Search

AlGaN-based ultraviolet (UV) light-emitting diodes (LEDs) are expected to have various applications, including sensing and printing, and light with ultraviolet-C (UVC) wavelengths has a virus inactivation effect. The metalorganic vapor phase epitaxy (MOVPE) method has been used to fabricate LED devices with film control and impurity doping. However, to achieve high luminous efficiency, highly crystalline aluminum nitride (AlN) must be grown in the underlying layer. Although high temperatures are required to grow high-quality AlN for strong migration at the surface, there is a trade-off in the high temperature promoting parasitic reactions. These parasitic reactions are more dominant at a high V/III ratio with more raw material in the case of using the conventional MOVPE. Here, we used jet stream gas flow MOVPE to investigate the effect of V/III ratio dependencies in optimizing AlN growth and without affecting parasitic reaction conditions. As a result, trends of typical AlN crystal growth at V/III-ratio dependencies were obtained. AlN is more stable at a higher V/III ratio of 1000, exhibiting a double atomic step surface, and the crystal orientation is further improved at 1700 °C compared to that at a lower V/III ratio. [ABSTRACT FROM AUTHOR]

Non-polar m-plane GaN terahertz quantum cascade laser (THz-QCL) structures have been studied. One is traditional three-well resonant-phonon (RP) design scheme. The other is two-well phonon scattering injection (PSI) design scheme. The peak gains of 41.8 and 44.2 cm−1 have been obtained at 8.2 and 7.7 THz respectively at 300 K according to the self-consistent non-equilibrium Green's function calculation. Different from the usual GaAs two-well design, the upper and lower lasing levels are both ground states in the GaN quantum wells for the PSI scheme, mitigating the severe broadening effect for the excited states in GaN. To guide the fabrication of such devices, the doping effect on the peak gain has been analyzed. The two designs have demonstrated distinct doping density dependence and it is mainly attributed to the very different doping dependent broadening behaviors. The results reveal the possibility of GaN based THz-QCL lasing at room temperature. [ABSTRACT FROM AUTHOR]

Deep ultraviolet light-emitting diodes have attracted considerable attention for realizing virus inactivation applications. The UV-LEDs use the AlN underlying layer and the plane sapphire substrate. However, the low growth temperature in AlN underlying layer is grown by limited growth temperature in conventional MOVPE, and high temperature is preferable for AlN growth. Furthermore, the AlN underlying layer has many dislocations owing to the active layer in the device region when the flat sapphire substrate was used with a dislocation value of > 109 cm−2. We showed the high-temperature crystal growth of AlN with a temperature of 1700 °C by high temperature and gas flow velocity MOVPE. The achieved dislocation density was ~ 4 × 108 cm−2. Additionally, this data means the low dislocation densities in the AlN layer with a growth time of only 15 min and a dislocation density of < 1 × 109 cm−2 are obtained. The AlN growth temperature exceeding 1550 °C decreases the growth rate. These results indicate desorption from the surface of the substrate in a hydrogen atmosphere. Furthermore, the characteristic dislocation behavior of AlN in high-temperature growth at 1700 °C was elucidated from TEM images. [ABSTRACT FROM AUTHOR]

The recent designs of terahertz quantum cascade lasers usually employ the short periodic length and also the tall barriers for high-temperature operation. In this work, the effect of high-energy lying non-relevant subbands is studied based on nonequilibrium Green's function formalisms model, demonstrating those subbands are probable to play a minor role on the population inversion, but play a major role on the optical gain at high temperatures. The phenomenon can be ascribed to the appearance of leakages crossing neighboring periods via sequential resonant tunneling, and those leakages are inherently created by the specific features of the two-well configuration in this design that the phonon well should be wide enough for performing the phonon scattering to depopulate the lower-laser subband. The narrower periodic length design can strengthen this inter-period leakage. A parasitic absorption between the first high-lying nonrelevant subbands from two laser wells can closely overlap the gain shape and thus significantly reduce the peak gain. [ABSTRACT FROM AUTHOR]

Recent renewed operating temperatures in terahertz quantum cascade lasers emphasize on narrowing the periodic length in a 2-well resonant-phonon design for a clean quantum level structure, in which the depopulation energy is significantly higher than one longitudinal phonon. In this study, various depopulation energies (small and large) are engineered in a 2-well design; the effect of the high-lying nonrelevant levels on the currents are systematically studied by using the non-equilibrium Green's function method. The engineering of the depopulation energy is unable to avoid the formation of leakage channels, which are activated within at least three neighboring periods via sequential close tunneling. However, a large depopulation energy relaxes the thermal backfilling process; as a result, the net leakages at high temperatures can be significantly suppressed. In addition, pre-alignment remains a critical issue in the design when using a large depopulation energy, which requires improved engineering for the barriers to obtain better laser dynamics. [ABSTRACT FROM AUTHOR]

