Search

This paper presents an investigation of the underlying mechanism behind the interface charge barrier between oil and oil immersed paper. Two types of oils and two types of cellulose papers are selected in the study. The interface charges of the samples are measured by the pulsed electro-acoustic (PEA) method and the zeta potentials of different oil-paper combinations are also measured. The results show that the amount of interface charge changes with the type of oils and papers, and is much larger than the Maxwell-Wagner-Sillars (MWS) polarization charge. The difference in the amount of interface charges cannot be attributed to the difference in the conductivity and permittivity of the materials. It is suggested that the barrier for charge transport across the interface, which is formed due to the electric double layer, should be taken into consideration to explain the interface charge behavior in oil-paper insulation. [ABSTRACT FROM AUTHOR]

Oil-paper insulation of higher voltage winding and traction winding in on-board traction transformers frequently withstand large AC fluctuation voltages mainly combined with AC and inter-harmonic components. This paper presents the characteristics of partial discharge (PD) of oil-paper insulation under superimposed inter-harmonic AC voltages. The experimental results show that the addition of the inter-harmonic to the fundamental sinusoidal component results in variation of peak voltage and dv/dt along the phase. This superimposed inter-harmonic AC voltages has a significant impact on PD including partial discharge inception voltage (PDIV), breakdown voltage, PD repetition rate, and phase resolved partial discharge (PRPD). In addition, a dynamic characterization method of PD statistical parameters is proposed to determine the developing trend. The critical values and inflection points of PD are obtained. Besides, the theoretical mechanism is expounded to better interpret and understand the influence of inter-harmonic component on PD properties. These methods will provide the dynamic datasets and more information for insulation condition assessment of on-board traction transformer. [ABSTRACT FROM AUTHOR]

In this paper, the temporal space charge dynamics under both temperature and voltage polarity reversal of an epoxy resin impregnated crepe paper are characterized by pulsed electroacoustic method. It is found that the space charge injection and the interfacial traps located between the epoxy and paper plays an important role in determining the space charge dynamics. The results reveal that below 353 K, the calculated interfacial charge density is consistent with the Maxwell-Wagner (MW) model, while above 353 K, it is smaller than the measured value. The time constant during charging is much smaller than that predicted by the MW model and the space charge injection showed polarity effect, which leads to the interfacial charge densities under polarity poling voltage not being equal. It is proposed that the interfacial traps and space charge injection should be responsible for the observed space charge dynamics. [ABSTRACT FROM AUTHOR]

Transformer oil, insulating paper, high voltage direct current (HVDC) bushings and on-load tap changer (OLTC) are essential parts of converter transformers. When the power flow of the HVDC system is reversed or a sudden outrage occurs, the charge field will deform the dielectric internal electric field, thus easily leading to the occurrence of discharge or insulation damage. In this case, it is necessary to carry out the characterization of the oil?paper interface to avoid these consequences. This paper analyses the interface charge accumulation and dissipation characteristics of an oil?paper insulation system under DC and polarity reversal voltages. In this paper, induced electrification was used to charge the composite oil?paper insulation. The amplitude of DC and polarity reversal voltages applied in this paper was 4 kV, and paper with thicknesses of 0.08 and 0.13 mm was used. This research offers a theoretical exploration to optimize the transformer oil? paper insulation structure and prevent damage to its insulation systems. From the research on different layers and thicknesses of paper, it can be concluded that the decay is fast in the initial period and then becomes slower with the lapse of time until finally the decay curve tends to become flat. With an increase in the number of the paper layers, the interface charge density decreases. So in real life multilayer paper is used to avoid failures owing to its structural weakness. Regarding the DC polarity reversal effect, increasing the thickness of the paper is equivalent to adding paper layers. The dissipation rate of the positive interface charge is quicker than that of the negative one. In the polarity reversal test, the dissipation rate becomes smaller as the reversal time gets longer. [ABSTRACT FROM AUTHOR]

To investigate the characteristics of micro bridges and their interactions with partial discharge (PD) in oil-paper insulation under DC voltage, an experimental platform with two-copper-electrode models is established. Generation and growth of micro bridge impurities are observed. PDs in experimental process are detected and analyzed. The result shows that the generation and growth of micro bridges have three stages based on their quantity and shape. At first stage PD accelerates the generation of micro bridges. At second stage the grown bridges trigger stronger discharges. At the last stage a so-called "hazardous bridge" that triggers highly intensive PDs emerges, through which breakdown happens. Therefore, bridges and PDs promote each other to cause insulation failure. In addition, impurities at the second stage are observed to transform into pile-like, bridge-like or particle-like shapes. The transformation process is considered to relate with the change of composition force on fiber bundles. Besides, a "cluster discharging" phenomenon is observed at the second stage, which is associated with the generation and disappearance of micro bridge impurities. [ABSTRACT FROM AUTHOR]

This paper presents an experimental work investigating the failure data of oil-impregnated paper under pulsating DC voltage. The failure data of the oil-impregnated paper specimens were obtained through constant voltage stress tests; the Weibull distribution was used to estimate the statistical distribution of failure data. The exponential function (EF) and the inverse power function (IPF) were used to modify the Weibull distribution of failure data, so as to obtain two dual-variable Weibull failure distributions (WFDs), which were used to analyze failure data of oil-paper specimens obtained under pulsating DC and individual DC and AC voltages. Their adequacies were evaluated by using failure data obtained through the constant stress tests under various voltages. Both EF-modified and IPF-modified WFDs show more adequacy for failure data of oil-paper insulation under DC and pulsating DC voltages than AC voltages. The EF-modified WFD was more adequate than IPF-modified WFD in estimating the statistical distribution of failure data. [ABSTRACT FROM PUBLISHER]

