Search

This paper introduces a novel isolated hybrid resonant converter with smooth transition between multiple operating modes. With the simple addition of a bidirectional ac switch, the highly efficient series resonant converter operating in the discontinuous conduction mode is combined with a phase-shifted full-bridge buck converter and a pulsewidth-modulated boost converter in order to provide high power conversion efficiency over a wide input-voltage operating range utilizing a simple topology and simple control techniques. First, the topology is introduced, and the converter's operating modes are discussed. Next, closed-loop input-voltage controllers are designed for the different operating modes, and a smooth transition technique is introduced using a two-carrier modulation scheme. Experimental results are provided to verify the proposed system using a 300-W prototype that achieved a 97.5% California Energy Commission weighted efficiency with a 30-V input including all auxiliary and control losses. [ABSTRACT FROM AUTHOR]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper presents a single-phase transformerless grid-connected photovoltaic converter based on two cascaded full bridges with different dc-link voltages. The converter can synthesize up to nine voltage levels with a single dc bus, since one of the full bridges is supplied by a flying capacitor. The multilevel output reduces harmonic distortion and electromagnetic interference. A suitable switching strategy is employed to regulate the flying-capacitor voltage, improve the efficiency (most devices switch at the grid frequency), and minimize the common-mode leakage current with the help of a novel dedicated circuit (transient circuit). Simulations and experiments confirm the feasibility and good performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

A family of dual-phase-combined resonant switched-capacitor (SC) converters with a similar structure is presented in this paper. Comparing with their conventional single-phase version, each of the proposed dual-phase converters is more than just a switched capacitor but also provides the service of two phases operated in the fully complementary manner. This design provides a more stable output voltage with low ripple and significantly reduces the quantity of switches. These converters therefore have the common features of smaller size, lower cost, and higher power density than the conventional multiphase SC converters. With the zero-current switching technique, the proposed converters also possess high-power conversion efficiency. The detailed analysis of the circuit operation and voltage ripples is presented. Experimental results are also provided to confirm the performance of the new family of converters. [ABSTRACT FROM AUTHOR]

This paper presents a multilevel inverter that has been conceptualized to reduce component count, particularly for a large number of output levels. It comprises floating input dc sources alternately connected in opposite polarities with one another through power switches. Each input dc level appears in the stepped load voltage either individually or in additive combinations with other input levels. This approach results in reduced number of power switches as compared to classical topologies. The working principle of the proposed topology is demonstrated with the help of a single-phase five-level inverter. The topology is investigated through simulations and validated experimentally on a laboratory prototype. An exhaustive comparison of the proposed topology is made against the classical cascaded H-bridge topology. [ABSTRACT FROM PUBLISHER]

In this paper, a model predictive control strategy is adapted to the cascaded H-bridge (CHB) multilevel rectifier. The proposed control scheme aims to keep the sinusoidal input current in phase with the supply voltage and to achieve independent voltage regulation of the H-bridge cells. To do so, the switches are directly manipulated without the need of a modulator. Furthermore, since all the possible switching combinations are taken into account, the controller exhibits favorable performance not only under nominal conditions but also under asymmetrical voltage potentials and unbalanced loads. Finally, a short horizon is employed in order to ensure robustness; this way, the required computational effort remains reasonable, making it possible to implement the algorithm in a real-time system. Experimental results obtained from a two-cell CHB rectifier are presented in order to demonstrate the performance of the proposed approach. [ABSTRACT FROM PUBLISHER]

Modular photovoltaic (PV) power conditioning systems (PCSs) require a high-efficiency dc-dc converter stage capable of regulation over a wide input voltage range for maximum power point tracking. In order to mitigate ground leakage currents and to be able to use a high-efficiency, nonisolated grid-tied inverter, it is also desirable for this microconverter to provide galvanic isolation between the PV module and the inverter. This paper presents a novel, isolated topology that is able to meet the high efficiency over a wide input voltage range requirement. This topology yields high efficiency through low circulating currents, zero-voltage switching (ZVS) and low-current switching of the primary side devices, ZCS of the output diodes, and direct power transfer to the load for the majority of switching cycle. This topology is also able to provide voltage regulation through basic fixed-frequency pulsewidth modulated (PWM) control. These features are able to be achieved with the simple addition of a secondary-side bidirectional ac switch to the isolated series resonant converter. Detailed analysis of the operation of this converter is discussed along with a detailed design procedure. Experimental results of a 300-W prototype are given. The prototype reached a peak power stage efficiency of 98.3% and a California Energy Commission (CEC) weighted power stage efficiency of 98.0% at the nominal input voltage. [ABSTRACT FROM AUTHOR]

