Search

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

However, curtailment compensation costs eventually surpass upgrade costs, making network upgrades a practical option once the HC level reaches 118%, 106%, and 97% for rural, suburban, and urban regions, respectively. Keywords: distribution networks; renewable energy sources EN distribution networks renewable energy sources 3763 3764 2 09/05/23 20230901 NES 230901 Decarbonization policy leads to an increasing trend of integration of renewable energy sources (RESs) in distribution grids. [Extracted from the article]

The distribution system is easily affected by extreme weather, leading to an increase in the probability of critical equipment failures and economic losses. Actively scheduling various resources to provide emergency power support can effectively reduce power outage losses caused by extreme weather. This paper proposes a mobile energy storage system (MESS) scheduling strategy for improving the resilience of distribution networks under ice disasters. First, the influence of wind and ice loads on power transmission lines is analyzed, and a detailed fault statistical model of transmission lines under an ice disaster is established. Then, the MESS scheduling problem considering the coupling of transportation-distribution networks is transformed into a two-stage optimization problem. The first stage determines the optimal configuration scheme for MESS, and in the second stage, the optimal path selection for MESS can be obtained. Finally, the effectiveness and feasibility of the algorithm proposed in this paper are verified through an improved IEEE-33 node testing system. [ABSTRACT FROM AUTHOR]

This paper proposes a two‐stage stochastic scheduling model for urban distribution network resilience enhancement against ice storms, which coordinates mobile deicing equipment routing and distributed energy resources dispatching. An improved line ice thickness prediction model and a photovoltaic power generation prediction method in accordance with conditional generative adversarial networks are proposed to provide data boundaries for scheduling strategy. Facing the uncertainty of line failure, a two‐stage scenario‐based distribution network optimization model is established. At first stage, the mobile deicing equipment routing strategy is decided to mitigate the impact caused by ice storms. The Monte‐Carlo simulation method is introduced to describe the uncertainty of line failure due to ice acceleration. For the second stage, based on the results of photovoltaic forecasting and possible distribution line failure scenario generated by Monte‐Carlo simulation method, the optimal distributed energy resources dispatching strategy can be obtained through the mixed integer programming. The proposed model is simplified to a mixed integer linear programming model that can be solved by a commercial solver. The test results on the modified IEEE 33‐node system and modified 69‐node system demonstrate that the proposed method can effectively improve the resilience performance of urban distribution network under ice storms. [ABSTRACT FROM AUTHOR]

Cyber–physical distribution systems with renewable energy should have high resilience under extreme conditions. However, in a distribution system with deep cyber–physical coupling, the propagation of information risk impairs the resilience of the system. This paper proposes a strategy to improve the resilience of cyber–physical distribution systems that considers cross‐space propagation of information risk. First, the mechanism for interaction between the cyber space and physical space is analyzed, and an information risk cross‐space propagation model is proposed. Second, the risk status of key device nodes is quantified according to the risk propagation model, and an optimization strategy for information risk control is obtained, whose objective function is the minimum risk of the coupling network. Third, a fault restoration strategy that considers cyber space risk is proposed. Finally, the paper reports experiments using the modified IEEE 33‐node and 123‐node distribution networks to simulate the proposed strategy and verify its effectiveness. [ABSTRACT FROM AUTHOR]

Air‐insulated switchgear plays an important role in distribution network and partial discharge (PD) is one of the common faults in its operation. The method of gas component analysis, which is to detect chemical gas products, is a novel one to discover PD. In order to study the feasibility of the method, the monitoring experiment of characteristic gases, comprising carbon monoxide (CO), nitrogen dioxide (NO2), and ozone (O3), of metal protrusion PD is carried out. This paper conducts the comparative experiments on three main factors affecting PD: voltage, air humidity and degree of protrusion, as well as studies how they affect the formation of characteristic gases. According to the experimental result, higher applied voltage promotes the formation of characteristic gases in the same conditions. In addition, with the increase of humidity from 40% to 75%, the generation of gases is inhibited. Furthermore, when the needle–plate distance is 30 mm, the gas concentration has almost no change within 6 h, which is different from that of 10 mm. In conclusion, the difference in gases concentration reveals the influence of three main factors on the generation of characteristic gases and provides an analytical basis for PD detection by gas composition analysis. [ABSTRACT FROM AUTHOR]

Increasing the penetration level of distributed generation (DG) units requires overcoming the technical challenges associated with their integration into the distribution systems, especially protection problems. Change in the current profile of the distribution system due to the presence of DG units disrupts the operation of the conventional fuse saving coordination (FSC) scheme. The first objective of this paper is to provide an overview of the state‐of‐the‐art of FSC schemes in distribution systems with distributed generators that has not been systematically presented yet. In addition to comparing the features of reliability, cost, speed, implementation, calculation burden, and requirements, the impact of presence of distributed generations on the performance of the conventional FSC scheme is investigated in details. The second objective of this paper is to propose an FSC restoration scheme for minimizing the challenges of previous works. Using a quasi‐voltage current term, the proposed scheme modifies the adjustable time coefficient of the recloser in two ways of pro and plus. The former scheme provides an approximate FSC with a simple setting while the latter scheme provides complete coordination at the expense of a more complex setting. No need for voltage measurement makes its implementation practical in available distribution systems. The effective performance of the proposed FSC scheme is verified through extensive simulation studies in the ETAP environment. [ABSTRACT FROM AUTHOR]