The oil-paper insulation of valve-side windings in a high voltage direct current (HVDC) converter transformer is subjected to both complicated voltage and severe thermal stresses. Partial discharge (PD) occurring in oil-paper bounded cavities is influenced by voltage stress type as well as temperature. This paper presents PD behaviors in an oil-paper bounded gas cavity under pulsating DC voltages. The voltage across the gas cavity and PD inception voltages at different test conditions are analyzed. Influences of temperature on statistical PD distributions and parameters are also presented. A numerical model is used to interpret PD behaviors under pulsating DC voltages and various temperatures. Experimental results and theoretical statements show that the temperature exhibits a great influence on the behaviors of cavity discharge under pulsating DC voltages. Volume resistivity, gas pressure, charge decay time constant, and electron generation rate are the primary parameters influencing PD behaviors at different temperatures. [ABSTRACT FROM PUBLISHER]

The oil-impregnated paper, as a vital part in the oil-paper insulation system, serves as the main insulation medium in converter transformer suffering various electric fields. However, the accumulated surface charge on the paper would accelerate the degradation of insulation system and may lead to surface flashover. Direct-fluorination is a method to change the chemical components of polymer matrix thus could affect the surface property of the dielectric material without the alternation of bulk property. This paper presents a method to modify the surface structure of the paper applied in transformers. The paper used in the experiment was treated using the F2/N2 mixture with a volume fraction of 10% for the F2 gas at a pressure of 0.05 MPa in a reaction vessel for 2, 5, 10 and 15 min, respectively. The chemical elements, functional group and physical morphology of the paper before and after modification were measured with energy dispersive X-ray spectroscopy (EDAX), attenuated total reflection infrared (ATR-IR) and scanning electron micrographs (SEM), respectively. Surface and volume resistivity of the fluorinated paper were measured. Furthermore, the surface charge property of the oil-impregnated paper was measured under various positive and negative voltages. Obtained results showed that the fluorination had an obvious influence on the chemical property and surface structure of the paper leading to the reduction of surface and volume resistivity. The treatment was shown to reduce the initial potential and cause acceleration in charge decay process. The trap distribution of the paper surface presented alternation as well. [ABSTRACT FROM PUBLISHER]

Heretofore, unlike HVAC transformers, there is not much experience in both insulation design guides and test methods for ultra HV converter transformers. This special insulation phenomenon is very prominent due to the complication of voltage applied on valve-side windings of converter transformers. There is a severe lack of empirical research on partial discharge in oil-paper insulation under the combined ACDC voltage. The study in this paper provides a timely research into the issues. Nine possible configurations, which intent to simulate different defects in the transformer, have been investigated. The PD inception voltages varied ratios of combined AC-DC voltages were conducted. The discharge magnitude and its relation with the applied voltage for selected four common configurations were obtained during voltage increasing and decreasing respectively, which presented the PD initiating process and also reflected the insulation behavior of dielectrics. Besides, the Finite Element Analysis Soft was used to propose the effect of morphology of electrode surface (3 dimensional roughness is approximately 0.03 mm) on PD characteristics, which is very lacking in the previous references. The roles of DC and AC component in PD characteristics were discussed in the context of the relevant work in literatures. [ABSTRACT FROM AUTHOR]

In this paper, the rapid aging due to Partial Discharge (PD) activity was investigated in unaged and thermally aged oil-impregnated paper with a disk-shaped cavity between the sheets of paper. The PD inception voltage and the voltage for instantaneous breakdown were measured, and the time to breakdown was measured by applying voltages less than the instantaneous breakdown voltage. A comparison between time to breakdown of unaged and thermally aged paper shows no significant difference between thermally aged and unaged paper at sustaining PD activity. The time to breakdown as a function of applied electric field was plotted and compared for both cases showing points scattered around a line in log-log scale. Changes of the PD parameters, such as PD magnitude and PD repetition rate were analyzed from the beginning of PD activity up to the moment of breakdown. The results show that the number and magnitude of PD increase at the beginning of aging until they reach to a maximum value, then both quantities decrease slowly over time until the final puncture breakdown occurs. The results emphasize the importance of PD monitoring on real equipment with oil-impregnated paper as insulation system, such as power transformers, since a focus on the number and magnitude of PD at just the present time may mislead the interpretation. Dielectric spectroscopy measurements performed on unaged and thermally aged paper showed an increasing trend of ε" after the sheets of paper were exposed to thermal aging for longer time. Dielectric spectroscopy measurements performed on samples before and after exposure to PD activity showed a big change of ε", This change can be attributed to byproducts and ions produced by PD activity. [ABSTRACT FROM AUTHOR]

The effect of HV impulses on surface and cavity partial discharges (PD) of oil-impregnated paper (OIP) is investigated in this work, by subjecting specimens to impulse voltages superimposed on a continuous AC voltage. The superposition of transient and AC voltage is relevant to insulation systems in power-system equipment, which is exposed to transients such as lightning and switching impulses during its operation. For several different PD-generating defects in oil-impregnated paper, the PD behaviors before and after the impulse are compared. The influence of moisture content is studied by using OIP with moisture content <0.5%, 3.0% and 5.5%. The results show a distinctive behavior of PD due to the impulse for each defect and insulation condition, either by change in the PD rate and magnitude or by causing PD inception or extinction. Recordings of the voltage signals and associated PD measurements during and after the incidence of a high voltage transient are of potential use for condition assessment of the insulation of power transformers and their bushings, as a form of online diagnostics. [ABSTRACT FROM AUTHOR]

