Search

Abstract As lanthanum oxide (La 2 O 3) has a large bandgap, it exhibits excellent optical properties. In this work, La 2 O 3 thin films are prepared by the sol-gel method from a lanthanum chloride (LaCl 3) precursor, on quartz and sapphire (0001) substrates. The effect of the annealing temperature (400–800 °C) on the optical properties of the La 2 O 3 films is investigated. The structure and optical properties are analyzed by X-ray diffraction, atomic force microscopy, scanning electronic microscopy, X-ray photoemission spectroscopy, Raman spectroscopy, ultraviolet (UV)–visible spectroscopy, Fourier transform infrared spectroscopy, and infrared variable angle spectroscopic ellipsometry. Results indicate that with an annealing temperature of ~600 °C, the roughness and optical properties of La 2 O 3 films can be significantly improved. Highlights • La 2 O 3 thin films are prepared by sol-gel method on quartz and sapphire substrates. • Effect of annealing temperature on their optical properties is investigated. • Results indicate that the best annealing temperature is around 600 °C. • The roughness and optical properties of films are significantly improved. [ABSTRACT FROM AUTHOR]

Abstract The hydrated magnesium-carbon films fabricated in this study demonstrated that grain growth and crystallinity modification by substrate temperature treatment crystallization produce films with fewer internal imperfections. This results in high mobility of the solution-deposited hydrated magnesium-carbon electrical conductance, with a corresponding dramatic harmonious transmittance in the infrared range. An investigation of the hydrated magnesium-carbon films shows that the temperature treatment dramatically improves the electron mobility and decreases the carrier concentration, which in turn simultaneously increases the conductivity and transparency. The hydrated magnesium-carbon films exhibit a mobility of up to 85.2 cm2/(V·s) and the resistivity declines rapidly to 1.72 × 10−2 Ω·cm. The transmittance of the visible spectrum increased to 90%. Although the conductivity of hydrated magnesium-carbon films is not prominent comparing to the conventional and widely-used n-type TCO materials, e.g. ITO, the films also showed excellent optical properties, which can be attributed to their low bond energy, with the infrared transmittance of the films being greater than 70% for a plasma wavelength of approximately 10 μm. Graphical abstract Unlabelled Image Highlights • The hydrated magnesium-carbon films are the non-oxide-type transparent electronic material. • The plasma wavelength of hydrated magnesium-carbon films was approximate 10 μm. • Discussed the effects of the carrier concentration and mobility on the photoelectrical properties. • Studied on effects of the substrate temperature on the photoelectrical properties. [ABSTRACT FROM AUTHOR]

Abstract High-quality, transparent, conducting, p-type γ-CuI thin films are prepared via an innovative layer-by-layer procedure based on the traditional simple iodination of Cu films (referred to as the LBL-I method) at room temperature (RT). The structure, morphology, and optoelectronic properties of the γ-CuI are investigated as functions of the per layer thickness. The final thicknesses of LBL-I γ-CuI films are consistent with that in the film prepared by the traditional one-step method (TOS). X-ray diffraction analysis reveals that all the films are polycrystalline with the most dominant (111) direction of the zinc blende structure, indicating the facile and successful fabrication of γ-CuI. Compared with the TOS film, the LBL-I films display enhanced transmittance and mobility. The higher transmittance of >80% in the visible region of LBL-I films was attained due to the smaller root-mean-square roughness values of 23–28 nm. The 50 nm/ l LBL-I CuI films have mobility values of 6.9–9.4 cm2 V−1 s−1, and lower resistivity of 0.039–0.05 Ω cm, which assist studies on applications of γ-CuI thin films in transparent electronics. Highlights • High-quality electrooptical properties p-type γ-CuI thin films are prepared. • Innovative layer-by-layer approach based on Cu films iodination (LBL-I) is used. • LBL-I films show better transmittance and mobility than films prepared in one step. [ABSTRACT FROM AUTHOR]

Abstract In p-type γ -CuI thin films synthesized by the iodination of Cu layers with iodine vapor, a frosted-glass-like appearance with a rough surface is usually obtained, which makes it difficult to apply the γ -CuI films to transparent electronics. This paper proposes an innovative method for the preparation of highly transparent p-type γ -CuI films. A chemical reaction between Cu thin films and iodine vapor, combined with the layer-by-layer process at a temperature between room temperature and 120 °C are found to result in highly transparent polycrystalline γ -CuI films. The root-mean-square roughness values of the γ -CuI films prepared by this method are 8.5–21.2 nm, which are smaller than those for the γ - CuI films synthesized by the conventional method. The microstructure and optoelectronic properties of the γ-CuI thin films are sensitive to the temperature of iodine vapor. A high transmittance (80%) of the film obtained at an iodine vapor temperature of 80 °C has a low resistivity of 5 × 10−2 Ω cm and high mobility of 8.7 cm2/Vs. Moreover, a boosted figure of merit is realized due to the simultaneously low resistivity and high transparency: its value jumps from ∼488 to ∼1630 MΩ−1. Graphical abstract Unlabelled Image Highlights • A traditional iodination reaction method combined with the layer-by-layer process. • Simultaneously high transmittance and low resistivity. • A boosted figure of merit is realized. [ABSTRACT FROM AUTHOR]

This paper investigates the influence of deposition conditions on the properties of yttrium oxide thin films. The paper focuses on the texture, optical and mechanical properties. With this objective, a series of yttrium oxide thin films with different thicknesses were deposited by direct current (DC) unbalanced reactive magnetron sputtering at high and low pumping speed. By changing the oxygen flow, depositions were performed in the three characteristic deposition modes for reactive magnetron sputtering, i.e., metallic, transition and poisoned mode. By using an oxygen flow directed to the substrate, full oxidation of the samples, as shown by X-ray photoelectron spectroscopy (XPS), in the three modes is obtained. Crystallographic characterization by X-ray diffraction (XRD) shows that films crystallize in the cubic phase with a strong (222) out-of-plane orientation at low oxygen flow. As the oxygen flow increases a mixture of cubic and monoclinic phase is obtained. In poisoned mode, the films consist of the cubic phase with preferred (420) orientation. Scanning electron microscopy (SEM) cross sections show, with increasing oxygen flow, a loss of the columnar structure. As the oxygen flow rates increase through the metallic, transition, and the poisoned mode, the grain size becomes gradually smaller. An overview diagram of all experimental results uncovers that the textural changes are closely linked to the oxygen partial pressure rather than the oxygen flow. The optical properties of films were investigated by spectroscopic ellipsometry (SE). The films with a columnar structure demonstrate superior hardness and modulus as well as the high plasticity. [ABSTRACT FROM AUTHOR]