Search

Data authenticated aggregation is always a significant issue for wireless sensor networks (WSNs). The marine sensors are deployed far away from the security monitoring. Secure data aggregation for marine WSNs has emerged and attracted the interest of researchers and engineers. A multi-signature enables the data aggregation through one signature to authenticate various signers on the acknowledgement of a message, which is quite fit for data authenticated aggregation marine WSNs. However, most of the previous multi-signature schemes rely on the technique of bilinear pairing involving heavy computational overhead or the management of certificates, which cannot be afforded by the marine wireless sensors. Combined with the concept of identity-based cryptography, a few pairing-free identity-based multi-signature (IBMS) schemes have been designed on the basis of the integer factorization problem. In this paper, we propose two efficient IBMS schemes that can be used to construct provably secure data authenticated aggregation protocols under the cubic residue assumption, which is equal to integer factorization. We also employ two different methods to calculate a cubic root for the cubic residue number during the signer’s private key extraction. The algorithms are quite efficient compared to the previous work, especially for the algorithms of the multi-signature generation and its verification.

This study investigates the design and fabrication of magnetic microsensors using the commercial 0.35 μm complementary metal oxide semiconductor (CMOS) process. The magnetic sensor is composed of springs and interdigitated electrodes, and it is actuated by the Lorentz force. The finite element method (FEM) software CoventorWare is adopted to simulate the displacement and capacitance of the magnetic sensor. A post-CMOS process is utilized to release the suspended structure. The post-process uses an anisotropic dry etching to etch the silicon dioxide layer and an isotropic dry etching to remove the silicon substrate. When a magnetic field is applied to the magnetic sensor, it generates a change in capacitance. A sensing circuit is employed to convert the capacitance variation of the sensor into the output voltage. The experimental results show that the output voltage of the magnetic microsensor varies from 0.05 to 1.94 V in the magnetic field range of 5–200 mT.

The study presents an ammonia microsensor integrated with a readout circuit on-a-chip fabricated using the commercial 0.18 μm complementary metal oxide semiconductor (CMOS) process. The integrated sensor chip consists of a heater, an ammonia sensor and a readout circuit. The ammonia sensor is constructed by a sensitive film and the interdigitated electrodes. The sensitive film is zirconium dioxide that is coated on the interdigitated electrodes. The heater is used to provide a working temperature to the sensitive film. A post-process is employed to remove the sacrificial layer and to coat zirconium dioxide on the sensor. When the sensitive film adsorbs or desorbs ammonia gas, the sensor produces a change in resistance. The readout circuit converts the resistance variation of the sensor into the output voltage. The experiments show that the integrated ammonia sensor has a sensitivity of 4.1 mV/ppm.

This paper presents the fabrication and characterization of energy harvesting thermoelectric micro generators using the commercial complementary metal oxide semiconductor (CMOS) process. The micro generator consists of 33 thermocouples in series. Thermocouple materials are p-type and n-type polysilicon since they have a large Seebeck coefficient difference. The output power of the micro generator depends on the temperature difference in the hot and cold parts of the thermocouples. In order to increase this temperature difference, the hot part of the thermocouples is suspended to reduce heat-sinking. The micro generator needs a post-CMOS process to release the suspended structures of hot part, which the post-process includes an anisotropic dry etching to etch the sacrificial oxide layer and an isotropic dry etching to remove the silicon substrate. Experiments show that the output power of the micro generator is 9.4 mW at a temperature difference of 15 K.

This work presents a thermoelectric micro generator fabricated by the commercial 0.35 μm complementary metal oxide semiconductor (CMOS) process and the post-CMOS process. The micro generator is composed of 24 thermocouples in series. Each thermocouple is constructed by p-type and n-type polysilicon strips. The output power of the generator depends on the temperature difference between the hot and cold parts in the thermocouples. In order to prevent heat-receiving in the cold part in the thermocouples, the cold part is covered with a silicon dioxide layer with low thermal conductivity to insulate the heat source. The hot part of the thermocouples is suspended and connected to an aluminum plate, to increases the heat-receiving area in the hot part. The generator requires a post-CMOS process to release the suspended structures. The post-CMOS process uses an anisotropic dry etching to remove the oxide sacrificial layer and an isotropic dry etching to etch the silicon substrate. Experimental results show that the micro generator has an output voltage of 67 μV at the temperature difference of 1 K.

The study investigates a capacitive micro pressure sensor integrated with a ring oscillator circuit on a chip. The integrated capacitive pressure sensor is fabricated using the commercial CMOS (complementary metal oxide semiconductor) process and a post-process. The ring oscillator is employed to convert the capacitance of the pressure sensor into the frequency output. The pressure sensor consists of 16 sensing cells in parallel. Each sensing cell contains a top electrode and a lower electrode, and the top electrode is a sandwich membrane. The pressure sensor needs a post-CMOS process to release the membranes after completion of the CMOS process. The post-process uses etchants to etch the sacrificial layers, and to release the membranes. The advantages of the post-process include easy execution and low cost. Experimental results reveal that the pressure sensor has a high sensitivity of 7 Hz/Pa in the pressure range of 0–300 kPa.

