Search

Methylammonium chloride (MACl) additive is almost irreplaceable in high‐performance formamidine perovskite photovoltaics. Nevertheless, Some of the problems that can arise from adding MACl are rarely mentioned. Herein, it is proposed for the first time that the addition of MACl would cause the non‐stoichiometric ratio in the perovskite film, resulting in the halogen vacancy. It is demonstrated that the non‐synchronous volatilization of methylamine cations and chloride ions leads to the formation of halogen vacancy defects. To solve this problem, the NH4HCOO is introduced into the perovskite precursor solution to passivate the halogen vacancy. The HCOO− ions have a strong force with lead ions and can fill the halogen vacancy defects. Consequently, the champion devices' power conversion efficiency (PCE) can be improved from 21.23% to 23.72% with negligible hysteresis. And the unencapsulated device can still retain >90% of the initial PCE even operating in N2 atmosphere for over 1200 h. This work illustrates another halogen defect source in the MACl‐assisted formamidine perovskite photovoltaics and provides a new route to obtain high‐performance perovskite solar cells. [ABSTRACT FROM AUTHOR]

We prepared ternary organic solar cells (OSCs) by incorporating the medium wavelength absorption polymer PSEHTT into the PM6:L8-BO binary system. The power conversion efficiency (PCE) is improved from 15.83% to 16.66%. Although the fill factor (FF) is slightly reduced, the short-circuit current density (JSC) and open-circuit voltage (VOC) are significantly increased at the same time. A small amount of PSEHTT has a broad absorption spectrum in the short wavelength region and has good compatibility with PM6, which is conducive to fine-tuning the photon collection and improving the JSC. In addition, the highest occupied molecular orbital (HOMO) energy level of PSEHTT is deeper than that of PM6, which broadens the optical bandgap. This study provides an effective method to fabricate high-performance ternary OSCs by using a lower concentration of PSEHTT with PM6 as a hybrid donor material, which ensures a better surface and bulk morphology, improves photon collection, and broadens the optical bandgap. [ABSTRACT FROM AUTHOR]

Abstract We describe a ternary photoactive layer based on PffBT4T-2OD as a donor with a blend of dihydronaphthyl-based C60 bisadduct (NCBA) and PC 71 BM as the acceptor. It offers ideal exciton dissociation, an ideal charge-carrier recombination and photovoltaic performance relationship, and improves the power-conversion efficiency (PCE) and stability of polymer solar cells (PSCs). NCBA has a broad visible-light absorption spectrum and shallower lowest unoccupied molecular orbital (LUMO) energy levels, which enhance exciton dissociation and charge-carrier transport and suppress charge-carrier recombination. This remarkably increases the photocurrent density and fill factor. An optimized PCE of 9.79% was achieved for the ternary PffBT4T-2OD:NCBA:PC 71 BM(1:0.24:0.96)-based PSCs. The mechanism was exciton dissociation at the PffBT4T-2OD/NCBA, PffBT4T-2OD:PC 71 BM, and NCBA/PC 71 BM interfaces. This simultaneously enhances the exciton-dissociation ratio and charge-carrier transport. Meanwhile, PSCs with 20% NCBA as third-component materials exhibit improved thermal stability and photo-stability leading to a lower ratio of PCE under long-time thermal-annealing and visible-light-illuminated treatment. This work indicates that NCBAs are third-component materials that significantly improve PSC performance. Highlights • Ternary PSCs were fabricated with NCBA as third component materials. • The ternary photoactive layer is weaken charge carrier recombination. • The improved exciton-dissociation at the donor–blend acceptor interface. • The enhanced photovoltaic performance, thermal stability and photo stability. [ABSTRACT FROM AUTHOR]

SnO 2 electron transport layers (ETLs) had an essential role in the n-i-p structure of perovskite solar cells. Improving the quality of the electron transport layer and enhancing interfacial contacts were key factors in the fabrication of high-performance perovskite solar cells. Therefore, a non-ionic polymeric polyacrylamide (PAM) modified SnO 2 colloidal solution with improved clustering of SnO 2 nanoparticles was presented to form a uniform and dense SnO 2 electron transport layer. The results demonstrated that no pinhole pores were found at the interface where the PAM-modified electron transport layer and the light absorbing layer came into contact, a structure that facilitated carrier transport and reduced carrier recombination at the interface location. Further beneficial effects were revealed by femtosecond Fs-TA measurements and trap of states (tDOS) analysis, where the carrier lifetime τ 2 decreased from 306.7 ps to 137.8 ps and the trap density of states of the film also decreased significantly. Correspondingly, the SnO 2 -PAM device exhibited an optimum efficiency of 21.61 %. Fantastic device stability was obtained due to the interaction of excellent contact at the SnO 2 /FAPbI 3 interface, and 85 % of the initial efficiency was maintained when placed in air for 1000 h for photo-aging tests, thereby improving the stability of FAPbI 3 grains. This method of improving the quality of tin oxide colloidal solutions provided a novel and simple way to prepare efficient perovskite solar cells. [ABSTRACT FROM AUTHOR]

The development of perovskite solar cells has improved rapidly. However, PSCs generally suffer from instability, due to the detrimental defects. Additive engineering is a favorable method for defect passivation. In this work, the linear pseudo-halogen salt, KSCN, is introduced into the MAPbI 3 perovskite film to improve the performance of PSC. The trap density of cells with SCN− is decreased significantly. The SCN− not only can fill halogen vacancies to reduce the halide-related defects, but also can interact with the uncoordinated Pb2+ via coordinate bond to stabilize perovskite lattice structure. Moreover, the performance of devices with other linear pseudo-halogen anions (OCN−, SeCN−) are also investigated. Due to the improved short circuit current density, the power conversion efficiency of devices increases from 18.02% (PVK) to 20.41% (PVK–SCN-), 19.53% (PVK–OCN-) and 19.23% (PVK–SeCN-), respectively. After introducing pseudo-halide anions, the devices showed robust stability under the ambient environment. [ABSTRACT FROM AUTHOR]

Organic-inorganic hybrid perovskite materials with distinctive optoelectronic properties have attracted much interest in the field of solar cells. As the light absorber, the quality of perovskite films is crucial to the performances of perovskite solar cells. Anti-solvent engineering seems to be an efficient method in preparing high-quality perovskite films, but mostly used anti-solvents are toxic, such as chlorobenzene (CB)， which is harmful to the environmental protection. In the present work, we used the green anti-solvent diethyl carbonate (DEC) instead of CB, demonstrated that the DEC engineered CH 3 NH 3 PbI 3 film exhibits improved morphology and crystallinity as well as reducing defects, which can be attributed to the interaction between DEC and the solvent dimethyl sulfoxide (DMSO). The DEC anti-solvent assisting yields efficient CH 3 NH 3 PbI 3 perovskite solar cells with a champion power conversion efficiency of 20.20% and a steady state efficiency of 86% over a period of 20 days of storage under ambient conditions. The present study provides a viable path way to design green and effective perovskite solar cells in the future. [Display omitted] • Developed a green solvent-assisted perovskite crystallization method. • Formed uniform and compact perovskite films with large grains. • High-quality perovskite films prepared by green anti-solvent diethyl carbonate. [ABSTRACT FROM AUTHOR]