Search

A magnetically shielded Hall thruster (MSHT) has a significantly longer service life than a conventional unshielded Hall thruster (USHT) as it shifts the magnetic field of maximum strength from the channel interior to the exterior. In this study, it was experimentally determined that the influence of the radial position of an externally mounted hollow cathode on the performance of an MSHT is quite different from that of a USHT. The measured plasma parameters demonstrate that in addition to the coupling voltage loss and plume divergence loss, the electron cross-field transport loss (not considered previously and introduced by the outward shifting of the magnetic field) is also important to explaining the performance variation in the MSHT. This study refines the coupling theory between the cathode and Hall thruster and provides a valuable reference for determining the radial position of an externally mounted hollow cathode in an MSHT. [ABSTRACT FROM AUTHOR]

In an ATON-type Hall effect thruster, a ring-shaped anode and a cusped magnetic field intersect the match between the anode shape and the field topology thus must be clarified to optimize the electron transport to the anode and consequently the design of a high-efficiency thruster. By changing the match pattern with both the change in the length of the anode ring and the axial displacement of the cusp magnetic field, this study experimentally investigated the influence of the match pattern on the discharge characteristics of an ATON-type thruster—P100—under the condition of a moderate discharge voltage. The experimental results show that there is a match pattern that always optimizes the performance of the P100 thruster. At the rated operation parameters (300 V of discharge voltage and 5 mg/s of propellant mass flow rate) and the rated magnetic field strength, the observed improvements on thrust (∼79 mN to ∼85 mN) and anode efficiency (∼46% to ∼55%) are significant. Through further theoretical analysis, this study revealed that the change in the characteristics of electron momentum and energy transfer in the near-anode region, induced by the change of the match pattern, is the basic reason. The findings of this work are instructive for both understanding the electron motion in a cusp magnetic field and guiding the design of the anode ring intersecting with a cusp magnetic field in an ATON-type Hall effect thruster. [ABSTRACT FROM AUTHOR]

This study proposes a newly designed ignition circuit that does not change the ignition starting parameters of a Hall thruster, reduces the critical ignition voltage, and improves ignition reliability. The complexity and weight of the Hall thruster power supply system are reduced by multiplexing the ignition and discharge power supplies. Under the condition that the design parameters are satisfied, that is, R 3 + R E C 2 is much larger than RCC1, the residual energy in the circuit after the cathode breakdown can be fed into the thruster discharge channel to improve the ignition energy supply. The experimental results show that when the anode voltage is 98 V, only nine of the 100 ignition tests are successful using the traditional ignition circuit, whereas the number of successes using the newly designed ignition circuit is as high as 99, which provides a simple solution method for improving the ignition reliability. [ABSTRACT FROM AUTHOR]

Increasing the specific impulse has become one of the main trends in the development of Hall thrusters and may be achieved by increasing the proportion of multiply charged ions in the plume. In this study, the multiple ionization characteristics of Hall thrusters with large height–radius ratios and their effects on the specific impulse and other performance parameters were examined via numerical simulations. The simulation results show that the proportion of multiply charged ions in a Hall thruster with a large height–radius ratio increases by 7.8 percentage points, compared with that of the traditional Hall thruster, and the multiply charged ions can obtain a higher average jet velocity under an accelerating voltage, thereby improving the specific impulse and thrust of the thruster. Further analyses show that a structure with a large height–radius ratio reduces the cooling effect of the channel wall on the electrons, and the increase in electron temperature effectively promotes the occurrence of the multiple ionization process. In addition, the smaller wall area and the larger magnetic field intensity in the near-wall region inhibit the electron near-wall conduction and prevent the potential negative effect of the increase in electron current caused by multiply charged ionization, which ensures a high level of efficiency. It was proved that multiple ionizations contribute positively to the specific impulse and efficiency of Hall thrusters with a large height–radius ratio. This serves as a reference for the high specific impulse design of Hall thrusters with large height–radius ratios and provides a new optimization perspective for improving the specific impulse of Hall thrusters. [ABSTRACT FROM AUTHOR]

During a long-term discharge of a Hall thruster, local overheating on the anode surface occurs and its location shifts randomly. The asymmetrical supply of anode potential is thought to be the cause. To investigate their relationship, a bias voltage is applied on one piece of a quartered anode to realize the asymmetrical supply of anode potential. Variations of both the current and temperature of each anode piece are measured and analyzed. The results indicate that the disruption of the anode potential symmetrical supply does not affect the total anode current; however, it enhances the current oscillation. As the bias voltage increases, the current concentrates gradually on the high-potential part of the anode, accompanied by an increase in the local temperature. Changes in the Ez × Br drift direction, magnetic field strength, discharge voltage, and anode flow rate do not affect the above-mentioned laws. Preliminary analysis shows that the formation of a local electric field near the anode and the generation of an extra Eθ × Br drift are the main causes, which can affect the movement of electrons in the near-anode region greatly. [ABSTRACT FROM AUTHOR]

The strength and shape of the magnetic field are the core factors in the design of the Hall thruster. However, Hall current can affect the distribution of static magnetic field. In this paper, the Particle-In-Cell (PIC) method is used to obtain the distribution of Hall current in the discharge channel. The Hall current is separated into a direct and an alternating part to calculate the induced magnetic field using Finite Element Method Magnetics (FEMM). The results show that the direct Hall current decreases the magnetic field strength in the acceleration region and also changes the shape of the magnetic field. The maximum reduction in radial magnetic field strength in the exit plane is 10.8 G for an anode flow rate of 15 mg/s and the maximum angle change of the magnetic field line is close to 3° in the acceleration region. The alternating Hall current induces an oscillating magnetic field in the whole discharge channel. The actual magnetic deformation is shown to contain these two parts. [ABSTRACT FROM AUTHOR]