Search

This study investigates the effects of incorporating MgO into magnesium–calcium (Mg-Ca) alloy composites and subjecting them to the equal channel angular pressing (ECAP) process on the resulting mechanical and corrosive properties, as well as biocompatibility. Initially, the incorporation of MgO into the Mg-Ca alloy composites did not yield significant improvements in grain refinement, tensile strength, or corrosion rate reduction, despite exhibiting improved biocompatibility. However, upon subjecting the Mg-Ca-MgO alloy composites to the ECAP process, noteworthy outcomes were observed. The ECAP process resulted in substantial grain refinement, leading to significant improvements in tensile strength. Furthermore, a marked decrease in corrosion rate was observed, indicating enhanced corrosion resistance. Additionally, the biocompatibility of the Mg-Ca-MgO alloy composites improved after undergoing the ECAP process. These findings highlight the synergistic effect of incorporating MgO and employing the ECAP process, providing valuable insights into the development of advanced magnesium-based materials with superior mechanical properties, reduced corrosion rates, and improved biocompatibility. [ABSTRACT FROM AUTHOR]

The automobile industry uses magnesium for load-bearing components due to its low density, durability, and ductility. This study investigated a nanocomposite containing Nb2O5 (3 and 6 wt%) nanoparticles as reinforcement with AZ31 magnesium alloy made by stir casting. A severe plastic deformation was conducted on the cast samples via equal-channel angular pressing (ECAP) after homogenization at 410 °C for 24 h and aging at 200 °C for 10 h. The microstructural distributions and mechanical properties of the magnesium metal matrix composites (MMCs) reinforced with Nb2O5 nanoparticles were investigated via ECAP. With the increase in the number of ECAP passes, the grain sizes became uniform, and the size of secondary phases reduced in the pure Nb2O5/AZ31 MMC. The grain size decreased remarkably after the ECAP process from 31.95 µm to 18.41µm due to the dynamic recrystallization during plastic deformation. The mechanical properties of hardness, ultimate tensile strength, and elongation effectively improved after each ECAP pass. The maximum values achieved for the Nb2O5/AZ31 composite subjected to ECAP were 64.12 ± 12 HV, 151.2 MPa, and 52.71%. [ABSTRACT FROM AUTHOR]

In this study, the AZ31 magnesium alloy was reinforced with tungsten disulfide (WS2) nanotubes to fabricate the nanocomposite using the stir casting method. The microstructural analysis, mechanical and wear behaviors were investigated with the effect of WS2 on the AZ31 alloy. Scanning electron microscopy (SEM) was used to conduct the microstructural analysis. The microstructures are revealed to incorporate the aluminum content with the WS2 nanotube, disclose the presence of the secondary phase, which was increased compared with the AZ31 alloy and was detected by energy dispersive spectroscopy (EDS). The mechanical properties of hardness and yield strength (YS) were significantly improved with the addition of WS2 nanotubes. This is mainly due to the strengthening mechanisms of Orowan, the coefficient of thermal expansion (CTE) mismatch and the load transfer mechanism. The theoretical YS was calculated and compared with the experimental results. However, the ultimate tensile strength (UTS) and the fracture strain were decreased with the addition of reinforcement which might be owing to the clustering of nanotubes. Finally, the wear behavior of the wear weight loss and depth of cut was investigated. This test revealed that the addition of WS2 nanotubes reduced the weight loss and depth of the material cutting that was mainly due to the presence of hard WS2 nanotubes. [ABSTRACT FROM AUTHOR]

AZ61 magnesium alloy metal matrix composites (MMCs) with different weight percentages (0, 1 and 2) of micro-silicon carbide particles (SiCp) were fabricated using stir casting method. Effects of SiCp on the microstructural distributions, mechanical and fatigue properties, and fracture surfaces have been investigated. The microstructural observations of as-cast MMCs unveil the existence of primary α-Mg phase and the presence of large amount of β-Mg17Al12 secondary phase at grain boundary. The specimens are subjected to homogenization heat treatment at 410 °C for 24 h; the β-Mg17Al12 phases are significantly dissolved in the matrix grain boundaries which enhance the ductility and decrease the hardness compared with the as-cast materials. The addition of SiCp reinforcement led to improved yield strength (YS) and ultimate tensile strength (UTS) of AZ61/SiCp composite compared to the unreinforced alloy. The maximum values of YS and UTS have been attained at AZ61/1wt%SiCp composites. The enhancement of YS and UTS was due to the presence of a uniformly distributed reinforced SiCp, which depends on grain refinement of the matrix and strong interfacial bonding between the matrix and reinforcement. In the case of fatigue test results, the addition of SiCp reduced the fatigue life and strength of AZ61 alloy composite. However, addition of 1wt%SiCp showed good mechanical and fatigue properties compared to pure AZ61 magnesium alloy and AZ61/2wt%SiCp composite. Furthermore, the effects of addition of SiCp on the mechanical and fatigue properties of the composite were confirmed by using the scanning electron microscope observation of fracture surfaces. [ABSTRACT FROM AUTHOR]

