Search

To investigate the effects of different organic acid additives and their concentrations on the fermentation quality and bacterial community of paper mulberry silage, paper mulberry was left untreated (control) or was treated with ethylenediaminetetraacetic acid (EDTA), propionic acid (PA) or citric acid (CA), the amount of each additive was 2 g.kg−1 FM, 5 g.kg−1 FM and g.kg−1 FM. All groups were ensiled for 3, 7, 15, 30 and 60 days. Compared to the control, adding EDTA reduced protein breakdown, preserved more water-soluble carbohydrates of the silages (WSCs, 24.74 g.kg−1 DM), and high concentrations of EDTA inhibited the activity of undesirable microorganisms. Adding PA increased the abundance of Lactiplantibacillus and decreased the abundance of Enterococcus, and it caused a rapid decrease in the pH of the silage at an early stage (from 6.50 to 5.31) while altering the microbiota, and low concentrations of PA resulted in high LA (66.22 g.kg−1 DM) concentration and low PA (9.92 g.kg−1 DM) concentration at 60 days of ensiling. Different concentrations of additives altered the microbial community of paper mulberry to different degrees. High concentrations of PA and CA can increase the abundance of Lactiplantibacillus. High concentrations of CA resulted in a rapid decrease in silage pH at an early stage and higher WSC concentration. These results suggest that EDTA, PA and CA can be used as additives to improve the quality of paper mulberry silage.

Paper mulberry (Broussonetia papyrifera L., PM) is being used as a new type of animal protein feed to address the feed crisis. To investigate the effect of additives on the chemical composition, fermentation quality, and bacterial community of PM silage (at room temperature, 25°), paper mulberry was fermented with formic acid (FA), Amomum villosum essential oil (AVEO) and lactic acid bacteria (LAB) inoculant treatments. The results showed that fresh PM had a low water-soluble carbohydrate (WSC) content and large amounts of unclassified bacteria. Compared with the CK and LAB treatments, the FA and AVEO treatments significantly (P < 0.05) decreased the pH and increased the lactic acid content of PM silage after 60 days of ensiling. In the AVEO-treated silages the abundance of Lactococcus in the early stage of ensiling increased by 14.09%, the abundances of Levilactobacillus and Lentilactobacillus in the late stage of ensiling increased by 58.34 and 91.12%, respectively, and the abundance of Stenotrophomonas decreased by 94.71%, resulting in improved PM silage quality. These results confirmed that AVEO could potentially be developed as a new additive for improving the fermentation quality of silage.

The demand for eco-friendly packaging materials has urged researchers to look for alternatives to petroleum-based polymers. In this regard, paper-based products have turned out to be a promising choice; however, their weak resistance to water has limited their application. The use of various additives to enhance paper's moisture resistance is a common practice. However, considering the growing global agenda for sustainable development, the search for new bio-based paper additives has become increasingly important. This study investigated the potential synergistic impact of the addition of nanofibrillated cellulose (NFC) and chitosan additives (CHIT) to different fiber combinations to improve paper's properties, in particular, their wet strength. The efficacy of the additive application order was examined and was found to be crucial in achieving the desired outcomes. The results showed that incorporating CHIT after NFC enhanced the paper's tensile and burst indicators, as well as the paper stretch in the dry state, by 35–70%, 35–55%, and 20–35%, respectively. In addition, the tensile index and stretch in the wet state improved 9–13 times and 2.5–5.5 times over, respectively. The air permeability decreased 2.5–12 times over. These findings demonstrate that the sequential addition of the NFC and CHIT additives yield a greater enhancement of paper's properties than using each additive separately. [ABSTRACT FROM AUTHOR]

Microbial-induced calcite precipitation (MICP) is an innovative technology in civil engineering. However, the high cost of components and the fragility of the treated soil limit its wide use. One of the possible solutions is organic waste incorporation at different stages of the technology. In the present study, we consider the use of spent brewer's yeast (BSY) to produce bacterial inoculates and wastepaper, flax shives and sawdust as reinforcing additives into the soil. We showed that the replacement of expensive components of LB medium by BSY extract increased biomass growth characteristics of Bacillus subtilis K51, B. cereus 4b and Micrococcus luteus 6 strains by 1.4, 1.5 and 1.8 times, respectively, while for B. subtilis 168, they were comparable to LB medium. The urease activities of all strains were not reduced compared to the control. Among the three kinds of cellulose-containing waste, wastepaper incorporation into MICP-treated soil samples led to an increase in compressive strength by 2.1 times and precipitated calcite percentage by almost 1.5 times compared to a sample without additives. Thus, we showed the potential for soil stabilization through MICP using organic waste. [ABSTRACT FROM AUTHOR]

Tissue paper production frequently combines two main types of raw materials: cellulose fibers from renewable sources and polymer-based additives. The development of premium products with improved properties and functionalities depends on the optimization of both. This work focused on the combination of innovative experimental and computational strategies to optimize furnish. The main goal was to improve the functional properties of the most suitable raw materials for tissue materials and develop new differentiating products with innovative features. The experimental plan included as inputs different fiber mixtures, micro/nano fibrillated cellulose, and biopolymer additives, and enzymatic and mechanical process operations. We present an innovative tissue paper simulator, the SimTissue, that we have developed, to establish the correlations between the tissue paper process inputs and the end-use paper properties. Case studies with industrial interest are presented in which the tissue simulator was used to design tissue paper materials with different fiber mixtures, fiber modification treatments, micro/nano fibrillated cellulose, and biopolymer formulations, and to estimate tissue softness, strength, and absorption properties. The SimTissue was able to predict and optimize a broader range of formulations containing micro/nanocellulose fibers, biopolymer additives, and treated-fiber mixtures, saving laboratory and industrial resources. [ABSTRACT FROM AUTHOR]