A power line carrier (PLC) communication characteristics‐based method is proposed for single‐phase‐to‐ground fault location in neutral isolated medium voltage meshed distribution networks in this paper. The carrier signals with a time‐varying frequency and constant amplitude are processed by a set of PLC transmitters and receivers, whose placement is optimized by regarding the power network as an undirected graph. Two signal encoding and decoding algorithms for the PLC terminals are proposed to avoid using expensive timing systems between the terminals. The fault location technique is implemented by comparing the cosine similarity of amplitude attenuation and phase offset between the fault and a feature library. The node corresponding to the maximum cosine similarity of the characteristics between the present fault and the library is selected as the location of the current fault. Only one set of low‐cost PLC communication terminals and the widely available power lines are needed in the fault location system, making this approach highly practical. Numerical simulations using MATLAB/Simulink have been performed to verify the technique's feasibility. The results show that the method can accurately locate faults in neutral isolated medium voltage meshed distribution networks. Besides, the presented approach achieves a high level of accuracy in estimating transition resistance values. [ABSTRACT FROM AUTHOR]

With the increasing integration of distributed energy resources (DERs) into distribution systems, the optimization of system operation has become complex, facing challenges such as inadequate consideration of market participants' benefits, poor computational efficiency, and data privacy concerns. This paper introduces the concept of a virtual power plant (VPP) as a solution for energy integration and management. To strike a balance between operational safety and the interests of market participants, a dual‐layer model is proposed. This model considers the benefits of both Distribution System Operators (DSO) and VPP, while also enhancing the consideration of distribution network constraints. The DSO considers AC optimal power flow and utilizes penalty functions to ensure network security in case of violations. To enhance computational efficiency and privacy, the paper presents the parameter‐sharing twin delayed deep deterministic policy gradient approach. This approach allows multiple intelligent agents to share a neural network model, effectively reducing the computational load. During the training process, only essential data is exchanged among the agents, ensuring the privacy of sensitive information. The effectiveness of the proposed model and the algorithm is validated through a case study on an IEEE 33‐node system. [ABSTRACT FROM AUTHOR]

Earth faults is a challenging fault type to locate in resonant grounded networks due to their naturally low fault current, and the problem increases with an increased fault impedance. This paper describes the detailed implementation and laboratory testing of a method for detection, location and clearing of earth faults with very small fault currents. The method consists of two indicators used in the fault detection stage, where their simultaneous operation ensures selective fault detection and faulty feeder selection. One of these indicators also enables continuous fault indication throughout a sectionalizing process. The laboratory tests demonstrate that both indicators function as intended, and it is the current sensors which ultimately limit the attainable sensitivity. Faults up to 15 kΩ were detected successfully in the laboratory network based on phase current measurements, while the sectionalizing indicator showed much higher sensitivity and functioned as intended in a 50 kΩ fault. Measurements from one field test in a 22 kV network corroborate the laboratory results and demonstrate the expected earth fault indicator response. [ABSTRACT FROM AUTHOR]

This paper emphasizes the integration of wind and photovoltaic (PV) generation with battery energy storage systems (BESS) in distribution networks (DNs) to enhance grid sustainability, reliability, and flexibility. A novel multi‐objective optimization framework is introduced in this study to minimize energy supply costs, emissions, and energy losses while improving voltage deviation (VD) and voltage stability index (VSI). The proposed framework comprising normal boundary intersection (NBI) and decomposition‐based evolutionary algorithms (DBEA) determines the optimal siting and sizing of renewable‐based distributed resources, considering load demand variations and the intermittency of wind and solar outputs. The comparative analysis establishes that the proposed strategy performs better than many contemporary algorithms, specifically when all the objective functions are optimized simultaneously. The validation of the proposed framework was carried out on the standard IEEE‐33 bus test network, which demonstrates significant percentage savings in energy supply costs (49.6%), emission rate (62.2%), and energy loss (92.3%), along with enormous improvements in VSI (91.9%) and VD (99.8953%). The obtained results categorically underline the efficiency, reliability, and robustness of the proposed approach when employed on any complex distribution network comprising multiple renewable energy sources and battery storage systems. [ABSTRACT FROM AUTHOR]

Distribution system (DS) communication failures following extreme events often degrade monitoring and control functions, thus preventing the acquisition of complete global DS component state information, on which existing post‐disaster DS restoration methods are based. This paper proposes methods of inferring the states of DS components in the case of incomplete component state information. By using the known DS information, the operating states of unobservable DS branches and buses can be inferred, providing complete information for DS performance restoration before full communication recovery. [ABSTRACT FROM AUTHOR]

