Search

We propose and implement an optical technique to access the local temperature of an erbium doped crystal by probing the electron spin population under magnetic field. We reliably extract the sample temperature in the range 2–7 K. We additionally discuss the suitability of our method as a primary standard for cryogenic thermometry. By adding an auxiliary heating laser, we are able to measure the interface conductance between the dielectric crystal and the cold plate of the cryostat by exploring different cooling configurations. [ABSTRACT FROM AUTHOR]

Ultracold atoms exquisitely controlled by lasers are the quantum foundation, particularly for sensing, timekeeping, and computing, of state-of-the-art quantum science and technology. However, the laboratory-scale infrastructure for such optical-atomic quantum apparatus rarely translates into commercial applications. A promising solution is miniaturizing the optical layouts onto a chip-scale device integrated with cold atoms inside a compact ultra-high vacuum (UHV) chamber. For prototyping purposes, however, rapidly loading or exchanging test photonic devices into a UHV chamber is limited by the evacuation time from atmospheric pressures to the optimal pressures for ultracold atoms of 1 × 10−11 Torr, a process that typically takes weeks or months without cryogenics. Here, we present a loadlock apparatus and loading procedure capable of venting, exchanging, and evacuating back to < 1 × 1 0 − 11 Torr in under 24 h. Our system allows for rapid testing and benchmarking of various photonic devices with ultracold atoms. [ABSTRACT FROM AUTHOR]

We report the development of a continuous-wave and pulsed X-band electron spin resonance (ESR) spectrometer for the study of spins on ordered surfaces down to cryogenic temperatures. The spectrometer operates in ultra-high vacuum and utilizes a half-wavelength microstrip line resonator realized using epitaxially grown copper films on single crystal Al2O3 substrates. The one-dimensional microstrip line resonator exhibits a quality factor of more than 200 at room temperature, close to the upper limit determined by radiation losses. The surface characterizations of the copper strip of the resonator by atomic force microscopy, low-energy electron diffraction, and scanning tunneling microscopy show that the surface is atomically clean, flat, and single crystalline. Measuring the ESR spectrum at 15 K from a few nm thick molecular film of YPc2, we find a continuous-wave ESR sensitivity of 2.6 × 1011 spins/G · Hz1/2, indicating that a signal-to-noise ratio of 3.9 G · Hz1/2 is expected from a monolayer of YPc2 molecules. Advanced pulsed ESR experimental capabilities, including dynamical decoupling and electron-nuclear double resonance, are demonstrated using free radicals diluted in a glassy matrix. [ABSTRACT FROM AUTHOR]

Nanoscale thermal imaging and temperature detection are of fundamental importance in diverse scientific and technological realms. Most nanoscale thermometry techniques focus on probing the temperature of lattice or phonons and are insensitive to nonequilibrium electrons, commonly referred to as "hot electrons." While terahertz scanning noise microscopy (SNoiM) has been demonstrated to be powerful in the thermal imaging of hot electrons, prior studies have been limited to room temperature. In this work, we report the development of a cryogenic SNoiM (Cryo-SNoiM) tailored for quantitative hot electron temperature detection at low temperatures. The microscope features a special two-chamber design where the sensitive terahertz detector, housed in a vacuum chamber, is efficiently cooled to ∼5 K using a pulse tube cryocooler. In a separate chamber, the atomic force microscope and the sample can be maintained at room temperature under ambient/vacuum conditions or cooled to ∼110 K via liquid nitrogen. This unique dual-chamber cooling system design enhances the efficacy of SNoiM measurements at low temperatures. It not only facilitates the pre-selection of tips at room temperature before cooling but also enables the quantitative derivation of local electron temperature without reliance on any adjustable parameters. The performance of Cryo-SNoiM is demonstrated through imaging the distribution of hot electrons in a cold, self-heated narrow metal wire. This instrumental innovation holds great promise for applications in imaging low-temperature hot electron dynamics and nonequilibrium transport phenomena across various material systems. [ABSTRACT FROM AUTHOR]

We describe the design principles, fabrication, and characterization of a precision AC resonant capacitance bridge (RCB) sensor, based on a resonant differential planar printed circuit board transformer with a solid (ungapped) MnZn ferrite core, demonstrating a short-term sensitivity at 293 K of 0.225 ± 0.005 aF/√Hz at around 120 kHz resonance frequency and 1 Hz Fourier measurement frequency. At 120 K, the RCB short term noise sensitivity is 0.118 ± 0.005 aF/√Hz. We compare the ungapped configuration to five different RCBs: three with a core gap of 65 μm and two with a core gap of 130 μm. Their average room temperature short term noise sensitivities are 0.30 ± 0.01 and 0.45 ± 0.01 aF/√Hz, while the cryogenic operation of these transformers at 120 K resulted in averaged sensitivities of 0.23 ± 0.01 and 0.36 ± 0.01 aF/√Hz, respectively. Multi-hour room temperature runs, with one core of each of the three gap types, proved the stability of their long-term sensitivities of 0.234 ± 0.005, 0.338 ± 0.009, and 0.435 ± 0.010 aF/√Hz for the ungapped (40-h duration) and the 65 and 130 μm (28-h duration) cores, respectively. At 0.1 mHz, a critical frequency for space gravitational wave detectors, the respective sensitivities are 0.25 ± 0.02, 0.35 ± 0.02, and 0.53 ± 0.07 aF/√Hz. Measurements with the ungapped transformer configuration for temperatures from 325 to 349 K further validate the dependence of the noise model on temperature and permeability. The performance of our RCB with an ungapped core matches the calculated performance value and shows an improvement in signal-to-noise ratio of two or more compared with capacitance bridges developed for similar applications. A further factor of about two noise reductions is achieved by cooling to 120 K. [ABSTRACT FROM AUTHOR]