A European efficiency enhancement strategy for the grid-tied inverters with common dc bus and ac bus in parallel operation is proposed in this paper. Based on the inherent relationship between the dc bus voltage and the grid-feeding power, two dc bus voltage regulators with different output limits are employed in each grid-tied inverter. The operation of the dc bus voltage regulators depends on the grid-feeding power level. Therefore, the grid-tied inverter has priority up to the maximum efficiency operation point, and then, to operate at full load mode with the increase of the grid-feeding power. As a result, the European efficiency of the grid-tied system is improved without any communication link and extra hardware cost. The operation principle of the grid-tied inverter system is analyzed in detail with the implementation of the proposed control, and the design guidelines for key parameters are given and discussed. A prototype with three grid-tied inverters in parallel operation is built and experimental tests have been conducted on it in terms of steady-state performances and dynamic performances. The experimental results show that the operation modes of each grid-tied inverter depend on its sensing gain of the dc bus voltage. The European efficiency of the grid-tied inverter system with the conventional control and with the proposed control are 94.74% and 95.17%, respectively, which means the European efficiency has been enhanced by 0.43%. These results verify the feasibility and effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Fault-tolerant permanent magnet synchronous generator (PMSG) drives for wind turbine applications play a major role in improving reliability and availability levels, since power converters are very prone to fail. In this paper, a fault-tolerant converter with the ability to handle power switch open-circuit faults is addressed. The main concern of the proposed converter topology is the minimization of the hardware requirements, leading to a low increase of the system cost. First, the employed fault diagnostic technique does not require additional measurements, nor high computational effort. Secondly, the circuit topology reconfiguration implies a minimum number of extra components as well as minimal oversizing of the standard ones. Accordingly, a four-switch three-phase converter with the dc bus midpoint connected to the transformer neutral point and a three-switch three-phase rectifier are adopted for post-fault operation of the grid- and PMSG-side converters, respectively. Vector control strategies are proposed for both converters under analysis, focusing the issues of capacitor voltages balancing and torque ripple minimization. The performance of the proposed fault-tolerant PMSG drive is analyzed by means of experimental results. [ABSTRACT FROM PUBLISHER]

Utilization of power electronics converters in pulsed power applications introduced a new series of reliable, long life, and cost-effective pulse generators. However, these converters suffer from the limited power ratings of semiconductor switches, which necessitate introduction of a new family of modular topologies. This paper proposes a modular power electronics converter based on voltage multiplier as a high voltage pulsed power generator. This modular circuit is able to generate flexible high output voltage from low input voltage sources. Circuit topology and operational principles of proposed topology are verified via experimental and simulation results as well as theoretical analysis. [ABSTRACT FROM PUBLISHER]

Along with rapid advancement of power semiconductors, voltage multipliers have introduced new series of pulsed power generators. In this paper, based on conventional voltage multiplier and by using power electronics switches a new topology in high voltage pulsed power application is proposed. This topology is a modular circuit that can generate a high output voltage from a relatively low input voltage with fast rise time and adjustable frequency, pulse width, and voltage levels using a series connection of switched capacitor cells. A comparative analysis is carried out to show the advantages of proposed topology. Experimental and simulation results are presented to confirm the analysis. [ABSTRACT FROM AUTHOR]

A systematic method for deriving multiport converters (MPCs) from the full bridge (FB) converter (FBC) and bidirectional dc–dc converters (BDCs) is proposed in this paper through sharing the parasitized switching legs by the BDCs and the FBC. By employing the proposed method, families of FB and BDC-based MPCs (FB-BDC-MPCs), including some existing ones, are developed for renewable generation systems with the merits of simple topology, reduced devices, and single-stage power conversion. Voltage regulations between any two ports can be achieved by employing pulsewidth modulation and phase-angle-shift control scheme. Furthermore, zero-voltage switching for all the switches can be realized in the proposed FB-BDC-MPCs. A typical four-port converter developed by the proposed method, named buck/boost four-port converter (BB-FPC), is analyzed in detail as an example in terms of operation principles, design considerations, and control strategy. Experiments have been carried out on a 500-W prototype of BB-FPC, which demonstrate the feasibility and effectiveness of the proposed topology derivation method. [ABSTRACT FROM AUTHOR]