In this study, AZ61 alloy processed by equal channel angular pressing (ECAP) method, is presented. This research seeks to find out the relationship that exists between the microstructure of the AZ61-magnesium alloy doped with SiC and Ni and processed by ECAP in terms of hydrogen storage properties. The results indicate that grain size reduces nearly 10 times after 4 passes of ECAP. Homogeneous distribution of the SiC in the metal matrix composite (MMC) and dynamic recrystallization are also observed. There is a gradual reduction in the grain size when the number of ECAP passes are increased. This microstructural refinement induced by ECAP improves the storage capacity and reaction kinetics of the alloy. Besides, the addition of Ni catalyst achieves faster absorption and desorption kinetics. However, it does not change its capacity. Ni reacts with Mg to form an intermetallic, which is hydrogen-absorbing, which in turn, catalyzes the reaction. Apart from introducing defects, the ECAP process also produces Mg/Al intermetallic, which acts catalytically. It is shown that SiC-doped AZ61-magnesium alloy can absorb and desorb 6.8 wt% H 2 at 648 K and 50 atm. • AZ61 with SiC and Ni additives prepared by gravity stir casting method. • Dispersion characteristics of the particles influences the rate limiting factors. • AZ61-1 wt%SiC achieves a hydrogen capacity of 6.8 wt%. • Performance declines to 6.5 wt% when Ni catalyst is added. • Combining SiC and Ni shows improved kinetics. [ABSTRACT FROM AUTHOR]

In this research, magnesium alloy AZ31 reinforced with CNTs (0 wt.%, 0.1 wt.%, 0.5 wt.%, 1 wt.%) was produced by a stir casting method followed by aged heat treatment. Composites were investigated using x-ray diffraction and scanning electron microscope techniques. The microstructure of the CNTs/AZ31 has been qualitatively and quantitatively evaluated. The results show that stir casting is a suitable method for uniformly distributing CNTs and maintaining the integrated structure. The concentration of CNTs and aged heat treatment affects the crystallite size, crystallinity degree, precipitates and phase composition of the CNT-reinforced AZ31 alloy. An increase in the concentration of CNTs results in a decrease in the degree of crystallinity and dissolution of the secondary phase. In 0.1 wt.% CNTs, the crystallite size decreases and then increases. The aged heat treatment affects the composition of the phase and creates a new secondary phase to refine the microstructure and grain size. The compressive strength is linearly related to the concentration of CNTs. Bramfitt disregistry and precipitation strengthening play an important role in qualitatively and quantitatively refining and altering the microstructure of CNTs/AZ31. [ABSTRACT FROM AUTHOR]

In this paper, solution and ageing heat treatment processes were used to improve microplastic deformation behaviors of as-cast SiCp/AZ61 magnesium metal matrix composites (Mg MMCs) fabricated by stir casting method. Higher percentages of SiC particle reinforcements showed higher microhardness values. Ageing heat treatment process was seen significant on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC which induced lower microhardness value. At the 12 h ageing of 2 wt% SiCp/AZ61 Mg MMC the formations of particle free regions and discontinuous secondary phases were observed. For a higher ageing time, the secondary phases distribution became continuous and laminar structure. The addition of 5 wt% SiC particles resulted in the formation of Mg 2 Si phase throughout the whole heat treatment processes. The addition of SiC particles reinforcements increased the phase heterogeneity during ageing heat treatment processes. XRD patterns revealed the presence of nanocrystalline MgSiO 3 phase on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC. Using reference intensity ration (RIR) method a 51.6% of MgSiO 3 phase was determined which can cause the formation of microplastic deformation behavior. And also, the maximum average crystallite size, compressive microstrain and microcrack-free phase boundaries were observed on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC. [ABSTRACT FROM AUTHOR]

