Search

We developed a high-spatial-resolution scanning x-ray fluorescence microscope (SXFM) using Kirkpatrick-Baez mirrors. As a result of two-dimensional focusing tests at BL29XUL of SPring-8, the full width at half maximum of the focused beam was achieved to be 50×30 nm2 (V×H) under the best focusing conditions. The measured beam profiles were in good agreement with simulated results. Moreover, beam size was controllable within the wide range of 30–1400 nm by changing the virtual source size, although photon flux and size were in a trade-off relationship. To demonstrate SXFM performance, a fine test chart fabricated using focused ion beam system was observed to determine the best spatial resolution. The element distribution inside a logo mark of SPring-8 in the test chart, which has a minimum linewidth of approximately 50–60 nm, was visualized with a spatial resolution better than 30 nm using the smallest focused x-ray beam. [ABSTRACT FROM AUTHOR]

The spatial resolution of scanning x-ray microscopy depends on the beam size of focused x rays. Recently, nearly diffraction-limited line focusing has been achieved using elliptical mirror optics at the 100 nm level. To realize such focusing two-dimensionally in a Kirkpatrick-Baez system, the required accuracies of the mirror aligners in this system were estimated using optical simulators based on geometrical or wave-optical theories. A focusing unit fulfilling the required adjustment accuracies was constructed. The relationships between alignment errors and focused beam profiles were quantitatively examined at the 1 km long beamline (BL29XUL) of SPring-8 to be in good agreement with the simulation results. [ABSTRACT FROM AUTHOR]

Results of measurements made using the multipole wiggler at beamline 16 of Photon Factory are reported. Double crystal rocking carves, Si ( 1 11 ) and Si (333) topographs, and thermal maps of the cooled-crystal surface were measured at total incident power levels up to 1600 W and power densities up to 0.7 W/mm², for two different crystal designs. Significant crystal deformation occurred in the form of surface curvature for both designs. Finite element calculations provided a preview of the experimental results and proved very valuable in interpretation of the measurements. [ABSTRACT FROM AUTHOR]

This article describes the outline of a time-resolved x-ray measurement system developed at the Photon Factory to study the pulsed laser annealing of silicon crystals. This system consists of a triple-crystal diffractometer, Q-switched Nd:YAG laser, and two fast detector electronics using a plastic scintillation counter, and enables us to examine the time-change behavior of nearly intrinsic rocking curves under laser irradiation with a time resolution of about 50 ns. The difference in the recovery from lattice deformation between 1.06-μm laser annealing and 0.53-μm laser annealing is clarified. [ABSTRACT FROM AUTHOR]

X-ray intensity versus energy (I-E) curves were measured in order to obtain the rod profiles. The three-dimensional surface structures of Si(111)√3 × √3-Biand -Ag were analyzed. The adsorption sites with respect to the crystal were derived from the intensity changes along the integral-order rods especially near the Bragg points by utilizing the interference effect between the x rays diffracted from the adsorbed layer and the bulk crystal. The positions of the surface Si atoms were studied by using the interference effect between the x rays diffracted from the adsorbed layer and the surface Si layer. [ABSTRACT FROM AUTHOR]

The search for the violation of the fundamental symmetry in a radioactive atom is the promising candidate for precision tests of the standard model and its possible extensions. The subtle signal arising from the symmetry violation is enhanced in heavy atoms, such as a francium (Fr). To real- ize high precision measurements, a large amount of radioactive isotopes is required. The Fr is produced via a nuclear fusion reaction using a melted gold target with a 18O primary beam at Cyclotron and Radioisotope Center, Tohoku University. The maximum extraction efficiency of the Fr ion was achieved at approximately 35%. The beam line consists of an electrostatic deflector, three electrostatic quadrupole triplets to the measurement area at 10 m away from the reaction point, and several beam diagnosis systems. We optimized parameters of the beam line. [ABSTRACT FROM AUTHOR]

