Search

Although wireless devices continuously gain communication capabilities, even state-of-the-art Industrial Internet of Things (IIoT) architectures, such as Internet Protocol version 6 over the Time-Slotted Channel Hopping (TSCH) mode of IEEE 802.15.4 (6TiSCH), continue to use network-wide, fixed link configurations. This presents a missed opportunity to (1) forego the need for rigorous manual setup of new deployments; and (2) provide full coverage of particularly heterogeneous and/or dynamic industrial sites. As such, we devised the Multi-Modal Minimal Scheduling Function (3MSF) for the TSCH link layer, which, combined with previous work on the routing layer, results in a 6TiSCH architecture able to dynamically exploit modern multi-modal hardware on a per-link basis through variable-duration timeslots, simultaneous transmission, and routing metric normalization. This paper describes, in great detail, its design and discusses the rationale behind every choice made. Finally, we evaluate three basic scenarios through simulations, showcasing both the functionality and flexibility of our 6TiSCH implementation.

The capacity to update firmware is a vital component in the lifecycle of Internet of Things (IoT) devices, even those with restricted hardware resources. This paper explores the best way to wirelessly (Over The Air, OTA) update low-end IoT nodes with difficult access, combining the use of unicast and broadcast communications. The devices under consideration correspond to a recent industrial IoT project that focuses on the installation of intelligent lighting systems within ATEX (potentially explosive atmospheres) zones, connected via LoRa to a gateway. As energy consumption is not limited in this use case, the main figure of merit is the total time required for updating a project. Therefore, the objective is to deliver all the fragments of the firmware to each and all the nodes in a safe way, in the least amount of time. Three different methods, combining unicast and broadcast transmissions in different ways, are explored analytically, with the aim of obtaining the expected update time. The methods are also tested via extensive simulations, modifying different parameters such as the size of the scenario, the number of bytes of each firmware chunk, the number of nodes, and the number of initial broadcast rounds. The simulations show that the update time of a project can be significant, considering the limitations posed by regulations, in terms of the percentage of airtime consumption. However, significant time reductions can be achieved by using the proper method: in some cases, when the number of nodes is high, the update time can be reduced by two orders of magnitude if the correct method is chosen. Moreover, one of the proposed methods is implemented using actual hardware. This real implementation is used to perform firmware update experiments in a lab environment. Overall, the article illustrates the advantage of broadcast approaches in this kind of technology, in which the transmission rate is constant despite the distance between the gateway and the node. However, the advantage of these broadcast methods with respect to the unicast one could be mitigated if the nodes do not run exactly the same firmware version, since the control of the broadcast update would be more difficult and the total update time would increase.

This paper proposes a new system based on the Industrial Internet of Things (IIoT) for the monitoring of Mobile Health (m-Health) of workers in the underground mining industry. The proposed architecture uses a hybrid model in data transmission. Visible Light Communication (VLC) is used for downlink because of its narrow coverage, which aids in worker positioning. Radio frequency (RF) communication technology is used to send data for primary vital signs in the uplink, which is more efficient in transmission and is a viable solution according to the problem raised. The results obtained in terms of coverage and transmission for the downlink and uplink links show the feasibility of implementing the proposed system.

The article presents an attempt to identify an appropriate regression model for the estimation of cutting tool lifespan in the milling process based on the analysis of the R 2 parameters of these models. The work is based on our own experiments and the accumulated database (which we make available for further use). The study uses a Haas VF-1 milling machine equipped with vibration sensors and based on a Beckhoff PLC data collector. As the acquired sensor data are continuous, and in order to account for dependencies between them, regression models were used. Support Vector Regression (SVR), decision trees and neural networks were tested during the work. The results obtained show that the best prediction results with the lowest error values were obtained for two-dimensional neural networks using the LBFGS solver (93.9%). Very similar results were also obtained for SVR (93.4%). The research carried out is related to the realisation of intelligent manufacturing dedicated to Industry 4.0 in the field of monitoring production processes, planning service downtime and reducing the level of losses resulting from damage to materials, semi-finished products and tools.

In recent years, the Internet of Things (IoT) has had a big impact on both industry and academia. Its profound impact is particularly felt in the industrial sector, where the Industrial Internet of Things (IIoT), also known as Industry 4.0, is revolutionizing manufacturing and production through the fusion of cutting-edge technologies and network-embedded sensing devices. The IIoT revolutionizes several industries, including crucial ones such as oil and gas, water purification and distribution, energy, and chemicals, by integrating information technology (IT) with industrial control and automation systems. Water, a vital resource for life, is a symbol of the advancement of technology, yet knowledge of potential cyberattacks and their catastrophic effects on water treatment facilities is still insufficient. Even seemingly insignificant errors can have serious consequences, such as aberrant pH values or fluctuations in the concentration of hydrochloric acid (HCI) in water, which can result in fatalities or serious diseases. The water purification and distribution industry has been the target of numerous hostile cyber security attacks, some of which have been identified, revealed, and documented in this paper. Our goal is to understand the range of security threats that are present in this industry. Through the lens of IIoT, the survey provides a technical investigation that covers attack models, actual cases of cyber intrusions in the water sector, a range of security difficulties encountered, and preventative security solutions. We also explore upcoming perspectives, illuminating the predicted advancements and orientations in this dynamic subject. For industrial practitioners and aspiring scholars alike, our work is a useful, enlightening, and current resource. We want to promote a thorough grasp of the cybersecurity landscape in the water industry by combining key insights and igniting group efforts toward a safe and dependable digital future.

Competitiveness in industry requires smooth, efficient, and high-quality operation. For some industrial applications or process control and monitoring applications, it is necessary to achieve high availability and reliability because, for example, the failure of availability in industrial production can have serious consequences for the operation and profitability of the company, as well as for the safety of employees and the surrounding environment. At present, many new technologies that use data obtained from various sensors for evaluation or decision-making require the minimization of data processing latency to meet the needs of real-time applications. Cloud/Fog and Edge computing technologies have been proposed to overcome latency issues and to increase computing power. However, industrial applications also require the high availability and reliability of devices and systems. The potential malfunction of Edge devices can cause a failure of applications, and the unavailability of Edge computing results can have a significant impact on manufacturing processes. Therefore, our article deals with the creation and validation of an enhanced Edge device model, which in contrast to the current solutions, is aimed not only at the integration of various sensors within manufacturing solutions, but also brings the required redundancy to enable the high availability of Edge devices. In the model, we use Edge computing, which performs the recording of sensed data from various types of sensors, synchronizes them, and makes them available for decision making by applications in the Cloud. We focus on creating a suitable Edge device model that works with the redundancy, by using either mirroring or duplexing via a secondary Edge device. This enables high Edge device availability and rapid system recovery in the event of a failure of the primary Edge device. The created model of high availability is based on the mirroring and duplexing of the Edge devices, which support two protocols: OPC UA and MQTT. The models were implemented in the Node-Red software, tested, and subsequently validated and compared to confirm the required recovery time and 100% redundancy of the Edge device. In the contrast to the currently available Edge solutions, our proposed extended model based on Edge mirroring is able to address most of the critical cases, where fast recovery is required, and no adjustments are needed for critical applications. The maturity level of Edge high availability can be further extended by applying Edge duplexing for process control.

