Search

[Display omitted] Gas hydrates have gained great interest in the energy and environmental field as a medium for gas storage and transport, gas separation, and carbon dioxide sequestration. The presence of small doses of surfactants in the aqueous phase has been reported to enhance hydrate formation; however, the underlying mechanisms remain poorly understood. Thus, in situ high-resolution X-ray computed tomography measurements were performed to monitor the upward water migration and the resulting hydrate nucleation and growth. It was found that the presence of hydrate crystals at the gas–liquid–solid contact line triggered the enhanced growth of hydrates on the reactor wall. A time delay was observed between the disappearance of the bulk water reservoir and its transformation into hydrate. The lower interfacial tension between the hydrate surface and the solution facilitated its adsorption onto the reactor wall once a thin film of hydrate nucleated on the solid wall surface. These hydrate layers present on the reactor wall were found to be porous, wherein the porosity decreased with increased subcooling. These fundamental results will be of value in understanding the mechanism of hydrate growth in the presence of surfactants and its potential application in hydrate-based technologies. [ABSTRACT FROM AUTHOR]

• 3D xenon hydrate shell meshes on water particle and ice sphere created from micro XCT. • Time-dependent hydrate shell thickness and inner/outer diameter were determined. • Novel 3D mesh method can quantify heterogeneous hydrate shell growth. Gas hydrates have gained increasing attention in energy and environmental fields and have potential applications in gas storage and transport, carbon dioxide sequestration, and flow assurance. Nevertheless, the kinetics of hydrate formation are still not well understood. In situ high-resolution X-ray computed tomography measurements were performed to monitor xenon hydrate formation on water droplets and ice spheres. For the first time, three-dimensional thickness meshes were used to quantify and visualize the kinetics of hydrate formation. The evolution of the hydrate morphology was investigated, and the time-dependent kinetic parameters were obtained, including the hydrate shell thickness and inner and outer diameters and the effective volume fraction of hydrate particles. The results indicate that the formation of gas hydrates undergoes an initial reaction-controlled stage followed by a mass-transfer-limited growth stage. For hydrate formation from a water droplet with an initial diameter of 1.66 mm, the hydrate shell thickness was approximately 30 μm and the effective volume fraction of hydrate particles was approximately 11% at 12 h after hydrate formation began. The standard deviation of the shell thickness, which indicates the surface roughness of the hydrate shell, increased with time for hydrate formation from water droplets. The results presented in this study renew our knowledge on the kinetics of hydrate formation, which is essential for their use in flow assurance and other hydrate-related technologies. [ABSTRACT FROM AUTHOR]

[Display omitted] • An approach of warm brine injection to promote CH 4 /CO 2 replacement is proposed. • Warm brine injection provides a 2.0 times enhancement of the cumulative gas yield. • A potential risk of hydrate reformation is alleviated by increasing salinity. • Gas production is insensitive to injected heat as the significant heat loss. • Brine injection scheme should be optimized based on energy harvest and CO 2 storage. CH 4 /CO 2 replacement for natural gas hydrates (NGHs) exploitation is a promising method for CO 2 geological sequestration and energy recovery simultaneously. However, the puzzles of low replacement efficiency and slow reaction rate caused by the mass transfer obstacle of gas exchange are fatal bottlenecks for field application of gas replacement method. Therefore, we propose a method that uses warm brine injection during CH 4 /CO 2 replacement process to break the barrier of CO 2 diffusion and enhance CH 4 recovery as well as CO 2 storage. Benefiting from the synergistic influence of salt effect and thermal stimulation as well as water flow erosion, warm brine injection provides three dimensionally connected channels in hydrate for subsequent mass transfer, improving CH 4 /CO 2 replacement in the deep layer of hydrate. CO 2 sequestration efficiency of the newly proposed method reaches 76.46%, and the maximum amounts of CH 4 recovery is nearly treble than that achieved by single CO 2 replacement method. Notably, a potential risk of secondary hydrate formation could occur upon the pressure surge and fluid migration attached to warm brine injection, which could be effectively alleviated by increasing salinity to destabilize hydrate lattices by reducing water activity. The gas production is insensitive to the injected heat as the significant heat loss during the transportation of injected brine in pipelines and thermal diffusion through boundaries. The introduction of free water increases the complexity of the reactions in hydrate reservoirs, and the formulation of brine injection regimes should be synergistically optimized based on energy harvest, energy efficiency and CO 2 sequestration. This work extends the previous knowledge on CH 4 /CO 2 replacement and shows important practical significance for future field studies of NGHs exploitation and CO 2 geological sequestration. [ABSTRACT FROM AUTHOR]