In 2014, we introduced a new experimental approach to study the UV photo-processing of cryogenic ices of astrophysical interest using laser ablation in a combination of ionization and time-of-flight mass spectrometry (ToF-MS). The setup, Mass Analytical Tool to Research Interstellar ICES, allowed us to detect newly formed species at low abundances. However, we found that with the increase in molecular complexity over the years, the detection of larger photoproducts was hindered by the dynamic range of detectors used. Here, we introduce a method to overcome this issue that we expect to be useful for similar applications in other research fields. The concept is based on a precisely controlled high-energy pulser that regulates the voltage across the deflection plates of the ToF-MS instrument to deflect the most abundant species and prevent them from reaching the detector. In this way, the detector sensitivity can be increased from an operating voltage of 2500 V up to 3000 V. The applicability is first illustrated in the simple case of an argon matrix, where 40Ar+ ions are deflected to increase the detection sensitivity for 40Ar2+ at m/z = 20 and 40 A r 2 + at m/z = 80 by a factor 30. Similarly, it is shown that substantially larger complex organic molecules, an important species in astrochemical reaction networks, can be measured for UV irradiated methanol ice. [ABSTRACT FROM AUTHOR]

We present the requirements, design, and evaluation of the cryogenic continuously rotating half-wave plate (CHWP) for the Simons Observatory (SO). SO is a cosmic microwave background polarization experiment at Parque Astronómico de Atacama in northern Chile that covers a wide range of angular scales using both small (⌀ 0.42 m) and large (⌀ 6 m) aperture telescopes. In particular, the small aperture telescopes (SATs) focus on large angular scales for primordial B-mode polarization. To this end, the SATs employ a CHWP to modulate the polarization of the incident light at 8 Hz, suppressing atmospheric 1/f noise and mitigating systematic uncertainties that would otherwise arise due to the differential response of detectors sensitive to orthogonal polarizations. The CHWP consists of a 505 mm diameter achromatic sapphire HWP and a cryogenic rotation mechanism, both of which are cooled down to ∼50 K to reduce detector thermal loading. Under normal operation, the HWP is suspended by a superconducting magnetic bearing and rotates with a constant 2 Hz frequency, controlled by an electromagnetic synchronous motor. We find that the number of superconductors and the number of magnets that make up the superconducting magnetic bearing are important design parameters, especially for the rotation mechanism's vibration performance. The rotation angle is detected through an angular encoder with a noise level of 0.07 μrad s . During a cooldown process, the rotor is held in place by a grip-and-release mechanism that serves as both an alignment device and a thermal path. In this paper, we provide an overview of the SO SAT CHWP: its requirements, hardware design, and laboratory performance. [ABSTRACT FROM AUTHOR]

We have conceived, built, and operated a cryogenic vacuum valve with opening and closing times as short as 50 ms that can be used in strong magnetic fields and across a broad range of duty cycles. It is used to seal a cryogenic Penning trap at liquid-helium temperature for long-term storage of highly charged ions in a vacuum better than 10−15 hPa from a room-temperature ion beamline at vacuum conditions around 10−9 hPa. It will significantly improve any experiment where a volume at the most extreme vacuum conditions must be temporarily connected to a less demanding vacuum during repeated experimental cycles. We describe the design of this valve and show measurements that characterize its main features. [ABSTRACT FROM AUTHOR]

Currently, the world's only source of low-energy antiprotons is the AD/ELENA facility located at CERN. To date, all precision measurements on single antiprotons have been conducted at this facility and provide stringent tests of fundamental interactions and their symmetries. However, magnetic field fluctuations from the facility operation limit the precision of upcoming measurements. To overcome this limitation, we have designed the transportable antiproton trap system BASE-STEP to relocate antiprotons to laboratories with a calm magnetic environment. We anticipate that the transportable antiproton trap will facilitate enhanced tests of charge, parity, and time-reversal invariance with antiprotons and provide new experimental possibilities of using transported antiprotons and other accelerator-produced exotic ions. We present here the technical design of the transportable trap system. This includes the transportable superconducting magnet, the cryogenic inlay consisting of the trap stack and detection systems, and the differential pumping section to suppress the residual gas flow into the cryogenic trap chamber. [ABSTRACT FROM AUTHOR]

We sympathetically cool highly charged ions (HCI) in Coulomb crystals of Doppler-cooled Be+ ions confined in a cryogenic linear Paul trap that is integrated into a fully enclosing radio-frequency resonator manufactured from superconducting niobium. By preparing a single Be+ cooling ion and a single HCI, quantum logic spectroscopy toward frequency metrology and qubit operations with a great variety of species are enabled. While cooling down the assembly through its transition temperature into the superconducting state, an applied quantization magnetic field becomes persistent, and the trap becomes shielded from subsequent external electromagnetic fluctuations. Using a magnetically sensitive hyperfine transition of Be+ as a qubit, we measure the fractional decay rate of the stored magnetic field to be at the 10−10 s−1 level. Ramsey interferometry and spin-echo measurements yield coherence times of >400 ms, demonstrating excellent passive magnetic shielding at frequencies down to DC. [ABSTRACT FROM AUTHOR]

We report on an ion trapping system for performing a novel form of cryogenic messenger spectroscopy with single molecule sensitivity. The system features a cryogenic radio-frequency ion trap loaded with single analyte molecules via a quadrupole mass filter. We demonstrate the ability to controllably attach inert gas particles to buffer gas cooled, trapped molecular ions. Sympathetic cooling by co-trapped, laser cooled 88Sr+ further reduces the translational temperature of trapped molecules to the millikelvin regime. We verify the presence of cryogenic "tags" via non-destructive optical mass spectrometry and selectively remove these adducts by resonantly driving vibrational transitions in the tagged molecular ions. This enables us to derive the vibrational spectrum of a single analyte molecule from the frequency dependence of the tag detachment rate. We have demonstrated these capabilities by measuring transitions in the C–H stretching region for single cationic fragments of both indole (C8H7N) and 1,3-benzodioxole (C6H4O2CH2). These capabilities are not reliant on a specific molecular level structure and thus constitute a general, non-destructive method for vibrational spectroscopy of individual molecular ions. [ABSTRACT FROM AUTHOR]