In comparison with the AC and DC working voltages, the effect of switching impulse voltage on insulation is very different because of its fast-rising rate and large amplitude. This paper mainly focuses on the characteristics of PD in oil-impregnated paper insulation under switching impulse voltage. First, a robust experimental platform was set up including the impulse power source, test samples with uniform gas and oil gap, and the signal acquisition and processing system. PD characteristics in the air and oil gap are analyzed and compared involving the time-domain waveforms, the variation tendency of the average amplitude and numbers of PD pulses, the occurrence time and the instantaneous value of impulse corresponding to the first PD. Based on the dielectric barrier discharge (filament) theory, a parallel microcircuit model was established to explain the similarities and dissimilarities, and to evaluate the gap discharge intensity. The occurrence and development of PD under switching impulse voltage of typical oil-impregnated paper defect were studied systematically with simulation, experiments, and modeling. [ABSTRACT FROM AUTHOR]

The oil-impregnated paper, which is the major section in converter transformer, plays a considerable role in the reliability and safety of power grid. However, the insulation degradation will be accelerated by the accumulation of charges that are on the surface of oil-impregnated paper. Therefore, the operating overvoltage occurs and irremediable damage will appear. Direct fluorination is an effective method of modifying the chemical components of polymer matrix so as to have effects on the surface characteristic of the insulating material without reforming the bulk properties. In this research, for studying effects of fluorination on charge behavior on the surface of oil-impregnated paper under the application of DC and impulse voltage, the F2/N2 compound, which the volume fraction for the F2 gas occupied 10 % and the pressure was 0.05 MPa in a reaction kettle for 5, 30 and 60 min respectively, was applied. Meanwhile, the chemical bond groups and the surface morphology of the fluorinated specimen were tested. Besides, the DC voltage amplitude was 4 kV and the applied time was 4 min. The impulse frequency was 500 Hz and the impulse voltage amplitude was 1, 2, 3 and 4 kV, respectively. The charge properties under various situations were investigated. From the research under the application of different fluorination time, impulse voltage amplitudes and polarities, conclusions can be drawn that, fluorination has significant effects on the chemical structure properties and surface characteristic of oil-impregnated paper. Furthermore, the initial potential can be reduced and the decay process of surface charge can be accelerated with different fluorination time increasing from 0 to 30 min. Nevertheless, the tendency is the opposite when the fluorination time continuously extends from 30 to 60 min. The trap distribution also exhibits alternation through the fluorination. [ABSTRACT FROM PUBLISHER]

Due to its excellent performance, oil-paper insulation has been widely used in many power apparatuses including converter transformer of high voltage direct current (HVDC) system. Space charge accumulation phenomena may significantly distort local electric field inside transformer and cause oil-paper insulation overstressing. As a result of long term operation, oil-paper gradually degrades. In most severe cases, the breakdown of insulation system may occur. In this work, the effect of space charge on breakdown characteristics of aged oil-paper insulation is investigated. Oil-paper samples with different aging states are obtained by thermally accelerated aging for various periods of time, categorized by the degree of polymerization (DP) of 1107 (new), 725, 504, 376 and 241, respectively. Experimental results show that the breakdown voltage of oil-paper samples without pre-stressing remains almost constant with thermal degradation. After the homo-polarity pre-stress, when the DP value is higher than ∼300 (from 1107 to 376), the breakdown voltage has an increasing tendency with an increase in thermal degradation. On the contrary, the breakdown voltage presents a decreasing tendency after the hetero-polarity pre-stress. When the DP is lower than ∼300 (DP241), the changes of breakdown voltage does not remain the same trend as previous samples after pre-stressing. Meanwhile, space charge distributions in different aged samples are measured by the pulsed electro-acoustic (PEA) method, and the trap parameters are correspondingly evaluated. It has been experimentally demonstrated that special attention should be paid to space charge accumulation and aging state of oil-paper insulation, which may lead to severe insulation accidents. [ABSTRACT FROM AUTHOR]

Oil-paper insulation system is an extraordinarily essential system of converter transformers as well as HVDC bushings. When the system changes its state, such as switching the thyristors, operating over-voltage appears, and the charge will deform the dielectric internal electric field, thus easily leading to the occurrence of discharge or insulation failure, so charge accumulation and dissipation on oil-paper insulation under pulse voltage need more investigation. This paper studies the surface charge behavior on double-layer oil-paper insulation under pulse voltage and inducing electrification was used to charge the oil-paper composite. Studies of various voltage amplitudes, pulse frequencies, numbers and polarities showed that the decay is fast initially, and then becomes slower with the time. Eventually the dissipation of charge behaviors tends to be flat. With the increase of voltage amplitudes, the surface potential rises, and less positive charges are accumulated on the surface than negative charges. The increase of the pulse frequency causes the initial values of surface potential a little smaller and the charge to dissipate more quickly. Also, with the increase of pulse numbers, the initial value gets bigger and the surface charge would be slowly dissipated. From the tdV/dt and decay time curves, the figures of positive voltage usually have two peaks, while there is only one peak in most of the curves under the negative one. With the increase of voltage amplitudes, the charge will dissipate more quickly. Additionally, the peak value and the characteristic time increase with the reduction of pulse frequency and the addition of numbers. [ABSTRACT FROM PUBLISHER]