In this study, we fabricated a wireless micro FET (field effect transistor) pressure sensor based on the commercial CMOS (complementary metal oxide semiconductor) process and a post-process. The wireless micro pressure sensor is composed of a FET pressure sensor, an oscillator, an amplifier and an antenna. The oscillator is adopted to generate an ac signal, and the amplifier is used to amplify the sensing signal of the pressure sensor. The antenna is utilized to transmit the output voltage of the pressure sensor to a receiver. The pressure sensor is constructed by 16 sensing cells in parallel. Each sensing cell contains an MOS (metal oxide semiconductor) and a suspended membrane, which the gate of the MOS is the suspended membrane. The postprocess employs etchants to etch the sacrificial layers in the pressure sensor for releasing the suspended membranes, and a LPCVD (low pressure chemical vapor deposition) parylene is adopted to seal the etch holes in the pressure. Experimental results show that the pressure sensor has a sensitivity of 0.08 mV/kPa in the pressure range of 0–500 kPa and a wireless transmission distance of 10 cm.

In this study we used the commercial 0.35 µm CMOS (complementary metal oxide semiconductor) process and simple maskless post-processing to fabricate an array of micromirrors exhibiting high natural frequency. The micromirrors were manufactured from aluminum; the sacrificial layer was silicon dioxide. Because we fabricated the micromirror arrays using the standard CMOS process, they have the potential to be integrated with circuitry on a chip. For post-processing we used an etchant to remove the sacrificial layer and thereby suspend the micromirrors. The micromirror array contained a circular membrane and four fixed beams set symmetrically around and below the circular mirror; these four fan-shaped electrodes controlled the tilting of the micromirror. A MEMS (microelectromechanical system) motion analysis system and a confocal 3D-surface topography were used to characterize the properties and configuration of the micromirror array. Each micromirror could be rotated in four independent directions. Experimentally, we found that the micromirror had a tilting angle of about 2.55° when applying a driving voltage of 40 V. The natural frequency of the micromirrors was 59.1 kHz.

This study presents the fabrication and characterization of a micromechanical tunable in-plane resonator. The resonator is manufactured using the commercial 0.35 µm complementary metal oxide semiconductor (CMOS) process. The resonator is made of aluminum, and the sacrificial layer is silicon dioxide. The post-process involves only one maskless etching step using an etchant to remove the sacrificial layer. The resonator includes three parts: a driving part to provide a driving force, a sensing part that is used to detect a change in capacitance when the resonator is vibrating, and a tuning part that changes the resonant frequency of the resonator. The main advantages of the tunable resonator are a low driving voltage and compatibility with the CMOS process. The resonant frequency of the resonator can be changed upon applying a dc voltage to the tuning part. To reduce the driving voltage, the driving part is designed as comb-finger rows. Experimental results show that the resonator has a resonant frequency of about 183 kHz and a driving voltage of 10 V; the resonant frequency increases 14 kHz when a tuning voltage of 30 V is applied. The resonator has a maximum frequency–tuning ratio of 7.6%.

This study presents the simulation, fabrication and characterization ofmicromechanical radio frequency (RF) switch with micro inductors. The inductors areemployed to enhance the characteristic of the RF switch. An equivalent circuit model isdeveloped to simulate the performance of the RF switch. The behaviors of themicromechanical RF switch are simulated by the finite element method software,CoventorWare. The micromechanical RF switch is fabricated using the complementarymetal oxide semiconductor (CMOS) and a post-process. The post-process employs a wetetching to etch the sacrificial layer, and to release the suspended structures of the RF switch.The structure of the RF switch contains a coplanar waveguide (CPW), a suspendedmembrane, eight springs and two inductors in series. Experimental results reveal that theinsertion loss and isolation of the switch are 1.7 dB at 21 GHz and 19 dB at 21 GHz,respectively. The driving voltage of the switch is about 13 V.

This paper presents the simulation, fabrication and characterization of a microFET (field effect transistor) pressure sensor with readout circuits. The pressure sensorincludes 16 sensing cells in parallel. Each sensing cell that is circular shape is composed ofan MOS (metal oxide semiconductor) and a suspended membrane, which the suspendedmembrane is the movable gate of the MOS. The CoventorWare is used to simulate thebehaviors of the pressure sensor, and the HSPICE is employed to evaluate the characteristicsof the circuits. The pressure sensor integrated with circuits is manufactured using thecommercial 0.35 μm CMOS (complementary metal oxide semiconductor) process and apost-process. In order to obtain the suspended membranes, the pressure sensor requires apost-CMOS process. The post-process adopts etchants to etch the sacrificial layers in thepressure sensors to release the suspended membranes, and then the etch holes in the pressuresensor are sealed by LPCVD (low pressure chemical vapor deposition) parylene. Thepressure sensor produces a change in current when applying a pressure to the sensing cells.The circuits are utilized to convert the current variation of the pressure sensor into thevoltage output. Experimental results show that the pressure sensor has a sensitivity of 0.032mV/kPa in the pressure range of 0-500 kPa.