Broussonetia papyrifera L. (paper mulberry) is an alternative woody plant, which can used to replace part of the protein feed for ruminants. Ensiling is an effective way to preserve fresh pasture and to solve the problem of stable storage and feed conversion of paper mulberry in the rapid growth period. However, low dry matter (DM), water-soluble carbohydrate, and lactic acid bacteria (LAB) reduce the quality of paper mulberry silage. This study assesses the influence of wilting time (0 h and 3.5 h; lighting: 3.43 × 104 Lux) and three additives (Enterococcus durans, CL; cellulase, CE; and formic acid, FA) on the fermentation quality, aerobic stability, and bacterial community of whole plant B. papyrifera silage. The whole plant B. papyrifera sample was mowed and wilted for 0 h and 3.5 h, and then had CL, CE, or FA added, followed by 60 days of ensiling. The results show all silage samples had high fermentation quality with pH below 4.2, ammonia-nitrogen below 100 g/kg DM, and no detectable butyric acid. The additives protected the DM and the crude protein from protease activity (p < 0.05), and CL was the most effective among them. Furthermore, wilting time influenced the silage’s bacterial communities, but overall, CL treatment had the greatest impact on bacterial communities. Wilting time and formic acid treatment significantly improved aerobic stability (p < 0.05). Enterococcus was positively correlated with lactic acid (LA), while negatively correlated with LA and Weissella (p < 0.001). Enterococcus was identified as the main driver of the whole plant paper mulberry ensiling process in the present study. In conclusion, compared to other additives, LAB is the most effective and economical to improve the fermentation quality and reduce the protein degradation of whole plant paper mulberry silage. Our findings provide a theoretical basis to improve the quality and production of paper mulberry silage.

Let M be a von Neumann algebra without direct commutative summands, and let A be an arbitrary subalgebra of LS (M) containing M, where LS (M) is the ∗-algebra of all locally measurable operators with respect to M. Suppose δ is an additive mapping from A to LS (M) that satisfies the condition δ(A)B ∗ + Aδ(B) + δ(B)A ∗ + Bδ(A) = 0 whenever AB = BA = 0. In this paper, we prove that there exists an element Y in LS (M) such that δ(X) = XY - YX∗, for every X in A. [ABSTRACT FROM AUTHOR]

Step selection functions (SSFs) are used to jointly describe animal movement patterns and habitat preferences. Recent work has extended this framework to model inter‐individual differences, account for unexplained structure in animals' space use and capture temporally varying patterns of movement and habitat selection.In this paper, we formulate SSFs with penalised smooths (similar to generalised additive models) to unify new and existing extensions, and conveniently implement the models in the popular, open‐source mgcv R package.We explore non‐linear patterns of movement and habitat selection, and use the equivalence between penalised smoothing splines and random effects to implement individual‐level and spatial random effects. This framework can also be used to fit varying‐coefficient models to account for temporally or spatially heterogeneous patterns of selection (e.g. resulting from behavioural variation), or any other non‐linear interactions between drivers of the animal's movement decisions.We provide the necessary technical details to understand several key special cases of smooths and their implementation in mgcv, showcase the ecological relevance using two illustrative examples and provide R code to facilitate the adoption of these methods. This paper offers a broad overview of how smooth effects can be applied to increase the flexibility and biological realism of SSFs. [ABSTRACT FROM AUTHOR]

Additive technology (AT) has emerged as a key enabling technology, with its ability to shorten product design and development time. The paper presents the programming and program verification using machine simulation of additive manufacturing tool path in CAD/CAM and Vericut environment. A procedure for configuring and preparing of a virtual machine for several additive process simulations has been proposed. The paper analyses the available programming software for generating G code from the STL file as well as the possibility of simulating the virtual machine when working according to the generated program. [ABSTRACT FROM AUTHOR]

Purpose: The digital transition process is an important strategic initiative for manufacturing companies to ensure continued competitiveness. The purpose is to investigate the relationship between firms' additive manufacturing (AM) readiness and product and process innovation and how this process is mediated by firms' make-or-buy decisions regarding performing AM processes internally or buying AM services from external partners. Design/methodology/approach: The paper is based on a questionnaire survey including full answers from 157 small- and medium-sized manufacturing companies. Findings: Results show a positive relationship between AM readiness and both product and process innovation. Results also reveal that firms with higher readiness invest more in in-house AM, which in turn promotes innovation. There was no significant association between AM readiness and the use of external AM services. Nonetheless, buying external AM services is still associated positively with innovation. Research limitations/implications: Data in the questionnaire survey are provided by single respondents from each company and are only based on Danish respondents. Practical implications: The results indicate that firms' product and process innovation benefits from higher AM readiness derive from increased investment in in-house AM rather than from increased use of external AM services. This also signifies that firms with lower levels of AM readiness buy external AM services and derive the innovation benefits hereof. Originality/value: The paper delivers new, empirically found knowledge about how small- and medium-sized manufacturing can improve innovation by both making and buying AM services. [ABSTRACT FROM AUTHOR]

