Search

To meet the 2050 EU decarbonization goals, there is a need for new and innovative ideas to increase energy efficiency, which includes reducing the energy consumption of buildings and increasing the use of on-site renewable energy sources. One possible solution for achieving efficient thermal energy transition in the building sector is to assign new functionalities to the building envelope. The building envelope can function as a thermal energy storage system, which can help compensate for irregularities in solar energy availability. This can be accomplished by utilizing phase change materials as the energy storage medium in the building envelope. In this paper, two phase change materials with different melting temperatures of 21 °C and 28 °C are compared for their application in a dynamic solar building envelope. Both experimental and numerical studies were conducted within the scope of this study. The laboratory testing involved simulating the conditions of the four seasons through steady-state and dynamic experiments. The performance of the phase change materials was evaluated using a small-scale PASLINK test stand that imitates indoor and outdoor conditions. A numerical model of a small-scale building envelope was created using data from laboratory tests. The purpose of this model was to investigate how the tested phase change materials perform under different climate conditions. The experimental findings show that RT21HC is better at storing thermal energy in the PCM and releasing it into the indoor area than RT28HC. On the other hand, the numerical simulation results demonstrate that RT28HC has an advantage in terms of thermal storage capacity in climates found in Southern Europe, as it prevents overheating of the room. [ABSTRACT FROM AUTHOR]

Accounting for nearly 40% of final energy consumption, buildings are central to European energy policy. The Directive on Energy Performance of Buildings establishes a benchmarking system known as cost-optimality to set minimum energy performance requirements in new and existing buildings. This paper applies the cost-optimal methodology to an existing structure located in the Mediterranean area (Southern Italy). The building is composed of two units that have been considered for different uses: hotel and multi-residential. Several energy efficiency and renewable measures have been implemented both individually and as part of packages of measures. The cost-optimal solution has been identified as able to optimize energy consumption and costs from financial and macroeconomic perspectives. The first reference building (hotel use) shows a maximum reduction of primary energy and CO2 emission of about 42%, falling within the CasaClima energy class D, while the second reference building (residential use) achieves a value of 88% for primary energy and 85% for CO2 emissions, falling into class B. Thermal dispersions through the envelope can be limited using a suitable combination of insulating materials while a variety of technical variants are selected, such as VRF (variant refrigerant flow) systems, heat pumps with fan coils associated with controlled mechanical ventilation, solar thermal and photovoltaic. This paper illustrates the development of energy retrofit projects, in order to reach a balance between efficiency measures and costs for a building having two different uses, providing guidance to similar case studies related to a warm climate. [ABSTRACT FROM AUTHOR]

Due to the energy transformation in buildings, the proportions of energy consumption for heating, ventilation and domestic hot water preparation (DHW) have changed. The latter component can now play a significant role, not only in the context of the annual heat demand, but also in the context of selecting the peak power of the heat source. In this paper, the comparison of chosen methods for its calculation is presented. The results show that for contemporary residential buildings, the peak power for DHW preparation can achieve the same or higher value as the peak power for heating and ventilation. For this reason, nowadays the correct selection of the peak power of a heat source for DHW purposes becomes more important, especially if it uses renewable energy sources, because it affects its size and so the investment cost and economic efficiency. It is also indicated that in modern buildings, mainly accumulative systems with hot water storage tanks should be taken into account because they are less sensitive to design errors (wrongly selected peak value in the context of the uncertainty of hot water consumption) and because they result in acceptable value of peak power for DHW in comparison to heating and ventilation. [ABSTRACT FROM AUTHOR]

Around 30% of the European building stock was built before 1950, when no regulations about energy efficiency were in force. Since only a small part of them has been renovated by now, the energy performance of this building stock is on average quite poor, resulting in a significant impact on the energy balance of European countries, as confirmed by data published by ISTAT (Italian National Statistical Institute). However, energy retrofit in historic edifices is a quite demanding issue as any intervention must take into account the need to preserve existing building materials and appearances while also allowing reversibility and low invasiveness. As an example, in these buildings it is not possible to apply an ETICS (External Thermal Insulation Composite System), since this would alter the historic and architectural value of the façade. On the other hand, internal insulation would have the drawback of reducing the net useful floor area, which also implies a loss of economic value. Moreover, internal insulation may induce overheating risks and mold formation. In this paper, all these issues are investigated with reference to an existing historic building located in southern Italy, showing that a retrofit strategy aimed at energy savings and cost-effectiveness is still possible if suitable materials and solutions are adopted. [ABSTRACT FROM AUTHOR]