An oil-paper insulation system which will withstand DC voltage under normal conditions is a key component of converter transformers as well as high voltage direct current (HVDC) bushings. When the system changes its state, operating overvoltage appears. This kind of overvoltage will consequently affect the application of oilimmersed facilities and the safety of entire grid. Therefore, this paper studies the charge coupling behavior of double-layer oil-paper insulation under DC and pulse voltages. From the research of different pulse voltage amplitudes, pulse numbers and polarity, conclusions can be drawn that, with the increase of the pulse voltage amplitudes, DC and pulse voltages in the same polarity cause the absolute value of the initial surface potential to decrease and then rise; while in different polarities, the charge with the same polarity as the pulse voltage increases. Furthermore, for the same pulse voltage, the absolute initial value of the DC voltage applied in the same polarity is higher than that in different polarities. Considering the pulse number effect, it is obvious that the initial value increases with the increase in the pulse number, and then reaches saturation. Also, with the increase in pulse number, the decay rate decreases and thus the charge is slowly dissipated. From the tdV/dt and the decay time curves, the peak value increases with the increase in the pulse number, while the characteristic time varies by the polarity of the DC and pulse voltages. [ABSTRACT FROM AUTHOR]

Space charge behavior is important in the oil-immersed-paper insulation in converter transformers for HVDC transmission. This paper reports an investigation of the space charge property in samples with two layers of oil-immersed-paper and oil. Based on pulsed electroacoustic (PEA) technique, a waveform recovery method was proposed to get rid of the effects of interface and anisotropy on PEA result, and the space charge distributions in the two-layer samples under different voltage and oil thicknesses were measured. It?s found that the charges with the same polarity as oil side electrode were accumulated at the interface and gradually increased with the increase of applied voltage. However, the positive charge charges always appeared in the oil under positive and negative voltages. Moreover, the charges in samples increased with the increase of applied voltage, while the amount of interface charges decreased with the increase of oil thickness. Due to the existence of interfacial charges, the electrical field in oil-immersed-paper was distorted with its maximum close to the interface. It is indicated that due to the different mobility properties of charges in paper and oil and the interface trap state, the interface between paper and oil plays an important role in charge formation and decay. [ABSTRACT FROM PUBLISHER]

Oil-paper insulation system is an extraordinarily essential system of converter transformer as well as HVDC bushing. This paper studies the interface charge accumulation and dissipation characteristics of oil-paper insulation system under DC voltage. In this paper, an induced electrification was used to charge the oil-paper samples. The amplitudes of the DC voltage varied from 1 to 4 kV and the paper was 0.13 mm in thickness. From the research of different voltage amplitudes and charging times of the paper, conclusions can be drawn that the decay is fast initially, and then becomes slower with the lapse of time. At last the dissipation trend tends to be flat. With the increase of the voltage amplitudes, the surface potential rises more rapidly, and higher voltage would also cause the charge to dissipate more quickly. Longer charging times would cause the charge to dissipate a bit more slowly. The decay rate of the negative voltage is a little smaller than that of the positive charge. Moreover, when it comes to the effect on the interface charge of the paper layers, the surface potential is more proportional to the increase of paper layers. When the amplitude of the voltage applied in the test is small or the charging time is short enough, the interface charge can be hardly accumulated on the bottom layer. In addition, the tdV/dt and the decay time curves under the positive voltage usually have two peak values, while there is only one peak value in most of the curves under the negative condition. [ABSTRACT FROM PUBLISHER]

The paper presents new diagnostic method applied to assess aging degree for paper-oil insulation used in professional electrical power device, primarily including medium and high power transformers. The described method is based on modified diagnostics using the recovery voltage effect occurring in dielectrics (RVM ? Recovery Voltage Methods). Modification of the RVM method applied so far, which is now used only to assess moistening degree for paper-oil insulation in power transformers, consists in a new parametric analysis of recovery voltage time characteristics. Simulation and experimental tests carried out in laboratory conditions for adequately prepared insulation samples have proven that the time-constant of recovery voltage decay (?R_MIN) is the most susceptible parameter as regards quantitative change in the function of aging of the examined insulation. This conclusion is also confirmed by statistical studies, in which a multi-parameter variance analysis method has been applied. An original equivalent circuit diagram of the insulation has been used to simulate aging degree of paper-oil insulation samples in numerical tests. The diagram is based on the Cole-Cole type dielectric response model. [ABSTRACT FROM AUTHOR]

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

A method of predicting the residual breakdown electrical field strength of an epoxy-mica paper insulation system is described. This method was developed by using data on service?aged stator bars from generators as well as accelerated aging model bars. Thermal aging, mechanical aging, and combined thermal and mechanical aging were done individually as accelerated aging. The partial discharge characteristics, dissipation factor, and breakdown voltage were measured on the model bars and service?aged bars from generators. From these results, the residual breakdown electrical field strength was predicted based on the partial discharge characteristics and dissipation factor. First, the dominant type of deterioration (thermal or mechanical aging) on a bar?s insulation was determined by the pattern of voltage?partial discharge magnitude characteristics. Then the residual breakdown electrical field strength was predicted by using a predicting equation for both thermal and mechanical aging. Each predicting equation uses dissipation factor tip-up (i.e. difference in dissipation factor values between 2 kV and rated voltage) and partial discharge inception electrical field strength. The accuracy of this method was confirmed using data measured on 112 service-aged stator bars from generators and 10 accelerated aged model bars. The 95% confidence interval level included 94% of the measured residual breakdown electrical field strength values. This result shows that the method enables precise predictions of the residual breakdown electrical field strength of an epoxy-mica paper insulation system. [ABSTRACT FROM AUTHOR]

Repeated impulses have long been considered to affect the insulation properties of electrical equipment. This interesting but rarely studied phenomenon may pose great risks to the reliable operation of power equipment. Therefore, in this work, we focus on the accumulative effect of repeated lightning impulses on the oil-impregnated paper (OIP) used in power transformers. Specifically, we study the effect of space charge on the accumulative characteristics of OIP. A repetitive impulse accumulating test platform was set up, and the tests were conducted to obtain the accumulative characteristics of OIP under repeated lightning impulses. The accumulative characteristics of OIP with various interval time were experimentally identified to study the influence of interval time on the accumulative effect. Then, space charge in OIP samples were investigated using the pulsed electro-acoustic technique. Charge behavior in OIP was analyzed under different conditions, i.e., changing the applied times, amplitude and interval time of the applied lightning impulses. Charge injection and transport occurred during lightning impulse accumulation. The increased application of lightning impulses, high applied voltage, and short interval time contributed to the accumulation and transport of space charges. At last, the possible mechanisms of the accumulative effect are discussed in this article based on the experimental results. [ABSTRACT FROM AUTHOR]

