Search

Herein, three types of multihierarchical lattice structures (MHLSs) with different configurations are designed based on the body‐centered‐cubic (BCC) unit cell. The designed lattice structures are fabricated using Ti‐6Al‐4 V powder as feedstock material through selective laser melting (SLM) technology. The microstructure and surface morphology of the SLM‐formed samples are observed by optical microscopy and scanning electron microscopy, respectively. Theoretical calculation and quasistatic compression experiment are carried out to investigate their mechanical properties. The result shows that the size error of slave cell with small strut diameters is greater than that of master cell with larger strut diameters. All MHLSs exhibit superior mechanical properties compared to the BCC lattice structure. Moreover, the specific elastic modulus and specific yield strength of MHLSs with the best mechanical properties are 70.1% and 51.0% higher than that of BCC lattice structure, respectively. Meanwhile, theoretical calculation results of the elastic modulus and yield strength are consistent with the results of quasi‐static compression testing. The fracture morphology analysis indicates that the struts of the MHLSs samples exhibit a mixed brittle–plastic fracture mode, while the nodes exhibit a plastic fracture mode. [ABSTRACT FROM AUTHOR]

Menispermaceae is one of the core groups of Ranunculales. The single fertile ovule in each ovary in Menispermaceae varies greatly in integument number, micropyle formation, and integument lobe. However, data regarding ovule morphogenesis in the family are very limited. In this study, we document ovule development of selected species in the Menispermaceae using scanning electron microscopy and light microscopy. Ovule development in Menispermaceae shows the following characteristics. Two ovules are initiated in a young carpel, one of them degenerates gradually and the other develops into a fertile ovule in subsequent stages. Bitegmic in Sinomenium Diels. and Cocculus DC. and unitegmic in Stephania Lour. The formation of unitegmy is probably due to integumentary shifting. The annularly initiated inner integument is of dermal origin and has 2–3 cell layers in the family, but the semi‐annularly initiated outer integument is of both dermal and subdermal origin. Both inner and outer integument are cup‐shaped at maturity. The cup‐shaped outer integument is formed due to the outer integument's extension to the concave (adaxial) side of the funiculus. The obturator is well developed and consists of 2–3 cell layers in Cocculus or 9–11 cell layers in Stephania. Ovule development of Menispermaceae suggests some common characteristics between Cocculus and Sinomenium, and derived unitegmy supports molecular data that indicate Stephania is one of the late‐diverging lineages in the family. Integument lobations are present. The sterile ovule shows variations in the degeneration process. These results will provide evidence for exploring the evolution of ovules in Ranunculales. [ABSTRACT FROM AUTHOR]

In this study, we investigate the influence of absorber thickness on Cu2ZnSnS4 (CZTS) solar cells, ranging from 500 to 2000 nm, with nearly constant metallic composition. Despite the observed ZnS and SnS phases on the surface and backside of all absorber films, scanning electron microscopy, Raman scattering, and X-ray diffraction show no large variations in material quality for the different thicknesses. The open-circuit voltage ( Voc), short-circuit current and overall power conversion efficiency of the fabricated devices show an initial improvement as the absorber thickness increases but saturate when the thickness exceeds 750 nm. External quantum efficiency (EQE) measurements suggest that the current is mainly limited by collection losses. This can result from non-optimal bulk quality of the CZTS absorber (including the presence of secondary phases), which is apparently further reduced for the thinnest devices. The observed saturation of Voc agrees with the expected influence from strong interface recombination. Finally, an effective collection depth of 750-1000 nm for the minority carriers generated in the absorber can be estimated from EQE, indicating that the proper absorber thickness for our device process is approximately 1000 nm. Performance could be improved for thicker films, if the collection depth can be increased. [ABSTRACT FROM AUTHOR]

Floral morphogenesis and the development of Cercidiphyllum japonicum Sieb. et Zucc. were observed by scanning electron microscopy (SEM). The results showed that the pistillate inflorescences were congested spikes with the flowers arranged opposite. Great differences between the so-called “bract” and the vegetative leaf were observed both in morphogenesis and morphology. In morphogenesis, the “bract” primordium is crescent-shaped, truncated at the apex and not conduplicate, has no stipule primordium at the base but does have some inconspicuous teeth in the margin that are not glandular. The leaf primordium is triangular, cycloidal at the apex, conduplicate, has two stipule primordia at the base, has one gland-tooth at the apex occurring at first and some gland-teeth in the margin that occur later. In morphology, the “bract” is also different to the vegetative leaf in some characteristics that were also illustrated in the present paper. Based on the hypothesis that the bract is more similar to the vegetative leaf than the tepal, we considered that the so-called “bract” of C. japonicum might be the tepal of the pistillate flower in morphological nature. Therefore, each pistillate flower contains a tepal and a carpel. We did not find any trace of other floral organs in the morphogenesis of the pistillate flower. Therefore we considered that the unicarpellate status of extant Cercidiphyllum might be to highly reduce and advance characteristics that make the extant Cercidiphyllum isolated from both fossil Cercidiphyllum-like plants and its extant affinities. [ABSTRACT FROM AUTHOR]