Design and experience of the initial operation Of a new beamline (BL-16) for a 3.6-m-long, 53pole wiggler/undulator constructed at the Photon Factory are described. The insertion device has hybrid permanent magnets with a period of 12 cm and a maximum magnetic field of 1.47 T. In the undulator mode, the energy of the fundamental peak can be varied from 40 to 400 eV. In the wiggler mode, an x-ray beam (critical energy of 6 keV) 50-100 times more intense than that from the bending magnets is obtained. The beamline consists of two time-shared branch lines: a side beamline for soft x-rays in the undulator operation, to which photon beams are deflected sideways by a cylindrical SiC mirror, and a straight line for hard x rays under the wiggler operation. On the hard x-ray line, a fixed-exit sagittal-focusing double-crystal monochromator has been installed and commissioned. Collimating and refocusing mirrors will be installed in 1989. On the undulator beamline, a soft x-ray monochromator utilizing sophisticatedly devised aberration correction optics is commissioned. [ABSTRACT FROM AUTHOR]

To investigate photoinduced phenomena in various materials and molecules, ultrashort pulsed x-ray and electron sources with high brightness and high repetition rates are required. The x-ray and electron's typical and de Broglie wavelengths are shorter than lattice constants of materials and molecules. Therefore, photoinduced structural dynamics on the femtosecond to picosecond timescales can be directly observed in a diffraction manner by using these pulses. This research created a tabletop ultrashort pulsed electron diffraction setup that used a femtosecond laser and electron pulse compression cavity that was directly synchronized to the microwave master oscillator (∼3 GHz). A compressed electron pulse with a 1 kHz repetition rate contained 228 000 electrons. The electron pulse duration was estimated to be less than 100 fs at the sample position by using photoinduced immediate lattice changes in an ultrathin silicon film (50 nm). The newly developed time-resolved electron diffraction setup has a pulse duration that is comparable to femtosecond laser pulse widths (35-100 fs). The pulse duration, in particular, fits within the timescale of photoinduced phenomena in quantum materials. Our developed ultrafast time-resolved electron diffraction setup with a sub-100 fs temporal resolution would be a powerful tool in material science with a combination of optical pump-probe, time-resolved photoemission spectroscopic, and pulsed x-ray measurements.

A hybrid deformable x-ray mirror consisting of a mechanical bender and a bimorph deformable mirror has been developed to realize adaptive optical systems, such as zoom condenser optics, for synchrotron-radiation-based x-ray microscopy. In the developed system, both bending mechanisms comprehensively contribute to the formation of the target mirror shape and can narrow the role of piezoelectric actuators, thereby enabling a more stable operation. In this study, the behavior of the bimorph mirror under the clamped condition was investigated, and the sharing of the deformation amount for each bending mechanism was optimized to minimize the amplitude of the voltage distribution of the bimorph mirror.

We developed micro-liquid enclosure arrays (MLEAs) for holding solution samples in coherent diffractive imaging (CDI) using x-ray free-electron lasers (XFELs). Hundreds of fully isolated micro-liquid enclosures are arranged in a single MLEA chip for efficient measurement, where each enclosure is destroyed after exposure to a single XFEL pulse. A semi-automated MLEA assembling system was also developed to enclose solution samples into MLEAs efficiently at high precision. We performed XFEL-based CDI experiments using MLEAs and imaged in-solution structures of self-assembled gold nanoparticles. The sample hit rate can be optimized by adjusting solution concentration, and we achieved a single-particle hit rate of 31%, which is not far from the theoretical upper limit of 37% derived from the Poisson statistics. MELAs allow us to perform CDI measurement under controlled solution conditions and will help reveal the nanostructures and dynamics of particles in solution.

In this study, the systematic errors of an X-ray single-grating interferometer based on the Talbot effect were investigated in detail. Non-negligible systematic errors induced by an X-ray camera were identified and a method to eliminate the systematic error was proposed. Systematic-error-free measurements of the wavefront error produced by multilayer focusing mirrors with large numerical apertures were demonstrated at the SPring-8 Angstrom Compact free electron LAser. Consequently, wavefront aberration obtained with two different cameras was found to be consistent with an accuracy better than λ/12.

We have developed a method of fabricating speckle-free channel-cut crystal optics with plasma chemical vaporization machining, an etching method using atmospheric-pressure plasma, for coherent X-ray applications. We investigated the etching characteristics to silicon crystals and achieved a small surface roughness of less than 1 nm rms at a removal depth of >10 μm, which satisfies the requirements for eliminating subsurface damage while suppressing diffuse scattering from rough surfaces. We applied this method for fabricating channel-cut Si(220) crystals for a hard X-ray split-and-delay optical system and confirmed that the crystals provided speckle-free reflection profiles under coherent X-ray illumination.