The field of nanotechnology has shown promise in addressing major problems and improving drilling effectiveness. An overview of the difficulties encountered during oil and gas well drilling operations and the demand for creative solutions opens the debate. This review explores how nanotechnology is transforming the oil industry and enhancing performance as a whole. The evaluation of the uses of nanotechnology for better oil recovery, real-time monitoring, innovative materials, drilling fluids, and reservoir characterization are extensively discussed in this review. The primary function of additives is to improve the fundamental characteristics of drilling fluids. The variety of fluid additives available is a reflection of the complex drilling–fluid systems that are currently being used to enable drilling in increasingly difficult subsurface conditions. Common additives used in water- and oil-based drilling fluids include lubrication, shale stability, filtration control, rheology control, viscosification, and pH regulation. Drilling fluids frequently contain filtration control additives such as starch, polyanionic cellulose (PAC), carboxymethyl cellulose (CMC), and nanoparticles (NP). Commonly used rheology-modifier additives are xanthan gum, carboxymethyl cellulose, guar gum powder, and, more recently, salt-responsive zwitterionic polymers that were used as viscosifiers to water-based drilling fluids. The three main additives that regulate pH are citric acid monohydrate, potassium hydroxide, and sodium hydroxide. Additives that stabilize shale, such as potassium and sodium salts and asphaltenes, are often used. A wide range of materials are included in the category of lubricating additives, including polymers, asphaltenes, glass beads, oils of various grades, and oil-surfactants. Various fibrous materials, including wood, cotton, fibrous minerals, shredded tires from vehicles, and paper pulp, are used as additives to control circulation. Furthermore, shredded cellophane, bits of plastic laminate, plate-like minerals like mica flakes, granulated inert materials such as nut shells, and nano-polymers are used in wellbores to reduce fluid loss. The incorporation of nanoparticles into drilling fluids has produced upgraded fluids with better features, including improved lubricity, thermal stability, and filtering capacities. These developments aid in lowering friction, enhancing wellbore stability, and enhancing drilling efficiency. This paper also emphasizes how nanotechnology has made enhanced drilling equipment and materials possible. Drilling equipment's longevity and performance are increased by nanocomposite materials that have been reinforced with nanoparticles due to their improved mechanical strength, wear resistance, and thermal stability. Advanced reservoir characterisation tools, including nanoparticle tracers and nanoscale imaging methods, can help locate the best drilling sites and increase production effectiveness. On the other hand, nanofluids and nanoemulsions can potentially increase oil recovery because they enhance fluid mobility, lower interfacial tension, and alter rock wettability. Although nanotechnology has many advantages, there are also issues that need to be resolved. For an implementation to be effective, factors including nanoparticle stability, dispersion, and potential environmental effects must be carefully taken into account. This review highlights the need for future research to create scalable manufacturing procedures, improve nanoparticle behaviour, and determine nanomaterials' long-term environmental effects. In conclusion, this in-depth analysis illustrates the use of nanotechnology in transforming the process of drilling oil and gas wells. [ABSTRACT FROM AUTHOR]

Coal remains an important fuel for use in thermal power plants. However, coal-burning power plants produce large amounts of CFA, which contains TEs such as B, F, and Se, which are leached upon contact with water and act as potential polluters of aquifer systems and soil. To study the transformation of TEs, a thermodynamic calculation (FactSage 7.2) was used. Paper sludge ash was used as a calcium compound additive. The influence of blending a high-calcium additive on the environmental safety of TEs was investigated based on the effect of the mass addition ratio of PS ash. This study's results confirmed that the leaching processes of TEs, namely (CaO)2(Al2O3), CaF2, Ca10(PO4)F2, and CaSeO4(H2O)2, were caused by the formation of B, F, and Se compounds during the leaching process. Thus, it is clear that calcium has the greatest influence on the transformation of TEs due to their reaction, which, in turn, minimizes the effects of the TEs' release into the environment. The concentrations of TEs from the sample and addition of PS ash decreased slightly, indicating that the inhibition of TEs was enabled through the addition of PS ash. Although the PS ash YB had the highest calcium content, the PS ash YC gave the best results during the B and Se inhibition processes. The experimental observation was also evaluated for comparison. For the analysis of TEs' leaching ratios using the thermodynamic calculation and experiment, the experimental results were lower than those initially predicted. These results will help us to choose the best available control technology to minimize the effects of TEs released into the environment. [ABSTRACT FROM AUTHOR]

Passive recognition of ship-radiated noise plays a crucial role in military and economic domains. However, underwater environments pose significant challenges due to inherent noise, reverberation, and time-varying acoustic channels. This paper introduces a novel approach for ship target recognition and classification by leveraging the power of three-dimensional (3D) Melspectrograms and an additive attention based Transformer (ADDTr). The proposed method utilizes 3D Mel-spectrograms to capture the temporal variations in both target signal and ambient noise, thereby enhancing both categories’ distinguishable characteristics. By incorporating an additional spatial dimension, the modeling of reverberation effects becomes possible. Through analysis of spatial patterns and changes within the spectrograms, distortions caused by reverberation can be estimated and compensated, so that the clarity of the target signals can be improved. The proposed ADDTr leverages an additive attention mechanism to focus on informative acoustic features while suppressing the influence of noisy or distorted components. This attention-based approach not only enhances the discriminative power of the model but also accelerates the recognition process. It efficiently captures both temporal and spatial dependencies, enabling accurate analysis of complex acoustic signals and precise predictions. Comprehensive comparisons with state-of-the-art acoustic target recognition models on the ShipsEar dataset demonstrate the superiority of the proposed ADDTr approach. Achieving an accuracy of 96.82% with the lowest computation costs, ADDTr outperforms other models. [ABSTRACT FROM AUTHOR]

Additives, such as antioxidants (AOs), carbon black (CB) and compatibilizers (COs), are used in recycled polymer blends for different reasons. AOs slow thermal degradation, CB gives blends a black color and protect them against ultraviolet (UV) light, and compatibilizers improve compatibility between the different phases of the mixture and consequently enhance the mechanical properties of the final blend. In this paper, the three additives were added to recycled polyethylene (PE) blends to study their effect on the final properties and to determine the best formulations that help improve the mechanical properties of recycled PE blends. Stress Crack Resistance (SCR) was accessed by performing Notched Crack Ligament Stress (NCLS) and Un-notched Crack Ligament Stress (UCLS). On the other hand, Oxidative Induction Time (OIT) was used to determine the oxidation time of the blends and the effect of each additive on this property. Based on the results of this study, it was proven that adding carbon black and antioxidants delay the thermal degradation of recycled PE blends and consequently improve the OIT. Otherwise, resistance to stress cracking is improved only by adding a compatibilizer to the reference blend. [ABSTRACT FROM AUTHOR]