Compared to conventional ac cables, the current rating of HVDC cable circuits is more complicated because the permissible current is not only limited by the operating temperature, but also by the electrical stress within the insulation. Therefore the IEC60287 current rating standard is considered insufficient for some HVDC applications because it fails to include the stress limitation. This paper presents an analytical methodology to calculate an electrical stress-limited rating for HVDC cables, which considers the maximum dielectric stress as the current limiting factor. This paper represents the first part of a project which has comprehensively reviewed cable rating calculations for mass impregnated HVDC cable systems. [ABSTRACT FROM PUBLISHER]

The nonlinear ac–dc composite electric field in the winding area of the converter transformer was studied by considering the frequency and temperature dependence of the insulation materials in this paper. First, the relative permittivity and conductivity of vegetable oils, mineral oils, and insulation papers were measured at different frequencies and temperatures. Then, the oil-paper insulation structure model of one 500 kV converter transformer valve-side winding was established. The nonlinear composite electric field of the converter transformer insulation with vegetable oils and mineral oils was analyzed. The maximum voltage of the converter transformer with mineral oils is 524.9 kV, at −20 °C and that with vegetable oils is 497.1 kV. The results show that the calculation method proposed in this paper is more accurate than the traditional superposition method. [ABSTRACT FROM AUTHOR]

This paper presents an online method to monitor the conditions of the substation grounding grid. The proposed method utilizes phase-to-ground faults occurring in downstream feeders as test current sources and the neutral of a specially selected feeder as the electrode for GPR (ground potential rise) measurement. The measured fault currents and GPRs are then used to estimate substation grounding grid impedance. The method, once established, can monitor the grounding grid impedance continuously and automatically, and the trend of the impedance change can be observed. As a result, the proposed method can yield much more reliable information on the substation grounding conditions. The method also overcomes many disadvantages of the offline methods. The proposed idea, algorithm, and hardware setup are described in the paper. Factors contributing to measurement errors are investigated in detail. [ABSTRACT FROM AUTHOR]

The purpose of dissolved gas analysis (DGA) in utilities is to help detect the presence of abnormality within transformer. When faults occur in transformers, transformer engineers need to determine the location and risk of the faults. Ultimately, they have to decide, based on DGA, whether to continue operating or not, perform internal inspection, or dispose the transformer. In this study, the fault and failure types in the transformer are suggested to determine the location and risk of the faults. In particular, turn-to-turn insulation faults are classified as degradation and breakdown. These faults are difficult to identify during internal inspection, and have a high possibility of failure. Urgent decision and action are thus required to avoid failure. In degradation of turn-to-turn insulation faults, failures may occur by generating thermal gases in paper during a long period of time. In breakdown of turn-to-turn insulation faults, thermal gases are not generated in paper, and failures are rather due to sudden breakdown of insulation. This study also presents a typical example of a turn-to-turn insulation fault. This example shows the progress of the fault from thermal to discharge, which is common phenomena in winding fault. Based on the findings of this work, transformer engineers can determine by DGA if transformers can be operated with or without internal inspection, or disposed when the fault has not been identified during internal inspection. [ABSTRACT FROM AUTHOR]

An closed oil circulating system with plane electrode was built to study the effect of space charge on oil flow electrification under DC voltage. The results reveal that with the increase of applied voltage, the streaming current was always enhanced. However, the polarity of streaming current depends on the sample configuration. If the negative high voltage electrode was exposed to oil layer, streaming current was negative. Otherwise streaming current had a tendency to be positive as applied voltage increased. In experimental model without exposed electrode, the polarity of streaming current was always positive. And the amplitude of streaming current was related to the number of insulating papers placed under electrode. More craft papers placed under negative high voltage electrode led to the increase of streaming current. Based on the bipolar transport model, a new simulation method is proposed to study the effect of charge injection and transportation on flow electrification under DC voltage. The simulation results agree well with the experimental result. [ABSTRACT FROM AUTHOR]

An increasing need for fast and reliable models has led to a continuous development of Fourier-based (FB) analytical modeling. This paper presents an overview of the techniques that are currently available in FB modeling for electric machines. By coupling that overview to the most relevant literature related to the subject, an interesting starting point is provided for anyone who wants to use or improve FB models. The following seven aspects of FB models are discussed in detail: 1) the magnetic potential (scalar or vector potential); 2) the coordinate system and the solution of the partial-differential equations for each magnetic potential and for each coordinate system; 3) the way in which time dependence is accounted for; 4) the implementation of the source terms; 5) the possibilities to account for slotted structures; 6) the modeling of eccentricity; and 7) the post-processing computation of physical quantities, such as flux density, electromotive force, torque, losses, and eddy currents in conductive objects. Furthermore, this paper gives the closed form solution of the Laplace, Poisson, and Helmholtz equations in each coordinate system. In addition, this paper tackles other important features of FB models such as computational time reduction and coupling the machine model to an electric circuit. [ABSTRACT FROM AUTHOR]