In this contribution, we present an efficient and alternative method to the commonly used RF-multipole trap technique to produce He-tagged molecular ions at cryogenic temperatures, which are perfectly suitable for messenger spectroscopy. The seeding of dopant ions in multiply charged helium nanodroplets, in combination with a gentle extraction of the latter from the helium matrix, enables the efficient production of He-tagged ion species. With a quadrupole mass filter, a specific ion of interest is selected, merged with a laser beam, and the photoproducts are measured in a time-of-flight mass-spectrometer. The detection of the photofragment signal from a basically zero background is much more sensitive than the depletion of the same amount of signal from precursor ions, delivering high quality spectra at reduced data acquisition times. Proof-of-principle measurements of bare and He-tagged Ar-cluster ions, as well as of He-tagged C60 ions, are presented. [ABSTRACT FROM AUTHOR]

We report calibrated microwave transmission and reflection measurements of a qubit sample holder at millikelvin temperatures. The methodology we present extends our previous work on one-port cryogenic short–open–load (SOL) calibration to a two-port SOLT measurement by implementing an unknown thru (T) standard. We report the resulting calibrated transmission and reflection at millikelvin temperatures through a printed circuit board that is installed into the sample holder. Finally, we consider a cascade of components at the end of a qubit drive line that includes (1) a cryogenic attenuator, (2) a coaxial cable, and (3) a qubit sample holder. Using experimentally determined parameters for return losses for all three components, we calculate the negligible state-preparation error in the frequency band of 5–7 GHz due to control pulse distortions arising from reflection at the coaxial launches. Taken together, our results highlight the utility of calibrated cryogenic scattering parameter measurements for the validation of qubit packaging and the wiring in its immediate vicinity. [ABSTRACT FROM AUTHOR]

Cryogenic scanning tunneling microscopy and spectroscopy (STM/STS) performed in a high vector magnetic field provide unique possibilities for imaging surface magnetic structures and anisotropic superconductivity and exploring spin physics in quantum materials with atomic precision. Here, we describe the design, construction, and performance of a low-temperature, ultra-high-vacuum (UHV) spectroscopic-imaging STM equipped with a vector magnet capable of applying a field of up to 3 T in any direction with respect to the sample surface. The STM head is housed in a fully bakeable UHV compatible cryogenic insert and is operational over variable temperatures ranging from ∼ 300 down to 1.5 K. The insert can be easily upgraded using our home-designed 3He refrigerator. In addition to layered compounds, which can be cleaved at a temperature of either ∼ 300 , ∼ 77 , or ∼ 4.2 K to expose an atomically flat surface, thin films can also be studied by directly transferring using a UHV suitcase from our oxide thin-film laboratory. Samples can be treated further with a heater and a liquid helium/nitrogen cooling stage on a three-axis manipulator. The STM tips can be treated in vacuo by e-beam bombardment and ion sputtering. We demonstrate the successful operation of the STM with varying the magnetic field direction. Our facility provides a way to study materials in which magnetic anisotropy is a key factor in determining the electronic properties such as in topological semimetals and superconductors. [ABSTRACT FROM AUTHOR]

A combination of direct current (DC) fields and high amplitude radio frequency (RF) fields is necessary to trap ions in a Paul trap. Such high electric RF fields are usually reached with the help of a resonator in close proximity to the ion trap. Ion trap based quantum computers profit from good vacuum conditions and low heating rates that cryogenic environments provide. However, an impedance matching network between the resonator and its RF source is necessary, as an unmatched resonator would require higher input power due to power reflection. The reflected power would not contribute to the RF trapping potential, and the losses in the cable induce additional heat into the system. The electrical properties of the matching network components change during cooling, and a cryogenic setup usually prohibits physical access to integrated components while the experiment is running. This circumstance leads to either several cooling cycles to improve the matching at cryogenic temperatures or the operation of poorly matched resonators. In this work, we demonstrate an RF resonator that is actively matched to the wave impedance of coaxial cables and the signal source. The active part of the matching circuit consists of a varactor diode array. Its capacitance depends on the DC voltage applied from outside the cryostat. We present measurements of the power reflection, the Q-factor, and higher harmonic signals resulting from the nonlinearity of the varactor diodes. The RF resonator is tested in a cryostat at room temperature and cryogenic temperatures, down to 4.3 K. A superior impedance matching for different ion traps can be achieved with this type of resonator. [ABSTRACT FROM AUTHOR]

Cryogenic vector magnet systems make it possible to study the anisotropic magnetic properties of materials without mechanically rotating the sample but by electrically tilting and turning the magnetic field. Vector magnetic fields generated inside superconducting vector magnets are generally measured with three Hall sensors. These three probes must be calibrated over a range of temperatures, and the temperature-dependent calibrations cannot be easily carried out inside an already magnetized superconducting magnet because of remaining magnetic fields. A single magnetometer based on an ensemble of nitrogen vacancy (NV) centers in diamond is proposed to overcome these limitations. The quenching of the photoluminescence intensity emitted by NV centers can determine the field in the remanent state of the solenoids and allows an easy and fast canceling of the residual magnetic field. Once the field is reset to zero, the calibration of this magnetometer can be performed in situ by a single measurement of an optically detected magnetic resonance spectrum. Thereby, these magnetometers do not require any additional temperature-dependent calibrations outside the magnet and offer the possibility to measure vector magnetic fields in three dimensions with a single sensor. Its axial alignment is given by the crystal structure of the diamond host, which increases the accuracy of the field orientation measured with this sensor, compared to the classical arrangement of three Hall sensors. It is foreseeable that the magnetometer described here has the potential to be applied in various fields in the future, such as the characterization of ferromagnetic core solenoids or other magnetic arrangements. [ABSTRACT FROM AUTHOR]