In this paper, we provide improvements in the additive constant of the current best asymptotic upper bound for the maximum number of halving lines for planar sets of n points, where n is an even number. We also improve this current best upper bound for small values of n, namely, 106 ≤ n ≤ 336 . To obtain this enhancements, we provide lower bounds for the sum of the squares of the degrees of the vertices of a graph related to the halving lines. [ABSTRACT FROM AUTHOR]

(n , m , t) -Homomorphic Secret Sharing (HSS) allows n clients to share data secretly to m servers, which compute a function f homomorphically on the received secretly shared data while restricting the input data acquired by a collection of t servers to private ones. In Verifiable Homomorphic Secret Sharing (VHSS), if there are partially colluding malicious servers submitting erroneous computation results to the client, such erroneous computation results will be rejected by the client. In traditional static homomorphic secret sharing schemes, once a secret share of raw data is assigned to a group of servers, then all servers in the group must participate in the computation, which means that the computation has to be restarted once some servers fail to perform the task. In order to solve the above problem, we propose the first dynamic homomorphic secret sharing scheme for additive computation in this paper. In our scheme, once some servers fail, there is no need to recalculate the secret sharing but only the need to reissue the index set of servers that perform the computation, Our structure assigns more computation to the servers, which is very useful in real scenarios. In addition, we propose dynamic verifiable homomorphic secret sharing schemes based on the above schemes, which have less computational overhead compared to the existing schemes, although we sacrifice the public verifiability property. Finally, we give a detailed correctness, security, and verifiability analysis of the two proposed schemes and provide the theoretical and experimental evaluation results of the computational overhead. [ABSTRACT FROM AUTHOR]

Alkaline–surfactant–polymer (ASP) flooding by means of which alkali additives, surfactant and polymer are inserted as the same slug is one of the most favourable worldwide focuses of Chemical Enhanced Oil Recovery (cEOR) research and field trials, due to the individual synergy of the three chemical components. To develop efficient oil recovery chemicals, it is essential to fully understand the mechanism behind ASP flooding. Nonetheless, there are hardly any studies reporting a systematic characterization of the ASP process. Thus, the present paper focuses on modelling this process in a laboratory by the use of an anionic surfactant—sodium dodecyl sulphate (SDS) in alkaline–polymer media—which is composed of a commercial water-soluble polymer (Flopaam AN125SH®, SNF Floerger, Andrézieux-Bouthéon, France) and alkali compounds (NaOH and Na2CO3). The samples were characterized using rheometry, dynamic light scattering (DLS), infrared spectroscopy (IR) and measurement of inferfacial tension (IFT) between the samples and rapeseed oil. In accordance with the experimental results, surprisingly lower IFT values were recorded between the alkaline–polymer solutions and rapeseed oil than the samples which contained SDS. Increasing polymer and sodium chloride concentration caused a decrease (from 0.591 mN/m to 0.0486 mN/m) in IFT between the surfactant containing samples and rapeseed oil. The IR measurements confirmed that the surfactant was not detected in the oil phase in the absence of NaOH and Na2CO3. The effects of SDS on the viscosity of the mixtures were also investigated, as viscosity is a considerably important parameter in processes using polymers. [ABSTRACT FROM AUTHOR]

In this paper, we propose a new class of systemic risk measures, which we refer to as strong comonotonic additive systemic risk measures. First, we introduce the notion of strong comonotonic additive systemic risk measures by proposing new axioms. Second, we establish a structural decomposition for strong comonotonic additive systemic risk measures. Third, when both the single-firm risk measure and the aggregation function in the structural decomposition are convex, we also provide a dual representation for it. Last, examples are given to illustrate the proposed systemic risk measures. Comparisons with existing systemic risk measures are also provided. [ABSTRACT FROM AUTHOR]

This paper presents a strength-based simultaneous optimization method for optimizing thermoelastic structural topology and print direction in the presence of anisotropy induced by additive manufacturing. The approach utilizes the bi-directional evolutionary structural optimization framework and defines design variables including element density and print-off angle. Firstly, an anisotropic thermoelastic constitutive model is established for finite element analysis. By introducing the Tsai–Hill failure criteria, the strength constraint to evaluate the stress level of additively manufactured anisotropic components is formulated. The P-norm aggregation function is employed to approximate the maximum strength failure coefficient. Then, the aggregated strength constraint is augmented to the optimization objective through a Lagrange multiplier. Sensitivity analysis of the new objective function with respect to the elemental design variables is performed, and an analytical approach is proposed to optimize the print-off angle. To improve the stability of the optimization procedure, a series of numerical algorithms and parameter updating strategies are developed. The effectiveness of our proposed method is demonstrated through typical numerical examples, highlighting a desirable match between the structural topology and the print direction can greatly improve the structural performance. [ABSTRACT FROM AUTHOR]

In the preparation of the slurry in the slurry shield (SSS) and subsequent reduction of the waste slurry produced by the slurry shield (WSSS), the additives in SSS improve the quality of filtration cake on the excavation surface, but they may also remain in WSSS, which have a negative impact on the reduction efficiency of WSSS. Therefore, it is valuable to establish the relationship between SSS and WSSS with additives as a link. Given this, this paper prepared WSSS with different dosages of additives and studied the influence of residual additives on the reduction. The residual additives made the reduction efficiency of WSSS worse, and the specific resistance to filtration increased by one to two orders of magnitude. The residual additives change the content of bound water or reduce the available sites of the soil particles that can be adsorbed by flocculants, leading to worse reduction results. To reduce the difficulty of reduction, combining polymer and bentonite as additives are recommended to prepare SSS. Polyaluminium chloride (PAC) acts by reducing bound water content through the interaction with residual bentonite, simultaneously augmenting PAM flocculation, which is recommended for reducing WSSS. This paper provides a reference for selecting materials used to prepare SSS and the subsequent reduction of WSSS. [ABSTRACT FROM AUTHOR]