AlGaN-based deep ultraviolet light-emitting diodes (LEDs) have a wide range of applications such as medical diagnostics, gas sensing, and water sterilization. Metal–organic vapor phase epitaxy (MOVPE) method is used for the growth of all-in-one structures, including doped layer and thin multilayers, using metal–organic and gas source raw materials for semiconductor devices. For AlN growth with high crystalline quality, high temperature is necessary to promote the surface migration of Al atoms and Al-free radicals. However, increase in temperature generates parasitic gas-phase prereactions such as adduct formation. In this work, AlN growth at 1500 °C by a stable vapor phase reaction has been achieved by jet stream gas flow metal–organic vapor phase epitaxy. The AlN growth rate increases with gas flow velocity and saturates at ~ 10 m/s at room temperature. Moreover, it is constant at an ammonia flow rate at a V/III ratio from 50 to 220. These results demonstrate the reduction in adduct formation, which is a typical issue with the vapor phase reaction between triethylaluminum and ammonia. The developed method provides the in-plane uniformity of AlN thickness within 5%, a low concentration of unintentionally doped impurities, smooth surface, and decrease in dislocation density because of the suppression of parasitic reactions. [ABSTRACT FROM AUTHOR]

Crystal growth of eco-friendly, ultrawide bandgap aluminium gallium nitride (AlGaN) semiconductor-based ultraviolet-B (UVB) light-emitting diodes (LEDs) hold the potential to replace toxic mercury-based ultraviolet lamps. One of the major drawbacks in the utilisation of AlGaN-based UVB LEDs is their low efficiency of about 6.5%. The study investigates the influence of Al-graded p-type multi-quantum-barrier electron-blocking-layer (Al-grad p-MQB EBL) and Al-graded p-AlGaN hole source layer (HSL) on the generation and injection of 3D holes in the active region. Using the new UVB LED design, a significant improvement in the experimental efficiency and light output power of about 8.2% and 36 mW is noticed. This is accomplished by the transparent nature of Al-graded Mg-doped p-AlGaN HSL for 3D holes generation and p-MQB EBL structure for holes transport toward multi-quantum-wells via intra-band tunnelling. Based on both the numerical and experimental studies, the influence of sub-nanometre scale Ni film deposited underneath the 200 nm-thick Al-film p-electrode on the optical reflectance in UVB LED is investigated. A remarkable improvement in the efficiency of up to 9.6% and light output power of 40 mW, even in the absence of standard package, flip-chip, and resin-like lenses, is achieved on bare-wafer under continuous-wave operation at room temperature. The enhanced performance is attributed to the use of Al-graded p-MQB EBL coupled with softly polarised p-AlGaN HSL and the highly reflective 0.4 nm-thick Ni and 200 nm-thick Al p-electrode in the UVB LED. This research study provides a new avenue to improve the performance of high-power p-AlGaN-based UVB LEDs and other optoelectronic devices in III–V semiconductors. [ABSTRACT FROM AUTHOR]

The key challenge for terahertz quantum cascade lasers (THz-QCLs) is to make it operating at room-temperature. The suppression of thermally activated leakages via high lying quantum levels is emphasized recently. In this study, we employ the advanced self-consistent method of non-equilibrium Green's function, aiming to reveal those kinds of leakages in the commonly used THz-QCL designs based on 2-, 3- and 4-quantum well. At the high temperature of 300 K, if all the confined high lying quantum levels and also the continuums are included within three neighboring periods, leakages indeed possess high fraction of the total current (21%, 30%, 50% for 2-, 3- and 4-quantum well designs, respectively). Ministep concept is introduced to weaken those leakage channels by isolating the desired levels from high lying ones, thus the leakages are well suppressed, with corresponding fractions less than 5% for all three designs. [ABSTRACT FROM AUTHOR]

Operating at high temperatures in the range of thermoelectric coolers is essential for terahertz quantum cascade lasers to real applications. The use of scattering-assisted injection scheme enables an increase in operating temperature. This concept, however, has not been implemented in a short-period structure consisting of two quantum wells. In this work, based on non-equilibrium Green's function calculations, it emphasizes on the current leakage and parasitic absorption via high-energy states as fundamental limitations in this scheme with short-period. A new design concept employing asymmetric wells composition is proposed to suppress these limitations. A peak gain of 40 cm−1 at 230 K is predicted in the GaAs/AlGaAs semiconductor material system with an emission frequency of 3.5 THz. [ABSTRACT FROM AUTHOR]

An AlN template layer is required for growth of AlGaN-based deep ultraviolet light-emitting diodes (UV-LEDs). However, the crystal quality of AlN templates grown on both flat and patterned Si substrates has so far been insufficient for replacing templates grown on sapphire substrates. In this work, we grew a high-quality AlN template on 2 in. micro-circle-patterned Si substrate (mPSiS) with two different sizes and shapes through controlling the bias power of inductively coupled plasma (ICP) etching. The experimental results showed that the best AlN template was obtained on a large pattern size with a bow-angle shape and the template had X-ray rocking curves with full widths at half-maximum of 620 and 1141 arcsec for the (002) and (102) reflection planes. The threading dislocation density near surface of AlN template through transmission electron microscopy (TEM) estimation was in the order of 107 cm−2, which is the lowest dislocation density reported for a Si substrate to our knowledge. A strong single electroluminescence (EL) peak was also obtained for an AlGaN-based deep UV-LED grown on this template, means that it can be used for further developing high-efficiency deep UV-LEDs. [ABSTRACT FROM AUTHOR]