An adaptive Kirkpatrick-Baez mirror focusing optics based on piezoelectric deformable mirrors was constructed at SPring-8 and its focusing performance characteristics were demonstrated. By adjusting the voltages applied to the deformable mirrors, the shape errors (compared to a target elliptical shape) were finely corrected on the basis of the mirror shape determined using the pencil-beam method, which is a type of at-wavelength figure metrology in the X-ray region. The mirror shapes were controlled with a peak-to-valley height accuracy of 2.5 nm. A focused beam with an intensity profile having a full width at half maximum of 110 × 65 nm (V × H) was achieved at an X-ray energy of 10 keV.

This paper describes an aerosol chamber system that can be used for calibrations and performance experiments of passive (220)Rn progeny detectors. For the purpose of this study, an aerosol generation system using carnauba wax as the aerosol material was mounted into the (220)Rn chamber. We used the chamber to measure characteristics of the equilibrium factor (F) of (220)Rn and unattached fraction (f(p)) of (220)Rn progeny, which are important parameters for dose estimation. The first experiment showed that continuous and stable generation of the unattached and aerosol-attached (220)Rn progeny concentrations was obtained. We observed that the spatial distributions in the chamber of the vertical profiles of the unattached and aerosol-attached (220)Rn progeny concentrations were homogeneous, as were the particle number concentration and count median diameter. The values of F and f(p) and their characteristics observed in this study were in the same range as the values reported from indoor measurements. We found that the characteristics of F and f(p) were dependent on the aerosol conditions (particle diameter and particle number concentration).

During a one-year long measurement period, radon and thoron data obtained by two different passive radon-thoron discriminative monitors were compared at subsurface workplaces in Hungary, such as mines (bauxite and manganese ore) and caves (medical and touristic). These workplaces have special environmental conditions, such as, stable and high relative humidity (100%), relatively stable temperature (12°C-21°C), low or high wind speed (max. 2.4 m s(-1)) and low or elevated aerosol concentration (130-60,000 particles m(-3)). The measured radon and thoron concentrations fluctuated in a wide range among the different workplaces. The respective annual average radon concentrations and their standard deviations (in brackets) measured by the passive radon-thoron discriminative monitor with cellulose filter (CF) and the passive radon-thoron discriminative monitor with sponge filter (SF) were: 350(321) Bq m(-3) and 550(497) Bq m(-3) in the bauxite mine; 887(604) Bq m(-3) and 1258(788) Bq m(-3) in the manganese ore mine; 2510(2341) Bq m(-3) and 3403(3075) Bq m(-3) in the medical cave (Hospital Cave of Tapolca); and 6239(2057) Bq m(-3) and 8512(1955) Bq m(-3) in the touristic cave (Lake Cave of Tapolca). The respective average thoron concentrations and their standard deviation (in brackets) measured by CF and SF monitors were: 154(210) Bq m(-3) and 161(148) Bq m(-3) in the bauxite mine; 187(191) Bq m(-3) and 117(147) Bq m(-3) in the manganese-ore mine; 360(524) Bq m(-3) and 371(789) Bq m(-3) in the medical cave (Hospital Cave of Tapolca); and 1420(1184) Bq m(-3) and 1462(3655) Bq m(-3) in the touristic cave (Lake Cave of Tapolca). Under these circumstances, comparison of the radon data for the SF and CF monitors showed the former were consistently 51% higher in the bauxite mine, 38% higher in the manganese ore mine, and 34% higher in the caves. Consequently, correction is required on previously obtained radon data acquired by CF monitors at subsurface workplaces to gain comparable data for SF monitors. In the case of thoron, the data were unreliable and no significant tendency was seen during the comparison therefore comparison of previously obtained thoron data acquired by either CF or SF is doubtful. There was probable influence by relative humidity on the detection response; however, the effects of the high wind speed and elevated aerosol concentration could not be excluded. The results of this study call attention to the importance of calibration under extreme environmental conditions and the need for using reliable radon-thoron monitors for subsurface workplaces.

This paper describes the development of a versatile coherent x-ray diffraction microscope capable of imaging biological specimens in solution. The microscope is a flexible platform accommodating various conditions, from low vacuum (10(-2) Pa) to helium gas filled ambient pressure. This flexibility greatly expands the application area, from in situ materials science to biology systems in their native state, by significantly relaxing restrictions to the sample environment. The coherent diffraction microscope has been used successfully to image a yeast cell immersed in buffer solution. We believe that the design of this coherent diffraction microscope can be directly adapted to various platforms such as table top soft x-ray laser, synchrotron x-ray sources, and x-ray free electron laser with minor relevant adjustments.

