Search

The wide application of magnesium alloys as biodegradable implant materials is limited because of their fast degradation rate. Hydroxyapatite (HA) coating can reduce the degradation rate of Mg alloys and improve the biological activity of Mg alloys, and has the ability of bone induction and bone conduction. The preparation of HA coating on the surface of degradable Mg alloys can improve the existing problems, to a certain extent. This paper reviewed different preparation methods of HA coatings on biodegradable Mg alloys, and their effects on magnesium alloys' degradation, biocompatibility, and osteogenic properties. However, no coating prepared can meet the above requirements. There was a lack of systematic research on the degradation of coating samples in vivo, and the osteogenic performance. Therefore, future research can focus on combining existing coating preparation technology and complementary advantages to develop new coating preparation techniques, to obtain more balanced coatings. Second, further study on the metabolic mechanism of HA-coated Mg alloys in vivo can help to predict its degradation behavior, and finally achieve controllable degradation, and further promote the study of the osteogenic effect of HA-coated Mg alloys in vivo. [ABSTRACT FROM AUTHOR]

The δ-TRIP steel has attracted a lot of attention for its potential application in automotive components, owing to the low density, good combination of strength, and ductility. As the difficulty in yield strength further increasement is caused by large fraction ferrite, the work hardening ability was enhanced by optimizing the manganese (Mn)-content in this study. Three δ-TRIP steels with different manganese (Mn)-content were designed to explore the significant effect of Mn content on the work hardening behavior in order to develop high strength steel suitable for the industrial continuous annealing process. The detailed effect of Mn on microstructure evolution and deformation behavior was studied by scanning electron microscope (SEM), interrupted tensile tests, X-ray diffraction (XRD), and in-situ electron backscattered diffraction (EBSD). The study suggested that 2 Mn steel has the lowest degree of bainitic transformation, as a result of fine grain size of prior austenite. The large TRIP effect and dislocation strengthening improve the work hardening rate, resulting in 2 Mn steel exhibiting comparable mechanical properties with the QP980 steels. The retained austenite in 1.5 Mn steel progressively transformed into martensite and sustained the strain to a high strain value of 0.40, showing a good strength-ductility balance. [ABSTRACT FROM AUTHOR]

The present work introduces the role of heterogeneous microstructure in enhancing the nucleation density of reversed austenite. It was found that the novel pre-annealing produced a heterogeneous microstructure consisting of alloying elements-enriched martensite and alloying-depleted intercritical ferrite. The shape of the martensite at the prior austenite grain boundary was equiaxed and acicular at inter-laths. The equiaxed reversed austenite had a K-S orientation with adjacent prior austenite grain, and effectively refined the prior austenite grain that it grew into. The alloying elements-enriched martensite provided additional nucleation sites to form equiaxed reversed austenite at both prior austenite grain boundaries and intragranular inter-lath boundaries during re-austenitization. It was revealed that prior austenite grain size was refined to ~12 μm by pre-annealing and quenching, while it was ~30 μm by conventional quenching. This is a practical way of refining transformation products by refining prior austenite grain size to improve the strength, ductility and low temperature toughness of heavy-gage plate steel. [ABSTRACT FROM AUTHOR]

The solidification structure and segregation of continuously cast billets produced by different continuous casting processes are investigated to elucidate their effect on segregated bands in hot-rolled section steel. It suggested that segregated spots are mainly observed in the equiaxed crystal zone of a billet. The solidification structure is directly related to superheating and the intensities of secondary cooling. To a certain extent, the ratio of the columnar crystal increases with the increase of superheating and secondary cooling. Moreover, the number of spot segregations decreases with the decrease of the equiaxed crystal ratio. After hot rolling, the segregation spots are deformed to form segregated bands in steels. The severe segregation of Mn in segregated bands corresponds with that in the segregation spots. The elongation ratio and low temperature toughness deteriorate significantly by a high fraction of degenerate pearlite caused by central segregation. With a decrease of central segregation, the total elongation is increased by 10% and the ductile–brittle transition temperature (DBTT) is also reduced from −10 to −40 °C. According to the experimental results, columnar crystal in billets is preferred to effectively reduce the degree of central segregation and further improve low temperature toughness and the elongation ratio. [ABSTRACT FROM AUTHOR]

Here, we elucidate the significant impact of carbon nanotubes (CNTs) on the electrochemical behavior of Mg-based amorphous composite materials that were reinforced with CNTs while using pressure die casting. The addition of 3 vol % CNTs led to an increase in the compressive strength of Mg-based amorphous material from 812 MPa to 1007 MPa, and the fracture strain from 1.91% to 2.67% in the composite. Interestingly, the addition of CNTs significantly contributed to the enhancement of corrosion resistance of Mg-based glass by ~30%. The superior mechanical properties are primarily related to the fact that the addition of CNTs hindered the growth of shear bands (cracks), while the high corrosion resistance is related to inferior wettability and the bridging effect between adherent corrosive oxide film and the matrix that provided enhanced corrosion resistance. [ABSTRACT FROM AUTHOR]