Kinetic inductance bolometer technology is a candidate for passive submillimeter wave and terahertz imaging systems. Its benefits include scalability into large 2D arrays and operation with intermediate cryogenics in the temperature range of 5–10 K. We have previously demonstrated the scalability in terms of device fabrication, optics integration, and cryogenics. In this article, we address the last missing ingredient, the readout. The concept, serial addressed frequency excitation, is an alternative to full frequency-division multiplexing at microwave frequencies conventionally used to read out kinetic inductance detectors. We introduce the concept and analyze the criteria of the multiplexed readout avoiding the degradation of the signal-to-noise ratio in the presence of a thermal anti-alias filter inherent to thermal detectors. We present a practical scalable realization of a readout system integrated into a prototype imager with 8712 detectors. This is used for demonstrating the noise properties of the readout. Furthermore, we present practical detection experiments with a stand-off laboratory-scale imager. [ABSTRACT FROM AUTHOR]

We describe an instrument which can be used to analyze complex chemical mixtures at high resolution and high sensitivity. Molecules are collisionally cooled with helium gas at cryogenic temperatures (∼4–7 K) and subsequently detected using chirped pulse microwave spectroscopy. Here, we demonstrate three significant improvements to the apparatus relative to an earlier version: (1) extension of its operating range by more than a factor of two, from 12–18 GHz to 12–26 GHz, which allows a much wider range of species to be characterized; (2) improved detection sensitivity owing to the use of cryogenically cooled low-noise amplifiers and protection switches; and (3) a versatile method of sample input that enables analysis of solids, liquids, gases, and solutions, without the need for chemical separation (as demonstrated with a 12–16 GHz spectrum of lemon oil). This instrument can record broadband microwave spectra at comparable sensitivity to high Q cavity spectrometers which use pulsed supersonic jets, but up to 3000 times faster with a modest increase in the sample consumption rate. [ABSTRACT FROM AUTHOR]

Based upon a superconducting transition edge sensor (TES), the Meissner-TES is a relatively new type of high resolution cryogenic thermometer which employs the magnetic transition of a superconductor to measure temperature. We have improved the signal-to-noise for DC sensing by a factor of 30 compared to our prior effort and developed a new AC mode which uses an oscillating magnetic field and a lock-in technique with much lower magnetic noise than the DC mode. The thermometer was tuned in situ over a range of operating temperatures 10–50 times larger than the transition width of the superconductor, using an applied persistent magnetic field. The DC mode can have sensitivity better than 1 nK for 100 s averaging, and the AC mode has sensitivity better than 120 nK for very small applied magnetic fields near 14 nT and 100 s averaging. The Meissner-TES can be applied to high sensitivity infrared sensing, optical power scale realization, and the study of temperature-dependent phase transitions. [ABSTRACT FROM AUTHOR]

A modularized cryogenic indentation apparatus was designed and created to study the deformation mechanisms and mechanical properties of materials at low temperatures. The indentation process is actuated by piezoelectric stack and flexure hinge, and the entire mechanical module is kept inside the vacuum chamber to prevent the occurrence of ice. Numerous issues including the effects of the application of cooling module and processes to diminish the temperature effect on the indentation tip were addressed. Several influential factors during temperature indentation were discussed. Tests on calibration specimen demonstrated the feasibility of the apparatus. Monocrystalline silicon and copper were tested using the current apparatus at temperatures ranging from room temperature to 150 K to show its main functions and usability. [ABSTRACT FROM AUTHOR]

We present the design and implementation of a mechanical low-pass filter vibration isolation used to reduce the vibrational noise in a cryogen-free dilution refrigerator operated at 10 mK, intended for scanning probe techniques. We discuss the design guidelines necessary to meet the competing requirements of having a low mechanical stiffness in combination with a high thermal conductance. We demonstrate the effectiveness of our approach by measuring the vibrational noise levels of an ultrasoft mechanical resonator positioned above a superconducting quantum interference device. Starting from a cryostat base temperature of 8 mK, the vibration isolation can be cooled to 10.5 mK, with a cooling power of 113 µW at 100 mK. We use the low vibrations and low temperature to demonstrate an effective cantilever temperature of less than 20 mK. This results in a force sensitivity of less than 500 zN/ Hz and an integrated frequency noise as low as 0.4 mHz in a 1 Hz measurement bandwidth. [ABSTRACT FROM AUTHOR]

A cryogenic cylindrical ion trap velocity map imaging spectrometer has been developed to study photodissociation spectroscopy and dynamics of gaseous molecular ions and ionic complexes. A cylindrical ion trap made of oxygen-free copper is cryogenically cooled down to ∼7 K by using a closed cycle helium refrigerator and is coupled to a velocity map imaging (VMI) spectrometer. The cold trap is used to cool down the internal temperature of mass selected ions and to reduce the velocity spread of ions after extraction from the trap. For CO2+ ions, a rotational temperature of ∼12 K is estimated from the recorded [1 + 1] two-photon dissociation spectrum, and populations in spin-orbit excited X2Πg,1/2 and vibrationally excited states of CO2+ are found to be non-detectable, indicating an efficient internal cooling of the trapped ions. Based on the time-of-flight peak profile and the image of N3+, the velocity spread of the ions extracted from the trap, both radially and axially, is interpreted as approximately ±25 m/s. An experimental image of fragmented Ar+ from 307 nm photodissociation of Ar2+ shows that, benefitting from the well-confined velocity spread of the cold Ar2+ ions, a VMI resolution of Δv/v ∼ 2.2% has been obtained. The current instrument resolution is mainly limited by the residual radial speed spread of the parent ions after extraction from the trap. [ABSTRACT FROM AUTHOR]

