Search

Liquid-phase exfoliation of few-layer graphene in Coca-Cola ® was performed by a kitchen blender for rapid preparation of strain/light/humidity sensitive ink. The advantages of Coca-Cola as an exfoliating medium have been identified from the low structural defect (I D /I G = 0.39) and, moderate carbon to oxygen ratio (C/O = 2.6) obtained by the resulting graphene. It is discovered that a deposition of graphene on photo paper allowed a facile fabrication of smart paper that is able to detect minor strain (0 – 2.0%) with GF of 18.7. Meanwhile, the multi-responsiveness of ink towards light/humidity had been validated from the 10 s response time after the exposure to stimulants with the maximum resulting curvature degree of 16° and 14° under light and humidity changes, respectively. Finally, it is shown that our actuator is able to vertically lift a load (545 mg) from its initial flat position upon irradiation of light (200 mW/cm2). [Display omitted] [ABSTRACT FROM AUTHOR]

In the process industry, the actuator has complex operating processes. Its steady working conditions are easy to change. Moreover, it is in a dynamic process for long periods of time. These phenomena reduce the accuracy and timeliness of many condition monitoring (CM) methods. In this paper, a fault detection mechanism considering the complex operating processes of the actuator is proposed. One of its main feature is that it can detect faults under steady state regardless of variable load changes. The other is that it has ability to detect faults during dynamic processes refusing the interference of nonlinearity and dynamic characteristics. Firstly, an actuator data model library based on historical data is established offline. Secondly, in the online situation, after the R indicator divides the testing data into steady state or dynamic, it is input into the model library to obtain a standard training set. Finally, the steady-state/dynamic fault detection module will determine whether a fault has occurred based on the testing data and the training set. Moreover, open-loop experiments based on the DAMADICS (Development and Application of Methods for Actuator Diagnosis in Industrial Control Systems) platform and closed-loop experiments based on the water tank system are designed. These experiments show that, compared with other methods, the proposed fault detection framework has better monitoring performance during complex operating processes of actuators. • A novel actuator fault detection method is proposed. • It can deal with various complex operating processes containing steady and dynamic state. • It contains two novel extended non-negative matrix factorization algorithms. • The presented mechanism is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

Highlights • An active heat sink with agitators, synthetic jets, and micro pin fins is introduced. • The active heat sink is a more efficient method than traditional fan-assisted systems. • The active heat sink reduced a thermal resistance by 48% from the baseline condition. • The micro pin fins are most efficient in reducing the system thermal resistance. Abstract Air-cooled heat sinks are widely used for electronics cooling. Active and passive cooling components can be added to enhance the performance of the air-cooled heat sinks. In this paper, piezoelectric translational agitators and synthetic jets are integrated as active cooling components while micro pin fins are adopted as a passive cooling scheme. The heat transfer performance of the active heat sink system that combines these active and passive cooling components along with a suction fan is experimentally investigated. The piezoelectric translational agitators installed within cooling channels are operating at 222 Hz ∼ 820 Hz with a peak-to-peak displacement of 1.0 mm ∼ 1.4 mm, depending on the attached carbon fiber blade type. The piezoelectric synthetic jet array provides impingement flow into the cooling channels with an inclined configuration, that has been successfully integrated into the system without interference with other components by using a wedge platform. The jet operates at 720 Hz with the jet velocity of up to 39 m/s. Micro pin fins are fabricated onto both surfaces of each heat sink channel walls by a double-sided microfabrication technique. They have diameter, height, and spacing of 500 μm, 250 μm, and 1500 μm, respectively. The experimental results indicate that the micro pin fins are most efficient among the employed active and passive cooling components, reducing thermal resistance up to 38%, compared to plain heat sink performance. The piezoelectric translational agitator reduces system thermal resistance by 22%, compared to the non-agitated condition, at the same through-flow rate. The synthetic jet shows weaker cooling capability in the setting tested, compared to enhancement by the agitator plates or pin fins. The active heat sink with the micro pin fins, agitators, and jets provides a thermal resistance of 0.064 °C/W at 70 CFM (33 L/sec) through-flow of air, about a 48% reduction from that of the non-agitated, plain heat sink under the same operating conditions. The results demonstrate how more effective the active heat sink system is compared to traditional air-cooled heat sinks. [ABSTRACT FROM AUTHOR]

In this paper, we propose a method for taking into account uncertainties of a micro-pump system using Shape Memory Alloy (SMA), based on the perturbation method. The proposed method is used to determine the thermo-mechanical response of a system. Comparisons with the mean value reference solution, illustrate the efficiency of the proposed method. The results are discussed in order to investigate the influence of the most influential parameters of the thermomechanical SMA model. The simulation results are obtained by the proposed method for static analysis with uncertainties.The perturbation method results are compared with the mean value reference solution. The results are discussed in order to investigate the influence of the Young's modulus E, the two transformations strain magnitude ɛ t r a c T and ɛ t r a c T F A , the martensite start M s and austenite finish A f temperatures and the stress reorientation F ε on the static response of a micro-pump system. [ABSTRACT FROM AUTHOR]