This paper discusses the operation of a multiphase system, which is aimed at both variable-speed drive and generating (e.g., wind energy) applications, using back-to-back converter structure with dual three-phase machine-side converters. In the studied topology, an asymmetrical six-phase induction machine is controlled using two three-phase two-level voltage source converters connected in series to form a cascaded dc link. The suggested configuration is analyzed, and a method for dc-link midpoint voltage balancing is developed. Voltage balancing is based on the use of additional degrees of freedom that exist in multiphase machines and represents entirely new utilization of these degrees. The validity of the topology and its control is verified by simulation and experimental results on a laboratory-scale prototype, thus proving that it is possible to achieve satisfactory dc-link voltage control under various operating scenarios. [ABSTRACT FROM PUBLISHER]

This paper presents an analytical design method for the dc collector systems of offshore wind farms and proposes an improved topology to overcome the limitations of the conventional series–parallel (SP) topology. During a severe failure in the SP topology, bypassing the faulty units imposes overvoltage on fault-free units and leads to the disconnection of the series branch from the collector system. By providing auxiliary connection paths, the suggested topology reduces the overvoltage of the units and hence maintains fault-free units operational following a severe failure. Hence, the efficiency of a wind farm increases considerably upon any failure occurrence. To show the merits of the suggested topology, the captured power during a failure has been calculated and fairly compared with that of the conventional SP topology, considering the excess cost of the suggested topology due to additional connection paths. To investigate the performances of both topologies and their feasibility, a collector system including 12 wind turbine generators has been simulated in time domain software environment. Then, various failure scenarios have been investigated to evaluate the transient behavior of the dc collector system following slight and severe failures. The study results reveal the feasibility of the proposed topology as a promising structure for future dc collector systems. [ABSTRACT FROM PUBLISHER]

This paper unifies the underlying concepts of all basic single-switch, two-state, dc-to-dc voltage-sourced converters, by duality, as generic related current and voltage-sourced converters. By using ac and dc circuit theory, the three basic converters can be transformed to yield all known transfer functions and realizes a proliferation of 33 topologies, three being previously unidentified topologies with unique characteristics. The circuit based systematic unifying approach offers new insight and an alternative interpretation to the origin of the 33 topologies including the Zeta, Cuk, \pmLuo, CSC, Landsman, and Sepic converters. Converter time-domain simulations and corresponding practical results of the three new topologies extol and culminate the concepts and analysis presented. [ABSTRACT FROM PUBLISHER]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

Three-phase dc/dc converters have the superior characteristics including lower current rating of switches, the reduced output filter requirement, and effective utilization of transformers. To further reduce the voltage stress on switches, three-phase three-level (TPTL) dc/dc converters have been investigated recently; however, numerous active power switches result in a complicated configuration in the available topologies. Therefore, a novel TPTL dc/dc converter adopting a symmetrical duty cycle control is proposed in this paper. Compared with the available TPTL converters, the proposed converter has fewer switches and simpler configuration. The voltage stress on all switches can be reduced to the half of the input voltage. Meanwhile, the ripple frequency of output current can be increased significantly, resulting in a reduced filter requirement. Experimental results from a 540-660-V input and 48-V/20-A output are presented to verify the theoretical analysis and the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents the hybrid seven-level cascaded active neutral-point-clamped (ANPC)-based multilevel converter. The converter topology is the cascaded connection of a three-level ANPC converter and an H-bridge per phase. The voltage of the H-bridge is actively maintained to the required level through selection of the switching states of the converter. The topology is operated under selective harmonic elimination pulsewidth modulation (SHE-PWM), maintaining the switching frequency of the converter to a minimum. The operating principles, voltage balancing methods, and limitations of the converter are analyzed together with extensive simulation results of the topology. Experimental results from a low-power laboratory prototype are presented that verify the operation of the hybrid converter under SHE-PWM. [ABSTRACT FROM PUBLISHER]