Electron spin resonance (ESR) spectroscopy of paramagnetic species in single crystals is a powerful tool for characterizing the latter's magnetic interaction parameters in detail. Conventional ESR systems are optimized for millimeter-size samples and make use of cavities and resonators that accommodate tubes and capillaries in the range 1-5 mm. Unfortunately, in the case of many interesting materials such as enzymes and inorganic catalytic materials (e.g., zeolites), single crystals can only be obtained in micron-scale sizes (1-200 µm). To boost ESR sensitivity and to enable experiments on microcrystals, the ESR resonator needs to be adapted to the size and shape of these specific samples. Here, we present a unique family of miniature surface resonators, known as "ParPar" resonators, whose mode volume and shape are optimized for such micron-scale single crystals. This approach significantly improves upon the samples' filling factor and thus enables the measurement of much smaller crystals than was previously possible. We present here the design of such resonators with a typical mode dimension of 20-50 µm, as well as details about their fabrication and testing methods. The devices' resonant mode(s) are characterized by ESR microimaging and compared to the theoretical calculations. Moreover, experimental ESR spectra of single microcrystals with typical sizes of ∼25-50 µm are presented. The measured spin sensitivity for the 50-µm resonator at cryogenic temperatures of 50 K is found to be ∼1.8 × 106 spins/G √Hz for a Cu-doped single crystal sample that is representative of many biological samples of relevance. [ABSTRACT FROM AUTHOR]

A friction setup combining real-time ice-rubber contact visualization, force measurement, and a compact controlled cold environment system was developed in order to investigate ice-rubber contact complex tribological response and the various contributions to friction, such as viscoelastic deformation, ice surface melting, adhesion, ice creep, or quasi-liquid layer effect. The cold system was based on a cryogenic bath circulator, an air convection circuit, and several thermal insulation combinations such as silica aerogel and expanded polystyrene. The KŌRI tribometer allows one to reach negative temperatures until −20 °C and to perform tribological experiments for velocity from 50 μm s−1 to 1 m s−1 under load up to 50 N and to simultaneously measure resultant forces until 30 N and visualize the contact in real-time. In parallel, an ice manufacturing unit and a specific protocol were developed to grow a transparent ice disc with a controlled initial roughness and surface state. Real-time and simultaneous visualization of the ice-rubber contact provides additional data, such as the apparent contact area and the mean size of a real contact spot during friction, after adequate and dedicated image processing. To illustrate the capability of the KŌRI tribometer, rubber-ice friction measurements were performed at −10 °C and the results are presented here, as a function of time and velocity. [ABSTRACT FROM AUTHOR]

We report on a cryogenic scanning tunneling microscope (STM) designed for single molecule studies, in which the light emitted from the tunneling junction is collected by an integrated optics on the tip. Using direct laser writing, the tip and the surrounding microscopic parabolic mirror are fabricated as one piece, which is small enough to collimate the collected light directly into an optical multimode fiber fixed inside the STM. This simple and compact setup combines high collection efficiency and ease of handling while not interfering with the cryostat operation, allowing uninterrupted measurements at 1.4 K for up to 5 days with low drift. [ABSTRACT FROM AUTHOR]

Multipole radio-frequency (RF) traps are central to collisional experiments in cryogenic environments. They also offer possibilities to generate new type of ion crystals topologies and in particular the potential to create infinite 1D/2D structures: ion rings and ion tubes. However, multipole traps have also been shown to be very sensitive to geometrical misalignment of the trap rods, leading to additional local trapping minima. The present work proposes a method to correct non-ideal potentials, by modifying the applied RF amplitudes for each trap rod. This approach is discussed for the octupole trap, leading to the restitution of the ideal Mexican-Hat-like pseudo-potential, expected in multipole traps. The goodness of the compensation method is quantified in terms of the choice of the diagnosis area, the residual trapping potential variations, the required adaptation of the applied RF voltage amplitudes, and the impact on the trapped ion structures. Experimental implementation for macroscopic multipole traps is also discussed, in order to propose a diagnostic method with respect to the resolution and stability of the trap drive. Using the proposed compensation technique, we discuss the feasibility of generating a homogeneous ion ring crystal, which is a measure of quality for the obtained potential well. [ABSTRACT FROM AUTHOR]

Neutrinoless double beta decay (0νββ) is a direct probe of physics beyond the standard model. Its discovery would demonstrate that the lepton number is not a symmetry of nature and would provide us with unique information on the nature and mass of the neutrinos. Among the experimental techniques employed in the investigation of this rare process, thermal detectors fulfill the requirements for a powerful search, showing an excellent energy resolution and the possibility of scaling to very large masses. In this work, we review the long chain of bolometric experiments based on TeO2 crystals that were and continue to be carried out at the Laboratori Nazionali del Gran Sasso (Italy), searching for 0νββ of 130Te. We illustrate the progress and improvements achieved in almost thirty years of measurements and compare the various performance and results. We describe the several steps that led to the CUORE detector, the latest of this series and presently in data taking, and we highlight the challenges that a next bolometric experiment will face in order to further improve the sensitivity, especially concerning the background abatement. Finally, we emphasize the advantages of 130Te in the search for 0νββ with a further future experiment. [ABSTRACT FROM AUTHOR]

A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz. [ABSTRACT FROM AUTHOR]