This paper introduces a Fuzzy Logic Controller designed for an on-load tap changer within medium voltage distribution systems with bulk penetration of Distributed Energy Resources. As the on-load tap changer remains one of the most essential forms of voltage regulation in medium voltage distribution networks, improving its operation is a cost-effective response to the emerging voltage violations caused by intermittent generation during the early stages of the energy system transformation. Software-in-the-loop simulations were conducted to validate the effectiveness of the proposed algorithm compared to the conventional methods. A modified CIGRE Medium Voltage Distribution Network Benchmark in European Configuration was modelled while the controller code developed in Python 3.12 was running on a PC, both coupled in a real-time closed-loop environment. The analyses showed that the proposed algorithm managed to reduce overvoltage from 7.02% to 4.85% in the benchmark network, thus demonstrating that the algorithm is efficient and ready for on-field implementation. [ABSTRACT FROM AUTHOR]

The modernization of the current electric power grid into a smart grid requires the integration of advanced instrumentation, automation, and communication technologies to optimize efficiency, safety, and reliability. In traditional power grids, communication and control tasks are concentrated in substations, limiting their coverage to high-power equipment. As distributed energy resources increase in different sections of the grid, power flow becomes bi-directional. This requires monitoring and control at the Transmission and Distribution (T&D) level, which forms the largest portion of the power grid. To achieve efficient energy flow management and enable consumer participation in demand management, the integration of information and communication technologies (ICTs) is essential. Wireless sensor networks (WSNs) have been identified as a suitable solution for communications within the distribution network. An ongoing challenge, however, is the definition of the best candidates to solve this problem, among the currently available wireless technologies. This paper reviews different wireless communication technologies that provide robustness, reliability, speed, scalability, and cost-effectiveness for monitoring distribution lines. An outline of the architecture for smart grid communications, the definition of sensor network requirements for power line environments, and an overview of specific studies focusing on technology comparisons are the main contributions of this paper. The purpose of this review is to delineate current technologies in order to establish potential future research directions within the field. [ABSTRACT FROM AUTHOR]

The upcoming network investment decisions and regulatory framework adopted by distribution system operators (DSOs) are most likely to be impacted by the integration of fluctuating distributed generation. The economical hosting capacity (HC) improvement method is investigated in this paper as a trade‐off between curtailment and upgrade using a Monte Carlo simulation procedure. The associated costs of both methods are vital indicators for network operators that are trying to maximize the HC and minimize cost. In addition, the breakeven point where curtailment and upgrade costs intersect is the decisive point at which network upgrade becomes sensible as marginal curtailment cost exceeds upgrade cost. A shift in global climate conditions can impact the photovoltaic (PV) levels that motivate network operators to investigate PV penetration, especially in colder climate regions. Thus, the primary objective of this paper is to investigate the shift of the breakeven point to guide DSOs to either adopt PV curtailment as a temporary measure or grid upgrade as a risk aversion strategy considering Finnish climate and load patterns. The real‐time load and PV generation data are utilized for the simulations to consider the dynamic performance indication of three Finnish distribution networks. Curtailment remains a low‐cost option to obtain a percentage HC rise of 13%, 7%, and 8% for rural, suburban, and urban regions, respectively, beyond which curtailment compensation cost surpasses upgrade cost. In essence, PV curtailment serves as an immediate and least‐cost solution to relieve network violations and defer network investment until the HC level (118%, 106%, 97%) making the upgrade a practical option afterwards. [ABSTRACT FROM AUTHOR]

There exist problems of hard coordination and threshold setting as well as low sensitivity in overcurrent relay due to the bidirectional and small fault current when distributed generators are integrated into the distribution network. This paper introduces ferrite rings (FRs) to act as boundaries of distribution feeders, and a peak time of voltage traveling wave‐based protection is proposed. The characteristics of FRs are analyzed and their feasibility as line boundary is validated. The fault characteristics of internal and external faults are analyzed when FRs are installed at both ends of the protected feeder. The results show that the peak time of the voltage travelling wave of the internal fault is far smaller than that of the external faults. According to the difference, the fault detection method and the protection scheme are proposed. Simulations in PSCAD and experiment validate that the proposed protection principle can reliably distinguish between internal and external faults. Besides, the proposed protection scheme has higher sensitivity compared to ROCOV‐based protection. [ABSTRACT FROM AUTHOR]

This paper presents an analysis of the fault current contributions of small‐scale single‐phase photovoltaic inverters under grid‐connected operation and their potential impact on the protection of distribution systems. To conduct this analysis, an autotransformer‐based voltage dip generator is proposed as a means to test the photovoltaic inverters' contribution to short‐circuit currents. Laboratory tests are then performed to obtain the short‐circuit current contribution of eight single‐phase photovoltaic inverters. Using the short‐circuit current data obtained, a behaviour model is developed and simulated on Matlab‐Simulink. The model is then applied to a real distribution system and case studies are conducted to simulate the potential impacts on the protection system. Results indicate that while the massive penetration of small‐scale single‐phase photovoltaic inverters can alter the protection system's operating time, the impacts are not significant. Only in very specific scenarios, such as events related to high impedance faults, some impact can be observed. In these situations, the presence of photovoltaic inverters further complicates the already difficult task of identifying high impedance faults through conventional overcurrent protections. This study provides valuable insights into the integration of photovoltaic inverters into distribution systems, and can aid in the development of effective protection measures for future grid designs. [ABSTRACT FROM AUTHOR]

