Search

The flashover failure and damage of polypropylene (PP) and polyester (PET) films under nanosecond current pulses were experimentally investigated. A nanosecond pulse current test platform was established to study the flashover characteristics, performance degradation, and structural damage of dielectric films under repeated nanosecond current pulses. The accumulation and emission of surface charge influenced by field distortion and trap distribution were analyzed to clarify the mechanism by which the flashover voltage increases linearly with gas pressure at low pressure and saturates at high pressure. The significant effects of pulse energy, gas pressure, and discharge gap on film damage behavior were investigated. The damage pattern of PP and PET films includes surface deformation, reduced flash-voltage tolerance, molecular chain breakage, and group shedding. The damage of PP films is manifested as fine furrows, while PET corresponds to mountainous bumps. With the increasing number of discharges, the breakdown voltage of PP films decreased significantly, while the flash tolerance performance of PET films was more stable. Under the conditions of high pulse current amplitude, small discharge gap, and low air pressure, the damage degree of the film intensifies, which is characterized by severe destruction to the molecular structure and a significant decrease in flashover withstand voltage. Polymer films, flashover, nanosecond current pulses; performance degradation; microstructural damage. [ABSTRACT FROM AUTHOR]

In this paper, the results of tests on a 0.76-TW linear transformer driver (LTD) module for Z-pinch research are presented for the first time. Ten LTD cavities, each generating a 1-MA/90-kV pulse on a matched load, were connected in series with a magnetically insulated voltage adder to drive the e-beam diode. Three inner stalks with different radii were tested, and the results indicate that the output parameters of the ten cavities are sensitive to the cathode radii. As an intermediate step, a high-current pulse with 832 kV/912 kA/130 ns was obtained on the e-beam diode. To date, this is the maximum power generated directly by a fast LTD with mega-ampere current output. [ABSTRACT FROM AUTHOR]

For typical Tesla transformers with open magnetic-core, a novel coaxial design of the primary side using a mechanically controlled spark gap is introduced to obtain a more compact configuration. The primary winding has several alternative ports to vary the current distribution by changing the position of the capacitor component, and the entire primary circuit is built inside the outer cylinder. For this new primary configuration, we estimate the series parameters and ohmic losses: Polypropylene film capacitors and combined metallized film capacitors are used in the verification tests, and the former capacitor exhibits a lower parasitic resistance below 10 mΩ. The ohmic losses caused by the windings and spark gap are also considered. The results of the experiments show that the voltage gain has an 8.2% drop when the parasitic resistance of C1 increased from 10 mΩ to 24 mΩ, and we deduce that the contact resistance of this primary structure can be limited to below 10 mΩ according to the circuit analysis results and the verification test. [ABSTRACT FROM AUTHOR]

In this paper, a 5 Terawatt, 5 MV, 1 MA pulsed power system based on vacuum magnetic insulation is simulated by the particle-in-cell (PIC) simulation method. The system consists of 50 100-kV linear transformer drive (LTD) cavities in series, using magnetically insulated induction voltage adder (MIVA) technology for pulsed power addition and transmission. The pulsed power formation and the vacuum power flow are simulated when the system works in self-limited flow and load-limited flow. When the pulsed power system isn’t connected to the load, the downstream magnetically insulated transmission line (MITL) works in the self-limited flow, the maximum of output current is 1.14 MA and the amplitude of voltage is 4.63 MV. The ratio of the electron current to the total current is 67.5%, when the output current reached the peak value. When the impedance of the load is 3.0 Ω, the downstream MITL works in the self-limited flow, the maximums of output current and the amplitude of voltage are 1.28 MA and 3.96 MV, and the ratio of the electron current to the total current is 11.7% when the output current reached the peak value. In addition, when the switches are triggered in synchronism with the passage of the pulse power flow, it effectively reduces the rise time of the pulse current. [ABSTRACT FROM AUTHOR]