• A real-time hybrid testing based on shaking table and actuator is proposed for cable tray system. • The proposed method is validated by numerical simulations. • The proposed method is experimentally validated by one cable tray system. For precisely disclosing the seismic performance of cable tray systems, one novel Real-Time Hybrid Testing based on Shaking Table and Actuator (RTHT-STA) is proposed in this paper. In the proposed method, one shaking table is used to simulate the ground motion, and one servo-hydraulic actuator controlled with displacement mode is set up on the shaking table for truly simulating the transverse shear boundary conditions between the numerical substructure and the experimental substructure of cable tray systems. The advantage of the proposed method is accurately realizing the loading requirements of high-precision large deformation on cable tray systems. The effectiveness and accuracy of the proposed method are validated by numerical simulations and experimental tests. The experimental results show that the real-time hybrid testing system is stable and reliable. The correlation coefficients between the results of the proposed method and those of the traditional shaking table tests are higher up to 91.78%. The results indicate the effectiveness and the high accuracy of the proposed RTHT-STA for cable tray systems. The RTHT-STA provides an economical and precise investigation strategy for disclosing the seismic performance of cable tray systems and may have broad application prospects in the field of communication engineering and civil engineering. [ABSTRACT FROM AUTHOR]

In this paper, a novel actuator in the form of a Kagome truss composed of shape memory alloy (SMA) wires and common metallic wires is described. In the actuator, the SMA wires play dual roles as load supporters and actuating elements. The intersections between the SMA wires and between the SMA wires and the common metallic wires were joined by using shrinkable tubes, which induced the kinematically compatible buckling of the columns of SMA wires under compression, consequently enabling the large actuation displacement of up to 30% of the height with some sacrifice of the load capacity. An analytic solution was derived using the elementary mechanics of buckling and geometric relation of curved column, which gave fairly good estimation of the behavior of the Kagome actuator for the deformation and actuation stages, based on the behavior of a single SMA wire. The lightness and large actuation range of this actuator appear to be useful for practical applications. [ABSTRACT FROM AUTHOR]

A diffusion behavior of hydrogen in a hydrogen storage alloy is affected by not only hydrogen concentration but also the stress induced by hydrogen atom expanding the lattice of the alloy. The uphill diffusion in which hydrogen diffused against the concentration gradient due to the stress has been observed. Moreover, the fugacity of hydrogen in the alloy deviates from unity significantly even at low hydrogen concentration, which decreases the flux. In this paper, the effect of the stress and the diffusion coefficient variation with the concentration on hydrogen diffusion at low concentration was investigated using the finite element analysis. As a result, the variable diffusion coefficient model combined with the stress effect showed better agreement with the experimental result than Fick's diffusion models and the constant coefficient SID model. It was concluded that the effect should be considered even if the concentration is low. [ABSTRACT FROM AUTHOR]

This paper considers a thermal phase change actuator filled with a solid–liquid phase change material (PCM), in which its ceiling wall can be thermally activated to move as a result of the volumetric changes associated with thermally induced melting and freezing processes of the PCM contained. Specifically, the present study aims to explore experimentally the dynamic response characteristics of the actuator’s movable wall during the melting process of a paraffin (n-Octadecane) as the PCM filled in a rectangular container. Melting experiments for the phase change actuator heated laterally at various isothermal wall temperatures with the solid PCM filled at different initial subcooling temperatures below its melting point have been undertaken to examine the melting heat transfer characteristics as well as the displacement behavior of its movable wall. The experimental results obtained reveal clearly that the melting progress of the PCM within the actuator has a dominant bearing on the induced moving speed and thus the total displacement of its movable wall. Moreover, the subcooling condition for the solid PCM filled in the actuator during the melting process may give rise to significant time lag for its thermally driven response, hence increasing the total time required for the solid PCM to be fully melted. [ABSTRACT FROM AUTHOR]

This paper presents a novel thimble-shape haptic display for multi-mode tactile feedback at fingertips. The device has two special characteristics. Multi-mode feedback, i.e., static pressure, high-frequency vibration, and impact force, can be generated via a single actuator mechanism of a pneumatic chamber controlled by high-speed valves. Additionally, the actuator's softness makes this device a "feel-through" tactile display where the user simultaneously feels responses from a real object and synthetic feedback. This makes the device a fit for haptic augmented reality-based display where real and virtual touch feedback is merged into single feedback that haptically "augments" the real world. A layered combination of flexible and non-flexible silicone membrane surrounds the air- cavity for desired efficiency, and systematic valve control algorithms are developed for rich haptic effects. The experiments confirmed that the system generated a static force up to 7 N, acceleration magnitude up to 1.4 G, and frequency up to 250 Hz. The device exhibits two realistic tactile signals, i.e., virtual textures and button clicks, based on real signals and a physical surface that are augmented with two haptic signals.The user studies revealed that the participants found the virtually overlaid textures and buttons to be perceptually similar to their real counterparts. [ABSTRACT FROM AUTHOR]

