Search

In this study, AZ61 alloy processed by equal channel angular pressing (ECAP) method, is presented. This research seeks to find out the relationship that exists between the microstructure of the AZ61-magnesium alloy doped with SiC and Ni and processed by ECAP in terms of hydrogen storage properties. The results indicate that grain size reduces nearly 10 times after 4 passes of ECAP. Homogeneous distribution of the SiC in the metal matrix composite (MMC) and dynamic recrystallization are also observed. There is a gradual reduction in the grain size when the number of ECAP passes are increased. This microstructural refinement induced by ECAP improves the storage capacity and reaction kinetics of the alloy. Besides, the addition of Ni catalyst achieves faster absorption and desorption kinetics. However, it does not change its capacity. Ni reacts with Mg to form an intermetallic, which is hydrogen-absorbing, which in turn, catalyzes the reaction. Apart from introducing defects, the ECAP process also produces Mg/Al intermetallic, which acts catalytically. It is shown that SiC-doped AZ61-magnesium alloy can absorb and desorb 6.8 wt% H 2 at 648 K and 50 atm. • AZ61 with SiC and Ni additives prepared by gravity stir casting method. • Dispersion characteristics of the particles influences the rate limiting factors. • AZ61-1 wt%SiC achieves a hydrogen capacity of 6.8 wt%. • Performance declines to 6.5 wt% when Ni catalyst is added. • Combining SiC and Ni shows improved kinetics. [ABSTRACT FROM AUTHOR]

In this paper, solution and ageing heat treatment processes were used to improve microplastic deformation behaviors of as-cast SiCp/AZ61 magnesium metal matrix composites (Mg MMCs) fabricated by stir casting method. Higher percentages of SiC particle reinforcements showed higher microhardness values. Ageing heat treatment process was seen significant on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC which induced lower microhardness value. At the 12 h ageing of 2 wt% SiCp/AZ61 Mg MMC the formations of particle free regions and discontinuous secondary phases were observed. For a higher ageing time, the secondary phases distribution became continuous and laminar structure. The addition of 5 wt% SiC particles resulted in the formation of Mg 2 Si phase throughout the whole heat treatment processes. The addition of SiC particles reinforcements increased the phase heterogeneity during ageing heat treatment processes. XRD patterns revealed the presence of nanocrystalline MgSiO 3 phase on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC. Using reference intensity ration (RIR) method a 51.6% of MgSiO 3 phase was determined which can cause the formation of microplastic deformation behavior. And also, the maximum average crystallite size, compressive microstrain and microcrack-free phase boundaries were observed on the 12 h aged 2 wt% SiCp/AZ61 Mg MMC. [ABSTRACT FROM AUTHOR]

The process engineering of Mg alloys is nevertheless compromised due to their relatively poor mechanical properties. To address some of these difficulties, metal-matrix composites (MMCs) of Mg-alloys have been investigated for sometime. In the present work, small amounts (up to 1 wt%) of WS 2 nanotubes are mixed with Mg-alloy (AZ31) using melt-stirring process above 700 °C. The new MMC nanocomposites exhibit much superior mechanical properties vis a vis the pristine alloy. Metallographic investigation demonstrates that the average grain size has been reduced in inverse proportion to the added amounts of nanotubes up to 1 wt%. Physical considerations suggest that the main mechanism responsible for the reinforcement effect lies in the mismatch between the thermal expansion coefficients of the metal and the nanotubes. This mismatch induced large density of dislocations in the grain boundaries in the vicinity of the nanotube-matrix interface, which obstruct the crack propagation. [ABSTRACT FROM AUTHOR]