Nowadays, the industrial Internet of things (IIoT) and smart factories are relying on intelligence and big data analytics for large-scale decision making. Yet, this method is facing critical challenges regarding computation and data processing due to the complexity and heterogeneous nature of big data. Smart factory systems rely primarily on the analysis results to optimize production, predict future market directions, prevent and manage risks, and so on. However, deploying the existing classical solutions such as machine learning, cloud, and AI is not effective anymore. Smart factory systems and industries need novel solutions to sustain their development. On the other hand, with the fast development of quantum information systems (QISs), multiple sectors are studying the opportunities and challenges of implementing quantum-based solutions for a more efficient and exponentially faster processing time. To this end, in this paper, we discuss the implementation of quantum solutions for reliable and sustainable IIoT-based smart factory development. We depict various applications where quantum algorithms could improve the scalability and productivity of IIoT systems. Moreover, we design a universal system model where smart factories would not need to acquire quantum computers to run quantum algorithms based on their needs; instead, they can use quantum cloud servers and quantum terminals implemented at the edge layer to help them run the desired quantum algorithms without the need of an expert. To prove the feasibility of our model, we implement two real-world case studies and evaluate their performance. The analysis shows the benefits of quantum solutions in different sectors of smart factories.

Remote monitoring and operation evaluation applications for industrial environments are modern and easy means of exploiting the provided resources of specific systems. Targeted micro hydropower plant functionalities (such as tracking and adjusting the values of functional parameters, real-time fault and cause signalizing, condition monitoring assurance, and assessments of the need for maintenance activities) require the design of reliable and efficient devices or systems. The present work describes the design and implementation procedure of an Industrial Internet of Things (IIoT) system configured for a basic micro hydropower plant architecture and assuring simple means of customization for plant differences in structure and operation. The designed system features a set of commonly used functions specific to micro hydropower exploitation, providing maximum performance and efficiency.

The high-density Industrial Internet of Things needs to meet the requirements of high-density device access and massive data transmission, which requires the support of multiple-input multiple-output (MIMO) antenna cognitive systems to keep high throughput. In such a system, spectral efficiency (SE) optimization based on dynamic power allocation is an effective way to enhance the network throughput as the channel quality variations significantly affect the spectral efficiency performance. Deep learning methods have illustrated the ability to efficiently solve the non-convexity of resource allocation problems induced by the channel multi-path and inter-user interference effects. However, current real-valued deep-learning-based power allocation methods have failed to utilize the representational capacity of complex-valued data as they regard the complex-valued channel data as two parts: real and imaginary data. In this paper, we propose a complex-valued power allocation network (AttCVNN) with cross-channel and in-channel attention mechanisms to improve the model performance where the former considers the relationship between cognitive users and the primary user, i.e., inter-network users, while the latter focuses on the relationship among cognitive users, i.e., intra-network users. Comparison experiments indicate that the proposed AttCVNN notably outperforms both the equal power allocation method (EPM) and the real-valued and the complex-valued fully connected network (FNN, CVFNN) and shows a better convergence rate in the training phase than the real-valued convolutional neural network (AttCNN).

The rapid development in manufacturing industries due to the introduction of IIoT devices has led to the emergence of Industry 4.0 which results in an industry with intelligence, increased efficiency and reduction in the cost of manufacturing. However, the introduction of IIoT devices opens up the door for a variety of cyber threats in smart industries. The detection of cyber threats against such extensive, complex, and heterogeneous smart manufacturing industries is very challenging due to the lack of sufficient attack traces. Therefore, in this work, a Federated Learning enabled Deep Intrusion Detection framework is proposed to detect cyber threats in smart manufacturing industries. The proposed FLDID framework allows multiple smart manufacturing industries to build a collaborative model to detect threats and overcome the limited attack example problem with individual industries. Moreover, to ensure the privacy of model gradients, Paillier-based encryption is used in communication between edge devices (representative of smart industries) and the server. The deep learning-based hybrid model, which consists of a Convolutional Neural Network, Long Short Term Memory, and Multi-Layer Perceptron is used in the intrusion detection model. An exhaustive set of experiments on the publically available dataset proves the effectiveness of the proposed framework for detecting cyber threats in smart industries over the state-of-the-art approaches.

While many companies worldwide are still striving to adjust to Industry 4.0 principles, the transition to Industry 5.0 is already underway. Under such a paradigm, Cyber-Physical Human-centered Systems (CPHSs) have emerged to leverage operator capabilities in order to meet the goals of complex manufacturing systems towards human-centricity, resilience and sustainability. This article first describes the essential concepts for the development of Industry 5.0 CPHSs and then analyzes the latest CPHSs, identifying their main design requirements and key implementation components. Moreover, the major challenges for the development of such CPHSs are outlined. Next, to illustrate the previously described concepts, a real-world Industry 5.0 CPHS is presented. Such a CPHS enables increased operator safety and operation tracking in manufacturing processes that rely on collaborative robots and heavy machinery. Specifically, the proposed use case consists of a workshop where a smarter use of resources is required, and human proximity detection determines when machinery should be working or not in order to avoid incidents or accidents involving such machinery. The proposed CPHS makes use of a hybrid edge computing architecture with smart mist computing nodes that processes thermal images and reacts to prevent industrial safety issues. The performed experiments show that, in the selected real-world scenario, the developed CPHS algorithms are able to detect human presence with low-power devices (with a Raspberry Pi 3B) in a fast and accurate way (in less than 10 ms with a 97.04% accuracy), thus being an effective solution (e.g., a good trade-off between cost, accuracy, resilience and computational efficiency) that can be integrated into many Industry 5.0 applications. Finally, this article provides specific guidelines that will help future developers and managers to overcome the challenges that will arise when deploying the next generation of CPHSs for smart and sustainable manufacturing.