The ongoing electrification of road transportation sector, which is expected to continue to strongly increase over the next years, will result in the connection of a significant number of electric vehicle (EV) chargers in LV and MV distribution networks, particularly in residential applications with on‐board ("slow") EV chargers. In order to evaluate loading limits of existing distribution networks for the maximum number of EV chargers that can be safely connected (commonly denoted as a network EV "hosting capacity", HC), this paper introduces a general approach to determine one commonly used network design parameter (after‐diversity maximum demand, ADMD) and one new parameter (maximum daily energy demand, MDED), which are both obtained from the load profiles of maximum per‐hour demands for uncontrolled residential EV charging. The presented approach uses actual EV charging data from the UK as the inputs in Monte Carlo simulations to generate daily EV charging profiles for arbitrary numbers of EVs, enabling to identify related ADMD, MDED and per‐hour maximum demand values, as well as their seasonal variations. The assessed ADMD, MDED and hourly maximum EV charging demands for uncontrolled EV charging are then combined with available UK residential daily load profiles before the EVs are connected ("pre‐EV demands"), where their combined coincidental and noncoincidental maximum demands are evaluated against the static thermal rating (STR) and dynamic thermal rating (DTR) loading limits of network components (transformers and overhead lines), taking into account relevant weather/ambient conditions. This is denoted as a network HC for uncontrolled EV charging. Finally, evaluating the resulting per‐hour maximum demand values against the STR and DTR loading limits and MDED values allows to select one particular scheduling method for controlled EV charging, which gives the absolute maximum number of EVs that can be safely connected in the considered network, that is, maximum network HC for fully controlled EV charging. The presented approach is illustrated on the example of the IEEE 33‐bus test network (modelled using typical UK network components), for the pre‐EV residential demands taken from the recordings at a UK MV substation, and for ambient data taken from a UK Met Office weather station. Obtained results allow to evaluate the range of network EV HC values for uncontrolled and controlled EV charging, that is, lower and upper HC limits, which can be correlated with the commonly used allocations of the firm and non‐firm network HC, respectively. [ABSTRACT FROM AUTHOR]

The occurrence of natural disasters has led to an alarming increase in power interruptions, with severe impacts. Compounding this problem is the uncertain nature of data, which presents significant challenges in enhancing the resiliency of power distribution systems following such events. To tackle these issues, this paper introduces a robust optimization approach for improving the resiliency of power distribution systems. The approach encompasses crew teams for switching actions as part of the restoration process, along with demand response programs and mobile generators (MGs). By simultaneously leveraging these elements and considering the uncertainty associated with electrical load and electrical price, the resiliency of the system is enhanced. The objective function is tri‐level, comprising minimum, maximum, and minimum functions. At the first level, the approach minimizes the cost of commitment of combined heat and power plants (CHPs) by taking into account the location of MGs and the reconfiguration structure in power distribution systems. The second level aims to identify the worst‐case scenario for the uncertainty variables. Finally, the third level focuses on minimizing the total operation cost under the worst‐case scenario using demand response programs. The proposed algorithm is implemented on an IEEE 33‐bus test distribution system, with four different cases investigated. [ABSTRACT FROM AUTHOR]

Flexible DC distribution networks have been widely developed because of their advantages of high efficiency, low cost, and easy access to renewable energy. However, as distribution networks have more ends than the two-terminal transmission line, it is more challenging to protect them and locate their faults. Therefore, this paper proposes a modified T-source circuit breaker to protect against DC faults. Based on the proposed circuit breaker, an integral fault location method using double-terminal asynchronous data is proposed. The accuracy of the algorithm is not affected by the fault resistance. There are no differential terms in the algorithm, which greatly reduces the sensitivity to noise. The integral algorithm can remain steady when the voltage and current are zero in oscillation and attenuation periods. This constitutes the main contribution of this paper. Finally, it is verified by simulation and experiment that the proposed circuit breaker can isolate the power source within a short time in the typical DC distribution network. Under a noise of 30 dB for simulation, the location error of the proposed algorithm is <0.4% when the fault resistance is 0.5 Ω–500 Ω. [ABSTRACT FROM AUTHOR]

Leveraging distributed resources to enhance distribution network (DN) resilience is an effective measure in response to natural disasters. However, the willingness and economy of distributed resources are typically ignored. To address this issue, this paper proposes an emergent trading framework that uses parking lots (PLs) as resources to provide power support to critical loads (CLs) in a blackout due to typhoons. In this trading framework, an evolutionary Stackelberg game‐based trading model is established to consider maximizing all stakeholders' economic benefits, considering possible resources isolation under typical fault scenarios caused by typhoons, and a benefit allocation mechanism is proposed for all stakeholders to motivate all stakeholders to participate in the trading. This framework allows that critical loads could reduce their load loss, parking lots could receive adequate compensation to stimulate them to participate in the trading, and distribution utility could ensure its economic benefits. Furthermore, an iterative evolutionary‐Stackelberg solution set‐up is applied to obtain the equilibria of the proposed framework. Simulation results on the modified IEEE 69‐bus test system and IEEE 123‐bus test system reveal the validity of the proposed method. [ABSTRACT FROM AUTHOR]