At first a detailed fast shutter design was finalized for the ITER core charge exchange recombination spectroscopy (CXRS) diagnostic. The shutter has approximately 70 kg of mass and a length of 2.1 m. It operates in fractions of a second (0.7 s) protecting critical optical components against degradation and providing means of calibration for the optical system. The shutter structure is driven by a bidirectional frictionless helium actuator, with forces and axial strokes of 3.4 kN and 2 mm respectively. The shutter structure consists of: (a) two blades made of CuCrZr and stainless steel, calibration surfaces (currently Al 2 O 3 ) on the top and on the bottom a protective TZM (Mo–0.5Ti–0.08Zr) screens, (b) two arms interconnected that form one cooling circuit including the blades, (c) a bumper system to limit the arms movement, and (d) a support. A description of these components and their functions are given in this paper, followed by some issues, and their corresponding solutions or ongoing investigations, encountered during the design work. Detailed manufacturing drawings have been developed as the deliverable final product of this design stage, and are used in the prototyping phase which includes testing, numerical benchmarking, and validation of the shutter concept. [ABSTRACT FROM AUTHOR]

Soft actuators with large deformation and high stability in response to multi-stimuli are highly demanded in biomimetic applications. However, most of the present actuators driven by a single stimulus often exhibit low performance and high energy consumption. In this work, a sandwich structural soft actuator (MPDMS/MXene/PTFE) which possesses electrothermal/magnetic coupling actuation is fabricated by combining magnetic NdFeB/Polydimethylsiloxane (MPDMS) composite layer, MXene film, and PTFE tape together. Due to the large difference of thermal expansion coefficient between MPDMS film and PTFE tape, the soft actuator shows a wonderful electrothermal actuation and the bending deformation can reach to as high as 353° under a 3 V power supply. The excellent electrical conductivity of MXene component endows the sandwich film with good thermal management performance, thus the soft MPDMS/MXene/PTFE sandwich films can be applied in the thermal treatment of body and thermal imaging. Most importantly, the soft actuator also exhibits a typical magnetic biomimetic actuation and the programmable actuation performance of the dragonfly actuator can be demonstrated by both experiments and finite element simulations. Eventually, the electrothermal/magnetic coupling actuation is successfully applied in an intelligent crawling robot to overcome the traditional inchworm movement simulation. A dual-mode biomimetic soft actuator based on MPDMS/MXene/PTFE with excellent electrothermal and magnetic drive performance is developed. The soft actuator enables to prepare grippers for transferring objects and assemble the wings of a biomimetic dragonfly in a magnetic field. Finally, a crawling robot is developed to demonstrate the electrothermal/magnetic coupling actuation. [Display omitted] • The highlight of this work is: • The MPDMS/MXene/PTFE soft actuator presents both electrothermal and magneto-actuated deformation behaviors. • The soft actuator shows a wonderful electrothermal actuation and the bending deformation can reach to as high as 353° under a 3 V power supply. • The finite element analysis model can provide design guidance for the deformation process of bionic actuator with complex structure. • The soft actuator strategy presented in this paper is expected to be useful for the development of bionic intelligent actuators with multi-stimulus response. [ABSTRACT FROM AUTHOR]

[Display omitted] • One monolayer Janus bio-nanocomposite film with stimulus response is developed. • Janus structure and bonding intensity is obtained by incorporating nanocellulose into PVA. • Asymmetric structure, good mechanical properties, and water-resistance are realized. • Janus bio-nanocomposite film exhibits a smart and controllable responsiveness to salts. • Janus bio-nanocomposite film based actuators are controllably designed and explored. Stimuli-responsive materials have been increasingly explored to construct actuators and develop soft robots. Herein, one strategy via regulating lignin-containing cellulose nanofibrils (LCNF) distribution in PVA network followed by alkaline treatment (AT) and pre-stretching to fabricate bio-nanocomposite derived Janus films with stimulus response is proposed. LCNF/PVA-AT film displays obvious asymmetric structure, good mechanical properties, and water-resistance. Based on Janus structure and Hofmeister effect of PVA in salt solution, the applied pre-stretching treatment further enables the as-prepared LCNF/PVA-AT film with an excellently smart and controllable responsiveness to salt solutions. In addition, by adjusting some factors including length–width ratio of the film, salt type and concentration, the deformation degree and response/recovery time of LCNF/PVA-AT film and its based actuators can be controllably designed. The study will enrich the development of green, sustainable and biodegradable polymers derived Janus films, and expand their wide potential applications in multifunctional actuators. [ABSTRACT FROM AUTHOR]