Radon diffusion through soil is strongly affected by the degree of water saturation of the soil pores. Methods have been developed by many researchers to measure radon diffusion coefficient. We developed an updated experimental system to estimate radon diffusion coefficients for typical types of soil in Japan and applied it to a typical loam with different water saturation levels (0-0.82). The system consists of a passive-type scintillation cell, soil column, accumulation tank, and radon source. The radon concentration in the accumulation tank is kept stable, and radon diffused through the soil column is continuously measured with the passive-type scintillation cell. We found the radon diffusion coefficients vary from 9.60 × 10(-6) m(2) s(-1) to 1.27 × 10(-7) m(2) s(-1) for the loam samples. Generally, the diffusion coefficients are almost constant for a water saturation range of 0-0.4 and decrease with increasing water saturation from 0.4 to 0.82.

To construct adaptive x-ray focusing optics whose optical parameters can be varied while performing wavefront correction, ultraprecise piezoelectric deformable mirrors have been developed. We computationally and experimentally investigated undesirable short-period deformation caused by piezoelectric actuators adhered to the substrate during mirror deformation. Based on the results of finite element method analysis, shape measurements, and the observation of x-ray reflection images, a guideline is developed for designing deformable mirrors that do not have short-period deformation errors.

We have developed an x-ray beam-position monitor for detecting the radiation properties of an x-ray free electron laser (FEL). It is composed of four PIN photodiodes that detect backscattered x-rays from a semitransparent diamond film placed in the beam path. The signal intensities from the photodiodes are used to compute the beam intensity and position. A proof-of-principle experiment at a synchrotron light source revealed that the error in the beam position is reduced to below 7 μm by using a nanocrystal diamond film prepared by plasma-enhanced chemical vapor deposition. Owing to high dose tolerance and transparency of the diamond film, the monitor is suitable for routine diagnostics of extremely intense x-ray pulses from the FEL.

A continuous measurement system, with a ventilation-type accumulation chamber, was developed for radon exhalation rate determination. A reasonable sampling flow rate for the measurement system was determined by comparing the values obtained by the system with those obtained by a grab sampling method. The sampling flow rate of passage through the scintillation cell from the accumulation chamber was varied from 0.05 to 2.0 l min(-1). The difference in pressure between the inside and outside of the accumulation chamber increased as the sampling flow rate became large, and the estimated radon exhalation rate also increased with the sampling flow rate. From these results, a reasonable sampling flow rate was estimated to be less than 0.2 l min(-1).

In situ wavefront compensation is a promising method to realize a focus size of only a few nanometers for x-ray beams. However, precise compensation requires evaluation of the wavefront with an accuracy much shorter than the wavelength. Here, we characterized a one-dimensionally focused beam with a width of 7 nm at 20 keV using a multilayer mirror. We demonstrate that the wavefront can be determined precisely from multiple intensity profiles measured around the beamwaist. We compare the phase profiles recovered from intensity profiles measured under the same mirror condition but with three different aperture sizes and find that the accuracy of phase retrieval is as small as λ∕12.

We developed a coherent x-ray diffraction microscopy (CXDM) system that enables us to precisely evaluate the electron density of an isolated sample. This system enables us to determine the dose per surface unit of x rays illuminated onto an isolated sample by combining incident x-ray intensity monitoring and the CXDM of a reference sample. By using this system, we determined the dose of x rays illuminated onto a nanostructured island fabricated by focused-ion-beam chemical vapor deposition and derived the electron density distribution of such a nanostructured island. A projection image of the nanostructured island with a spatial resolution of 24.1 nm and a contrast resolution higher than 2.3x10(7) electrons/pixel was successfully reconstructed.

For pump and probe experiments in x-ray free-electron laser (XFEL) facilities, accurate timing synchronization between short-wavelength femtosecond pulses from XFELs and short optical pulses from other light sources is required. For this purpose, the response time of a hydrothermal-method-grown ZnO is improved by over one order of magnitude via intentional iron ion doping. The fluorescence rise- and decay-time constants are measured to be less than 10 and 100 ps, respectively. Owing to its intense fluorescence even for single pulse XFEL excitation, the timing jitter of the soft x-ray pulse and timing electronics are evaluated to be less than 70 ps.