Wellbore instability is an issue that, if left untreated, can cause wells to collapse, resulting in human, environmental, equipment, and revenue losses. Drilling fluids have been used to enhance the drilling process by lubricating and cooling the drill bit, eliminating cuttings, and most importantly, by improving the stability of the well by preventing fluid loss. However, there has been an increase in operational demands and challenges that call for drilling fluids to be more effective, economical, sustainable, and environmentally friendly. With shales that have infinitesimally small pores, nanoparticle additives in drilling fluids can be crucial in providing the properties that are necessary to prevent fluid loss and provide wellbore stability while meeting the operational demands of the present day. Therefore, this paper examines the use of nanoparticle additives including copper (II) oxide (CuO), magnesium oxide (MgO), and aluminum oxide (Al2O3) where they are tested under three conditions using the permeable plugging tester (PPT), high-temperature high-pressure (HTHP) fluid loss apparatus, and API low-temperature e low-pressure (LTLP) fluid loss apparatus under concentrations of 0.03% and 0.10%. Finally, based on the results, each nanoparticle sample (particle sizes between one and 100 nm) performed well in contributing to the aim of this project. CuO is the most effective inhibitor across all concentrations and under the three different conditions. It contributed to reducing the fluid loss from 37.6 mL to 18.2 and 13.2 mL, which is between 52% and 65% of fluid reduction. For MgO, it contributed to fluid loss reduction to 23.8 mL and 15 mL, which translated to 37%e60% of fluid loss reduction. The use of Al2O3 nanoparticles resulted in a fluid loss reduction to 33.6 mL and 17.8 mL, reducing the fluid loss up to 11%, at HTHP and up to 53% at LTLP. Unlike CuO and MgO, Al2O3 was less effective under HTHP conditions when compared to LTLP conditions. Al2O3 did not suffer as a significant diminishing benefit with increasing concentration in LTLP conditions however which means that at a higher concentration, it may begin to be more effective. Each material used in this study has its own specific and technical characteristics that will help create a progressive amount of property, such as providing stability and withstanding the high-temperature and highpressure condition downhole. [ABSTRACT FROM AUTHOR]

In this paper, we study a new class of locally dominated orthogonally additive operators on lattice-normed spaces (LNS). In the first part of the paper, sufficient conditions for the existence of a local exact majorant of a locally dominated operator and formulas for its calculation are given. The second part shows that the -compactness of a dominated orthogonally additive operator acting from a decomposable lattice-normed space to a Banach space with mixed norm implies the -compactness of its exact majorant. [ABSTRACT FROM AUTHOR]

Linear codes achieving or nearly achieving the Singleton bound are interesting in both theory and practice. The objective of this paper is to construct several infinite families of MDS, near MDS and almost MDS codes from some special cyclic subgroups of ${\mathbb {F}}_{q^{2}}^{*}$. To this end, the augmentation and extension techniques are used. The codes in this paper have flexible parameters and their lengths could be large. The minimum linear locality of the codes constructed in this paper is also studied. Some infinite families of optimal linearly locally recoverable codes are obtained. Besides, some codes in this paper are proved to be proper for error detection. [ABSTRACT FROM AUTHOR]

Carbon nanofibers (CNFs) and graphene nanosheets (GNs) are introduced to obtain nano-sized TiC particles in a novel additive manufactured Ni-Co-based superalloy. The double strengthening effects of reaction-induced TiC and remaining CNFs/GNs are conceptualized in the present paper. The CNFs and GNs act as heterogeneous nucleation sites for the formation of uniformly distributed TiC nanoparticles, which inhibits the crack and homogenize the microstructure. Interestingly, the existence of remaining GNs/CNFs is revealed via 3D atom-by-atom tomographic reconstruction technology for the first time. This unique combination of nanoparticles and residual CNFs/GNs nanofillers has great potential to develop superalloys with excellent properties. The formation of nano-sized dispersion TiC particles is induced by the introduction of carbon nanofibers and graphene nanosheets in additive manufactured superalloy, which inhibits the crack and homogenizes the microstructure. [ABSTRACT FROM AUTHOR]

Empirical studies have emphasized that the equity implied volatility is characterized by a negative skew inversely proportional to the square root of the time-to-maturity. We examine the short-time-to-maturity behavior of the implied volatility smile for pure jump exponential additive processes. An excellent calibration of the equity volatility surfaces has been achieved by a class of these additive processes with power-law scaling. The two power-law scaling parameters are β , related to the variance of jumps, and δ , related to the smile asymmetry. It has been observed, in option market data, that β = 1 and δ = - 1 / 2 . In this paper, we prove that the implied volatility of these additive processes is consistent, in the short-time, with the equity market empirical characteristics if and only if β = 1 and δ = - 1 / 2 . [ABSTRACT FROM AUTHOR]

Increasing environmental concerns over using petroleum-based packaging materials in the food industry have encouraged researchers to produce edible food packaging materials from renewable sources. Biopolymer-based edible films and coatings can be implemented as bio-based packaging materials for prolonging the shelf life of food products. However, poor mechanical characteristics and high permeability for water vapor limit their practical applications. In this regard, plant oils (POs) as natural additives have a high potential to overcome certain shortcomings related to the functionality of edible packaging materials. In this paper, a summary of the effects of Pos as natural additives on different properties of edible films and coatings is presented. Moreover, the application of edible films and coatings containing POs for the preservation of different food products is also discussed. It has been found that incorporation of POs could result in improvements in packaging's barrier, antioxidant, and antimicrobial properties. Furthermore, the incorporation of POs could significantly improve the performance of edible packaging materials in preserving the quality attributes of various food products. Overall, the current review highlights the potential of POs as natural additives for application in edible food packaging materials. [ABSTRACT FROM AUTHOR]