This paper discusses a recent event in the western American power system when a forced oscillation was observed at a frequency that was close to a well-known 0.38-Hz inter-area electromechanical mode frequency of the western system. The event motivates a systematic investigation in this paper on the possibility of resonant interactions between forced oscillations and electromechanical inter-area oscillatory modes in power systems. When the natural oscillatory mode of a power system is poorly damped, and the forced oscillation occurs at a frequency close to system mode frequency at critical locations for the mode, resonance is observed in simulation test cases of the paper. It is shown that the MW oscillations on tie-lines can be as high as 477 MW from a 10-MW forced oscillation in Kundur test system because of resonance. This paper discusses the underlying system conditions and effects as related to resonance in power systems caused by forced oscillations and discusses ways to detect such scenarios using synchrophasors. Simulated data from Kundur two-area test power system as well as measurement data from western American power system are used to study the effect of forced oscillations in power systems. [ABSTRACT FROM AUTHOR]

We are pleased to announce that the February 2018 issue of the IEEE Transactions on Dielectrics and Electrical Insulation (TDEI) will be a special issue on High Voltage Direct Current (HVDC) Transmission System Insulation topics. [ABSTRACT FROM PUBLISHER]

Phase angle measurements from synchrophasors show discontinuities when they roll over from +180 to -180 degrees or vice versa. This paper proposes efficient strategies for unwrapping of the angles in real-time data streams. Examples presented in this paper first show that the phase angle differences across bus voltage phasors can go over 360 degrees in a synchronized power system under stressed conditions. Unwrapped phase angles are shown to be useful in fast reliable islanding detection methodology, and for phase angle arithmetic such as for averaging of phase angles and for phase angle difference calculations. Strategies for handling missing phase angle data in real-time data streams are also discussed. [ABSTRACT FROM PUBLISHER]

When an alternating voltage is applied to a dielectric material, dipoles in the material try to align in the direction of the applied voltages and polarization process starts. For multi-dielectric media especially in which a liquid interface is involved, such as oilpaper insulation, interfacial polarization is predominantly active among all polarization processes. This interfacial polarization is a very slow process and is effective in lower frequency range. This interfacial polarization reflects the inherent condition of the oilpaper insulation. Due to this reason, frequency domain spectroscopy is performed in lower frequency range to assess the condition of oil-paper insulation. So, the time required for frequency response measurement using conventional frequency domain spectroscopy is quite long. Considering the aforesaid facts, a different procedure has been taken here to measure the dielectric response in a significantly lesser time keeping the entire frequency range of conventional frequency domain spectroscopy. Instead of using pure sinusoidal excitation voltages over wide frequency range, dielectric response current has been measured using excitation having time growing frequency sweep (TGFS) signal. For this purpose, test samples that emulate the oil-paper insulation of real-life transformer have been prepared in the laboratory. The moisture contents of the test samples have been kept different to investigate the reliability of the proposed method. A setup has been made in the laboratory to measure dielectric response currents using the both excitations. In order to investigate the applicability of the proposed method, experiment has also been performed on actual transformers. It has been observed that the use of excitation signal having time growing frequency sweep provides almost similar information regarding insulation condition as obtained by the use of conventional sinusoidal excitation voltages. Hence, the proposed method is capable of reduction in time in FDS nearly by an amount of 85%. [ABSTRACT FROM PUBLISHER]

In this paper, a new hybrid stator fabrication with 2-D steel sheets lamination and 3-D end cap structure for high-speed motor application is provided. With the additional overhead end cap design, the new motor not only features lower iron losses in high frequency and reduces copper losses like traditional soft magnetic composite (SMC) motor but also achieves higher permeability and lower production cost at the same time. In this paper, the motor characteristics, i.e., back electromotive force and efficiency between the traditional lamination, SMC, and the new hybrid design are investigated by 3-D FEA simulation. Moreover, a prototype is fabricated by 3-D printing for the verification of the analytical and simulation results. [ABSTRACT FROM AUTHOR]

The introduction of an equivalent model for a regional power area in a large-scale power system with complex loads is essential for reducing the computation burden in real-time dynamic analyses. In this paper, we propose a generalized discrete-time equivalent model (GDEM) with specific relations among model parameters for simulating the physical characteristics of a regional power area. The GDEM facilitates the interconnection of equivalent models representing regional power areas and improving the simulation accuracy and speed in large-scale dynamic power systems. This paper first investigates the inherent relations among GDEM parameters in the discrete-time models of synchronous generators and composite loads so as to guide the GDEM parameter estimation in regional power areas. This paper then develops relations among GDEM parameters for a regional power area. Numerical experiments are conducted by simulating ground faults in the China Electric Power Research Institute system and the accuracy of the proposed GDEM is verified by analyzing the dynamic simulation results. In addition, this paper has applied the GDEM to study the regional power area of Central China, which validates the use of GDEM in practical power system analyses. [ABSTRACT FROM AUTHOR]

A new modular pulsed-power source with fast rise time and step-wise arbitrary output waveform generation is currently under development to drive the Gepulste Elektronenstrahlanlage device investigated at the Institute for Pulsed Power and Microwave Technology (IHM). Acknowledging the complex design procedures necessary to set up a modular pulsed-power source for voltages of up to 120 kV, this paper focuses on the circuit design for a single stage and its validation prior to the generator assembly. Using a semiconductor-based Marx generator topology, the stages are designed to have an output voltage of 1 kV with a pulse current of up to 600 A. When connected to an ohmic load, the measured current rise times are in the order of 46 ns resulting in the current rise rates of up to 10 kA/ $\mu \text{s}$ using the commercial devices. The step-wise arbitrary output waveform is created by generating the switching commands on the stage using a microprocessor and a fast optical synchronization unit. Effective stage shielding is verified by operating the stage in a 100-kV, 2.5-kA electromagnetic interference test bed. This paper presents the design considerations and the corresponding measurements. [ABSTRACT FROM AUTHOR]