Long-term changes in the responsivity of unbiased silicon photodiodes were observed when operating at the temperature of 90 K. The change manifested as a monotonic increase in current output for a fixed optical power input. The current output has been observed to increase by 20% or more relative to room-temperature output. In all trials, the effect was fully reversed upon returning to room temperature. Analysis of spectrally resolved data showed that the effect is due to formation of a contaminant thin film, of as-yet-unknown composition. [ABSTRACT FROM AUTHOR]

A new cryogenic linear ion trap beamline has been constructed and commissioned, which serves to inject cold molecular and cluster ions into the RIKEN cryogenic electrostatic ring (RICE). Ions are created with an electrospray ion source, and a quadrupole mass filter is used for mass-selection prior to trap injection. The radio frequency octupole ion trap can be continuously loaded with ions and features a fast ion extraction mode to create short ion bunches with tens of μs duration. We report here on the simulations and development of the ion trap beamline and validate performance with the moderately heavy molecular cation methylene blue. Characterization of the novel trap design with additional wedge-shaped electrodes was carried out, which includes the determination of the temporal and spatial shape of the ion bunch and the total number of ions after extraction. Finally, these ion bunches are synchronized with the switching of a pulsed high-voltage acceleration device downstream of the trap, where the ions obtain a kinetic energy of up to 20 keV. The preparation and control of the keV ion beam are demonstrated for the ion injection into RICE. [ABSTRACT FROM AUTHOR]

We present the construction and performance of an ultra-low-temperature scanning tunneling microscope (STM), working in ultra-high vacuum (UHV) conditions and in high magnetic fields up to 9 T. The cryogenic environment of the STM is generated by a single-shot 3He magnet cryostat in combination with a 4He dewar system. At a base temperature (300 mK), the cryostat has an operation time of approximately 80 h. The special design of the microscope allows the transfer of the STM head from the cryostat to a UHV chamber system, where samples and STM tips can be easily exchanged. The UHV chambers are equipped with specific surface science treatment tools for the functionalization of samples and tips, including high-temperature treatments and thin film deposition. This, in particular, enables spin-resolved tunneling measurements. We present test measurements using well-known samples and tips based on superconductors and metallic materials such as LiFeAs, Nb, Fe, and W. The measurements demonstrate the outstanding performance of the STM with high spatial and energy resolution as well as the spin-resolved capability. [ABSTRACT FROM AUTHOR]

The superconducting nanowire single-photon detector (SNSPD) is a leading technology for quantum information science applications using photons, and is finding increasing uses in photon-starved classical imaging applications. Critical detector characteristics, such as timing resolution (jitter), reset time, and maximum count rate, are heavily influenced by the readout electronics that sense and amplify the photon detection signal. We describe a readout circuit for SNSPDs using commercial off-the-shelf amplifiers operating at cryogenic temperatures. Our design demonstrates a 35 ps timing resolution and a maximum count rate of over 2 × 107 counts per second, while maintaining <3 mW power consumption per channel, making it suitable for a multichannel readout. [ABSTRACT FROM AUTHOR]

A cryogenic stationary afterglow apparatus equipped with a near-infrared cavity-ring-down-spectrometer (Cryo-SA-CRDS) for studies of electron-ion recombination processes in the plasma at temperatures 30-300 K has been designed, constructed, tested, and put into operation. The plasma is generated in a sapphire discharge tube that is contained in a microwave cavity. The cavity and the tube are attached to the second stage of the cold head of the cryocooler system, and they are inserted to an UHV chamber with mirrors for CRDS and vacuum windows on both ends of the tube. The temperature of the discharge tube can be made as low as 25 K. In initial test measurements, the discharge was ignited in He/Ar/H2 or He/H2 gas mixtures and the density of H 3 + ions and their kinetic and rotational temperatures were measured during the discharge and afterglow. From the measured decrease in the ion density, during the afterglow, effective recombination rate coefficients were determined. Plasma relaxation was studied in He/Ar gas mixtures by monitoring the presence of highly excited argon atoms. The spectroscopic measurements demonstrated that the kinetic temperature of the ions is equal to the gas temperature and that it can be varied from 300 K down to 30 K. [ABSTRACT FROM AUTHOR]

An efficient loading technique has been developed for flammable, toxic, or explosive gases which can be condensed at liquid nitrogen temperature and ambient pressure in membrane diamond anvil cells (DACs). This cryogenic technique consists in a deposition of small quantities of the desired gas directly into the sample chamber. The deposition is performed using a capillary that reaches the space between the diamond anvils. The DAC is kept under inert gas overpressure during the whole process, in order to avoid contamination from atmospheric O2, CO2, and H2O. This technique provides significant advantages over standard cryo-loading and gas-loading when the condensation of dangerous samples at liquid nitrogen temperature raises safety concerns because it allows dealing with minimum quantities of condensed gases. The whole procedure is particularly fast and efficient. The “spray-loading” has been successfully used in our laboratory to load several samples including acetylene, ammonia, ethylene, and carbon dioxide/water or red phosphorus/NH3 mixtures. [ABSTRACT FROM AUTHOR]

We have conceived, built, and operated a cryogenic Penning trap with an electrically conducting yet optically transparent solid electrode. The trap, dedicated to spectroscopy and imaging of confined particles under large solid angles, is of "half-open" design with one open endcap and one closed endcap that mainly consists of a glass window coated with a highly transparent conductive layer. This arrangement allows for the trapping of externally or internally produced particles and yields flexible access for optical excitation and efficient light collection from the trapping region. At the same time, it is electrically closed and ensures long-term ion confinement under well-defined conditions. With its superior surface quality and its high as well as homogeneous optical transmission, the window electrode is an excellent replacement for partially transmissive electrodes that use holes, slits, metallic meshes, and the like. [ABSTRACT FROM AUTHOR]