The Zero Trust concept is being adopted in information technology (IT) deployments, while human users remain to be the main risk for operational technology (OT) deployments. This article proposes to enhance the new Modbus/TCP Security protocol with authentication and authorization functions that guarantee security against intentional unauthorized access. It aims to comply with the principle of never trusting the person who is accessing the network before carrying out a security check. Two functions are tested and used in order to build an access control method that is based on a username and a password for human users with knowledge of industrial automation control systems (IACS), using simple means, low motivation, and few resources. A man-in-the-middle (MITM) component was added in order to intermediate the client and the server communication and to validate these functions. The proposed scenario was implemented using the Node-RED programming platform. The tests implementing the functions and the access control method through the Node-RED software have proven their potential and their applicability.

The development of 5G networks has rapidly increased the use of Industrial Internet of Things (IIoT) devices for control, monitoring, and processing purposes. Biometric-based user authentication can prevent unauthorized access to IIoT devices, thereby safeguarding data security during production. However, most biometric authentication systems in the IIoT have no template protection, thus risking raw biometric data stored as templates in central databases or IIoT devices. Moreover, traditional biometric authentication faces slow, limited database holding capacity and data transmission problems. To address these issues, in this paper we propose a secure online fingerprint authentication system for IIoT devices over 5G networks. The core of the proposed system is the design of a cancelable fingerprint template, which protects original minutia features and provides privacy and security guarantee for both entity users and the message content transmitted between IIoT devices and the cloud server via 5G networks.Compared with state-of-the-art methods, the proposed authentication system shows competitive performance on six public fingerprint databases, while saving computational costs and achieving fast online matching.

With the development of the Industrial Internet of Things (IIoT), industrial wireless sensors need to upload the collected private data to the cloud servers, resulting in a large amount of private data being exposed on the Internet. Private data are vulnerable to hacking. Many complex wireless-sensor-authentication protocols have been proposed. In this paper, we proposed an efficient authentication protocol for IIoT-oriented wireless sensor networks. The protocol introduces the PUF chip, and uses the Bloom filter to save and query the challenge-response pairs generated by the PUF chip. It ensures the security of the physical layer of the device and reduces the computing cost and communication cost of the wireless sensor side. The protocol introduces a pre-authentication mechanism to achieve continuous authentication between the gateway and the cloud server. The overall computational cost of the protocol is reduced. Formal security analysis and informal security analysis proved that our proposed protocol has more security features. We implemented various security primitives using the MIRACL cryptographic library and GMP large number library. Our proposed protocol was compared in-depth with related work. Detailed experiments show that our proposed protocol significantly reduces the computational cost and communication cost on the wireless sensor side and the overall computational cost of the protocol.

The manufacturing sector is one of the areas where the advantages of digital twin technology can benefit mostly. The product development, including its software, electronics, mechanics, and physical behavior, is included in the digital twin of the product. Furthermore, simultaneous data capturing from the sensors and data processing are also available in the digital twin. This enables each phase of the development cycle to be simulated, processed, and validated to discover the potential problems before the production of real components. In this study, the use of digital twin technology in the commercial production phase of the automotive production line with a case study is introduced. This study is one of the most comprehensive studies in the literature related to automotive production; therefore, it puts forth the power of using digital twin technology in that area. As the result of this case study, a 6.01% increase in the commercial production line efficiency and an 87.56% gain for downtime are achieved.

The industry-based internet of things (IIoT) describes how IIoT devices enhance and extend their capabilities for production amenities, security, and efficacy. IIoT establishes an enterprise-to-enterprise setup that means industries have several factories and manufacturing units that are dependent on other sectors for their services and products. In this context, individual industries need to share their information with other external sectors in a shared environment which may not be secure. The capability to examine and inspect such large-scale information and perform analytical protection over the large volumes of personal and organizational information demands authentication and confidentiality so that the total data are not endangered after illegal access by hackers and other unauthorized persons. In parallel, these large volumes of confidential industrial data need to be processed within reasonable time for effective deliverables. Currently, there are many mathematical-based symmetric and asymmetric key cryptographic approaches and identity- and attribute-based public key cryptographic approaches that exist to address the abovementioned concerns and limitations such as computational overheads and taking more time for crucial generation as part of the encipherment and decipherment process for large-scale data privacy and security. In addition, the required key for the encipherment and decipherment process may be generated by a third party which may be compromised and lead to man-in-the-middle attacks, brute force attacks, etc. In parallel, there are some other quantum key distribution approaches available to produce keys for the encipherment and decipherment process without the need for a third party. However, there are still some attacks such as photon number splitting attacks and faked state attacks that may be possible with these existing QKD approaches. The primary motivation of our work is to address and avoid such abovementioned existing problems with better and optimal computational overhead for key generation, encipherment, and the decipherment process compared to the existing conventional models. To overcome the existing problems, we proposed a novel dynamic quantum key distribution (QKD) algorithm for critical public infrastructure, which will secure all cyber-physical systems as part of IIoT. In this paper, we used novel multi-state qubit representation to support enhanced dynamic, chaotic quantum key generation with high efficiency and low computational overhead. Our proposed QKD algorithm can create a chaotic set of qubits that act as a part of session-wise dynamic keys used to encipher the IIoT-based large scales of information for secure communication and distribution of sensitive information.

This article introduces a novel virtual sensor for predictive maintenance called mini-term. A mini-term can be defined as the time it takes for a part of the machine to do its job. Being a technical sub-cycle time, its function has been linked to production. However, when a machine or component gets deteriorated, the mini-term also suffers deterioration, allowing it to be a multifunctional indicator for the prediction of machine failures as well as measurement of production. Currently, in Industry 4.0, one of the handicaps is Big Data and Data Analysis. However, in the case of predictive maintenance, the need to install sensors in the machines means that when the proposed scientific solutions reach the industry, they cannot be carried out massively due to the high cost this entails. The advantage introduced by the mini-term is that it can be implemented in an easy and simple way in pre-installed systems since you only need to program a timer in the PLC or PC that controls the line/machine in the production line, allowing, according to the authors' knowledge, to build industrial Big Data on predictive maintenance for the first time, which is called Miniterm 4.0. This article shows evidence of the important improvements generated by the use of Miniterm 4.0 in a factory. At the end of the paper we show the evolution of TAV (Technical availability), Mean Time To Repair (MTTR), EM (Number of Work order (Emergency Orders/line Stop)) and OM (Labour hours in EM) showing a very important improvement as the number of mini-terms was increased and the Miniterm 4.0 system became more reliable. In particular, TAV is increased by 15%, OM is reduced in 5000 orders, MTTR is reduced in 2 h and there are produced 3000 orders less than when mini-terms did not exist. At the end of the article we discuss the benefits and limitations of the mini-terms and we show the conclusions and future works.