A three-port dc–dc converter integrating photovoltaic (PV) and battery power for high step-up applications is proposed in this paper. The topology includes five power switches, two coupled inductors, and two active-clamp circuits. The coupled inductors are used to achieve high step-up voltage gain and to reduce the voltage stress of input side switches. Two sets of active-clamp circuits are used to recycle the energy stored in the leakage inductors and to improve the system efficiency. The operation mode does not need to be changed when a transition between charging and discharging occurs. Moreover, tracking maximum power point of the PV source and regulating the output voltage can be operated simultaneously during charging/discharging transitions. As long as the sun irradiation level is not too low, the maximum power point tracking (MPPT) algorithm will be disabled only when the battery charging voltage is too high. Therefore, the control scheme of the proposed converter provides maximum utilization of PV power most of the time. As a result, the proposed converter has merits of high boosting level, reduced number of devices, and simple control strategy. Experimental results of a 200-W laboratory prototype are presented to verify the performance of the proposed three-port converter. [ABSTRACT FROM AUTHOR]

Unbalanced grids introduce performance deterioration for Vienna rectifier topology by producing twice fundamental frequency ripples in dc-link voltage and input active/reactive power. A common current reference generation for the purpose of eliminating the input power ripple, such as dual-frame hybrid vector control, can maintain constant input power and eliminate ripples in dc-link voltage under light voltage unbalanced grids. Under severe unbalanced grids, this type of a control method will fail to work. This paper first analyzes the theoretical operation area of a constant power control method under unbalanced grids, and then a novel control method is proposed. The proposed control method can work under severe unbalanced grids by injecting a small amount of input power ripple and balance the performance of working area and output dc voltage ripples. Finally, the experiment results using the constant power control method are given and validate the performance of the proposed control method. [ABSTRACT FROM PUBLISHER]

This paper proposes an LCL dc-dc converter concept which is capable of achieving very high stepping ratios with megawatt-level power transfers. The converter can find potential application in connecting high-power dc sources to high-voltage dc transmission including future dc transmission networks. This converter is based on two ac/dc insulated-gate bipolar transistor-based converters and an internal passive LCL circuit without internal ac transformers. The LCL circuit is designed to enable voltage stepping without any reactive power circulation and with potentially soft switching operation which minimizes the switching losses. The designed converter has the ability to achieve current regulation even under extreme external dc faults and, therefore, the converter can operate through dc faults. The switch utilization is better than similar topologies and losses are reasonably low. A dual-active-bridge transformer-based converter design is presented to compare with the proposed LCL converter. A detailed PSCAD model confirms conclusions using a 100-MW 20-kV/300 kV test system. An LCL 200-W 20-V/100-V dc/dc prototype converter is built to validate the proposed topology. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is based on the cascaded connection of identical submodules (SMs) enabling additional redundancies. This paper proposes the configuration of the MMC topology with redundant SMs and demonstrates the effects of active redundancies. The proposed configuration decreases the switching frequency per SM while reducing the SM capacitor voltage ripples. An analytical model for determining the SM capacitor voltage ripple and voltage dynamics is derived. The results from the analytical model are compared with the switching model for a 21-level MMC with five redundant (25 in total) SMs per arm. Experimental results based on a single-phase laboratory prototype with five SMs per arm and a single redundant cell further illustrate the operation and verify the derived mathematical model and simulation results. [ABSTRACT FROM AUTHOR]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Hybrid cascade multilevel inverters combine semiconductor devices of different voltage ratings and technologies, which theoretically allow high efficiency to be achieved. The bottlenecks of these topologies are, however, the need for isolated supplies for the cells and the lack of modularity. This paper focuses on the design and control of high-resolution, high-efficiency multilevel inverters with simplified dc power supplies. It introduces several rules for systematically designing the dc voltages of the cells, for which all unsupplied capacitor voltages can be regulated. Six classes of inverters are obtained covering single- and three-phase, staircase and pulsewidth-modulated (PWM) inverters. New configurations of hybrid cascade multilevel inverters are obtained for each class. A double modulation strategy with two different frequencies is proposed that allows switching losses of PWM inverters to be reduced. Decoupled mechanisms are proposed for the total and internal energy balances. It is shown how to make the design robust by taking into account conversion losses and large dc-voltage imbalances in the design and control. An analysis of the maximum voltage utilization and efficiency of the resulting configurations is carried out. The effectiveness of the novel concepts is validated experimentally for two of the proposed topologies. [ABSTRACT FROM PUBLISHER]

