classification and regression model during the day and at night with FY-4B/AGRI Level1 data on China from July to August 2022. To evaluate the retrieval effect of the model, the GPM IMERG product is used as a reference, and the retrieval results are compared against those of the FY-4B/AGRI operational precipitation product. In addition, the retrieval results are analyzed according to different underlying surfaces. The results showed that compared with the FY-4B/AGRI operational precipitation product, the retrieval model can better identify precipitation and capture precipitation areas of light rain, moderate rain, heavy rain and torrential rain. Among them, the probability of detection (POD) of the day model increased from 0.328 to 0.680, and the equitable threat score (ETS) increased from 0.252 to 0.432. The POD of the night model increased from 0.337 to 0.639, and the ETS score increased from 0.239 to 0.369. Meanwhile, the precipitation estimation accuracy of the day model increased by 38.98% and that of the night model increased by 40.85%. Our results also showed that due to the surface uniformity of the ocean, the model can identify precipitation better on the ocean than on the land. Our findings also indicated that for the different underlying surfaces of the land, there is no significant difference in each evaluation index of the model. This is a strong argument for the universal applicability of the model. Notably, the results showed that, especially for more vegetated areas and areas covered by water, the model is capable of estimating precipitation. In conclusion, the precipitation retrieval model that is proposed herein can better determine precipitation regions and estimate precipitation intensities compared with the FY-4B/AGRI operational precipitation product. It can provide some reference value for future precipitation retrieval research on FY-4B/AGRI. [ABSTRACT FROM AUTHOR]

The accurate estimation of forest aboveground biomass is of great significance for forest management and carbon balance monitoring. Remote sensing instruments have been widely applied in forest parameters inversion with wide coverage and high spatiotemporal resolution. In this paper, the capability of different remote-sensed imagery was investigated, including multispectral images (GaoFen-6, Sentinel-2 and Landsat-8) and various SAR (Synthetic Aperture Radar) data (GaoFen-3, Sentinel-1, ALOS-2), in aboveground forest biomass estimation. In particular, based on the forest inventory data of Hangzhou in China, the Random Forest (RF), Convolutional Neural Network (CNN) and Convolutional Neural Networks Long Short-Term Memory Networks (CNN-LSTM) algorithms were deployed to construct the forest biomass estimation models, respectively. The estimate accuracies were evaluated under the different configurations of images and methods. The results show that for the SAR data, ALOS-2 has a higher biomass estimation accuracy than the GaoFen-3 and Sentinel-1. Moreover, the GaoFen-6 data is slightly worse than Sentinel-2 and Landsat-8 optical data in biomass estimation. In contrast with the single source, integrating multisource data can effectively enhance accuracy, with improvements ranging from 5% to 10%. The CNN-LSTM generally performs better than CNN and RF, regardless of the data used. The combination of CNN-LSTM and multisource data provided the best results in this case and can achieve the maximum R2 value of up to 0.74. It was found that the majority of the biomass values in the study area in 2018 ranged from 60 to 90 Mg/ha, with an average value of 64.20 Mg/ha. [ABSTRACT FROM AUTHOR]

Thermodynamic and liquid water profiles can be retrieved by a ground-based microwave radiometer (MWR) in nearly all weather conditions, which is useful for detecting mesoscale phenomena. This paper reviews the advances in remote sensing of atmospheric profiles and cloud properties by MWR in central China. Comparative studies indicate that MWR retrieval accuracy is different under various skies, especially those that decay under precipitation. The off-zenith method is proven to be capable of reducing the impact of precipitation and snow on MWR retrieval accuracy. Application studies demonstrate that MWR retrievals are helpful for early warning of rainstorms, hailstorms, and thunderstorms. Moreover, MWR retrievals provide a way to study cloud properties. The temporal variations of cloud occurrence frequency (COF) and liquid water path (LWP) are different for low, middle, and high clouds, and the vertical distribution of COF is also different in autumn and other seasons. Note that MWR can infer valid retrievals over the eastern Tibetan Plateau due to the weak precipitation over there. Also, cloud properties over the eastern Tibetan Plateau present differences from those over central China, and this is related to the different characteristics of atmospheric water vapor between these two regions. To bring more benefits for mechanism study and early warning of severe weather and numerical weather prediction, the decayed accuracy of MWR zenith retrievals under precipitation should be resolved. And combining MWR with other instruments is necessary for MWR application in detecting multi-layer clouds and ice clouds. [ABSTRACT FROM AUTHOR]