IoT (Internet of Things) systems are complex ones that may comprise large numbers of sensing and actuating devices; and servers that store data and further configure the operation of such devices. Usually, these systems involve real-time operation as they are closely bound to particular physical processes. This real-time operation is often threatened by the security solutions that are put in place to alleviate the ever growing attack surface in IoT. This paper focuses on critical IoT domains where less attention has been paid to the web security aspects. The main reason is that, up to quite recently, web technologies have been considered unreliable and had to be avoided by design in critical systems. In this work, we focus on the server side and on how attacks propagate from server to client as vulnerabilities and from client to unprotected servers; we describe the concerns and vulnerabilities introduced by the intensive usage of web interfaces in IoT from the server templating engines perspective. In this context, we propose an approach to perform self monitoring on the server side, propagating the self monitoring to the IoT system devices; the aim is to provide rapid detection of security vulnerabilities with a low overhead that is transparent to the server normal operation. This approach improves the control over the vulnerability detection. We show a set of experiments that validate the feasibility of our approach.

The need for reliable communications in industrial systems becomes more evident as industries strive to increase reliance on automation. This trend has sustained the adoption of WirelessHART communications as a key enabling technology and its operational integrity must be ensured. This paper focuses on demonstrating pre-deployment counterfeit detection using active 2D Distinct Native Attribute (2D-DNA) fingerprinting. Counterfeit detection is demonstrated using experimentally collected signals from eight commercial WirelessHART adapters. Adapter fingerprints are used to train 56 Multiple Discriminant Analysis (MDA) models with each representing five authentic network devices. The three non-modeled devices are introduced as counterfeits and a total of 840 individual authentic (modeled) versus counterfeit (non-modeled) ID verification assessments performed. Counterfeit detection is performed on a fingerprint-by-fingerprint basis with best case per-device Counterfeit Detection Rate (%CDR) estimates including 87.6% < %CDR < 99.9% and yielding an average cross-device %CDR ≈ 92.5%. This full-dimensional feature set performance was echoed by dimensionally reduced feature set performance that included per-device 87.0% < %CDR < 99.7% and average cross-device %CDR ≈ 91.4% using only 18-of-291 features—the demonstrated %CDR > 90% with an approximate 92% reduction in the number of fingerprint features is sufficiently promising for small-scale network applications and warrants further consideration.

Data created at industrial sites through industrial internet of things devices are now being processed automatically or in real-time in the industrial structure, due to the application of artificial intelligence technology to industrial sites. However, the expenses of autonomous or real-time data processing and steady data processing (analysis, prediction, prescription, and implementation) necessitate a new processing method. We propose a blockchain-based industrial internet of things information reinforcement model in this work that may reliably ensure the integrity of industrial internet of things data produced at industrial locations. The proposed model processes industrial internet of things data that may occur at endpoints at industrial sites into the blockchain by processing data generated by the same industrial internet of things device independently. As a result, the IIoT data sent to the industrial internet of things server can be evaluated more readily, and production accuracy may be enhanced. The proposed model optimizes industrial internet of things information linkage by stochastically reflecting the information based on attribute value frequency. By dynamically aggregating the related data of industrial internet of things information acquired as a seed through hierarchical subnets, the proposed model increases stability and accuracy. Furthermore, the proposed model may be used to enhance an organizations' operational efficiency (consulting and training, for example) and strategic decision-making by utilizing fundamental knowledge about items produced at industrial locations. Furthermore, the proposed model allows for information sharing and system connectivity between industrial locations, allowing for close collaboration between industrial internet of things features. As a result of the performance evaluation, the proposed model included an industrial internet of things sensor to the blockchain, eliminating the need for an extra function in the manufacturing process and reducing the time required to validate the integrity of industrial internet of things data. In addition, as a result of analyzing industrial internet of things data by an algorithm according to the number of simulated clouds, the accuracy of industrial internet of things information was improved by 2.5% to 3%, on average.

IoT applications rely strongly on the performance of wireless communication networks. There is a wide variety of wireless IoT technologies and choosing one over another depends on the specific use case requirements-be they technical, implementation-related or functional factors. Among the technical factors, latency, error rate and stability are the main parameters that affect communication reliability. In this work, we present the design, development and validation of a Universal Testbed to experimentally measure these parameters, abstracting them from the wireless IoT technology protocols and hardware platforms. The Testbed setup, which is based on a Raspberry Pi 4, only requires the IoT device under test to have digital inputs. We evaluate the Testbed's accuracy with a temporal characterisation-accumulated response delay-showing an error less than 290 µs, leading to a relative error around 3% for the latencies of most IoT wireless technologies, the latencies of which are usually on the order of tens of milliseconds. Finally, we validate the Testbed's performance by comparing the latency, error and stability measurements with those expected for the most common IoT wireless technologies: 6LoWPAN, LoRaWAN, Sigfox, Zigbee, Wi-Fi, BLE and NB-IoT.

The Routing Protocol for Low-power and Lossy Networks (RPL) is a popular routing layer protocol for multi-hop Wireless Sensor Networks (WSNs). However, typical RPL configurations are based on decade-old assumptions, leading to a mismatch with: (1) advances in wireless hardware; and (2) growing wireless contention. To soften the impact of external stressors (i.e., jamming and interference), we extended RPL to exploit the capabilities of modern multi-interfaced wireless devices. More specifically, our main contribution is the design, development, and evaluation of a novel RPL Objective Function (OF) which, through simulations, is compared to traditional single-interface approaches and a state-of-the-art multi-interface approach. We examine two scenarios, with and without the injection of jamming, respectively. Our proposed OF is shown to outperform, or otherwise perform similar to, all alternatives considered. In normal conditions, it auto-selects the best interface whilst incurring negligible protocol overhead. In our jamming simulations, it provides stable end-to-end delivery ratios exceeding 90%, whereas the closest alternative averages 65% and is considerably less stable. Given we have open-sourced our development codebase, our solution is an ideal candidate for adoption by RPL deployments that expect to suffer interference from competing technologies or are unable to select the best radio technology a priori.