Voltage balance issue of dc-link capacitors is very important for applications of a cascade multilevel converter or a modular multilevel converter. In this paper, a novel diode-clamped modular multilevel converter (DCM2C) topology is proposed and a power feedback control method is developed. With the developed control strategy, the proposed diode-clamped circuit becomes a controllable closed loop which enables the capacitor voltages to be clamped by low power rating clamping diodes. The proposed topology and control strategy has quicker response and requires much fewer voltage sensors than the normally used traditional method; therefore, the system performance improvement and cost reduction are expected. Based on the proposed DCM2C, a novel N +1-level cascade multilevel topology is proposed for a cascade active power filter (CS-APF). The simulation and experimental results from the CS-APF have demonstrated and verified the effectiveness of the proposed novel topology and control method. [ABSTRACT FROM AUTHOR]

This paper proposes a new family of three-switch three-state single-phase Z-source inverters (TSTS-ZSIs) that can be classified into two groups, boost-based TSTS-ZSI and buck-boost-based TSTS-ZSI, according to the step-up circuit. All of the topologies have the merits of buck-boost capability and low voltage stress, and some of them have the feature of dual grounding. In addition, the step-up in dc side and inversion in ac side is completely decoupled in the proposed topologies. In terms of a linear voltage gain, the conventional linear control methods can be used, which makes the control system very simple. The operating principles of the two types of topologies are described, respectively, and the comprehensive comparison between them is provided. Finally, the theoretical analysis and comparison of the proposed topologies are verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents three topological classes of dc-to-dc converters, totaling nine converters (each class with three buck, boost, and buck-boost voltage transfer function topologies), which offer continuous input and output energy flow, applicable and mandatory for renewable energy source, maximum power point tracking and maximum source energy extraction. A current sourcing output caters for converter module output parallel connection. The first class of three topologies employs both series input and output inductance, while anomalously the other two classes of six related topologies employ only either series input (three topologies) or series output (three topologies) inductance. All nine converter topologies employ the same elements, while additional load shunting capacitance creates a voltage sourcing output. Converter time-domain simulations and experimental results for the converters support and extol the concepts and analysis presented. [ABSTRACT FROM AUTHOR]

An improved buck power factor correction (PFC) converter topology is proposed in this paper. By adding an auxiliary switch and two diodes, the dead zones in ac input current of traditional buck PFC converter can be eliminated. An improved constant ON-time control is proposed and utilized in this improved buck PFC converter to force it that operates in critical conduction mode (CRM). With optimal control parameters, nearly unit power factor can be achieved and the input current harmonics can meet the IEC61000-3-2 class C standard within the universal input voltage range. Moreover, the efficiency of the proposed converter is not deteriorated compared to the conventional buck converter. Detailed theoretical analysis and optimal design considerations for the proposed converter are presented and verified by a 100-W lab-made prototype. [ABSTRACT FROM AUTHOR]

Parallel operation is an effective way to improve the capacity of full power converter in permanent-magnet direct-drive wind power generation system. But it causes the zero-sequence circulating-current (ZSCC), which brings current discrepancy, current waveform distortion, power losses, and electromagnetic interference (EMI), etc. The paper proposes a new topology of full power converters which are composed of n full power converters. The n converters have the same structures and are in parallel with each other. Besides, the average models of the system are analyzed and the fundamental mechanism of ZSCC generation is given. Based on the above analysis, the control strategy of the system is designed. The simulation and experiment results of two parallel full power converters show the feasibility of the proposed theory and control scheme. [ABSTRACT FROM PUBLISHER]

Conventional dynamic voltage restorers (DVRs) are connected to the power grid through power-frequency transformers. These bulky and costly transformers cause voltage drop and power losses. In this paper, a high-frequency-link dynamic voltage restorer (HFL-DVR) is proposed based on transformer-isolated topologies. This topology facilitates independent operation conditions for each phase in a three-phase system. It enjoys relatively low cost, low losses, and small size. Also, it is free from transformer inrush currents. Small-signal ac equivalent circuit for the power stage including HFL-DVR is derived based on an averaged modeling approach. Transfer functions are obtained to study the effect of inputs such as dc-link voltage, grid voltage, and the load current on the output of HFL-DVR. In order to obtain acceptable properties such as transient overshoot, setting time, and steady-state error, a PID controller is added to the system. This shows that the effect of disturbances on the output of HFL-DVR can be reduced. The experimental results are obtained from a 220V/50Hz HFL-DVR setup. The simulation and experimental results have been compared to verify theoretical aspect of the proposed DVR for both symmetrical and asymmetrical voltage sag conditions. [ABSTRACT FROM AUTHOR]