The cross-spectrum noise measurement technique enables enhanced resolution of spectral measurements. However, it has disadvantages, namely, increased complexity, inability of making real-time measurements, and bias due to the “cross-spectral collapse” (CSC) effect. The CSC can occur when the spectral density of a random process under investigation approaches the thermal noise of the power splitter. This effect can severely bias results due to a differential measurement between the investigated noise and the anti-correlated (phase-inverted) noise of the power splitter. In this paper, we report an accurate measurement of the phase noise of a thermally limited electronic oscillator operating at room temperature (300 K) without significant CSC bias. We mitigated the problem by cooling the power splitter to liquid helium temperature (4 K).We quantify errors of greater than 1 dB that occur when the thermal noise of the oscillator at room temperature is measured with the power splitter at temperatures above 77 K. [ABSTRACT FROM AUTHOR]

Low-temperature electronic transport measurements with high energy resolution require both effective low-pass filtering of high-frequency input noise and an optimized thermalization of the electronic system of the experiment. In recent years, elaborate filter designs have been developed for cryogenic low-level measurements, driven by the growing interest in fundamental quantum-physical phenomena at energy scales corresponding to temperatures in the few millikelvin regime. However, a single filter concept is often insufficient to thermalize the electronic system to the cryogenic bath and eliminate spurious high frequency noise. Moreover, the available concepts often provide inadequate filtering to operate at temperatures below 10 mK, which are routinely available now in dilution cryogenic systems. Herein we provide a comprehensive analysis of commonly used filter types, introduce a novel compact filter type based on ferrite compounds optimized for the frequency range above 20 GHz, and develop an improved filtering scheme providing adaptable broad-band low-pass characteristic for cryogenic low-level and quantum measurement applications at temperatures down to few millikelvin. [ABSTRACT FROM AUTHOR]

Lowenergy threshold detectors are necessary in many frontier fields of the experimental physics. In this work, we present a novel detection approach based on pure or doped matrices of inert gases solidified at cryogenic temperatures. The small energy release of the incident particle can be transferred directly (in pure crystals) or through a laser-driven ionization (in doped materials) to the electrons of the medium that are then converted into free electrons. The charge collection process of the electrons that consists in their drift within the crystal and their extraction through the solid–vacuum interface gives rise to an electric signal that we exploit for preliminary tests of charge collection and crystal quality. Such tests are carried out in different matrices of neon and methane using an UV-assisted apparatus for electron injection in crystals. [ABSTRACT FROM AUTHOR]

We describe the design, fabrication, and validation of a cryogenically compatible quasioptical thermal source for characterization of detector arrays. The source is constructed using a graphite-loaded epoxy mixture that is molded into a tiled pyramidal structure. The mold is fabricated using a hardened steel template produced via a wire electron discharge machining process. The absorptive mixture is bonded to a copper backplate enabling thermalization of the entire structure and measurement of the source temperature. Measurements indicate that the reflectance of the source is <0.001 across a spectral band extending from 75 to 330 GHz. [ABSTRACT FROM AUTHOR]

We present the design and construction of an NMR probe to investigate single crystals under strain at cryogenic temperatures. The probe head incorporates a piezoelectric-based apparatus from Razorbill Instruments that enables both compressive and tensile strain tuning up to strain values on the order of 0.3% with a precision of 0.001%. 75As NMR in BaFe2As2 reveals large changes to the electric field gradient and indicates that the strain is homogeneous to within 16% over the volume of the NMR coil. [ABSTRACT FROM AUTHOR]

Spin-polarized scanning tunneling microscopy (SP-STM) performed in vector magnetic fields promises atomic scale imaging of magnetic structure, providing complete information on the local spin texture of a sample in three dimensions. Here, we have designed and constructed a turntable system for a low temperature STM which in combination with a 2D vector magnet provides magnetic fields of up to 5 T in any direction relative to the tip-sample geometry. This enables STM imaging and spectroscopy to be performed at the same atomic-scale location and field-of-view on the sample, and most importantly, without experiencing any change on the tip apex before and after field switching. Combined with a ferromagnetic tip, this enables us to study the magnetization of complex magnetic orders in all three spatial directions. [ABSTRACT FROM AUTHOR]

A 16-image Kirkpatrick–Baez (KB)–type x-ray microscope consisting of compact KB mirrors [F. J. Marshall, Rev. Sci. Instrum. 83, 10E518 (2012)] has been assembled for the first time with mirrors aligned to allow it to be coupled to a high-speed framing camera. The high-speed framing camera has four independently gated strips whose emission sampling interval is ~30 ps. Images are arranged four to a strip with ~60-ps temporal spacing between frames on a strip. By spacing the timing of the strips, a frame spacing of ~15 ps is achieved. A framed resolution of ~6-μm is achieved with this combination in a 400-μm region of laser-plasma x-ray emission in the 2- to 8-keV energy range. A principal use of the microscope is to measure the evolution of the implosion stagnation region of cryogenic DT target implosions on the University of Rochester’s OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. The unprecedented time and spatial resolutions achieved with this framed, multi-image KB microscope have made it possible to accurately determine the cryogenic implosion core emission size and shape at the peak of stagnation. These core size measurements, taken in combination with those of ion temperature, neutron-production temporal width, and neutron yield allow for inference of core pressures, currently exceeding 50 Gbar in OMEGA cryogenic target implosions [Regan et al., Phys. Rev. Lett. 117, 025001 (2016)]. [ABSTRACT FROM AUTHOR]