State estimation (SE) of distribution networks heavily relies on pseudo measurements that introduce significant errors, since real-time measurements are insufficient. Interval SE models are regularly used, where true values of system states are supposed to be within the estimated intervals. However, conventional interval SE algorithms cannot consider the correlations of same interval variables in different terms of constraints, which results in overly conservative estimation results. In this paper, we propose a new interval SE model that is based on the relative distance measure (RDM) arithmetic. In the proposed model, measurement errors are assumed to be bounded in given sets and the state variables are described as RDM variables. Since the SE model is a non-convex, the solution's credibility cannot be guaranteed. Therefore, each nonlinear measurement equation in the model is transformed into dual inequality linear equations using the mean value theorem. The SE model is finally reformulated as a linear programming contractor that iteratively narrows the upper and lower bounds of the estimated state variables. Numerical tests on IEEE three-phase distribution networks show that the proposed method outperforms the conventional interval-constrained propagation, modified Krawczyk-operator and optimization based interval SE methods. [ABSTRACT FROM AUTHOR]

The primary methods of assessing the reliability of distribution networks comprise analytic and simulation methods. However, both approaches require the identification and computation of network topology, which precludes their expression in explicit, continuous functions, consequently impeding the incorporation of reliability constraints into planning and operational optimization models. To tackle this restriction, the present work puts forth a novel linear‐programming‐based reliability assessment method that is mathematically formulated, considering distribution automation (DA) and distributed generations (DGs), consisting of both conventional and renewable energy sources. In this paper, the clustering method and the scenario‐based method are used to model DGs. Next, a mixed integer linear programming (MILP) model, considering the DA and DGs with the System Average Interruption Duration Index (SAIDI) as the optimization objective, is proposed. Finally, the feasibility and effectiveness of the proposed method are verified in a 37‐node distribution network system. [ABSTRACT FROM AUTHOR]

Electric vehicles (EVs) are rapidly replacing conventional fuel vehicles, offering powerful, emission-free performance. This paper introduces an innovative three-phase bidirectional charger for grid-to-vehicle (G2V) and vehicle-to-grid (V2G) applications, strengthening the connection between EVs and the power grid. The charger employs a two-stage power conversion approach with advanced converters and a simplified dq-based charging control strategy. An efficient AC-DC converter facilitates smooth transitions between modes, responding to grid directives for active and reactive power. A soft-switching dual active bridge (SS-DAB) DC-DC converter optimally interfaces with the EV battery pack, while dual active LCL filters suppress harmonics, enhancing system performance. Simulated results confirm the charger's effectiveness in a 3.5-kW prototype using MATLAB/Simulink. The proposed SS-DAB converter-based bidirectional on-board charger introduces a groundbreaking unified Voltage Source Converter (VSC) control approach, enabling efficient power transfer in both vehicle-to-grid (V2G) and grid-to-vehicle (G2V) modes. This innovation ensures rapid dynamic response, exceptional steady-state performance, and robustness against grid demand changes, optimizing EV integration. [ABSTRACT FROM AUTHOR]

Considering the importance of the renewable energy sector in the distribution systems, energy operation, and management which are connected to the distribution network (DN) in the form of multiple microgrids (MMGs) is crucial in reducing cost and pollution. Hence, this paper aims to propose optimal energy management for MMGs in the DN. Different objective functions have been taken into account in this optimization, including network cost, pollution reduction, and distribution network power losses. To design the multi‐objective optimization problem, a fuzzy method has been adopted for simultaneous multi‐objective calculations. Furthermore, the effect of the placement of distributed generations (DGs) and microgrids (MGs) is considered to reduce the distribution network power losses. Information gap decision theory (IGDT) has formulated uncertainties about renewable sources and consumers. To solve this optimization problem, a new method of the modified Harris Hawk optimization (MHHO) algorithm has been implemented, compared with the original HHO and genetic algorithm (GA). Finally, the proposed method has been analysed under the IEEE 33‐bus distribution network for a 24‐hour time horizon, including three MGs considering different renewable energy sources (RESs). The simulation results have demonstrated the high performance of the allocated network with the MHHO algorithm compared to the other scenarios. [ABSTRACT FROM AUTHOR]

This paper proposes three‐phase steady‐state models for distributed generators (DGs) with different negative control strategies. An augmented rectangular load flow method is used for three‐phase distribution systems. For two types of DGs with power electronic devices: photovoltaic power generators and doubly fed induction generators, the nodal voltage equations and output power equations are derived. Moreover, under unbalanced conditions, the strategies for mitigating the effects caused by negative sequence components are formulated as functions of the nodal voltage and the injected current. Furthermore, the models are incorporated into an augmented rectangular load flow method with nodal voltage and injected current as state variables in three‐phase systems. Case studies are conducted to verify the correctness and accuracy of the proposed models by comparing the results obtained from MATLAB and PSCAD. [ABSTRACT FROM AUTHOR]

