Search

Abstract Helmholtz resonators (HRs) are widely used to damp acoustic oscillations, including in the combustors of aero-engines and power gas turbines where they damp thermoacoustic oscillations. The geometries of such combustors are often annular in shape, which means that low frequency acoustic modes exhibit both longitudinal and circumferential modeshapes, the latter across different circumferential wave numbers. For linear acoustic disturbances downstream of the flame, the presence of HRs leads to modal coupling and mode shape shifts, which makes design and placement of multiple HRs very complicated. A procedure which ensures that the design and placement of the HRs can be optimised for good acoustic damping performance would be very valuable, and such a procedure is presented in this work. A simplified linear, low-dimensional model for the acoustic behaviour in a hot annular duct sustaining a mean flow is extended to account for the attachment of multiple HRs. The HRs are assumed to sustain a cooling mean bias flow through them, towards the combustor, such that they can be modelled using linear, lumped element Rayleigh conductivity models. An optimisation method based on the gradient derived from adjoint sensitivity analysis is then applied to the low order network acoustic modelling framework for hot annular ducts incorporating HR models, for the first time. It is used to optimise over multiple HR geometry and placement parameters, to obtain optimum acoustic damping over all acoustic modes in a given frequency range. These optimisation procedures are validated via multi-dimensional parameter sweep results. Thus a novel and efficient tool for HR optimisation for thin annular ducts is presented. [ABSTRACT FROM AUTHOR]

The sound generated or absorbed by short circular holes with a mean flow passing through them is relevant in many practical applications. Analytical models for their acoustic response often ignore the fact that such holes open to a confined or finite space either side, or account for this effect simply by adding an end mass inertial correction. The vortex–sound interaction within a short hole has been recently shown to strongly affect the acoustic response at low frequencies (D. Yang, A.S. Morgans, J. Sound Vib. 384 (2016) 294–311 [ 19] ). The present study considers a semi-analytical model based on Green's function method to investigate how the expansion ratios either side of a short hole affect the vortex–sound interaction within it. After accounting for expansions to confined spaces using a cylinder Green's function method, the model is substantially simplified by applying a half-space Green's function for expansions to large spaces. The effect of both the up- and downstream expansion ratios on the acoustics of the hole is investigated. These hole models are then incorporated into a Helmholtz resonator model, allowing a systematic investigation into the effect of neck-to-cavity expansion ratio and neck length. Both of these are found to affect the resonator damping. [ABSTRACT FROM AUTHOR]

The acoustic response of a circular hole with mean flow passing through it is highly relevant to Helmholtz resonators, fuel injectors, perforated plates, screens, liners and many other engineering applications. A widely used analytical model [M.S. Howe. “Onthe theory of unsteady high Reynolds number flow through a circular aperture”, Proc. of the Royal Soc. A. 366, 1725 (1979), 205‐223] which assumes an infinitesimally short hole was recently shown to be insufficient for predicting the impedance of holes with a finite length. In the present work, an analytical model based on Green׳s function method is developed to take the hole length into consideration for “short” holes. The importance of capturing the modified vortex noise accurately is shown. The vortices shed at the hole inlet edge are convected to the hole outlet and further downstream to form a vortex sheet. This couples with the acoustic waves and this coupling has the potential to generate as well as absorb acoustic energy in the low frequency region. The impedance predicted by this model shows the importance of capturing the path of the shed vortex. When the vortex path is captured accurately, the impedance predictions agree well with previous experimental and CFD results, for example predicting the potential for generation of acoustic energy at higher frequencies. For “long” holes, a simplified model which combines Howe׳s model with plane acoustic waves within the hole is developed. It is shown that the most important effect in this case is the acoustic non-compactness of the hole. [ABSTRACT FROM AUTHOR]

Helmholtz resonators with sound absorption materials filling the neck may have an improved sound absorption capacity. In this work, parallel perforated ceramics with different perforation diameters were installed into the neck of a Helmholtz resonator to improve its acoustic impedance to simultaneously achieve a better acoustic absorption coefficient and a wider absorption bandwidth. An experimental system was built to investigate the effect of the perforation diameters on the sound absorption performance of the resonator. It is found that nonlinear effects near the resonance frequency affect the resonator׳s neck mouth impedance and further its sound absorption performance significantly. For frequency range 50–500 Hz, a model of the neck mouth impedance is developed based on a revised Forchheimer relationship. The experimental results are in good agreement with the theoretical model. [ABSTRACT FROM AUTHOR]