A technique for the creation of free-standing cryogenic targets for laser-driven ion acceleration is presented, which allows us to create solid state targets consisting of initially gaseous materials. In particular, the use of deuterium and the methods for its preparation as a target material for laser-driven ion acceleration are discussed. Moving in the phase diagram through the liquid phase leads to the substance covering an aperture on a cooled copper frame where it is solidified through further cooling. An account of characterization techniques for target thickness is given, with a focus on deducing thickness values from distance values delivered by chromatic confocal sensors. [ABSTRACT FROM AUTHOR]

We review experimental techniques in our laboratory for nuclear magnetic resonance (NMR) in zero and ultralow magnetic field (below 0.1 μT) where detection is based on a low-cost, non-cryogenic, spin-exchange relaxation free 87Rb atomic magnetometer. The typical sensitivity is 20-30 fT/Hz1/2 for signal frequencies below 1 kHz and NMR linewidths range from Hz all the way down to tens of mHz. These features enable precision measurements of chemically informative nuclear spin-spin couplings as well as nuclear spin precession in ultralow magnetic fields. [ABSTRACT FROM AUTHOR]

A new miniature high-pressure diamond anvil cell was designed and constructed using 3D micro laser sintering technology. This is the first application of the use of rapid prototyping technology to construct high-pressure apparatus. The cell is specifically designed for use as an X-ray diffraction cell that can be used with commercially available diffractometers and open-flow cryogenic equipment to collect data at low temperature and high pressure. The cell is constructed from stainless steel 316L and is about 9 mm in diameter and 7 mm in height, giving it both small dimensions and low thermal mass, and it will fit into the cooling envelope of a standard CryostreamTM cooling system. The cell is clamped using a customized miniature buttress thread of diameter 7 mm and pitch of 0.5 mm enabled by 3D micro laser sintering technology; such dimensions are not attainable using conventional machining. The buttress thread was used as it has favourable uniaxial load properties allowing for higher pressure and better anvil alignment. The clamp can support the load of at least 1.5 kN according to finite element analysis (FEA) simulations. FEA simulations were also used to compare the performance of the standard thread and the buttress thread, and demonstrate that stress is distributed more uniformly in the latter. Rapid prototyping of the pressure cell by the laser sintering resulted in a substantially higher tensile yield strength of the 316L stainless steel (675 MPa compared to 220 MPa for the wrought type of the same material), which increased the upper pressure limit of the cell. The cell is capable of reaching pressures of up to 15 GPa with 600 μm diameter culets of diamond anvils. Sample temperature and pressure changes on cooling were assessed using X-ray diffraction on samples of NaCl and HMT-d12. [ABSTRACT FROM AUTHOR]

A new electrostatic ion storage ring, the RIKEN cryogenic electrostatic ring, has been commissioned with a 15-keV ion beam under cryogenic conditions. The ring was designed with a closed ion beam orbit of about 2.9 m, where the ion beam is guided entirely by electrostatic components. The vacuum chamber of the ring is cooled using a liquid-He-free cooling system to 4.2 K with a temperature difference of 0.4 K at most within all the positions measured by calibrated silicon diode sensors. The first cryogenic operation with a 15-keV Ne+ beam was successfully performed in August 2014. During the measurement, the Ne+ beam was stored under a ring temperature of 4.2 K with a residualgas lifetime of more than 10 min. This permits an estimation of the residual gas density at a few 104 cm-3, which corresponds to a room-temperature-equivalent pressure of around 1 × 10-10 Pa. An effect of longitudinal pulse compression at the bunching cavity in the ring was clearly identified by monitoring the pick-up beam detector. The detailed design and mechanical structure of the storage ring, as well as the results from the commissioning run, are reported. [ABSTRACT FROM AUTHOR]

A new method of probing mechanical losses and comparing the corresponding deposition processes of metallic and dielectric coatings in 1-100 MHz frequency range and cryogenic temperatures is presented. The method is based on the use of high-quality quartz acoustic cavities whose internal losses are orders of magnitude lower than any available coating nowadays. The approach is demonstrated for chromium, chromium/gold, and multilayer tantala/silica coatings. The Ta2O5/SiO2 coating has been found to exhibit a loss angle lower than 1.6 × 10-5 near 30 MHz at 4 K. The results are compared to the previous measurements. [ABSTRACT FROM AUTHOR]

This work describes the experimental apparatus based on the Mach-Zehnder interferometer for measuring the electro-optic coefficient during and after the photo-assisted poling process using a continuous light excitation. We also show that the poling can be performed at cryogenic temperatures. The setup is based on the superposition of a Mach-Zehnder AC modulation voltage on the DC bias voltage required to promote the chromophore orientation during light excitation. The effect of the reversible polarization due to the DC bias voltage applied to the polymer film is considered to calculate the electro-optic coefficient during the photo-assisted poling process. The usefulness of our setup is demonstrated with three polymer films, with different electro-optic activities: guest-host, copolymer, and homopolymer, all based on methyl methacrylate monomers and containing disperse red-1 chromophores. [ABSTRACT FROM AUTHOR]

The thermal conductivity, electrical resistivity, and bending stiffness of a carbon fiber archery arrow shaft were measured in order to determine if it would be a good material to use as a structural support in a cryogenic environment. It shows promise because of its thin cross section and structural rigidity. The thermal conductivity of the material was measured from 0.1 K to 1 K to be κ (T) = 8.8 × 1 0 − 5 T 1.54 W cm K , which is on the order of other thermal insulating materials used at cryogenic temperatures. The electrical resistivity is 0.044 Ω cm at 0.2 K, and the bending stiffness is 243 N m2 at room temperature. The shafts were machined to reduce overall thermal conductance. The reduction in thermal resistivity was calculated, and the change in stiffness was measured after shafts were machined. The shafts were used to form a support structure for an adiabatic demagnetization refrigerator. The heat load was then calculated. The carbon fiber arrow shaft provides an outstanding, thermal insulating support structure. [ABSTRACT FROM AUTHOR]