Search

[Display omitted] • An acid–induced dispersive liquid–liquid microextraction is developed. • Analytes are extracted by in situ formation of deep eutectic solvents with formed fatty acids. • The method is successfully used for detection of bisphenol A and alkylphenols. • The method is simple, rapid, sensitive, low cost, and environmentally friendly. • The new method expands the application pathway and scope of deep eutectic solvents. This study describes the development of an acid induced dispersive liquid–liquid microextraction method based on the in situ formation of hydrophobic deep eutectic solvents for the extraction of bisphenol A and alkylphenols from environmental water and beverage samples. Hydrochloric acid altered the hydrophilic-hydrophobic state of fatty acid salts to obtain hydrophobic fatty acids, which formed hydrophobic deep eutectic solvents with analytes in situ to extract the analytes. Under optimized conditions, the limits of detection and limits of quantitation were 0.03–0.1 μg L-1 and 0.12–0.3 μg L-1, the intraday and interday relative standard deviations were less than 3.9 %, and the enrichment factor was 29–32. The recoveries of bisphenol A and alkylphenols were 95.9–104.9 % and 86.9–105.0 %, respectively. The extraction process used only hydrochloric acid and fatty acid salts, and the extraction process required less than 1 min. This method has the advantages of simplicity, speed, low cost and environmental friendliness. [ABSTRACT FROM AUTHOR]

Aliphatic aldehydes are a class of organic compounds containing aldehyde groups, which are widespread, and closely related to people's daily life and health. In this work, a series of terpenes based hydrophobic deep eutectic solvents were designed and synthesized using hexafluoroisopropanol as hydrogen bond donor and menthol/thymol as hydrogen bond acceptor. Then they are used as extraction solvent in dispersive liquid-liquid microextraction for extracting and determining seven aliphatic aldehydes from drinking water and alcoholic beverage combined with high performance liquid chromatography-ultraviolet. Due to the fact that these hydrophobic deep eutectic solvents are liquid at the room temperature, a density greater than that of water, a lower viscosity (≤26.10 mPa s, 25 °C), after extraction and centrifugation, the microvolume DES-rich phase in the bottom is convenient for collection and direct analysis without further dissolution or dilution with organic solvents. Some factors affecting the extraction recovery were optimized by one-variable-at-a-time and response surface methodology. Under the optimal conditions, the enrichment factors for the seven aliphatic aldehydes were 48–56. The method had good performance: linear ranges of 1.0–200, 0.5–200, 0.2–200, 0.4–400, 1.0–400, 0.4–400 and 0.4–400 μg L−1 for seven aliphatic aldehydes (r 2 ≥ 0.9949), limits of detection of 0.1–0.5 μg L−1, intra-day and inter-day precisions <4.9%. The recoveries of seven aliphatic aldehydes ranged from 76.0 to 119.0%. The proposed dispersive liquid-liquid microextraction method is simple, rapid, highly efficient, and green, which effectively reduces the amount of toxic chemical reagents used and their impact on the environment. Rapid and efficient detection of aliphatic aldehydes helps ensure a healthy diet and has great application prospects in food safety analysis. [Display omitted] • Terpenes based HDESs with low viscosity and high density were designed and prepared. • A terpenes HDESs based DLLME was established for enrichment of aliphatic aldehydes. • The DES-rich phase in the bottom is easy to be collected and directly analyzed by HPLC. • The method is simple, rapid, effective and green for detecting aliphatic aldehydes. • The green profile of the method was assessed by AES and AGREE. [ABSTRACT FROM AUTHOR]

• One-step derivatization and TC-VA-LLME-SFDES method was developed. • Hydrophobic DESs were used as both reducing agent and extraction solvent. • Only 2 min was needed for derivatization and extraction process. • The method was applied for analysis of total Fe in water and food samples. • The method opened up the application of solid DESs in LLME technique. In our work, hydrophobic thymol-based deep eutectic solvents (DESs) with strong reducibility, a lower density than water, and a slightly higher melting point than room temperature were synthesized. Based on these solid DESs, one-step derivatization and temperature-controlled vortex-assisted liquid-liquid microextraction based on the solidification of a floating DES (TC-VA-LLME-SFDES) via UV–Vis spectrophotometry for the rapid determination of total iron was developed. The derivatization and TC-VA-LLME were carried out simultaneously by the addition of DES as both the reducing agent and extraction solvent. After optimization, the calibration curve (5–250 μg L−1, R2 = 0.9982), limit of detection (1.5 μg L−1), limit of quantitation (5.0 μg L−1), precision (≤4.0%) and enrichment factor (92) was obtained. This method was applied for the determination of total iron in water and food samples with satisfactory recoveries (85.4–106.2%). One-step derivatization and TC-VA-LLME only required 2 min. Furthermore, this method opened up the application of solid DESs in liquid–liquid microextraction. [ABSTRACT FROM AUTHOR]

• Novel AA-LLME based on solidification of floating DES method was developed. • DESs with low viscosity, density and melting point near room temperature were used. • Central composite design was used for the method optimization. • This method is simple, low cost, centrifugal-free, and environment friendly. For this work, a novel air-assisted liquid-liquid microextraction based on solidification of floating deep eutectic solvent (AA-LLME-SFDES), coupled with a high performance liquid chromatography (HPLC) method was developed for the detection of benzophenone and salicylate ultraviolet filters in water samples. Three types of fatty acid-based hydrophobic deep eutectic solvents (DESs) with low viscosity, low-density, and melting point close to room temperature were prepared and employed as extraction solvents. This air-assisted liquid-liquid microextraction was carried out in a glass centrifuge tube. Subsequently, the glass tube was introduced into ice-water bath and held for 3 min, during which the upper DES phase was solidified. The water phase was easily extracted using a syringe equipped with a long needle, and later, the glass tube was removed from ice-water bath. The solidified DES phase was immediately melted at room temperature and used for HPLC analysis. The response surface methodology was employed to optimize some influencing parameters such as the volume of the extraction solvent, the pH value of sample solution, the number of extraction cycles, and the addition of salt. A quadratic model, namely a central composite design, was used to replace the conventional single factor analysis. It was found that under optimal conditions, the limits of determination and quantification were 0.045–0.54 µg L−1 and 0.15–2.0 µg L−1, respectively. The relative standard deviations for inter-day (n = 5) and intra-day (n = 5) precision were ≤ 4.2%, whereas the enrichment factors for the ultraviolet filters were obtained from 41 to 50. Furthermore, this novel method was successfully employed for the detection of benzophenone and salicylate ultraviolet filters from real water samples. The recoveries ranged from 87.5% to 105.8%, whereas the RSDs were lower than 3.6%. [ABSTRACT FROM AUTHOR]