MQTT is one of the most popular application-layer protocols used in the scope of the Internet-of-Things (IoT) and Industrial-Internet-of-Things (IIoT), given its suitability for resource-constrained embedded systems. However, MQTT Quality-of-Service policies do not support timeliness requirements, which is common in IIoT. The literature reports several research works that address this limitation, but they are limited in scope (e.g., improvements in the broker's internal operation, control of the publisher's data rate, and path optimizations). Conversely, this paper presents a comprehensive architectural approach, proposing a set of extensions to the MQTT protocol that allow applications to explicitly specify real-time requirements and instantiate corresponding network reservations to enforce the desired temporal behavior. Such reservations are enforced via Software Defined Networking, specifically the OpenFlow protocol, but other protocols that allow bandwidth reservations, e.g., TSN, can also be used. This paper presents the proposed system architecture together with extensive emulation and implementation results that validate the feasibility of the approach, showing that time-sensitive MQTT traffic can be effectively segregated and prioritized to meet application-defined real-time requirements. Using several combinations of network topologies and load levels and comparing to the absence of the proposed real-time mechanisms, both average and worst-case latencies of the time-sensitive traffic decreased to approximately half, while for the normal traffic, they increased by approximately 10%.

Rapid development of smart manufacturing techniques in recent years is influencing production facilities. Factories must both keep up with smart technologies as well as upskill their workforce to remain competitive. One of the recent concerns is how businesses can contribute to environmental sustainability and how to reduce operating costs. In this article authors present a method of measuring gas waste using Industrial Internet of Things (IIoT) sensors and open-source solutions utilised on a brownfield production asset. The article provides a result of an applied research initiative in a live manufacturing facility. The design followed the Reference Architectural Model for Industry 4.0 (RAMI 4.0) model to provide a coherent smart factory system. The presented solution's goal is to provide factory supervisors with information about gas waste which is generated during the production process. To achieve this an operational technology (OT) network was installed and Key Performance Indicators (KPIs) dashboards were designed. Based on the information provided by the system, the business can be more aware of the production environment and can improve its efficiency.

Digital certificates are regarded as the most secure and scalable way of implementing authentication services in the Internet today. They are used by most popular security protocols, including Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS). The lifecycle management of digital certificates relies on centralized Certification Authority (CA)-based Public Key Infrastructures (PKIs). However, the implementation of PKIs and certificate lifecycle management procedures in Industrial Internet of Things (IIoT) environments presents some challenges, mainly due to the high resource consumption that they imply and the lack of trust in the centralized CAs. This paper identifies and describes the main challenges to implement certificate-based public key cryptography in IIoT environments and it surveys the alternative approaches proposed so far in the literature to address these challenges. Most proposals rely on the introduction of a Trusted Third Party to aid the IIoT devices in tasks that exceed their capacity. The proposed alternatives are complementary and their application depends on the specific challenge to solve, the application scenario, and the capacities of the involved IIoT devices. This paper revisits all these alternatives in light of industrial communication models, identifying their strengths and weaknesses, and providing an in-depth comparative analysis.

In industrial wireless sensors networks (IWSNs), the sensor lifetime predictability is critical for ensuring continuous system availability, cost efficiency and suitability for safety applications. When deployed in a real-world dynamic and centralised network, the sensor lifetime is highly dependent on the network topology, deployment configuration and application requirements. (In the absence of an energy-aware mechanism, there is no guarantee for the sensor lifetime). This research defines a conceptual model for enhancing the energy predictability and efficiency of IWSNs. A particularization of this model is the predictive energy-aware routing (PEAR) solution that assures network lifetime predictability through energy-aware routing, energy balancing and profiling. The PEAR solution considers the requirements and constraints of the industrial ISA100.11a communication standard and the VR950 IIoT Gateway hardware platform. The results demonstrate the PEAR ability to ensure predictable energy consumption for one or multiple network clusters. The PEAR solution is capable of intracluster energy balancing, reducing the overconsumption 10.4 times after 210 routing changes as well as intercluster energy balancing, increasing the cluster lifetime 2.3 times on average and up to 3.2 times, while reducing the average consumption by 23.6%. The PEAR solution validates the feasibility and effectiveness of the energy-aware conceptual indicating its suitability within IWSNs having real world applications and requirements.

The groundbreaking transformations triggered by the Industry 4.0 paradigm have dramatically reshaped the requirements for control and communication systems within the factory systems of the future. The aforementioned technological revolution strongly affects industrial smart and distributed measurement systems as well, pointing to ever more integrated and intelligent equipment devoted to derive accurate measurements. Moreover, as factory automation uses ever wider and complex smart distributed measurement systems, the well-known Internet of Things (IoT) paradigm finds its viability also in the industrial context, namely Industrial IoT (IIoT). In this context, communication networks and protocols play a key role, directly impacting on the measurement accuracy, causality, reliability and safety. The requirements coming both from Industry 4.0 and the IIoT, such as the coexistence of time-sensitive and best effort traffic, the need for enhanced horizontal and vertical integration, and interoperability between Information Technology (IT) and Operational Technology (OT), fostered the development of enhanced communication subsystems. Indeed, established technologies, such as Ethernet and Wi-Fi, widespread in the consumer and office fields, are intrinsically non-deterministic and unable to support critical traffic. In the last years, the IEEE 802.1 Working Group defined an extensive set of standards, comprehensively known as Time Sensitive Networking (TSN), aiming at reshaping the Ethernet standard to support for time-, mission- and safety-critical traffic. In this paper, a comprehensive overview of the TSN Working Group standardization activity is provided, while contextualizing TSN within the complex existing industrial technological panorama, particularly focusing on industrial distributed measurement systems. In particular, this paper has to be considered a technical review of the most important features of TSN, while underlining its applicability to the measurement field. Furthermore, the adoption of TSN within the Wi-Fi technology is addressed in the last part of the survey, since wireless communication represents an appealing opportunity in the industrial measurement context. In this respect, a test case is presented, to point out the need for wirelessly connected sensors networks. In particular, by reviewing some literature contributions it has been possible to show how wireless technologies offer the flexibility necessary to support advanced mobile IIoT applications.

There is no doubt that new technology has become one of the crucial parts of most people's lives around the world. By and large, in this era, the Internet and the Internet of Things (IoT) have become the most indispensable parts of our lives. Recently, IoT technologies have been regarded as the most broadly used tools among other technologies. The tools and the facilities of IoT technologies within the marketplace are part of Industry 4.0. The marketplace is too regarded as a new area that can be used with IoT technologies. One of the main purposes of this paper is to highlight using IoT technologies in Industry 4.0, and the Industrial Internet of Things (IIoT) is another feature revised. This paper focuses on the value of the IoT in the industrial domain in general; it reviews the IoT and focuses on its benefits and drawbacks, and presents some of the IoT applications, such as in transportation and healthcare. In addition, the trends and facts that are related to the IoT technologies on the marketplace are reviewed. Finally, the role of IoT in telemedicine and healthcare and the benefits of IoT technologies for COVID-19 are presented as well.