In this paper, multi-source observation, such as aircraft, ground-based remote sensing, and satellite-retrieved data, has been utilized to compare and analyze the vertical characteristics of aerosol optical properties and the planetary boundary layer height (HPBL) over the North China Plain (NCP) region during May–June 2016. Aircraft observations show the vertical profiles of aerosol absorption coefficients (σabs), scattering coefficients (σsca), and extinction coefficients (σext) gradually decrease with altitude, with their maximum values near HPBL. The vertical profiles of σext depended most on the vertical distribution of measured σsca, indicating a significant contribution of scattering aerosols. In addition, the prominent characteristic of the inverse relationship between σext and moisture profile could serve as a reference for predicting air quality in the NCP region. The lower layer pollution during the field experiment was likely caused by the accumulation of fine-mode aerosols, characterized by the vertical distribution of the Ångström exponent and the Aerosol Robotic Network (AERONET) products. Typically, HPBL derived from aircraft and surface Micro Pulse Lidar (MPL) was approximate, while the predicted HPBL by meteorological data indicates an underestimation of ~192 m. Aerosol optical depth (AOD) calculated from aircraft and ground-based remote sensing (such as MPL and AERONET) experienced a strong correlation, and both of them exhibited a similar tendency. However, the AOD retrieved from satellites was significantly larger than that from aircraft and ground-based remote sensing. Overall, the inversion algorithm, cloud identification algorithm, representativeness of the space, and time of the observation may lead to an overestimation or underestimation of AOD under certain circumstances. This study may serve as a re-evaluation of AOD retrieved from multi-source observations and provide a reference to uncover the actual atmospheric environment in the NCP regions. [ABSTRACT FROM AUTHOR]

Mountainous terrains are typical over southeast China, with complex and diverse topography, large terrain undulations, rich geographic features, and meteorological variations. Previous studies show that ERA5 meteorological variables are generally accurate with respect to large plains or urban agglomerations, while their applicability to mountainous areas remains inconclusive. In this paper, using high-precision measurements probed by ground-based remote sensing instruments in May–July 2023 at a typical mountainous Shanghuang site in southeast China, the vertical accuracy of the ERA5 reanalysis datasets were comparatively evaluated. Our findings depict that the horizontal wind speeds of the ERA5 reanalysis data show a good performance compared to the Doppler lidar observations. In quantitative terms, ERA5 horizontal wind speeds are about 8% higher than the observed values below a height of 400 m, while above 400 m, an increasing negative bias is observed along as altitude increases. Differing from the horizontal wind speeds, there is a large discrepancy in the vertical wind speeds between the ERA5 and the observations, with a deviation of −150% to 40%. In terms of the thermal variables, the temperature extracted from ERA5 are consistent with the measurements in the low troposphere. Nevertheless, large systematic errors occur at 2000–3000 m, and the overall presentation shows that the errors gradually increase with the increase in altitude. Concerning the relative humidity, the general trend in ERA5 is similar to that observed by the microwave radiometer, but the relative errors from 500 to 2500 m range from 40% to 100%. This study also reveals that ERA5 is poorly representative and requires further improvements during extreme weather events such as rainstorms and typhoons. In particular, the horizontal wind speeds at the middle and lower levels deviate strongly from the observations. Given the importance of atmospheric thermodynamic stratifications in terms of both environmental and climatic issues, the results expand the application of the ERA5 reanalysis datasets in the mountainous areas of southeast China. More importantly, it provides credible reference data for the meteorological predictions and climate modelings in the southeast China mountainous region. [ABSTRACT FROM AUTHOR]

A trend in the development of spaceborne Synthetic Aperture Radar (SAR) technology is the shift from a single-satellite repeated observation mode to a multi-satellite collaborative observation mode. However, current multi-satellite collaborative geolocation algorithms face challenges, such as geometric model mismatch and poor baseline estimation accuracy, arising from highly dynamic changes among multi-satellites. This paper introduces a high-precision and efficient geolocation algorithm for a spaceborne bistatic interferometric SAR (BiInSAR) system based on an improved range–Doppler (IRD) model. The proposed algorithm encompasses three key contributions. Firstly, a comprehensive description of the spatial baseline geometric model unique to the bistatic configuration is provided, with a specific focus on deriving the perpendicular baseline expression. Secondly, IRD geolocation functions are established to meet the specific requirements of the bistatic configuration. Then, a novel BiInSAR geolocation algorithm based on the IRD's functions is proposed, which can significantly improve the target geolocation accuracy by modifying the range–Doppler equation to suit the bistatic configuration. Meanwhile, a low-coupling parallel calculation method is proposed, which can improve the calculation speed by two to three times. Finally, the accuracy and efficiency of the algorithm are demonstrated using experimental data acquired by the TH-2 satellite, which is China's first spaceborne BiInSAR system. The experimental results prove that the IRD algorithm exhibits geolocation accuracy with an average error of less than 1 m and a standard deviation of less than 2.5 m while maintaining computational efficiency at a calculation speed of 1,429,678 pixels per second. [ABSTRACT FROM AUTHOR]