As the penetration of renewable distributed generation (RDG) continues to grow, the stochastic and intermittent nature of its output imposes significant challenges on distribution networks (DNs), such as source-load mismatch and voltage fluctuations, which seriously affects the safety and reliability of the system. Thus, this paper presents a stochastic optimal allocation method for a battery energy storage system (BESS) in the DN, with the consideration of annual load growth, BESS degradation, and DN operation, aiming to minimize the overall cost of DNs and harvest more renewable energy. Based on the rainflow-counting concept, BESS degradation is efficiently modeled and linearized to improve solvability. Additionally, to address the uncertainties of RDG outputs and loads, a stochastic optimization (SO) method is adopted. Furthermore, considering that a large number of integer variables of the BESS allocation model may cause a heavy computational burden, a feasibility pump-based solution algorithm is introduced to accelerate the solving speed. Finally, the effectiveness of the proposed BESS allocation method and the solution algorithm is verified on a 33-bus DN system through comparative analyses, showing high efficiency and performance. [ABSTRACT FROM AUTHOR]

In recent times, a significant amount of power loss and system instability due to high voltage deviation experienced by modern power systems, in addition to the pressing issues challenging the power industry such as pollution—especially the emission of greenhouse gases—and aging infrastructures, have posed a serious threat to system operations. Distributed generation has been identified as one main solution capable of reducing pollution when solar and wind power are used and, hence, rejuvenating dilapidated infrastructures and redeeming climatic changes. This paper presents a novel two-stage approach for the identification of suitable locations for DG placement and the sizing of DG for loss reduction and voltage stability enhancement. The first stage explored the use of a network structure to develop a coupling factor (CF) approach that was non-iterative in nature to determine suitable DG locations. In the second stage, the size of the DG was determined using the particle swarm optimization (PSO) algorithm. The main objective was to obtain an optimal voltage profile of the system under consideration while lowering the power loss in the system and ensuring network stability amidst DG incorporation. The model design, optimization and simulation were carried out using the MATLAB 2016a environment and the IEEE 33-bus test system, in which DG was integrated. The influence of increasing the level of DG placement in the system was then investigated. The forward/backward sweep method was applied to monitor the optimization process. The voltage profiles for both the base case when no DG was integrated and the case of incremental DG integration were considered. The results obtained for both single and multiple DG integration are compared with those obtained using the existing methods. The results show the efficiency and applicability of the new non-iterative scheme in the quick identification of DG locations for voltage profile enhancement and network real power loss reduction in radial distribution networks. [ABSTRACT FROM AUTHOR]

The efficient, reliable, and resilient supply of electricity has become essential for social and economic well‐being of the modern society. However, more frequent occurrence of extreme weather events has exposed inequity in the planning and operation practices of power distribution systems, evidenced in higher vulnerability and longer power interruptions for some parts of the grid as compared to others. This paper proposes an equity‐aware power distribution system restoration model in an effort to ensure a more equitable yet resilient power distribution operation after outages. To this end, the proposed equity‐aware distribution system restoration model balances the efficiency of the restoration operation and the equitable allocation of distributed energy resources among affected customers after an outage, while prioritizing the critical infrastructure (e.g. hospitals). The results demonstrate the effectiveness of the proposed framework to ensure a more equitable restoration process as measured by the proposed fairness and restoration performance indices. [ABSTRACT FROM AUTHOR]

Distributed energy resources (DERs) provide flexible load restoration strategies, which can effectively enhance the resilience of active distribution systems (ADSs). Whereas, the widespread DERs in ADSs complicates the supply‐demand relationship and make the system resilience difficult to access. Therefore, this paper proposes a simulation‐based resilience assessment algorithm of ADSs considering the microgrid formation based on grid‐edge DERs. Microgrid formation is used to depict the resilience gain of grid‐edge DERs on ADSs. Specifically, a resilience assessment framework for ADSs is firstly proposed, where the uncertainty of component state and supply‐demand is modelled based on probability statistics. Then the mixed integer linear programming is used to search for optimal load restoration strategies with microgrid formation. On this basis, a set of resilience indices are defined to quantitatively analyse the resilience of ADSs, and a resilience assessment algorithm with uncertainty scenario generation is proposed to obtain these indices. Furthermore, extensive numerical results based on a modified IEEE 123‐bus feeder validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In the context of rare but high‐impact extreme scenarios, such as natural disasters, it is crucial to utilize all available resources, including microgrids and distributed power sources, to restore critical loads in the distribution network as much as possible. This paper proposes a two‐stage resilience enhancement strategy for distribution networks considering post‐disaster topology reconstruction and demand response, aiming to facilitate the recovery of critical loads after disasters. In the first stage, a heuristic algorithm is introduced to determine the post‐disaster topology of the distribution network. In the second stage, by employing a step‐wise elastic load curve, user demand response is incorporated to maximize the socio‐economic value of the restoration, and resilience metrics are computed. Finally, the effectiveness of the proposed resilience restoration strategy is validated through simulations on Case33 and Case69 systems. [ABSTRACT FROM AUTHOR]