Currently, the concept of Industry 4.0 is well known; however, it is extremely complex, as it is constantly evolving and innovating. It includes the participation of many disciplines and areas of knowledge as well as the integration of many technologies, both mature and emerging, but working in collaboration and relying on their study and implementation under the novel criteria of Cyber-Physical Systems. This study starts with an exhaustive search for updated scientific information of which a bibliometric analysis is carried out with results presented in different tables and graphs. Subsequently, based on the qualitative analysis of the references, we present two proposals for the schematic analysis of Industry 4.0 that will help academia and companies to support digital transformation studies. The results will allow us to perform a simple alternative analysis of Industry 4.0 to understand the functions and scope of the integrating technologies to achieve a better collaboration of each area of knowledge and each professional, considering the potential and limitations of each one, supporting the planning of an appropriate strategy, especially in the management of human resources, for the successful execution of the digital transformation of the industry.

LoRaWAN has gained significant attention for Internet-of-Things (IOT) applications due to its low power consumption and long range potential for data transmission. While there is a significant body of work assessing LoRA coverage and data transmission characteristics, there is a lack of data available about commercially available LoRa prototyping boards and their power consumption, in relation to their features. It is currently difficult to estimate the power consumption of a LoRa module operating under different transmission profiles, due to a lack of manufacturer data available. In this study, power testing has been carried out on physical hardware and significant variation was found in the power consumption of competing boards, all marketed as "extremely low power". In this paper, testing results are presented alongside an experimentally-derived power model for the lowest power LoRa module, and power requirements are compared to firmware settings. The power analysis adds to existing work showing trends in data-rate and transmission power settings effects on electrical power consumption. The model's accuracy is experimentally verified and shows acceptable agreement to estimated values. Finally, applications for the model are presented by way of a hypothetical scenario and calculations performed in order to estimate battery life and energy consumption for varying data transmission intervals.

Most smart meters are connected and powered by the electric mains, requiring the service interruption and qualified personnel for their installation. Wireless technologies and energy harvesting techniques have been proved as alternatives for communications and power supply, respectively. In this work, we analyse the energy consumption of the most used IoT wireless technologies nowadays: Sigfox, LoRaWAN, NB-IoT, Wi-Fi, BLE. Smart meters' energy consumption accounts for metering, standby and communication processes. Experimental measurements show that communication consumption may vary upon the specific characteristics of each wireless communication technology-payload, connection establishment, transmission time. Results show that the selection of a specific technology will depend on the application requirements (message payload, metering period) and location constraints (communication range, infrastructure availability). Besides, we compare the performance of the most suitable energy harvesting (EH) techniques for smart meters: photovoltaic (PV), radiofrequency (RF) and magnetic induction (MIEH). Thus, EH technique selection will depend on the availability of each source at the smart meter's location. The most appropriate combination of IoT wireless technology and EH technique must be selected accordingly to the very use case requirements and constraints.

The possibility of understanding the dynamics of human mobility and sociality creates the opportunity to re-design the way data are collected by exploiting the crowd. We survey the last decade of experimentation and research in the field of mobile CrowdSensing, a paradigm centred on users' devices as the primary source for collecting data from urban areas. To this purpose, we report the methodologies aimed at building information about users' mobility and sociality in the form of ties among users and communities of users. We present two methodologies to identify communities: spatial and co-location-based. We also discuss some perspectives about the future of mobile CrowdSensing and its impact on four investigation areas: contact tracing, edge-based MCS architectures, digitalization in Industry 5.0 and community detection algorithms.

Internet of Things (IoT) can help to pave the way to the circular economy and to a more sustainable world by enabling the digitalization of many operations and processes, such as water distribution, preventive maintenance, or smart manufacturing. Paradoxically, IoT technologies and paradigms such as edge computing, although they have a huge potential for the digital transition towards sustainability, they are not yet contributing to the sustainable development of the IoT sector itself. In fact, such a sector has a significant carbon footprint due to the use of scarce raw materials and its energy consumption in manufacturing, operating, and recycling processes. To tackle these issues, the Green IoT (G-IoT) paradigm has emerged as a research area to reduce such carbon footprint; however, its sustainable vision collides directly with the advent of Edge Artificial Intelligence (Edge AI), which imposes the consumption of additional energy. This article deals with this problem by exploring the different aspects that impact the design and development of Edge-AI G-IoT systems. Moreover, it presents a practical Industry 5.0 use case that illustrates the different concepts analyzed throughout the article. Specifically, the proposed scenario consists in an Industry 5.0 smart workshop that looks for improving operator safety and operation tracking. Such an application case makes use of a mist computing architecture composed of AI-enabled IoT nodes. After describing the application case, it is evaluated its energy consumption and it is analyzed the impact on the carbon footprint that it may have on different countries. Overall, this article provides guidelines that will help future developers to face the challenges that will arise when creating the next generation of Edge-AI G-IoT systems.

Security is the main challenge of the Modbus IIoT protocol. The systems designed to provide security involve solutions that manage identity based on a centralized approach by introducing a single point of failure and with an ad hoc model for an organization, which handicaps the solution scalability. Our manuscript proposes a solution based on self-sovereign identity over hyperledger fabric blockchain, promoting a decentralized identity from which both authentication and authorization are performed on-chain. The implementation of the system promotes not only Modbus security, but also aims to ensure the simplicity, compatibility and interoperability claimed by Modbus.

IoT-based measurement systems for manufacturing have been widely implemented. As components that can be implemented at low cost, BLE beacons have been used in several systems developed in previous research. In this work, we focus on the Kanban system, which is a measure used in manufacturing strategy. The Kanban system emphasizes inventory management and is used to produce only required amounts. In the Kanban system, the Kanban cards are rotated through the factory along with the products, and when the products change to a different process route, the Kanban card is removed from the products and the products are assigned to another Kanban. For this reason, a single Kanban cannot trace products from plan to completion. In this work, we propose a system that uses a Bluetooth low energy (BLE) beacon to connect Kanbans in different routes but assigned to the same products. The proposed method estimates the beacon status of whether the Kanban is inside or outside a postbox, which can then be computed by a micro controller at low computational cost. In addition, the system connects the Kanbans using the beacons as paired connection targets. In an experiment, we confirmed that the system connected 70% of the beacons accurately. We also confirmed that the system could connect the Kanbans at a small implementation cost.