This paper presents a scheme for rotor position estimation from standstill to nominal speed. The proposed scheme is particularly suited for surface mounted permanent magnet synchronous motors and for slotless permanent magnet synchronous motors with completely smooth cylindrical rotor, which cannot be operated with state-of-the-art sensorless methods seamlessly from standstill. At standstill and very low speed, the position is estimated by using signal injection. A systematic distortion in the position estimation that is due to asymmetries in the motor parameters is identified and compensated. The rotor polarity is identified by a special process based on the estimation of the back electromotive force (back EMF) induced by a minimal rotor motion. At high speed, the position is estimated by using a linear back EMF observer. Different observer gains are used at different speed ranges, so that the position estimate is reliable even at low speed. The combination of these two approaches enables sensorless motor control in the full speed range including standstill. Experiments demonstrate the accuracy of the proposed estimation scheme and its robustness under different thermal conditions. This paper is accompanied by two videos demonstrating sensorless operation. [ABSTRACT FROM AUTHOR]

In a common dc-link dual-fed open-end winding permanent magnet synchronous motor (OEW-PMSM) topology, it is well known how the additional flow of a zero-sequence current (ZSC) is permitted. The low zero-sequence impedance characteristic of high-speed machines leads to high-intensity and high-frequency ripple of the ZSC. Therefore, there is a necessity to eliminate the zero-sequence-voltage (ZSV) produced by the two voltage source converters that feed the machine. Furthermore, the non-sinusoidal back electromagnetic force (back EMF) causes the circulation of a third harmonic ZSC. An OEW-PMSM high-speed starter-generator fed by a dual-inverter with a single dc-link is considered. Part I of this paper proposes a modulation for the considered topology able to eliminate instantaneously the ZSV produced. In this paper, a detailed analysis of the deadtime (DT) effect on the ZSV has been carried out and a novel hysteresis control for the ZSC using the DT as a control action is presented. The DT produces a ZSV distortion on the zero-axis that can be used to control the third harmonic ZSC flowing due to the non-sinusoidal machine back EMF. [ABSTRACT FROM AUTHOR]

Conventionally, for a tubular permanent magnet synchronous linear motor (TPMSLM), adopting a modular structure can effectively reduce the detent force; however, the thrust density is sacrificed via the large proportion of the flux barrier to the total primary component volume. To overcome this disadvantage, this paper proposes a novel modular TPMSLM, in which the unit primary component adopts the large slot structure containing several coils. Focusing on this motor, research on the flux linkage characteristic is performed to obtain the design principle, and then the detent force is analyzed and suppressed by reasonable design of end teeth. First, the flux linkage characteristics of the unit motor and the whole motor are investigated. Variation rule of the coil flux linkage affected by the end tooth is discussed, and the principle of realizing three-phase balance for the whole motor flux linkage is elaborated. Moreover, the principle of the detent force suppression is verified and the detent force is further suppressed through the end tooth design. Finally, a prototype is developed. The back electromotive force and the detent force were tested, which verified the effectiveness of the novel modular TPMSLM proposed. [ABSTRACT FROM AUTHOR]

In this response, we show that the paper by Kim et al. by our group has a different research purpose and uses different modeling processes, which was not described in the previous work by Ortiz-Conde et al. The comments issued by Ortiz-Conde et al., who claim that our paper corresponds to a particular case of their previous work, are in our opinion overgeneralized. Differences compared to Ortiz-Conde’s previous work are discussed in detail. We also explain how the problem on threshold voltage pointed out by Ortiz-Conde et al. can be solved through a semiempirical method from measured data. [ABSTRACT FROM AUTHOR]

A modular multilevel converter control system, based on converter energy storage, is proposed in this paper for two different control modes: active power and dc voltage. The proposed control system decouples the submodule (SM) capacitor voltages from the dc bus voltage. One of the practical applications is the management of active redundant SMs. A practical HVDC system with 401-level MMCs, including 10% redundancy in MMC SMs, is used for validating and demonstrating the advantages of the proposed control system. This paper also presents a novel capacitor voltage balancing control based on \max–\min functions. It is used to drastically reduce the number of switchings for each SM and enhances computational efficiency. [ABSTRACT FROM AUTHOR]

Conventionally, integrated drain-extended MOS (DeMOS) like high-voltage devices are designed while keeping only performance targets for a given application in mind. In this paper, for the first time, performance and reliability codesign approach using 3-D TCAD has been presented for various superjunction (SJ) type DeMOS devices. In this context, how to effectively utilize the SJ concept in a DeMOS device for System on Chip applications, which often has stringent switching and RF performance targets, is explored in detail in this paper. Moreover, design and reliability tradeoffs for switching and RF applications are discussed, while considering two unique sets, one with fixed breakdown voltage and other with fixed ON-resistance. Finally, hot carrier generation, safe operating area concerns, and electrostatic discharge physics are explored and compared using 3-D TCAD simulations. [ABSTRACT FROM PUBLISHER]

The surface voltage of an insulator assumes importance for understanding tracking and flashover characteristics. Until now, determination of surface voltage of insulating surfaces is left to simulation software and such simulations are left unverified experimentally, leading to uncertainty of the results, which may sometimes be erratic with improper choice of boundary or initial conditions or inaccurate material properties, nonlinearities etc. The paper presents a novel method, using which the surface voltage of any insulating surface such as insulator strings or transformer bushings can be measured. Unlike a conducting surface, the measurement of insulating surface voltage using voltage dividers would be erratic as the measuring arrangement itself will vary the voltage division due to the local unknown impedance between the insulated surface and hv conductor. Recently a method for measurement of surface voltage of an insulated conductor using cylindrical strips was reported. In this paper, based on analytical derivations, a more generalized method of measurement, applicable to any point on an insulating surface of arbitrary geometry is proposed using circular-disc strips. The proposed experimental method is applied to insulator strings and transformer bushings and validated by simulation of the entire systems. The simulation and experimental results are in excellent agreement. [ABSTRACT FROM AUTHOR]