The process engineering of Mg alloys is nevertheless compromised due to their relatively poor mechanical properties. To address some of these difficulties, metal-matrix composites (MMCs) of Mg-alloys have been investigated for sometime. In the present work, small amounts (up to 1 wt%) of WS 2 nanotubes are mixed with Mg-alloy (AZ31) using melt-stirring process above 700 °C. The new MMC nanocomposites exhibit much superior mechanical properties vis a vis the pristine alloy. Metallographic investigation demonstrates that the average grain size has been reduced in inverse proportion to the added amounts of nanotubes up to 1 wt%. Physical considerations suggest that the main mechanism responsible for the reinforcement effect lies in the mismatch between the thermal expansion coefficients of the metal and the nanotubes. This mismatch induced large density of dislocations in the grain boundaries in the vicinity of the nanotube-matrix interface, which obstruct the crack propagation. [ABSTRACT FROM AUTHOR]

The effect of equal channel angular extrusion (ECAE) on the mechanical behavior of AM60/Al2O3p magnesium metal–matrix nanocomposites was investigated. ECAE is a useful technique to produce bulk nanostructured materials through severe plastic deformation. The present magnesium metal–matrix composites (Mg MMCs) with 1 wt% nanosized Al2O3 particles for ECAE were fabricated using stir-casting method. The significantly enhanced mechanical behavior of AM60/Al2O3p magnesium metal–matrix nanocomposites at room temperature, for instance, yield strength (YS), ultimate tensile strength (UTS), and ductility, can be obtained after ECAE process. The AM60/Al2O3p MMC after 4 passes of ECAE exhibited greater YS, UTS, and ductility (+135%, +107%, and +245% increase, respectively) than those of as-cast AM60. Experimental results show that the AM60/1wt %Al2O3p MMC after 4 passes of ECAE exhibits the superior mechanical behavior. [ABSTRACT FROM AUTHOR]

Abstract: The effects of Mn substitution for Mg on the microstructure, mechanical properties, and corrosion behavior of Mg69−xZn27Ca4Mnx (x=0, 0.5 and 1at.%) alloys were investigated using X-ray diffraction, compressive tests, electrochemical treatments, and immersion tests, respectively. Microstructural observations showed that the Mg69Zn27Ca4 alloy was mainly amorphous. The addition of Mn decreases the glass-forming ability, which results in a decreased strength from 545MPa to 364MPa. However, this strength is still suitable for implant application. Polarization and immersion tests in the simulated body fluid at 37°C revealed that the Mn-doped Mg–Zn–Ca alloys have significantly higher corrosion resistance than traditional ZK60 and pure Mg alloys. Cytotoxicity test showed that cell viabilities of osteoblasts cultured with Mn-doped Mg–Zn–Ca alloys extracts were higher than that of pure Mg. Mg68.5Zn27Ca4Mn0.5 exhibits the highest bio-corrosion resistance, biocompatibility and has desirable mechanical properties, which could suggest to be used as biomedical materials in the future. [Copyright &y& Elsevier]

This study involves the investigation of the mechanical properties of the extruded tube products with reinforced silicon carbide particulates (SiCp). Finite element analyses are firstly conducted to analyze the plastic flow of the magnesium alloy AZ61 within the die and to investigate the effects of initial billet temperatures on the extrusion loads and final product temperatures. AZ61/SiCp composite ingots reinforced with different weight fractions of SiCp are fabricated by a melt stirring technique. A specially designed die set is used in the extrusion experiments to obtain tubes with uniform thickness distribution in the circumferential direction. The extruded tubes are also heat treated to obtain even better mechanical properties. Finally, tensile tests, Vickers microhardness, tests and microstructure observation are performed on the billets and extruded tubes of AZ61 monolithic alloys and AZ61/SiCp composites. A much smaller grain size and higher tensile strength and hardness are achieved for the extruded AZ61/SiCp composite tubes. [ABSTRACT FROM AUTHOR]