The Industrial Internet of Things (IIoT) could enhance automation and analytics in industrial environments. Despite the promising benefits of IIoT, securely managing software updates is a challenging problem for those critical applications. This is due to at least the intrinsic lack of software protection mechanisms in legacy industrial systems. In this paper, to address the challenges in building a secure software supply chain for industrial environments, we propose a new approach that leverages distributed watchdogs with blockchain systems in protecting software supply chains. For this purpose, we bind every entity with a unique identity in the blockchain and employ the blockchain as a delegated authenticator by mapping every reporting action to a non-fungible token transfer. Moreover, we present a detailed specification to clearly define the behavior of systems and to apply model checking.

Today, ensuring work safety is considered to be one of the top priorities for various industries. Workplace injuries, illnesses, and deaths often entail substantial production and financial losses, governmental checks, series of dismissals, and loss of reputation. Wearable devices are one of the technologies that flourished with the fourth industrial revolution or Industry 4.0, allowing employers to monitor and maintain safety at workplaces. The purpose of this article is to systematize knowledge in the field of industrial wearables' safety to assess the relevance of their use in enterprises as the technology maintaining occupational safety, to correlate the benefits and costs of their implementation, and, by identifying research gaps, to outline promising directions for future work in this area. We categorize industrial wearable functions into four classes (monitoring, supporting, training, and tracking) and provide a classification of the metrics collected by wearables to better understand the potential role of wearable technology in preserving workplace safety. Furthermore, we discuss key communication technologies and localization techniques utilized in wearable-based work safety solutions. Finally, we analyze the main challenges that need to be addressed to further enable and support the use of wearable devices for industrial work safety.

The certificate authority, a trusted entity, issues digital certificates which contain identity credentials to help Industrial Internet of Things (IIoT) devices to represent their authenticity in a secure means. The crucial challenge of a digital certificate is to how design a secure certification authority management system that can counteract cyberattacks on the IIoT network. Moreover, current IIoT systems are not capable of implementing complex mathematical operations due to their constrained power capacity and processing capability. This paper proposes an effective, secure symmetric cryptographic mechanism (ESSC) based on the certificate authority management and Elliptic Curve Diffie Hellman (ECDH) to share a digital certificate among IIoT devices. The proposed certificate authority is used to securely exchange the shared secret key and to resolve the problem of spoofing attacks that may be used to impersonate the identity of the certificate authority. Also, ESSC uses the shared secret key to encrypt the sensitive data during transmission through the insecure communication channel. This research studies the adversary model for ESSC on IIoT and analyzes the cybersecurity of ESSC in the random oracle model. The findings that result from the experiments show that ESSC outperforms the baseline in terms of communication, computation, and storage costs. ESSC thus provides an adequate lightweight digital certificate management and cryptographic scheme which can help in the detection and prevention of several cyberattacks that can harm IIoT networks.

The next-generation technologies enabled by the industry 4.0 revolution put immense pressure on traditional ISA95 compliant manufacturing systems to evolve into smart manufacturing systems. Unfortunately, the transformation of old to new manufacturing technologies is a slow process. Therefore, the manufacturing industry is currently in a situation that the legacy and modern manufacturing systems share the same factory environment. This heterogeneous ecosystem leads to challenges in systems scalability, interoperability, information security, and data quality domains. Our former research effort concluded that blockchain technology has promising features to address these challenges. Moreover, our systematic assessment revealed that most of the ISA95 enterprise functions are suitable for applying blockchain technology. However, no blockchain reference architecture explicitly focuses on the ISA95 compliant traditional and smart manufacturing systems available in the literature. This research aims to fill the gap by first methodically specifying the design requirements and then meticulously elaborating on how the reference architecture components fulfill the design requirements.

Maintenance is one of the most important aspects in industrial and production environments. Predictive maintenance is an approach that aims to schedule maintenance tasks based on historical data in order to avoid machine failures and reduce the costs due to unnecessary maintenance actions. Approaches for the implementation of a maintenance solution often differ depending on the kind of data to be analyzed and on the techniques and models adopted for the failure forecasts and for maintenance decision-making. Nowadays, Industry 4.0 introduces a flexible and adaptable manufacturing concept to satisfy a market requiring an increasing demand for customization. The adoption of vendor-specific solutions for predictive maintenance and the heterogeneity of technologies adopted in the brownfield for the condition monitoring of machinery reduce the flexibility and interoperability required by Industry 4.0. In this paper a novel approach for the definition of a generic and technology-independent model for predictive maintenance is presented. Such model leverages on the concept of the Reference Architecture Model for Industry (RAMI) 4.0 Asset Administration Shell, as a means to achieve interoperability between different devices and to implement generic functionalities for predictive maintenance.

The proliferation of the Internet of Things (IoT) caused new application needs to emerge as rapid response ability is missing in the current IoT end-devices. Therefore, Fog Computing has been proposed to be an edge component for the IoT networks as a remedy to this problem. In recent times, cyber-attacks are on the rise, especially towards infrastructure-less networks, such as IoT. Many botnet attack variants (Mirai, Torii, etc.) have shown that the tiny microdevices at the lower spectrum of the network are becoming a valued participant of a botnet, for further executing more sophisticated attacks against infrastructural networks. As such, the fog devices also need to be secured against cyber-attacks, not only software-wise, but also from hardware alterations and manipulations. Hence, this article first highlights the importance and benefits of fog computing for IoT networks, then investigates the means of providing hardware security to these devices with an enriched literature review, including but not limited to Hardware Security Module, Physically Unclonable Function, System on a Chip, and Tamper Resistant Memory.

The Industry 4.0 paradigm, since its initial conception in Germany in 2011, has extended its scope and adoption to a broader set of technologies. It is being considered as the most vital mechanism in the production systems lifecycle. It is the key element in the digital transformation of manufacturing industry all over the world. This scenario imposes a set of major unprecedented challenges which require to be overcome. In order to enable integration in horizontal, vertical, and end-to-end formats, one of the most critical aspects of this digital transformation process consists of effectively coupling digital integrated service/products business models with additive manufacturing processes. This integration is based upon advanced AI-based tools for decentralized decision-making and for secure and trusted data sharing in the global value. This paper presents the FASTEN IIoT Platform, which targets to provide a flexible, configurable, and open solution. The platform acts as an interface between the shop floor and the industry 4.0 advanced applications and solutions. Examples of these efforts comprise management, forecasting, optimization, and simulation, by harmonizing the heterogeneous characteristics of the data sources involved while meeting real-time requirements.