Greening structures attract worldwide attention because of their multidisciplinary benefits. Green roofs are considered one of the best ways to eliminate summer overheating, mitigate climate change, or reduce the urban heat island effect. The winter season and its impact on building energy consumption are often overlooked. Common standards do not take a green roof structure into consideration because of possible high water content in their layers. Additional roof layers may have a positive effect during the winter; they help reduce surface overcooling in cloudless winter nights. This paper analyses experimental measurements taken on two different extensive green roofs and compares the results with a single-ply roof (R) with a PVC membrane. Surface overcooling of the R due to radiation reaching up to 10 °C, whereas the green roof membrane is protected. The influence of thermal loss is not so important for the current climate in Central Europe, as the required U-values are lower than 0.1. The temperature difference is reduced from 17 °C on the membrane to 0.7 °C on the top of the concrete slab. The green roof is still advantageous, and the vegetation surface has better thermal stability. The advantage is clearly recognisable in the area of the condensation zone. The difference between these two extensive green roofs is very small in regard to the accuracy of the temperature sensors. The outcome showed the thermal loss reduction compared to the common flat roof; however, after analysis, it was more marginal than expected. [ABSTRACT FROM AUTHOR]

Building energy efficiency has grown strong in a context of soaring energy prices, especially in Europe. The use of energy-saving devices strongly influences its improvement, but in many cases, it is far from sufficient., especially if the energy comes from renewable sources with forced production. In the case of buildings, these are usually photovoltaic (PV) sources. For this reason, energy management systems (EMS) are becoming increasingly popular as they allow the increase in self-consumption and reduce the size of energy storage. This article presents analyses of historical energy consumption profiles in selected small- and medium-sized buildings powered by renewable energy sources. The implementation limitations of this type of systems, depending on the profile of the building, were identified and guidelines were presented to assess low-cost solutions dedicated to small buildings and considering the actual conditions of existing systems. Statistical analyzes were conducted for the energy demand profiles of 15 different buildings. The analyzes consisted of the preparation of box plots for each hour of working days and the calculation of the relative standard deviation (RSD) index for annual profiles of 60 min periods. The analyzes showed that the RSD index has low values for commercial buildings (e.g., hospital 7% and bank 15%) and very high values for residential buildings—even over 100%. On this basis, it can be concluded about the usefulness of energy profiles for demand forecasting. The novelty of the proposed method is to examine the possibility of using measurement data as data to forecast energy consumption based on statistical analysis, dedicated to low-cost EMS system solutions. [ABSTRACT FROM AUTHOR]

To achieve carbon neutrality in the EU, it is important to renovate the existing EU residential buildings for a higher building energy efficiency. This study examines the impacts of several novel renovation technologies on energy consumption, CO2 emissions and indoor climates in southern European residential buildings through building-level simulations. Three typical residential buildings in South Europe were chosen as the demo buildings to implement the novel technologies. The technologies were classified into passive, ventilation and generation packages, and then simulated independently under the intermittent and continuous heating schedules. Additionally, two final combinations of renovation technologies were also simulated to demonstrate the maximum energy and CO2 emissions reduction potential of the demo buildings. All novel retrofit technologies manifested obvious effects on the energy consumption and CO2 emissions. Nevertheless, the effects were significantly affected by the heating schedule. When the intermittent heating schedule was switched to the continuous heating schedule, the relative energy conservation and CO2 emissions reduction potential of the thermal insulation improvement measures (e.g., bio-aerogel thermal insulation) increased, while those of the generation measures (e.g., solar assisted heat pump) diminished. Renovation with the final combinations reduced the primary energy consumption by up to 66%, 74% and 65% in the continuously heated Greek, Portuguese and Spanish demo buildings, the corresponding CO2 emissions reductions of which were 65%, 75% and 74%, respectively. [ABSTRACT FROM AUTHOR]