Electrostatic levitators use strong electric fields to levitate and accurately position a sample against gravity. In this study, the effects of the electric field are investigated with regard to viscosity measurements conducted with the oscillating drop method. The effects of the external field on viscosity measurements are experimentally confirmed by changing the sample size. Moreover, a numerical simulation based on a simple mass-spring-damper system can reproduce the experimental observations. Based on the above results, measurement procedures are improved. These help to minimize the effect of the positioning force and to increase the accuracy of the viscosity measurements.

The effective diffusion coefficient of radon is a very important factor in estimating the rate of radon exhalation from the ground surface. In this study, we developed an experimental system that overcomes technical problems in previous studies to accurately evaluate the effective diffusion coefficient. The radon source used for this system was the National Institute of Radiological Sciences radon chamber. This chamber is a calibrated international standard facility that can produce stable radon concentrations for long periods of time. Our tests showed that leakage of radon from the system was negligible. After the leakage test, we evaluated the effective diffusion coefficient in free-space and in dry porous materials at porosities of 35% and 45%. To ensure that the porous material in the column was as homogeneous as possible, we filled the column with an artificial soil with controlled grain size and grain composition. The measured values and theoretical calculations agreed well, which indicate that the proposed system can be used to accurately and quickly evaluate the effective diffusion coefficient.

We present the design, fabrication, and evaluation of a large total-reflection mirror for focusing x-ray free-electron laser beams to nanometer dimensions. We used an elliptical focusing mirror made of silicon that was 400 mm long and had a focal length of 550 mm. Electrolytic in-process dressing grinding was used for initial-step figuring and elastic emission machining was employed for final figuring and surface smoothing. A figure accuracy with a peak-to-valley height of 2 nm was achieved across the entire area. Characterization of the focused beam was performed at BL29XUL of SPring-8. The focused beam size was 75 nm at 15 keV, which is almost equal to the theoretical size.

An ultra-high-precision clock system for long time delay has been developed for picosecond time-resolved x-ray diffraction measurements using synchrotron radiation (SR) pulses and synchronized femtosecond laser pulses. The time delay control between pump laser pulse and the probe SR pulse was achieved by combining an in-phase quadrature modulator and a synchronous counter. This method allowed us to change the delay time by a nearly infinite amount while maintaining the precision of +/-8.40 ps. Time-resolved diffraction measurements using the delay control system were demonstrated for precise measurement of an acoustic velocity in a single crystal of gallium arsenide.

The deposition of radon decay products is not equal in each of the respiratory regions and as the presence of radon has been linked with an increase in lung cancer risk, it is important to calculate the deposition of radon decay products in each of the respiratory regions. Recently, many studies on the deposition of radon in respiratory regions have been simulated using wire screens. The systems and equipment used in those studies are not suitable for field measurements as their dimensions are relatively massive, nor can they measure continuously. We developed a continuous bronchial dosimeter (CBD) which is suitable for field measurements. It was designed with specifications that allow it to be remain compact. The CBD simulates the deposition of radon decay products in the different respiratory regions by the use of a combination of wire screens. Deposition in the simulated regions of the lung can be continuously estimated in various environments. The ratio of activities deposited in a simulated nasal cavity (N) and tracheobronchial (TB) regions was calculated from the results of simultaneous measurements using CBD-R (reference), CBD-N (nasal), and CBD-TB (tracheobronchial) measurement units. After aerosols were injected into the radon chamber, the ratio of N and TB depositions decreased. This results indicate that the CBD gave a good response to changes in the environment. It was found that the ratio of N and TB deposition also varied with time in each actual environment.

A compact electrostatic levitator was developed for the structural analysis of high-temperature liquids by x-ray diffraction methods. The size of the levitator was 200 mm in diameter and 200 mm in height and can be set up on a two axis diffractometer with a laboratory x-ray source, which is very convenient in performing structural measurements of high-temperature liquids. In particular, since the laboratory x-ray source allows a great amount of user time, preliminary or challenging experiments can be performed with trial and error, which prepares and complements synchrotron x-ray experiments. The present small apparatus also provides the advantage of portability and facility of setting. To demonstrate the capability of this electrostatic levitator, the static structure factors of alumina and silicon samples in their liquid phases were successfully measured.