Multilevel converters can reach medium-voltage operation increasing the efficiency of high-power applications. Among the existing multilevel converter topologies, the modular multilevel converter (MMC) provides the advantages of high modularity, availability, and high power quality. Moreover, the main advantage compared to cascaded multilevel converters is the lack of an input transformer which results in a reduction of cooling requirements, size, and cost. One of the drawbacks of this topology when used as an ac–ac converter is the input and output frequency components in the control loop, resulting in a more complex controller design. In this paper, a single-phase ac–ac MMC predictive control approach is proposed. The controller minimizes the input, output, and circulating current errors and balances the dc voltages. Experimental results show the performance of the proposed predictive control scheme. [ABSTRACT FROM PUBLISHER]

A modified single-phase quasi-Z-source ac-ac converter is proposed in this paper. The proposed converter has the main features in that the output voltage can be bucked or boosted and be both in-phase and out-of-phase with the input voltage. The input voltage and output voltage share the same ground, the size of a converter is reduced, and it operates in a continuous current mode. A safe-commutation strategy for the modified single-phase quasi-Z-source ac-ac converter is used instead of a snubber circuit. The operating principles and a steady-state analysis are presented. A laboratory prototype, tested using a resistive load, a passive load, and a nonlinear load, was constructed that used an input voltage of 70 Vrms /60 Hz in order to verify the performance of the modified single-phase quasi-Z-source ac-ac converter. The experimental results verified that the converter has a lower input current total harmonic distortion, a higher input power factor, and a higher efficiency in comparison to a conventional single-phase Z-source ac-ac converter. In addition, the experimental results show that the use of the safe-commutation strategy is a significant improvement, as it makes it possible to avoid voltage spikes on the switches. [ABSTRACT FROM AUTHOR]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new topology for bidirectional multiinput direct dc–ac converter for clean-power-generation system, therefore, at the input port, a boost converter is used to meet the requirement of many distributed generation systems, such as photovoltaic, and fuel cell systems. The boost converter can increase the dc input voltage. This point results in a turn ratio reduction of high-frequency isolating link transformer. Furthermore, the boost inductor reduces the input current ripple, therefore, the saturation of the transformer can be avoided for higher output currents. The count of used devices has been reduced in the proposed converter. As a result, the cost, size, and the volume of the converter can be reduced. The reduced conversion steps increase the efficiency of the converter. The converter is analyzed step by step to show the principles of the operation in providing energy management based on duty-cycle variations. The system capability in different operation conditions has been simulated, and the simulation results have been compared with measurement results. Dynamic analysis and control design of the bidirectional dc–ac converter is presented based on nonlinear control by input–output feedback linearization. [ABSTRACT FROM AUTHOR]

A novel three-phase diode boost rectifier is proposed in this paper. The core of the proposed topology is a power conversion device [the loss-free transformer (LFT)] with two terminals; one input and one output. The input is parallel-connected with the dc bus capacitor, while the output is connected between the rectifier plus rail and the dc bus plus rail. The LFT is controlled in such a way to control the rectifier current and boost the dc bus voltage. In contrast to the ordinary boost rectifiers, the switches of the new boost rectifier are rated on a fraction of the dc bus voltage and a fraction of the input current. It makes this topology very compact and efficient. Power rating, size, and losses depend strongly on the ratio of the dc bus voltage to rectifier voltage (boosting factor). For example, if the boosting factor is low, below 1.5, the power converter efficiency could be 98–99%. The proposed boost rectifier has been analyzed and experimentally verified on a 5.5-kW prototype. The results are presented and discussed. [ABSTRACT FROM AUTHOR]

The solid-state transformer (SST) is one of the key elements in power electronic-based microgrid systems. The single-phase SST consists of a modular multilevel ac–dc rectifier, a modular dual active bridge (DAB) dc–dc converter with high-frequency transformers, and a dc–ac inverter stage. However, due to dc bus voltage and power unbalancing in each module, the modular SST often presents instability problems making its design difficult and causing unpredictable behavior. Moreover, the unbalanced dc-link voltages increase the stress of the semiconductor devices, and also cause high harmonic distortions of grid current, therefore, necessitating the use of a bigger ac filter. This paper presents a novel single-phase d–q vector-based common-duty-ratio control method for the multilevel rectifier, and a voltage feedforward and feedback based controller for the modular DAB converter. With the proposed control methods, the dc-link voltage and power in each module can be balanced. In addition, the low-distortion grid current, unity power factor, and bidirectional power flow can be achieved. Simulation and experimental results are presented to validate the proposed control methods. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge converters have found industrial application in the medium-voltage high-power range. In this paper, a generalized modulation technique for this type of converter based on a multidimensional control region is presented. Using the multidimensional control region, it is shown that all previous modulation techniques are particularized versions of the proposed method. Several possible solutions to develop a specific implementation of the modulation method are addressed in order to show the potential possibilities and the flexibility of the proposed technique. In addition, a feedforward version of this technique is also introduced to determine the switching sequence and the switching times, avoiding low harmonic distortion with unbalanced dc voltages. Experimental results are shown in order to validate the proposed concepts. [ABSTRACT FROM AUTHOR]