Herein, the influence of inter-pass cooling (IC) and conventional two-stage rolling (CTR), on microstructural evolution and plastic deformation behavior of ultra-heavy EH47 plates, is demonstrated. It is reported that the deformation amount and deformation rate, in every deformation pass during rough rolling, at 1/4- and 1/2-thickness of IC steel were higher than the CTR steel. The volume fraction of ferrite and acicular ferrite was 45% and 18%, at 1/4-thickness, and 35% and 50% at 1/2-thickness of IC steel, respectively, whereas the sum of both ferrite phases was smaller than 25% in the CTR steel. The austenite grain boundary area and high-angle grain boundary fraction in the IC steel were higher than the CTR steel. The high density of fine and shapeless pearlite has been observed in IC steel, whereas large-size carbides, with hexagonal structure, have been observed in CTR steel. Compared to the CTR steel, the density of precipitates was apparently lower in IC steel. Two kinds of Nb containing precipitates, such as (Ti, Nb)(C, N) and (Nb, Ti)C, were observed in the tested steels. Total ductility and uniform elongation of the IC steel were higher than the CTR steel. During the tensile process, the crack initiation energy and crack propagation energy of the IC steel were higher than the CTR steel. Moreover, the volume fraction of retained austenite (FCC) was reduced from 7.71% to 0.42% near the tensile fracture in IC steel at 1/4-thickness. In additon, the strain of synergetic plastic deformation of the IC steel was higher than the CTR steel. Meanwhile, compared to the CTR steel, the synergetic plastic deformation of the IC steel occurred at low stress after the yield point, which can be ascribed to the presence of fewer microcracks in the IC steel. Hence, a delayed fracture has been observed in the IC steel plate. [ABSTRACT FROM AUTHOR]

We elucidate here the determining role of Nb interlayer on mechanical properties of Ti/steel clad plate fabricated by vacuum rolling cladding (VRC) as a function of different heating temperatures. A critical analysis on the clad interface via electron probe micro-analyzer, X-ray diffractometer and shear testing were conducted to investigate the influence of TiC, Fe-Nb and TiFe compounds and Nb-Ti solid solution on microstructural evolution and shear properties of Ti/steel clad plate. The inter-diffusion between Ti, C and Fe was effectively restrained by adding the Nb interlayer at heating temperature of 800 °C, and average shear strength of 279 MPa was achieved. With increase of heating temperature, Nb-Ti solid solution was formed at the Ti/Nb interface, which reduced mechanical properties of clad plate at 900 °C. At 1000 °C, TiC and Nb-Fe compounds and Nb-Ti solid solution were formed at the interface, and minimum average shear strength of 152 MPa was achieved. The detailed analysis on the clad interface suggested that ideal shear strength can be obtained through the addition of Nb interlayer and selecting appropriate heating temperature. [ABSTRACT FROM AUTHOR]

In this study, the impact of different surface treatment and degree of vacuum on the interface and mechanical properties of 304/Q345 stainless steel clad plate was investigated. The study indicated that more continuous or aggregated Al2O3 and Si-Mn composite oxides were formed at the interface after brush grinding. However, less inclusions such as Al2O3, MnS and Ca-Mg-Al-Si composite oxides were formed at the interface after pickling treatment. For the vacuum degrees of 10−2 Pa, 1 Pa and 105 Pa, the oxidation reaction became more intense with the decrease in vacuum degree. The interface inclusions were gradually changed from Al2O3 and Si-Mn complex oxides to oxide scale and MnCr2O4 spinel oxide. The interfacial bonding strength of stainless steel clad plate was improved with the increase in degree of vacuum. The bonding strength was 55 MPa at vacuum of 105 Pa, but it was 484 MPa at vacuum of 10−2 Pa, which is far greater than that of the national standard, and an excellent performance was obtained. [ABSTRACT FROM AUTHOR]

Isothermal treatment affects the microstructural evolution and the precipitation behavior of high-strength low alloy (HSLA) steels. In this regard, thermal simulation of different isothermal treatment temperatures was adopted by using a thermomechanical simulator. The results showed that hardness reached the maximum value at 600 °C holding temperature, which was related to a finer grain structure and granular bainite. The strengthening effect of precipitates was remarkable due to the combination of small particle size and small interparticle spacing. It is presumed that the precipitation started after 600 s at 600 °C. Precipitation strengthening continued to exist, even though coarsening of ferrite grains led to softening phenomena when the specimen was isothermally held at 750 °C, which led to relatively high hardness. The precipitates were fcc (Ti, Nb) (N, C) particles, and belonged to MX-type precipitates. Average size of precipitates increased from 3.14 to 4.83 nm when the specimens were isothermally held between 600 °C and 800 °C. Interparticle spacing of precipitates also increased with increasing isothermal treatment temperatures. These led to a reduction in precipitation strengthening. At the same time the polygonal ferrite content increased and ferrite grain size got larger, such that the hardness decreased continuously., Competing Interests: The authors declare no conflict of interest.

In this study, a 304/20MnSi stainless-steel clad rebar was prepared by single-pass compression process using the MMS-200 Thermal Mechanical Simulator. The impact of different degrees of deformation and deformation temperature on microstructure evolution and the mechanical properties of stainless steel clad rebars were investigated. The study indicated that with the increase of the degree of deformation, the content of pearlite in a carbon steel matrix was increased, and the grains refined. The metallurgical bonding of the bonded interface was formed under high temperature and high extrusion force. With the increase of the deformation temperature, more bainite was obtained on the side of carbon steel, and the grain size increased. The obvious diffusion of Fe, Cr and Ni elements near the bonding interface resulted in higher microhardness of the stainless steel side and smaller microhardness of the carbon steel side. Moreover, the engineering stress-strain curves obtained by the tensile test showed that the plastic deformation of stainless steel and carbon steel was more coordinated. With the increase of deformation temperature and the degree of deformation, the tensile strength of the stainless steel clad rebar was as high as 690 MPa and the elongation was 26%, which was superior to the properties of the clad rebar prepared by other process parameters.