Search

For an inductive power transfer (IPT) system, mobility is one of the most attractive features, but coupling variations can dramatically affect the system's output. In this article, a reconfigurable rectifier-based detuned series-series (SS) compensated IPT system is proposed to tolerate an extensive coupling range and improve the system efficiency simultaneously. The reconfigurable rectifier, which can operate in a full-bridge rectifier mode or a half-bridge rectifier mode, is used to alter the equivalent ac load from one value to the other so the expected coupling range of the detuned SS topology can be extended. At the same time, the system efficiency is also partly improved because the ac load is changed to get closer to the optimal load of the IPT system. First, a detuned SS IPT system with the reconfigurable rectifier is presented and followed by the analysis of the working modes. Then, a detailed parameter design process and switching control of the reconfigurable rectifier are introduced. Finally, a 400-W prototype was constructed to verify the validity of the proposed method. The experimental results demonstrate that the output power fluctuation of the proposed IPT system is less than 17.5% and the lowest efficiency can be improved from 68.6% to 87.5% with the coupling coefficient varying from 0.1 to 0.4. The proposed method can implement significant antimisalignment and efficiency improvement simultaneously, and it is regarded as a potential solution for low-power IPT applications with high spatial mobility. [ABSTRACT FROM AUTHOR]

To increase the power density of a wireless power transfer (WPT) system, the coupling of coils can be strong. However, in a strongly coupled series–series WPT system with a diode rectifier, currents can be distorted and discontinuous, and first harmonic approximation is no longer valid. The inverter is likely to work in hard switching, leading to extra noise, decreased efficiency, and a potential hazard for a safe operation. Through time-domain analysis, this article reveals that with a dual-side 90° phase shift, the hard switching of the inverter can be avoided, the power level can be enhanced, and the discontinuous conduction mode can be avoided to eliminate noises. The factors impacting the soft switching operations of the inverter and the rectifier are analyzed. To achieve 90° dual-side phase shift, the conventional approach of using the receiver voltage/current, which can be distorted and discontinuous in strongly coupled WPT systems, for phase synchronization is no longer suitable. A new set of coils, namely driving coils, is used for phase synchronization so that dual-side phase shift can be implemented independent from power transfer. Experimental results have validated the effectiveness of the analysis. [ABSTRACT FROM AUTHOR]

A wide operating region of inductive power transfer systems indicates a stable output against large load and coupling changes. In most of the published works, output regulation is achieved by single-side regulation that utilizes either primary-side or secondary-side power converters for load regulation. However, secondary-side regulation tends to have a relatively narrow operating region due to space and cost considerations. Meanwhile, although primary-side regulation may provide a larger operating region, system performance can be degraded due to the needs of secondary-side information. To overcome the drawbacks of single-side regulation, this article proposes a dual-side cooperative output regulation method implemented by burst-mode pulse density modulation. In the proposed method, dual-side cooperative control is established by sensing primary-side current drops caused by secondary-side burst operations and, hence, requires no communication devices. With the proposed method, the system operating region can be effectively extended without sacrificing steady-state performance. Experimental results are provided in this article to validate the proposed method. [ABSTRACT FROM AUTHOR]

In inductive power transfer systems, impedance matching is critical in obtaining high efficiency. However, since the load impedance is subject to variations in most applications, especially wireless charging, maintaining impedance matching is a challenge. One valid solution is to maintain the equivalent load impedance at the optimal value against load variations by controlling a load-side power converter. Nonetheless, the system overall cost, size, and complexity can be increased. In this article, based on a proper selection between full-bridge and half-bridge modes of the inverter and rectifier, an operation mode selection method is proposed that can achieve semi-impedance-matching with large load variations. In general, with the proposed method, high overall efficiency can be obtained while neither additional power converters nor complicated control is required. A 1-kW prototype has been developed and the experimental results have verified the proposed method. [ABSTRACT FROM AUTHOR]

Maximum efficiency point tracking (MEPT) control has been adopted in state-of-the-art wireless power transfer (WPT) systems to meet the power demands with the highest efficiency against coupling and load variations. Conventional MEPT implementations use dc/dc converters on both transmitting and receiving sides to regulate the output voltage and maximize the system efficiency at the expense of increased overall complexity and power losses on the dc/dc converters. Other implementations use phase-shift control or on–off control of the transmitting side inverter and the receiving side active rectifier instead of dc/dc converters but cause new problems, e.g., hard switching, low average efficiency, and large dc voltage ripples. This paper proposes a pulse density modulation (PDM) based implementation for MEPT to eliminate all the mentioned disadvantages of existing implementations. Delta-sigma modulators are used as an example to realize the PDM. A dual-side soft switching technique is proposed for the PDM. The ripple factor of the output voltage with PDM is derived. A 50 W WPT system is built to validate the proposed method. The system efficiency is maintained higher than 70% for various load resistances when the power transfer distance is 0.5 m, which is 1.67 times the diameter of the coils. [ABSTRACT FROM AUTHOR]