AC test power sources are essential for testing electric equipment that is ac-mains connected. Typically, linear power amplifiers (LPAs) are mainly employed as ac test sources because of their high fidelity and excellent dynamic behavior. However, these LPAs have very high losses in their output stages, which make the systems bulky and expensive due to the large heatsinks that are required. In recent years, two approaches have attracted popular interest to improve the efficiency of ac power sources. These are hybrid operation, i.e., combination of linear and switch mode, and multilevel switch-mode inverters. In this paper, three types of multilevel power amplifiers, based on hybrid or switching technology, are presented, namely: hybrid multicell amplifier (H-MCA), amplitude-modulated (AM) + pulsewidth-modulated (PWM) MCA (AP-MCA), and PWM MCA (P-MCA). For each of these topologies, the operating principle and control scheme are introduced. Finally, a 1-kVA laboratory prototype, which can realize all the three topologies, is built, and the measured performance based on this universal prototype are compared. [ABSTRACT FROM PUBLISHER]

A novel H-bridge multilevel pulsewidth modulation converter topology based on a series connection of a high-voltage diode-clamped inverter and a low-voltage conventional inverter is proposed in this paper. A dc link voltage arrangement for the new hybrid and asymmetric solution is presented to have a maximum number of output voltage levels by preserving the adjacent switching vectors between voltage levels. Hence, a 15-level hybrid converter can be attained with a minimum number of power components. A comparative study has been carried out to present high performance of the proposed configuration to approach a very low total harmonic distortion of voltage and current, which leads to the possible elimination of the output filter. Regarding the proposed configuration, a new cascade inverter is verified by cascading an asymmetrical diode-clamped inverter, in which 19 levels can be synthesized in output voltage with the same number of components. To balance the dc link capacitor voltages for the maximum output voltage resolution as well as synthesize asymmetrical dc link combination, a new multi-output boost converter is utilized at the dc link voltage of a seven-level H-bridge diode-clamped inverter. Simulation and hardware results based on different modulations are presented to confirm the validity of the proposed approach to achieve a high-quality output voltage. [ABSTRACT FROM PUBLISHER]

In this paper, a three-level three-leg ac–dc–ac converter for single-phase applications is investigated. The operating principles and control strategies for the topology are presented. It is shown that dc-link voltage balancing and its reduction are important objectives in the system design. The proposed pulsewidth modulation (PWM) strategy permits the dc-link capacitor voltage balance and also its reduction. The three-level converter is compared to the two-level converter in terms of rms switch currents, harmonic distortion, losses, and costs. Experimental and simulation results are presented to validate the theoretical studies. [ABSTRACT FROM PUBLISHER]

This paper presents a three-stage 18-level inverter design with a novel control method. The inverter consists of a series-connected main high-voltage, medium-voltage, and low-voltage stages. The high-voltage stage is made of a three-phase, six-switch conventional inverter. The medium- and low-voltage stages are made of three-level inverters constructed by H-bridge units. The proposed control strategy assumes a reference-input voltage vector and aims to operate the inverter in one state per sampling time to produce the nearest vector to that reference. The control concept is based on representing the reference voltage in 60^\circ-spaced two-axis coordinate system. In this system, the inverter vectors’ dimensions are integer multiples of the inverter's dc voltage, and the expression of the inverter's vectors in terms of its switching variables is straightforward. Consequently, the switching signals can be obtained by simple fixed-point calculations. The approach of the proposed control strategy has been presented, the transformed inverter vectors and their relation to the switching variables have been defined, and the implementation process has been described. The test results verify the effectiveness of the proposed strategy in terms of computational efficiency as well as the capability of the inverter to produce very low distorted voltage with low-switching losses. [ABSTRACT FROM PUBLISHER]