In typical alteration extraction methods, e.g., band math and principal component analysis (PCA), the bands or band combinations unitized to extract altered minerals are usually selected based on empirical models or previous rules. This results in significant differences in the alteration of mineral mapping even in the same area, thus greatly increasing the uncertainty of mineral resource prediction. In this paper, an intelligent alteration extraction approach was proposed in which an optimization algorithm, i.e., a genetic algorithm (GA), was introduced into the PCA; this approach is termed GA-PCA and is used for selecting the optimized band combinations of mineralized alterations. The proposed GA-PCA was employed to map iron oxides and hydroxyl minerals using the most commonly adopted multispectral data, i.e., Landsat-8 OLI data, at the Lalingzaohuo polymetallic deposits, China. The results showed that the spectral characteristics of GA-PCA-selected OLI band combinations in the research area were beneficial for enhancing alteration information and were more capable of suppressing the interference of vegetation information. The mapping alteration zones using the GA-PCA approach had a higher agreement with known ore spots, i.e., 25% and 33.3% in ferrous-bearing and hydroxyl-bearing deposits, compared to the classical PCA. Furthermore, two predicted targets (not shown in the classical PCA results) were precisely obtained via analyzing the GA-PCA alteration maps combined with the ore-forming geological conditions of the mine and its tectonic characteristics. This indicated that the intelligent selection of mineral alteration band combinations increased the reliability of remote sensing-based mineral exploration. [ABSTRACT FROM AUTHOR]

Underground coal-mining-induced ground subsidence deformation is a common geological disaster impacting buildings, transportation and water supplies. Models predicting ground subsidence dynamically with high precision are important for the prevention of damage derived from ground subsidence. In this paper, the Hook function is utilized to develop a model describing the velocity of ground subsidence due to underground coal mining. Based on the subsidence velocity model, a dynamic subsidence model is established by taking an integral of the velocity model. Coefficients of the model, which depend on maximum subsidence, maximum subsidence velocity and the time corresponding to the maximum subsidence velocity, are related to the geological and mining conditions of the coal seam being investigated. A Levenberg–Marquardt-algorithm-based method is also proposed to calculate the optimal model coefficients based on subsidence velocity observations. Four continuously operating Global Navigation Satellite System (GNSS) stations were constructed above a typical longwall coal mining working face in the Jining mining area, China. These GNSS stations collected subsidence observations over two years, which were used to validate the developed prediction model. The results show that the root-mean-square (RMS) of the model-predicted ground subsidence error is 56.1 mm, and the maximum relative error is 2.5% for all four GNSS stations, when the ground subsidence is less than 6000 mm. [ABSTRACT FROM AUTHOR]

Long-distance water transfer is a critical engineering measure to rectify disparities in water resource distribution across regions. The effective operation and safety of such projects are paramount to their success, as localized issues can have cascading consequences, potentially disrupting the entire network. Conventional ground-based monitoring methods have limitations in measuring the deformation of large-scale structures. In this paper, InSAR is employed to monitor the deformation of the Shuangwangcheng (SWC) Reservoir, which features a long embankment dam as part of the South-to-North Water Diversion Project in China. We utilize data from both Sentinel-1 and TerraSAR-X satellites to derive 7-year deformation. Results reveal that the entire dam experiences continuous subsidence, with the maximum deformation in the line-of-sight direction measuring ~160 mm. While minor differential settlements are noted in different sections of the dam, the gradient is not significant due to the dam's substantial length. The InSAR deformation results from multiple geometries demonstrate good consistency, with the highest correlation observed between the Sentinel-1 ascending and descending datasets, exceeding 0.9. Validation against the GNSS observations of the three sites on the SWC Dam shows the accuracy of InSAR displacements is ~8 mm. Water level changes do impact deformation, but consolidation settlement appears to be the primary controlling factor during the monitoring period. This study underscores the potential of InSAR in long-distance water transfer projects and highlights that spatially continuous deformation is the most significant advantage. [ABSTRACT FROM AUTHOR]

Forest stock volume is the main factor to evaluate forest carbon sink level. At present, the combination of multi-source remote sensing and non-parametric models has been widely used in FSV estimation. However, the biodiversity of natural forests is complex, and the response of the spatial information of remote sensing images to FSV is significantly reduced, which seriously affects the accuracy of FSV estimation. To address this challenge, this paper takes China's Baishanzu Forest Park with representative characteristics of natural forests as the research object, integrates the forest survey data, SRTM data, and Landsat 8 images of Baishanzu Forest Park, constructs a time series dataset based on survey time, and establishes an FSV estimation model based on the CNN-LSTM-Attention algorithm. The model uses the convolutional neural network to extract the spatial features of remote sensing images, uses the LSTM to capture the time-varying characteristics of FSV, captures the feature variables with a high response to FSV through the attention mechanism, and finally completes the prediction of FSV. The experimental results show that some features (e.g., texture, elevation, etc.) of the dataset based on multi-source data feature variables are more effective in FSV estimation than spectral features. Compared with the existing models such as MLR and RF, the proposed model achieved higher accuracy in the study area (R2 = 0.8463, rMSE = 26.73 m3/ha, MAE = 16.47 m3/ha). [ABSTRACT FROM AUTHOR]

