Search

Free positioning wireless charging for consumer electronics allows the devices to be charged at arbitrary positions and angles to improve user experience. However, a user-initiated sudden movement of the device during charging can cause hazards due to the abrupt variation of the coupling coefficient. To solve this issue, the coupling coefficient variation at different positions should be mitigated, which is also good for the design and high-efficiency operation of power electronics converters. This article proposes a design methodology to employ antiparallel windings to smooth the coupling coefficient variation over different positions by reducing the coupling coefficient at central positions and enhancing it at boundary positions. Two optimization methods are proposed: turn-by-turn optimization and winding-by-winding optimization. A design flow is offered. The hexagonal coil is compared with the square coil and proved to achieve better performance than the latter. An experimental prototype is implemented to validate the effectiveness of the proposed design methodology. [ABSTRACT FROM AUTHOR]

The isolated feature between primary and secondary sides in wireless power transfer requires dual-side communication, phase synchronization, and two controllers on both sides. The phase difference between dual-side ac voltages can be changed for output regulation or bidirectional power flow. Zero crossing detection of the secondary ac voltage or current is normally conducted for frequency locking and phase synchronization. However, it is inaccurate at light-load conditions for high-power applications due to a large sensing scale and much noise; also, it can generate undesired results with discontinuous or distorted waveforms having more than two zero crossing points in one cycle. To solve these issues, this letter proposes a dual-side phase-shift implementation method using driving windings to regulate the dual-side phase difference conducted only on the primary side. By controlling the phase difference between the primary-side power and driving windings, the phase difference between the dual-side power windings can be regulated. In this way, the dual-side regulation is independent from power transfer to get rid of the issues of the conventional phase synchronization method, and bidirectional power flow can be more easily realized. [ABSTRACT FROM AUTHOR]

To increase the power density of a wireless power transfer (WPT) system, the coupling of coils can be strong. However, in a strongly coupled series–series WPT system with a diode rectifier, currents can be distorted and discontinuous, and first harmonic approximation is no longer valid. The inverter is likely to work in hard switching, leading to extra noise, decreased efficiency, and a potential hazard for a safe operation. Through time-domain analysis, this article reveals that with a dual-side 90° phase shift, the hard switching of the inverter can be avoided, the power level can be enhanced, and the discontinuous conduction mode can be avoided to eliminate noises. The factors impacting the soft switching operations of the inverter and the rectifier are analyzed. To achieve 90° dual-side phase shift, the conventional approach of using the receiver voltage/current, which can be distorted and discontinuous in strongly coupled WPT systems, for phase synchronization is no longer suitable. A new set of coils, namely driving coils, is used for phase synchronization so that dual-side phase shift can be implemented independent from power transfer. Experimental results have validated the effectiveness of the analysis. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]