It is often necessary to use stabilising additives during construction to improve the resulting soil properties to ensure the good quality of civil engineering structures. These additives are often produced at high temperatures and with a high carbon footprint. This paper focuses on soil stabilization with waste concrete slurry, which is produced during the production of fresh concrete. The selected clay soil was stabilized with cement and CSW at 2, 4, and 6% by weight of soil. Compressive strength, the resistance to freezing and thawing, Initial bearing index (IBI), and California bearing capacity (CBR) were monitored. The research did not confirm better performance of CSW binder even at higher dosage compared to cement, which was due to the high water content of the mixtures. Positive results were achieved especially in Freez-Thaw resistance. [ABSTRACT FROM AUTHOR]

Anaerobic digestion (AD) is a promising technology for renewable energy production from organic waste. In order to maximize the produced biogas quantity and quality, this paper deals with the optimization of the AD process in a CSTR bioreactor of a full-scale biogas plant. For this purpose, a novel approach was adopted coupling, a highly complex BioModel for AD simulation, and a gradient-based optimization method. In order to improve AD performance, the dosages of various types of biological additives, the dosages of inorganic additives, and the temperature in the bioreactor were optimized in three different scenarios. The best biogas quality was obtained using multi-objective optimization, where the objective function involves the following two conflicting objectives: the maximization of biogas production and minimization of the needed heating energy. The obtained results show that, potentially, the content of C H 4 can be increased by 11%, while the contents of H 2 , H 2 S , and N H 3 can be reduced by 30%, 20%, and 81% when comparing the simulation results with the experimental data. The obtained results confirm the usefulness of the proposed approach, which can easily be adapted or upgraded for other bioreactor types. [ABSTRACT FROM AUTHOR]

Let R be a 2−torsion free semiprime ring, α an automorphism and U a noncentral square-closed Lie ideal of R. An additive mapping T : R → R is called a left (resp. right) α−centralizer of R if T(xy) = T(x)α(y) (resp. T(xy) = α(x)T(y)) holds for all x, y ∈ R. In this paper, we proved the following result: i) If T (uvu) = α (u) T (v) α (u) for all u, v ∈ U, then T is a left α−centralizer, ii) If T(uvu) = T(u)α(vu) (resp. T(uvu) = α(uv)T(u)) for all u, v ∈ U, then T is a left (resp. right) α-centralizer on U. [ABSTRACT FROM AUTHOR]

In this paper, we solve the system of functional equations { f (x + y) + g (y − x) = 2 f (x) , g (x + y) − f (y − x) = 2 g (y) and we investigate the stability of g-derivations in Banach algebras. [ABSTRACT FROM AUTHOR]

In this work, the samples of the WC-Fe-Ni-Co composition were obtained and studied. Alloy NiCo 29-18 is used as a binder (Fe-Ni-Co). In this paper, a comparative analysis of the samples obtained using commercial micron-sized WC powder and the samples obtained is carried out using nano-WC synthesized via the electric explosion of wire (EEW) method. The samples were subjected to vacuum sintering, then their structure, density, and porosity, as well as microhardness and oxidation resistance, were studied. Five different additives were used to stabilize sintering: VC, Cr3C2, NbC, Y2O3, and Nd2O3. All these additives are described in the literature as additives that are used in the sintering of materials of the WC-Co system. Also, the samples from the WC-Fe-Ni-Co material were obtained using additive manufacturing technology with material extrusion. Bending strength and hardness of the additively fabricated samples were determined. [ABSTRACT FROM AUTHOR]

The growing interest in modern polymer materials has targeted research on complex plastic coatings and the possibilities of modifying their features and properties during manufacturing. Today's modern coatings, including polyurea and polyurethane, are among the most modern developed resins. Compared to other polymer coatings, they are distinguished by their versatility, strength, and durability. They undoubtedly represent the next step in the evolution of coatings. Advances in coating technology have also led to the development of spray, injection, and roto-cast application equipment, improving polyurea-based elastomers' performance. For many years, there has been much interest in increasing the flame resistance of polymers. This is dictated by safety considerations and the increasing requirements for the flammability of plastics, the area of application of which is growing every year. This text attempts to provide an overview of current research on flame retardant composites. Particular attention was paid to polyurea (PU) and polyurea-based hybrids and the application areas of polyurea coatings. The paper defines flame retardants, discusses how they work, and presents the types of flame retardants and the current trends of their usage in the production of plastics. [ABSTRACT FROM AUTHOR]

Large areas of estuarine deposits exist on the coastal plains of the southeast Queensland coast with a countered depth of up to 30 m. These deposits are categorized as sediments that originated during the Holocene Age. The sediments have not been consolidated or subjected to considerable pressure since the end of the Ice Age. The structure of these deposits consists of large ratios of porosity, causing high soil compressibility, which lowers the bearing capacity of the soils. Therefore, the soils of the region cannot maintain sufficient support for construction loads, and consequent malfunctions could occur in short-term and long-term periods. The objective of this paper is to investigate the suitability of new soil stabilization additives in the southeast Queensland region and the optimum additive content of cementitious materials and an advanced mixing modifier branded as DuraCrete. A combination of Portland cement and DuraCrete was used as a soil additive. Three DuraCrete-to-cement ratios were used: 2%, 3%, and 4% by weight. Soil collected from the Port of Brisbane region was treated by adding the additives as a percentage of its weight; four percentages were considered: 10%, 20%, 25%, and 30% for each combination of additives. The performance of the treated soils was examined under unconfined compression after 28 days of curing. The results revealed that increases in the unconfined compressive strength were detected as DuraCrete was added to the mixtures. For 30% additives, increases of about 15%, 34%, and 17% were detected when DuraCrete was added as 2%, 3%, and 4%, respectively. The results also revealed that 3% DuraCrete content provided significant stabilization compared to 2% and 4% for 25% and 30% additive-treated soils; such behavior was also observed for the specimens of 25% content of additives. Additionally, DuraCrete can be considered a promising material that can be combined with cement to obtain the desired stabilization of soft soils. [ABSTRACT FROM AUTHOR]