Gravitational melt-stir casting produced hybrid nano-reinforcements (β-SiCp) and micro-reinforcements (Bi and Sb) of AZ91 composites. SiCp-diffused discontinuous β-Mg17Al12 precipitation with a vital factor of SiC was exhibited at the grain boundary region, formulated Mg3Si throughout the composite and changed the present Mg0.97Zn0.03 phases. The creation of Mg2Si (cubic) and SiC (rhombohedral axes) enhanced the microhardness by 18.60% in a 0.5 wt.% SiCp/AZ91 matrix. The microhardness of 1 wt.% SiCp/AZ91 was slightly reduced after Mg0.97Zn0.03 (hexagonal) reduction. The best ultimate tensile value obtained was about 169.33 MPa (increased by 40.10%) in a 0.5 wt.% SiCp/AZ91 matrix. Microelements Bi and Sb developed Mg3Bi2, Mg3Sb2 and monoclinic C60 phases. The best peak yield strength of 82.75 MPa (increased by 19.85%) was obtained with the addition of 0.5 wt.% SiCp/1 wt.% Bi/0.4 wt.% Sb. The mismatch of the coefficient of thermal expansion of segregated particles and the AZ91 matrix, the shear transfer effect and the Orowan effect, combined with the quantitative value of phase existence, improved the compressive strengths of the composites with 0.5 wt.% β-SiCp, 1 wt.% β-SiCp and 0.5 wt.% SiCp/1 wt.% Bi/0.4 wt.% Sb by 2.68%, 6.23% and 8.38%, respectively. Notably, the Charpy impact strengths of 0.5 wt.% and 1 wt.% β-SiCp-added AZ91 composites were enhanced by 236% (2.89 J) and 192% (2.35 J), respectively. The addition of Bi and Sb with SiCp resulted in the formation of a massive phase of brittle Al6Mn. Al–Mn-based phases (developed huge voids and cavities) remarkably reduced impact values by 80% (0.98 J). The discussion covers the quantitative analyses of X-ray diffraction, optical microscopy and scanning electron microscopy results and fracture surfaces. [ABSTRACT FROM AUTHOR]

In this work, AZ91 magnesium alloy reinforced with a low fraction (0–1) wt.% tungsten disulfide(WS 2) microparticles have been fabricated using stir casting method. Effects of WS 2 microparticles on mechanical properties, microstructure, and their correlation have been analyzed. The microstructure of composites has been investigated by scanning electron microscope (SEM) equipped with energy dispersive spectroscopy (EDS) and X-ray diffractometer. Results indicate that density, hardness, ultimate tensile strength (UTS), and tensile ductility have a direct relation with reinforcement (WS 2) contents and has optimal value for 0.6 wt% WS 2 /AZ91 composites then slightly decrease afterward. The UTS and hardness of 0.6 wt%WS 2 /AZ91 were increased by 23.23% and 10.65% respectively with respect to monolithic AZ91. The ultimate compressive strength(UCS) is directly related with WS 2 concentration and 10.07% enhancement in UCS for 1 wt%WS 2 /AZ91 composites have been noted. The trend is interlinked with density and hardness of composites. SEM images depict, WS 2 micro-particles suppress β-Mg 17 Al 12 precipitates, refine the microstructure and enhance the grain size resulting in an increase in mechanical properties. The improvement in microstructure and mechanical properties is attributed to the dispersion of WS 2 particles which hinder the grain growth. The increase in porosity has causes the decrease in mechanical behavior of 1 wt%WS 2 /AZ91. Twin boundary fracture has been found major fracture phenomenon in fractured WS 2 /AZ91 surfaces. • WS 2 /AZ91 metal matrix composites have been manufacture by stir casting method. • Density and porosity of WS 2 /AZ91 composites has been assessed. • Mechanical behavior under compression and tension has been analyzed. • Effect of WS 2 on microstructure has been investigated. • Fracture behavior of composites has been studied. [ABSTRACT FROM AUTHOR]

The tribological behavior of AZ31 Mg alloy reinforced with multiwall carbon nanotubes (MWCNTs) was studied through experiments on a ring-on-block wear testing apparatus against 45C steel. The composites were successfully fabricated using stir-casting processing with different percentages of MWCNTs and then age hardened for 10 h. The effect of the various concentrations of MWCNTs on the microstructures, tribological properties, and wear mechanisms of the composites were systematically examined by scanning electron microscopy (SEM). With increasing percentage content of MWCNTs, the wear rate and the coefficient of friction decreased, which is attributed to the microhardness and self-lubricating properties of the MWCNTs. The microstructure characterization results established different mechanisms—specifically, abrasion, oxidation, and delamination—and very small plastic deformation. • Magnesium alloy AZ31 reinforced with multiwalled carbon nanotubes was fabricated using stir casting method. • Samples were homogenized for 24 h at 400C0 and then aged for 10 h at 200C0 temperature. • Wear tests for as-cast and aged composites were performed using Ring on Block wear apparatus under dry and wet conditions and mass wear loss and coefficient of friction was determined. • Worn surfaces were analyzed using scanning electron microscope for wear mechanism analysis. [ABSTRACT FROM AUTHOR]