Search

• Unique 0.1 mm/pixel IR thermography diagnostic for plasma-wall interaction studies. • Improved accuracy and reliability on field of view positioning. • Operational on WEST tokamak since 2020. • Diagnostic is accurate to the monoblock. The Very High spatial Resolution (VHR) infrared thermography diagnostic developed by CEA-IRFM is installed in the WEST tokamak to measure surface temperature of the actively cooled W-monoblocks (MB) of the Plasma Facing Units (PFUs), which are similar to the International Thermonuclear Experimental Reactor (ITER) ones. It is a major diagnostic to investigate the behavior of PFU during experimentation thanks to its very high spatial resolution (0.1 mm / pixel), movable field of view (FoV) and the wide-range temperature measurement. In particular, it can study the evolution of monoblocks mounted in the tokamak, the influence of the shaping of these components submitted to high heat load and the behavior of the leading edges regarding the assembling tolerances between adjacent monoblocks. Finally, such diagnostic directly contributes to the specification assessment of the ITER divertor units. This diagnostic was operational during the 2019 WEST experimentation and its enhanced design for the 2020 WEST experimentation campaign. In order to monitor 30 × 12 mm monoblocks temperature, the VHR IR diagnostic is able to move its narrow FoV (64 × 51 mm) to specific targets on the observable divertor area (360 × 420 mm). Position and focus steering are achieved through motor-controlled mirrors and lenses operated by a dedicated Labview application on a remote unit. Mirror positioning occurs between pulses under normal WEST operation conditions, and can withstand thermal radiation and disruptions during pulses. Repeatability, hysteresis, mechanical components reliability are critical parameters to provide accurate positioning (<1 mm) of the FoV. The tuning and calibration of these actuators in accordance with WEST environment is crucial to guarantee the best position of the FoV and optical performances. This paper gives the FoV positioning implementation details and performance of the VHR in WEST. [ABSTRACT FROM AUTHOR]

ITER (www.iter.org) will take advantage of tungsten (W) actively cooled plasma facing units (PFUs) in the lower divertor. These PFUs will receive a steady state plasma heat flux of 10 MW m−2 and up to 20 MW m−2 in slow transients, pushing these components to their limit. For machine protection reasons and for the study of the plasma wall interactions, temperature measurements are foreseen with mid wave infra-red (MWIR: 3–5 μm) thermography systems to cover most of the ITER chamber, including the divertor (tungsten material) and first wall (beryllium material) [1]. Absolute temperature measurements from 70 °C and the cooling temperature of the PFUs, up to 3500 °C (W melting temperature at 3422 °C), are considered. Those measurements require knowledge of the emissivity of the tungsten PFU surfaces as a function of the temperature and wavelength used for the IR monochrome thermography system. This paper summarizes the emissivity measurements performed on tungsten surfaces in high heat flux test beds and the WEST tokamak [2] and uses the experimental emissivity values to compute the expected uncertainties in ITER (ΔT/T) using monochrome and bicolor thermography techniques. The results show that the monochrome technique is not able to fulfill the ΔT/T < 10% requirement, while the bicolor technique is able to reduce the temperature uncertainty below 10%. Laboratory bicolor thermography measurements using a filter wheel (including six MWIR interference filters) have been successfully performed up to 830 °C with temperature uncertainty ΔT/T < 3%. In the WEST tokamak, the two dimensions emissivity map is varying by a factor of five within 27 cm along a PFU, from 0.13 to 0.65, showing that the monochrome IR thermography will have difficulties staying within the ITER requirements ΔT/T < 10% from 70 °C up to 3500 °C. [ABSTRACT FROM AUTHOR]

• We presented the WEST full tungsten actively cooled divertor, mentioning its relevance with the ITER one. • Main features including key elements related to the large-scale production, the reception tests, and the installation into the WEST tokamak are reported. • Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted. • Results related to the assessment of heat removal capability by IR-thermography and high heat flux test are discussed. The WEST (W - for tungsten - Environment in Steady-state Tokamak) platform aims to support the ITER tungsten divertor technology, manufacturing and long pulse operation. For this purpose, the Tore Supra tokamak has been deeply modified (mainly the installation of a lower and upper divertor coil structure), enabling a restart in 2016 and a first phase of operation (Phase I) until the end of 2020. Following this first phase, a limited number of actively cooled PFUs (Plasma Facing Units), based on ITER divertor technology, were industrially produced and implemented into the WEST vacuum vessel. The second phase of operation (Phase II) will be with a full actively cooled divertor. The first WEST experimental campaign with this new configuration (Phase II) started in 2022. This paper reports on the key elements related to the large-scale industrial production, the reception tests, and the installation of the ITER-like divertor components (including embedded instrumentation) into the WEST tokamak. Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted, mentioning its relevance with ITER divertor specifications. Results related to the assessment of heat removal capability by IR thermography examination and high heat flux test, as well as the He-leak tightness control are also discussed. [ABSTRACT FROM AUTHOR]