In this paper, we propose a methodology to use the received signal strength indicator (RSSI) available by the protocol stack of an installed Wireless Sensor Network (WSN) at an electric-power-system environment (EPS) as a tool for obtaining the characteristic of its communication channel. Thereby, it is possible to optimize the settings and configuration of the network after its deployment, which is usually run empirically without any previous knowledge of the channel. A study case of a hydroelectric power plant is presented, where measurements recorded over a two-month period were analyzed and treated to obtain the large-scale characteristics of the radiofrequency channel at 2.4 GHz. In addition, we showed that instantaneous RSSI data can also be used to detect specific issues in the network, such as repetitive patterns in the transmitted power level of the nodes, and information about its environment, such as the presence of external sources of electromagnetic interference. As a result, we demonstrate the practical use of the RSSI long-term data generated by the WSN for its own performance optimization and the detection of particular events in an EPS or any similar industrial environment.

The Industrial Internet of Things (IIoT) is of great significance to the improvement of industrial efficiency and quality, and to reduce industrial costs and resources. However, there are few openly-reported practical project applications based on the IIoT up to now. For legacy automation devices in traditional industry, it is especially challenging to realize the upgrading of industrial automation adopting the IIoT technology with less investment. Based on the practical engineering experience, this paper introduces the automation renovation of a sewage treatment plant. The legacy automation devices are upgraded by the central controller of a STM32 processor (Produced by STMicroelectronics company, located in Geneva, Switzerland), and the WeChatApplet (Developed by Tencent company, located in Shenzhen, China) is used as the extended host computer. A set of remote monitoring and control systems of sewage treatment based on the IIoT is built to realize the wide-area monitoring and control of sewage treatment. The paper describes the field hardware system, wide-area monitoring and control application program, management cloud platform and security technologies in detail. The actual operation results show that the monitoring system has the requirements of high accuracy, good real-time performance, reliable operation and low cost.

In the near future, value streams associated with Industry 4.0 will be formed by interconnected cyber-physical elements forming complex networks that generate huge amounts of data in real time. The success or failure of industry leaders interested in the continuous improvement of lean management systems in this context is determined by their ability to recognize behavioral patterns in these big data structured within non-Euclidean domains, such as these dynamic sociotechnical complex networks. We assume that artificial intelligence in general and deep learning in particular may be able to help find useful patterns of behavior in 4.0 industrial environments in the lean management of cyber-physical systems. However, although these technologies have meant a paradigm shift in the resolution of complex problems in the past, the traditional methods of deep learning, focused on image or video analysis, both with regular structures, are not able to help in this specific field. This is why this work focuses on proposing geometric deep lean learning, a mathematical methodology that describes deep-lean-learning operations such as convolution and pooling on cyber-physical Industry 4.0 graphs. Geometric deep lean learning is expected to positively support sustainable organizational growth because customers and suppliers ought to be able to reach new levels of transparency and traceability on the quality and efficiency of processes that generate new business for both, hence generating new products, services, and cooperation opportunities in a cyber-physical environment.

While there is a wide range of approaches to monitor industrial machinery through their static components, rotating components are usually harder to monitor, since sensors are difficult to be mounted on them and continuously read during operation. However, the characteristics of rotating components may provide useful information about the machine condition to be included in monitoring algorithms, specially for long-term data analysis. In this work, wireless vibration monitoring of rotating machine parts is investigated using surface acoustic wave (SAW) radio frequency identification (RFID) tags coupled with sensors. The proposed augmented transponder solution, combined with low-latency interrogation and signal processing, enables real-time identification and wideband vibration sensing. On top of that, a multi-channel interrogation approach is used to compensate motion effects. This approach enhances the signal-to-noise ratio of low-power high-frequency components present on the vibration signatures and enables discriminant information extraction from rotating machine parts. Final feasibility is evaluated with induction motors and vibration measurements on rotating shafts are verified. In addition, a condition classification algorithm is implemented in an experimental setup based on different motor states. The results of this work open the possibility to feed predictive maintenance algorithms using new features extracted in real-time from wideband vibration measurements on rotating components.

Industrial Control Systems (ICS) and Supervisory Control systems and Data Acquisition (SCADA) networks implement industrial communication protocols to enable their operations. Modbus is an application protocol that allows communication between millions of automation devices. Unfortunately, Modbus lacks basic security mechanisms, and this leads to multiple vulnerabilities, due to both design and implementation. This issue enables certain types of attacks, for example, man in the middle attacks, eavesdropping attacks, and replay attack. The exploitation of such flaws may greatly influence companies and the general population, especially for attacks targeting critical infrastructural assets, such as power plants, water distribution and railway transportation systems. In order to provide security mechanisms to the protocol, the Modbus organization released security specifications, which provide robust protection through the blending of Transport Layer Security (TLS) with the traditional Modbus protocol. TLS will encapsulate Modbus packets to provide both authentication and message-integrity protection. The security features leverage X.509v3 digital certificates for authentication of the server and client. From the security specifications, this study addresses the security problems of the Modbus protocol, proposing a new secure version of a role-based access control model (RBAC), in order to authorize both the client on the server, as well as the Modbus frame. This model is divided into an authorization process via roles, which is inserted as an arbitrary extension in the certificate X.509v3 and the message authorization via unit id, a unique identifier used to authorize the Modbus frame. Our proposal is evaluated through two approaches: A security analysis and a performance analysis. The security analysis involves verifying the protocol's resistance to different types of attacks, as well as that certain pillars of cybersecurity, such as integrity and confidentiality, are not compromised. Finally, our performance analysis involves deploying our design over a testnet built on GNS3. This testnet has been designed based on an industrial security standard, such as IEC-62443, which divides the industrial network into levels. Then both the client and the server are deployed over this network in order to verify the feasibility of the proposal. For this purpose, different latencies measurements in industrial environments are used as a benchmark, which are matched against the latencies in our proposal for different cipher suites., Competing Interests: The authors declare no conflict of interest.

The Industrial Internet of Things (IIoT) is having an ever greater impact on industrial processes and the manufacturing sector, due the capabilities of massive data collection and interoperability with plant processes, key elements that are focused on the implementation of Industry 4.0. Wireless Sensor Networks (WSN) are one of the enabling technologies of the IIoT, due its self-configuration and self-repair capabilities to deploy ad-hoc networks. High levels of robustness and reliability, which are necessary in industrial environments, can be achieved by using the Time-Slotted Channel Hopping (TSCH) medium access the mechanism of the IEEE 802.15.4e protocol, penalizing other features, such as network connection and formation times, given that a new node does not know, a priori, the scheduling used by the network. This article proposes a new beacon advertising approach for a fast synchronization for networks under the TSCH-Medium Access Control (MAC) layer and Routing Protocol for Low-Power and Lossy Networks (RPL). This new method makes it possible to speed up the connection times of new nodes in an opportunistic way, while reducing the consumption and advertising traffic generated by the network.