A comprehensive study of dielectric modulated (DM) drift regions for power devices is presented in this paper. The performance of this structure is theoretically analyzed and compared with both conventional and superjunction (SJ) structures. In this paper, an analytical model for DM drift regions with cylindrical cells is proposed and compared with linear cells. An optimal tradeoff between breakdown voltage (BV) and specific ON-resistance ( R\scriptscriptstyle ON,sp) is obtained by a methodology developed in this paper. 3-D simulations of DM structures with hexagonal cells approximated by cylindrical cells are conducted to verify the analytical model. Optimal BV– R\scriptscriptstyle ON,sp tradeoffs for devices with conventional and SJ drift regions are also obtained through the same methodology and verified by 3-D simulations. Static characteristics of these three different drift region structures in both Si and SiC power devices are compared. [ABSTRACT FROM AUTHOR]

DC microgrid has attracted more and more attention due to its unique characteristics, but the development of a dc microgrid is also facing some challenges, such as interruption and isolation of short-circuit fault currents. Therefore, the dc circuit breaker plays an important role in ensuring the normal work of a dc microgrid. In this paper, a novel bidirectional dc solid-state circuit breaker is proposed to realize the bidirectional flow of energy, which ensures the higher operating efficiency of the dc microgrid. Compared with other solid-state circuit breakers, the proposed novel topology has simpler structure, common ground, and fewer components. First, this paper makes a detailed analysis of the different working stages of the circuit when the fault occurs in combination with simulation results of the circuit topology. Then, the standard of selecting the components through the calculation and analysis of the circuit is given in this paper. Finally, the performance of the novel bidirectional solid-state circuit breaker is verified by experiments. [ABSTRACT FROM AUTHOR]

The dielectric screening property of a semiconductor is very crucial for the electrical characteristics of a MOSFET, and which can be described mathematically by Poisson equation via the permittivity. While the theory and experiments have corroborated the permittivity reduction of nanoscale Si, this paper studies the electrical characteristics of MOSFETs considering the reduced channel permittivity by quantum transport simulations. It is found that the channel permittivity reduction may mitigate the short-channel effects, showing subthreshold swing improvement and threshold voltage shift of MOSFETs in nanoscale. Compared to quantization effects, the positive and negative impacts of the channel permittivity reduction on the devices in particularly nanoscale have been investigated. This paper elucidates the necessity of considering semiconductor permittivity reduction for nanoscale device design and simulations. [ABSTRACT FROM AUTHOR]

Multichannel digital sinewave generators play a key role in digital automated impedance bridges. Along with the technological progress in the development of commercial data acquisition (DAQ) boards, which brings with it improvements in their metrological and functional properties, it is possible to realize the DAQ-based high-precision multichannel generators. This paper describes the evaluation of properties of three commercial DAQs, available in the form of PCI eXtensions for Instrumentation modules and working as two-channel generators supervised by software developed by the authors. Due to the fact that the main application area of these generators is digital impedance bridges, this paper presents research results the most relevant for the impedance bridges, i.e., the stability of amplitude ratio and phase difference as well as total harmonic distortion and spurious-free dynamic range. The results and conclusion presented in this paper may be useful when choosing DAQs intended to be used in the multichannel generators. [ABSTRACT FROM AUTHOR]

The instability of amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) under ultraviolet (UV) light was thoroughly investigated in this paper. Unlike in a darkened state, an off-state leakage current can be found in the dual-sweep I–V transfer curve of a-IGZO TFTs under UV light illumination. Furthermore, despite the same UV light condition, the forward sweep and reverse sweep show different I–V curves, representing two different physical mechanisms. First, the subthreshold swing degradation and threshold voltage shift to the negative direction in the forward sweep are due to the total channel barrier lowering and can be confirmed by changing the light exposure region. Second, in the reverse sweep, the suggested back-channel leakage current can be controlled by dual-gate TFTs. UV light exposure of the metal–insulator–semiconductor–metal structure verifies that the off-state leakage current passes through the back channel in a reverse sweep. Finally, the physical mechanism links between forward and reverse sweeps have comprehensive interpretation in this paper. [ABSTRACT FROM AUTHOR]

This paper is an extension of the procedure pointed out to evaluate the distortion of the exponential signal, modeled as multiexponential signal with different amplitudes and time constants. This procedure evaluates the distortion by applying the Prony-like method to the signal reconstructed by zero-crossing time evaluated on the difference between the exponential original signal and the reference sinusoidal one. The extension proposed in this paper concerns with the use of the low-chirp signal as reference instead of the sinusoidal signal. The low-chirp signal permits to increase the number of the zero-crossing time in the section of exponential signal with the higher slope and decreasing in the section with the lower slope. This setting permits to estimate the distortion of the exponential signal with higher accuracy and precision. The parameters’ amplitude, phase, and start frequency of the reference low-chirp signal are used to reconstruct the exponential signal in the zero-crossing time in order to overcome the problem of the high-resolution sampling. Their estimation is carried out by the time-varying sine-fitting algorithm that processes the resulting signal that is the difference between the exponential original signal and the low-chirp signal. Advantages of the proposed extended procedure regard the direct estimation of the reference low-chirp signal parameters from the resulting signal over-sampled at low resolution, and the use of only one input acquisition channel that permits to overcome the synchronization problem between the reference and the resulting signal. The numerical and experimental tests validate the extended procedure. [ABSTRACT FROM AUTHOR]