This paper introduces a comprehensive performance evaluation algorithm explicitly designed for secondary equipment in substations, specifically targeting the relay protection system. In contrast to the current evaluation systems, this novel method navigates the complex internal interconnections and mechanisms inherent within secondary system equipment. Such complications have previously impeded the accuracy and breadth of evaluations, thereby limiting the degree of precision and innovation attainable within substations. The proposed approach effectively integrates the improved Analytic Hierarchy Process entropy weight (IAHP‐EW) method with the Learning Vector Quantization (LVQ) neural network. Initially, the IAHP‐EW method identified the comprehensive evaluation indicators and their corresponding weights for relay protection devices. Following weight allocation, these evaluation indicators are scrutinized and computed utilizing the multivariate regression analysis algorithm, resulting in performance evaluation outcomes for the relay protection system. These outcomes are subsequently classified and utilized in training the LVQ neural network, promoting the network's capacity to autonomously evaluate the performance status of the relay protection system. To corroborate the viability and effectiveness of this proposed performance evaluation and prediction algorithm, empirical operating data from a local substation is used. The results suggest a significant improvement in the evaluation accuracy of secondary equipment performance, indicating potential for practical application and a valuable contribution to the field through the introduction of a novel approach to performance assessment of substation relay protection systems. [ABSTRACT FROM AUTHOR]

In the case of a single‐phase grounding fault in the distribution network, the transient zero‐sequence current (TZSC) tends to be non‐linear and non‐stationary. The faulty line selection is relatively difficult. The distributed power access further brings many difficulties to faulty line selection. This work proposes a novel method of faulty line selection using spatial image generation and deep learning. At first, the optimal smooth denoising model can be used to smooth the zero‐sequence current for each line, reducing the external environment electromagnetic interference. Then, the treated zero‐sequence current is mapped into the colorful floral hoop image by using symmetrized Hilbert transform pattern (SHTP). The SHTP transforms the one‐dimensional time domain signal into the two‐dimensional space domain image, enhancing invisible information and obtaining more abundant feature information. Finally, the deep features of the SHTP floral hoop image are extracted by means of deep learning method. In order to improve the faulty line selection universality, a mixed sample library containing three different topologies is established, including the 10 kV radial distribution network, IEEE‐13 node model, IEEE‐34 node model and StarSim platform. The comparisons show that the proposed method has a more noticeable visualization effect on fault features, higher classification precision rate, and better anti‐noise performance. [ABSTRACT FROM AUTHOR]

This paper presents a multi‐objective restoration scheme for improving the resilience of integrated electricity and natural gas distribution systems against extreme weather events. The coupling constraints of electricity and gas networks are tackled properly using a linearized optimal power flow (OPF). Distributed generators, power‐to‐gas facility, rescheduling of generation/storage units, and microgrid formation are employed as operational resources/measures for restoring the integrated energy system after the event landfall. An adaptable directed multi‐commodity flow‐based microgrid formation is utilized, that is, the network configuration is dynamically changed in accordance with time‐variant load priority weights. The proposed method was successfully examined on an integrated electricity and natural gas distribution system comprised of the modified IEEE 33‐bus distribution network and a 14‐node natural gas distribution network. Numerical results showed that using microgrid formation increased the supplied critical load of integrated electricity and natural gas distribution system by about 16%. Moreover, due to making benefit of the power‐to‐gas unit, the supplied critical load increased by about 12.3%. respectively. While utilizing energy storage systems along with the power‐to‐gas unit facilitated the exchange of energy between the power distribution network and natural gas distribution network regarding time‐variant load priority weights, the supplied critical load increased by about 13%. [ABSTRACT FROM AUTHOR]

With the increasing rate of population in big cities around the world, the tendency to build new buildings in the suburb of main cities or to build large apartments in the main cities has been highlighted. In this regard, building residential complexes has seen a dramatic increase in these areas as it makes it possible to build a large number of residential units within a reasonable space. Although these complexes have brought numerous benefits, they are some challenges regarding their construction processes. One main concern associated with these complexes is how to optimally install energy components such as transformers, combined heat and power (CHP) units, boilers etc., in the shared area of apartments in the residential complex. To address this issue, this paper models the energy system of a residential complex as an energy hub and proposes a novel framework to obtain the optimal planning of such an energy hub. In order to address the conflicting desires of the residential complex's builders and the future residents of the residential units, a multi‐objective (MO) optimization problem has been considered in the proposed method that simultaneously optimizes the investment costs, operation costs, and the reliability of energy supply. In this regard, a Multi‐objective Particle Swarm Optimization (MOPSO) algorithm combined with classical linear programming (LP) optimization method has been proposed to solve the MO optimization problem. In order to demonstrate the effectiveness of the proposed method, a case study including a residential complex with 300 residential units is considered, and the proposed method is implemented in this case study. The numerical results show that the proposed framework can appropriately optimize investment costs, operation costs, and the reliability index simultaneously, and the obtained Pareto frontier gives the investors the freedom to opt for any point from this surface. [ABSTRACT FROM AUTHOR]