Abstract: The effects of Mn substitution for Mg on the microstructure, mechanical properties, and corrosion behavior of Mg69−xZn27Ca4Mnx (x=0, 0.5 and 1at.%) alloys were investigated using X-ray diffraction, compressive tests, electrochemical treatments, and immersion tests, respectively. Microstructural observations showed that the Mg69Zn27Ca4 alloy was mainly amorphous. The addition of Mn decreases the glass-forming ability, which results in a decreased strength from 545MPa to 364MPa. However, this strength is still suitable for implant application. Polarization and immersion tests in the simulated body fluid at 37°C revealed that the Mn-doped Mg–Zn–Ca alloys have significantly higher corrosion resistance than traditional ZK60 and pure Mg alloys. Cytotoxicity test showed that cell viabilities of osteoblasts cultured with Mn-doped Mg–Zn–Ca alloys extracts were higher than that of pure Mg. Mg68.5Zn27Ca4Mn0.5 exhibits the highest bio-corrosion resistance, biocompatibility and has desirable mechanical properties, which could suggest to be used as biomedical materials in the future. [Copyright &y& Elsevier]

In this work, AZ91 magnesium alloy reinforced with a low fraction (0–1) wt.% tungsten disulfide(WS 2) microparticles have been fabricated using stir casting method. Effects of WS 2 microparticles on mechanical properties, microstructure, and their correlation have been analyzed. The microstructure of composites has been investigated by scanning electron microscope (SEM) equipped with energy dispersive spectroscopy (EDS) and X-ray diffractometer. Results indicate that density, hardness, ultimate tensile strength (UTS), and tensile ductility have a direct relation with reinforcement (WS 2) contents and has optimal value for 0.6 wt% WS 2 /AZ91 composites then slightly decrease afterward. The UTS and hardness of 0.6 wt%WS 2 /AZ91 were increased by 23.23% and 10.65% respectively with respect to monolithic AZ91. The ultimate compressive strength(UCS) is directly related with WS 2 concentration and 10.07% enhancement in UCS for 1 wt%WS 2 /AZ91 composites have been noted. The trend is interlinked with density and hardness of composites. SEM images depict, WS 2 micro-particles suppress β-Mg 17 Al 12 precipitates, refine the microstructure and enhance the grain size resulting in an increase in mechanical properties. The improvement in microstructure and mechanical properties is attributed to the dispersion of WS 2 particles which hinder the grain growth. The increase in porosity has causes the decrease in mechanical behavior of 1 wt%WS 2 /AZ91. Twin boundary fracture has been found major fracture phenomenon in fractured WS 2 /AZ91 surfaces. • WS 2 /AZ91 metal matrix composites have been manufacture by stir casting method. • Density and porosity of WS 2 /AZ91 composites has been assessed. • Mechanical behavior under compression and tension has been analyzed. • Effect of WS 2 on microstructure has been investigated. • Fracture behavior of composites has been studied. [ABSTRACT FROM AUTHOR]

The tribological behavior of AZ31 Mg alloy reinforced with multiwall carbon nanotubes (MWCNTs) was studied through experiments on a ring-on-block wear testing apparatus against 45C steel. The composites were successfully fabricated using stir-casting processing with different percentages of MWCNTs and then age hardened for 10 h. The effect of the various concentrations of MWCNTs on the microstructures, tribological properties, and wear mechanisms of the composites were systematically examined by scanning electron microscopy (SEM). With increasing percentage content of MWCNTs, the wear rate and the coefficient of friction decreased, which is attributed to the microhardness and self-lubricating properties of the MWCNTs. The microstructure characterization results established different mechanisms—specifically, abrasion, oxidation, and delamination—and very small plastic deformation. • Magnesium alloy AZ31 reinforced with multiwalled carbon nanotubes was fabricated using stir casting method. • Samples were homogenized for 24 h at 400C0 and then aged for 10 h at 200C0 temperature. • Wear tests for as-cast and aged composites were performed using Ring on Block wear apparatus under dry and wet conditions and mass wear loss and coefficient of friction was determined. • Worn surfaces were analyzed using scanning electron microscope for wear mechanism analysis. [ABSTRACT FROM AUTHOR]