The electrolytic refining of crude tin is generally carried out in the fluorosilicic acid (H2SiF6) system with the assistance of bone glue and β-naphthol. However, the high saturated vapor pressure and low stability of H2SiF6 present environmental concerns and do not align with sustainable development goals. In this paper, the electrochemical behavior of tin on a glassy carbon (GC) electrode was studied in a relatively green and environmentally friendly methanesulfonic acid (MSA) system. Bone glue, sodium lignosulfonate, and β-naphthol were used as additives to make the deposit morphology smooth and to ensure grain refinement. The electrochemical reduction process of Sn2+ in an MSA system is a quasi-reversible process controlled by diffusion. The apparent activation energy E a = 14.189 kJ/mol for the ion diffusion of Sn2+ was further calculated. The results of chronoamperometry showed that the electrocrystallization of Sn2+ on the GC electrode gradually tended to three-dimensional instantaneous nucleation with the increase in applied potential. The morphology and phase of the deposits were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the deposits were uniform and dense pure tin. This work elucidates the electrochemical behavior of tin in a methanesulfonic acid system. [ABSTRACT FROM AUTHOR]

We analyze the forces that explain inflation using a panel of 122 countries from 1997 to 2015 with 37 regressors. Ninety-eight models motivated by economic theory are compared to a boosting algorithm, non-linearities and structural breaks are considered. We show that the typical estimation methods are likely to lead to fallacious policy conclusions, which motivates the use of a new approach that we propose in this paper. The boosting algorithm outperforms theory-based models. Furthermore, we extend the current software implementation of conditional Akaike Information Criteria for additive mixed models with observation weights. We present a novel two-step selection process suitable for a wide range of applications that enables to empirically compare theory- and data-driven models with varying data availability. [ABSTRACT FROM AUTHOR]

The archaeological pottery extracted from Tell Rawd Iskander in Ismailia is dated back to the New Kingdom. Different examinations and analyses were conducted, such as stereomicroscope examination, polarized microscope, microbiological examination, scanning electron microscope equipped with X-ray energy dispersion unit (SEM / EDX), and X-ray diffraction. The research identified a technological process proving that the clay used in archaeological pottery was Nile clay. Tempers were sand, pottery powder, limestone powder "calcite, dolomite", and burnt straw. The forming technique was the potter wheel technique. Surface treatment is a slip layer and red wash. The burning atmosphere inside the kiln was oxidizing for the first and second pottery objects, and it was reduced for the third pottery shard. The pottery texture was fine to coarse fabric. Furthermore, the research paper proved that pottery artifacts were subjected to various damage processes resulting from different environmental factors. Most damage manifestations were surface deformation by soil sediments, iron stains, soot, and fungal growth. Pottery objects also suffered from crystallization of salts "chlorides, sulfates, carbonates, and phosphates", cracking, fracture, weakness, gaps, peeling, separation of grains, and breaking. The archaeological pottery in Tell Rawd Iskander in Ismailia was treated. Hairbrushes removed free fragile sediments. Various metal scalpels cleaned firmly attached sediments. Furthermore, clay deposits were removed by a mixture of distilled water, acetone, and ethyl alcohol in a ratio of 1:1:1. EDTA cleaned lime deposits, whereas mora poultice extracted carbonate and gypsum salts. Fungal infections were treated by nano silver oxide (0.5 %). Strengthening archaeological pottery was carried out using nano-silica (0.5%); it was applied by the spraying method. Paralloid B 82 (50%) was used in assembling pottery shards. Replacement was conducted by a mixture of micro-ballon and pottery powder. [ABSTRACT FROM AUTHOR]

This paper examines the difference between the effects of anti-wear additives on vegetable and hydrocarbon-based oils. Knowledge of the specific influence of additives on the anti-wear properties of vegetable oils is necessary to increase the efficiency of the development of biodegradable lubricating oils. In addition, this is interesting from the point of view of clarifying the mechanism of action of AW/EP additives. The effect of non-toxic additives—adipic acid monoester and hexadecanol—on hydrocarbon hydrocracking oil and vegetable oil was compared. The comparison was carried out in rolling contact with sliding, sensitive to the separating ability of the oil. It was found that in hydrocarbon oil, the additive affects the parameters of the hydrodynamic friction regime. When adding an additive to vegetable oil, the hydrodynamic parameters do not change. The additive acts in the same way in both oils during mixed and transient modes. The obtained results are compared to available data, and an explanation of the difference is proposed based on the AW/EP mechanism of action. It is concluded that there is little chance of enhancing vegetable oil properties for hydrodynamic bearings. Search criteria for additives that effectively influence the antifriction and anti-wear properties of vegetable oils in mixed and boundary friction modes are proposed. [ABSTRACT FROM AUTHOR]

In the main result of this paper we prove a version of the well-known open mapping theorem for weakly additive, order-preserving operators between ordered real vector spaces with an order unit. We also provide a few examples to illustrate obtained results. [ABSTRACT FROM AUTHOR]

Plant-based meat analogues are food products made from vegetarian or vegan ingredients that are intended to mimic taste, texture and appearance of meat. They are becoming increasingly popular as people look for more sustainable and healthy protein sources. Furthermore, plant-based foods are marketed as foods with a low carbon footprint and represent a contribution of the consumers and the food industry to a cleaner and a climate-change-free Earth. Production processes of plant-based meat analogues often include technologies such as 3D printing, extrusion or shear cell where the ingredients have to be carefully picked because of their influence on structural and textural properties of the final product, and, in consequence, consumer perception and acceptance of the plant-based product. This review paper gives an extensive overview of meat analogue components, which affect the texture and the structure of the final product, discusses the complex interaction of those ingredients and reflects on numerous studies that have been performed in that area, but also emphasizes the need for future research and optimization of the mixture used in plant-based meat analogue production, as well as for optimization of the production process. [ABSTRACT FROM AUTHOR]