As a major grain-producing region in China, the North China Plain (NCP) faces serious challenges such as water shortage and land subsidence. In late 2014, the Central Route of the South-to-North Water Diversion Project (SNWD-C) began to provide NCP with water resources. However, the effectiveness of this supply in mitigating land subsidence remains a pivotal and yet unassessed aspect. In this paper, we utilized various geodetic datasets, including the Gravity Recovery and Climate Experiment (GRACE) and GRACE Follow On (GRACE-FO), Global Navigation Satellite System (GNSS) and leveling data, to conduct a spatial-temporal analysis of the equivalent water height (EWH) and vertical ground movement in the NCP. The results reveal a noteworthy decline in EWH from 2011 to 2015, followed by a slight increase with minor fluctuations from 2015 to 2020, demonstrating a strong correlation with the water resources supplied by the SNWD-C. The GRACE-derived surface deformation rate induced by hydrological loading is estimated to be <1 mm/yr. In comparison, GNSS-derived vertical ground movements exhibit considerable regional differences during the 2011–2020 period. Substantial surface subsidence is evident in the central and eastern NCP, contrasting with a gradual uplift in the front plain of the Taihang Mountains. Three-stage leveling results indicate that the rate of subsidence in the central and eastern plains is gradually increasing with the depression area expanding from 1960 to 2010. Based on these geodetic results, it can be inferred that the SNWD-C's operation since 2014 has effectively mitigated the reduction in terrestrial water storage in the NCP. However, land subsidence in the NCP persists, as the subsidence rate does not turn around in sync with the change in EWH following the operation of SNWD-C. Consequently, it's necessary to maintain and enforce existing policies, including controlling groundwater exploitation and water resources supply (e.g., SNWD-C) to curtail the exacerbation of land subsidence in the NCP. Additionally, continuous monitoring of land subsidence by GRACE, GNSS, leveling and other geodetic techniques is crucial to enable timely policy adjustments based on monitoring results. [ABSTRACT FROM AUTHOR]

Landslides are common natural disasters that cause serious damage to ecosystems and human societies. To effectively prevent and mitigate these disasters, an accurate assessment of landslide hazards is necessary. However, most traditional landslide hazard assessment methods rely on static assessment factors while ignoring the dynamic changes in landslides, which may lead to false-positive errors in the assessment results. This paper presents a novel landslide hazard assessment method for the Zagunao River basin, China. In this study, an updated landslide inventory was obtained for the Zagunao River basin using data from interferometric synthetic aperture radar (InSAR) and optical images. Based on this inventory, a landslide susceptibility map was developed using a random forest algorithm. Finally, an evaluation matrix was created by combining the results of deformation rates from both ascending and descending data to establish a hazard level that considers surface deformation. The method presented in this study can reflect recent landslide hazards in the region and produce dynamic assessments of regional landslide hazards. It provides a basis for the government to identify and manage high-risk areas. [ABSTRACT FROM AUTHOR]

Ponds constitute a pivotal component of aquatic ecosystems. The aquatic ecosystem of the Huai River Basin (HRB) in China was once damaged by severe pollution, and numerous ponds in the basin have not been secured. In this paper, Shenqiu County, a typical county in HRB with many ponds, is selected. Based on high-resolution images with ALOS in 2010, GF-2 in 2016, and GF-1 in 2022, we employed discriminant analysis (DA), classification and regression tree, support vector machine, and random forest to extract the ponds based on object-oriented and further analyzed the spatial-temporal variations of the ponds in this county. The results of the DA in these three years exhibited a higher kappa coefficient (>0.7), and overall accuracy (>75%), signifying superior performance when compared to the other three methods. There were 4625, 5315, and 4748 ponds in 2010, 2016, and 2022, with a total area of 12.87, 11.99, and 9.37 km2, respectively. The number of ponds had a trend of rising in the initial period (2010–2016) and falling later (2016–2022), while the total area revealed a continuous decline. Meanwhile, these ponds showed a clustering phenomenon with three main clustering areas, and the scope of the clustering areas also changed to a certain extent from 2010 to 2022. Our study offers valuable methodological support for the ecological monitoring and management of water environments in regions characterized by a dense concentration of ponds. The crucial data related to ponds in this study will help inform both environmental and social development initiatives within the area. [ABSTRACT FROM AUTHOR]