Search

Summary: In order to achieve efficiency extremum of power conversion independent of parameter values and operational mode, an adaptive dual‐controller on‐line efficiency optimization method is presented in this paper. Firstly, based on tri‐modal analysis for four‐switch buck‐boost (FSBB) converter, efficiency extremum analysis is given and existed for such this converter. Then, adaptive dual controller on‐line efficiency seeking algorithm is shown to adaptive two variables for efficiency optimization and output voltage regulation. Furthermore, perturb and observe detector is described to realize control variables decoupling of dual‐controller and to prevent the instability of the whole system during the algorithm tuning process and to improve the algorithm speed of the dual controller. The proposed method is model independent and does not depend on the circuit parameter values. The detail implement of algorithm and performance analysis is given, and the experimental platform and experimental results are put forward to verify the effectiveness of the algorithm. [ABSTRACT FROM AUTHOR]

The multi-level inverter (MLI) is more efficient due to its ability to eliminate low-order harmonics. Thus, it is widely used in renewable energy generation, electric vehicles (EVs), etc. The choice of the neutral-point clamped (NPC) converter topology as a research object is of great significance in practical engineering. However, complex modulation algorithms and neutral-point voltage unbalance are two inherent problems for such NPC inverters. In this paper, an improved multi-voltage vector model predictive control (MVV-MPC) strategy based on neighboring four voltage vector synthesis is presented for three-phase NPC inverters. The duty cycle calculation and derivation methods for the proposed method are very simple, and they were obtained through the action time of each voltage vector being inversely proportional to the value of the corresponding cost function. Moreover, the fixed switching frequency of this strategy is maintained and the current peak ripple is reduced, guaranteeing the preferred total harmonic distortion of the output waveform. Furthermore, a voltage balancing method based on zero-sequence voltage injection is utilized to achieve dynamic balancing of the midpoint voltage difference and to limit the oscillation magnitude of the midpoint voltage difference to within ± 1 V. Finally, MATLAB simulations and an HIL experimental platform are built to demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In order to address the issue of keeping the converter operating at a high efficiency level under different conditions, this paper suggests an adaptive step frequency adjustment online optimization search algorithm, which achieves the goal of fast adjustment and real‐time response to parameter changes. The converter is quickly adjusted to operate at a high efficiency by sampling the input and output current values and modulating the switching frequency utilizing the algorithm. Additionally, the algorithm shifts between two working models to finish the search for the best switching frequency while the converter's characteristics do not change. Moreover, it accomplishes the objective of instantly resynchronizing the algorithm after a change in the converter's parameters and starting a search for the best switching frequency in the new converter state. For various input voltages and output loads, the operating principle, optimal frequency, and efficiency are given. In addition, the principle analysis when the converter parameters are changed is provided, and the choice of two algorithm models is compared. Finally, a prototype buck converter with adjustable input voltage and load is constructed to test the algorithm's efficiency. [ABSTRACT FROM AUTHOR]

In order to break limited step-down ratio range and poor regulation capacity in the conventional resonant switched-capacitor converters for rectifier application, a single-stage ac/dc rectifier based on the dual-resonance switched-capacitor converter is proposed in this article. Through utilizing a dual-resonant structure and nonoverlapping strategy to realize wide continuous voltage gain of the proposed converter, high power factor (PF) and low total harmonic distortion (THD) based on the narrow dead zone are guaranteed by operating at high step-down conversion ratio in this converter topology. Moreover, the voltage gain is concentrated between resonant frequency and double resonant frequency to achieve a narrow switching frequency range for rectifier application. Furthermore, operating at flat voltage stress curves to obtain low voltage stress character. Comprehensive mode analysis, input PF and THD, and stress analysis are given, and analysis results indicate that the proposed power factor correction converter can work with soft turn on and zero-current turn off; high efficiency is realized. Finally, an experimental prototype with 85–130 Vac input and 47 Vdc/44 W output is built and tested for verifying the operation modes and PFC performance, and the comparison between different rectifiers and the proposed one is provided. [ABSTRACT FROM AUTHOR]

Dual active converter (DAB) can achieve high efficiency when the voltage ratio (the ratio of the input voltage to the output voltage equivalent to the primary side) is one, but when the voltage ratio is not one, the light-load efficiency drops sharply. Based on the realization logic of DAB light-load, this article proposes a modulation method with asymmetric compression duty cycle, which only increases one degree of freedom and does not need additional components to significantly improve the light-load efficiency. First, this article introduces the existing problems and solutions of the traditional scheme and puts forward a new modulation strategy. Then, the operating modes and power characteristics are analyzed. Then, the influence of duty cycle compression on reflux power and current stress is analyzed. Finally, a prototype with an input voltage of 100–200V, an output voltage of 50 V, and a full load power of 300–600 W is built to verify the analysis. [ABSTRACT FROM AUTHOR]