Conventional bitumen pavement is no longer suitable for handling increasing loads and weather variations, which cause road deterioration, Thus, the modification of bitumen has been suggested to counter this issue. This study provides a detailed assessment of various additives for modifying natural rubber-modified bitumen used in road construction. This work will focus on the use of additives with cup lump natural rubber (CLNR), which has recently started to gain attention among researchers, especially in rubber-producing countries such as Malaysia, Thailand and Indonesia. Furthermore, this paper aims to briefly review how the addition of additives or modifiers helps elevate the performance of bitumen by highlighting the significant properties of modified bitumen after the addition of modifiers. Moreover, the amount and method of application of each additive are discussed further to obtain the optimum value for future implementation. On the basis of past studies, this paper will review the utilisation of several types of additives, including polyphosphoric acid, Evotherm, mangosteen powder, trimethyl-quinoline and sulphur, and the application of xylene and toluene to ensure the homogeneity of the rubberised bitumen. Numerous studies were conducted to verify the performance of various types and compositions of additives, particularly in terms of physical and rheological properties. In general, additives enhance the properties of conventional bitumen. Future research should investigate CLNR because studies on its utilisation are limited. [ABSTRACT FROM AUTHOR]

Hierarchical organic structures have gained vast attention in the past decade owing to their great potential in chemical and medical applications in industries such as the food and pharmaceutical industries. In this paper, the crystallization of L-glu hierarchical spheres using inorganic ions, namely calcium, barium and strontium cations, is described. The anti-solvent precipitation method is used for the spherical crystallization. The L-glu microspheres are characterized using various techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photo-electron microscopy (XPS) and polarized microscopy (POM). It is shown that without additives, L-glu crystallizes as flower-like structures, very different from the hierarchical spheres crystallized with the charged additives. Based on our results, we suggest a mechanism for the hierarchical sphere formation based on the crystallization and self-assembly of L-glu in emulsion droplets using charged additives. [ABSTRACT FROM AUTHOR]

Biomass as an abundant "green" renewable and CO2 neutral energy source have captured the entire world attention as a result of worsening energy crisis and environmental problems. Combustion of biomass have huge potentials of producing heat and power in a sustainable way. However, biomass fuels possess alkali metals i.e potassium (K) content which react with other ash forming elements i.e chlorine (Cl) to form alkali containing species i.e potassium chloride (KCl) which results in ash related operational problems (slagging and fouling). Kaolin; an aluminum-silicate based additive is regarded as the best additive at handling and capturing the problematic alkali containing species during biomass combustion with its ability to convert alkali containing species to high melting point potassium aluminum silicates (Kalsilite, Leucite). Therefore, this paper presents an overview of the mechanism of ash deposition, highlight key findings of aluminosilicate-based additives applications from previous studies and ends with kaolin future perspective. [ABSTRACT FROM AUTHOR]

In this paper, we introduce two semiparametric single-index models for spatially and temporally correlated data. Our first model has spatially and temporally correlated random effects that are additive to the nonparametric function, which we refer to as the "semiparametric spatio-temporal single-index model (ST-SIM)". The second model integrates the spatially correlated effects into the nonparametric function, and the time random effects are additive to the single-index function. We refer to our second model as the "semiparametric integrated spatio-temporal single-index model (IST-SIM)". Two algorithms based on a Markov chain expectation maximization are introduced to simultaneously estimate the model parameters, spatial effects, and time effects of the two models. We compare the performance of our models using several simulation studies. The proposed models are then applied to mortality data from six major cities in South Korea. Our results suggest that IST-SIM (1) is more flexible than ST-SIM because the former can estimate various nonparametric functions for different locations, while ST-SIM enforces the mortality functions having the same shape over locations; (2) provides better estimation and prediction, and (3) does not need restrictions for the single-index coefficients to fix the identifiability problem. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) technology is extensively applied in various industries, including manufacturing, and is constantly advancing. Compared with subtractive manufacturing methods such as cutting or grinding, the AM is a cost-effective technique with minimal material wastage, and it can produce intricate shapes within a short timeframe. However, research on AM methods involving additional modeling or printing on the surfaces of three-dimensional objects is insufficient. By employing additive modeling, a diverse range of colors and materials can be utilized without requiring support structures, thereby expanding the possibilities of layering-based expression. This study experimentally investigated additive printing systems using a six-degree-of-freedom parallel mechanism stage and a fixed material extrusion head. A slant direct-drive parallel mechanism for a prototype additive printing system was proposed and designed. The developed prototype system enables additional modeling on curved and spherical surfaces of three-dimensional objects. An experimental surface modeling on these objects was conducted. This paper reports on the performance of the motion mechanism, motion range, and positioning accuracy of the modeling stage. Furthermore, the fabricated models were experimentally examined and validated to assess the results of the modeling process. [ABSTRACT FROM AUTHOR]

This paper presents experimental results on the influence of concrete composition factors on the criterion characterizing the ratio between the compressive strength of activated low-cement concrete and clinker consumption. The investigation was carried out using mathematical planning of the experiments. Experimental and statistical models describing the influence of the fly ash, activating additive (microsilica), consumption of cement and aggregates, as well as the superplasticizer on the strength of low-cement concrete under normal hardening conditions and after steaming were obtained. The values of the clinker efficiency criterion and the mineral additive cementing efficiency coefficient were calculated, and models of these parameters were obtained for the investigated concrete compositions. It was shown that the activating effect of microsilica yields an increase in ash cementing efficiency and clinker efficiency criterion in concrete. Using the obtained models, an example for calculating the ash cementing efficiency coefficient is given. [ABSTRACT FROM AUTHOR]