This paper extends the study of a zero‐sequence impedance‐based fault location method (FLM) designed for medium voltage (MV) distribution feeders whose principle has been presented in a previous work Bach et al. This method is able to locate any type of earth fault with any type of neutral grounding inside a convex set of nodes forming the solution area. The total length of the lines inside this area is statistically computable a priori and depends only on the number and location of additional voltage measurements deployed on some remote end secondary substations. To be efficiently applied to the most challenging rural feeders presenting a lot of ramifications, simulations have shown a need for synchronized measurements, such as the ones obtained using phasor measurement units. Besides, this paper addresses the coupling potential of this method with more traditional ones such as Takagi‐based FLMs to enhance the performances of both, solving the multiple estimation problem while potentially locating the fault within one node. Finally, an extensive sensitivity analysis has been carried out, showing a good robustness with respect to impedance estimation errors or fault impedance values while showing the need for synchronization, especially on some remote measurement locations. [ABSTRACT FROM AUTHOR]

The increasing penetration of distributed renewable energy sources drastically alters the dynamic characteristics of distribution networks (DNs). Therefore, several equivalent models have been recently proposed, to analyze more accurately the complex behavior of modern DNs. However, relatively simple models are still commonly used in practice for dynamic power system studies. In addition, dynamic equivalent models for DNs are sensitive to different operating conditions and there is lack of systematic understanding of their performance. Scope of this paper is to propose a methodology for identifying the applicability range in terms of accuracy and generalization capability of several conventional and newly developed equivalent models for the dynamic analysis of modern DNs. A set of metrics is used for the modelling accuracy assessment and a sensitivity analysis framework is introduced to fully quantify the generalization capabilities of DN equivalent models. Based on the above, guidelines and recommendations for the development of robust equivalent models for DN analysis are proposed. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

Microgrids are a new concept resulting from decentralized power sources, which have changed energy utility grid topography. As this promising field is penetrated, control must be streamlined immediately. This paper analyses key control mechanisms in energy utility networks, including centralized, decentralized, and distributed setups. The focus is on the auxiliary category as the various benefits and drawbacks of each approach is investigated. Information interchange architectures that enable multiple control techniques in the auxiliary control domain are examined using distributed energy networks. The research emphasizes the necessity of auxiliary control in ensuring reliable and effective utility infrastructure operation but notes the lack of a comprehensive scholarly reference. Additionally, the study explores key concerns in utility grids' auxiliary control mechanisms, emphasizing information‐sharing system limits. The goal is to demonstrate the importance of auxiliary control and evaluate its challenges, such as latency, which require new solutions for a seamless transition to a sustainable energy future through rigorous academic assessment. At the auxiliary level, complex, decentralized regulatory mechanisms are recommended to handle transmission channel bandwidth and operational overhead in energy utility networks. These innovative measures have the potential to transform the fundamental structure of our energy landscape, heralding in unprecedented efficiency and sustainability. [ABSTRACT FROM AUTHOR]

Precise energy management in distribution power system requires high‐precision time synchronization among large‐scale deployed devices. Multiple clock sources‐based time synchronization possesses advantages of reliability, high precision, and robustness, but still faces several challenges such as coupling between time synchronization error and delay, as well as different timescales between clock source and clock weight optimization. In this paper, a multi‐clock source time synchronization model is constructed and a problem is formulated to minimize the synchronization error and delay through jointly optimizing large‐timescale clock source selection and small‐timescale weight selection. A reinforcement learning‐based multi‐timescale multi‐clock source time synchronization algorithm named RL‐M2 is proposed to solve the formulated problem from a learning perspective. Besides, a lossless switching method is proposed to address the switching problem for multiple clock sources. Simulation results demonstrate the superior performance of RL‐M2 and the lossless switching method in time synchronization delay and error. [ABSTRACT FROM AUTHOR]

This paper presents an optimal allocation methodology of photovoltaic distributed generations (PVDGs) with Volt/Var control based on Automatic Voltage Regulations (AVRs) in active distribution networks considering the non-dispatchable mode of PVDG operation. In the proposed methodology, an intelligent coordinated Var control is activated via controlling the AVR tap position and the Var injection of PV inverters to achieve a compromise between reducing active and reactive power losses and enhancing voltage quality in a distribution network. Also, the scheduled power factor mode of operation is investigated for the PV inverters. Added to that, the proposed allocation methodology is handled on the basis of hourly loading variation under simultaneous control modes of PV inverters and AVR. Moreover, the impacts of the specified number of PVDGs are assessed on the distribution system's performance. A recent effective optimizer of the slim mold algorithm (SMA) is dedicated to solving the proposed optimization framework. The simulation implementations are executed on a practical distribution network of the Kafr Rabea area related to South Delta Electricity Company in Egypt. Also, the application is conducted for a large-scale distribution network from the metropolitan area of Caracas. The proposed methodology provides superior performance in minimizing the active and reactive power losses and improving the voltage profile. [ABSTRACT FROM AUTHOR]

Modern fault ride-through (FRT) standards in many countries require distributed generators to remain connected for a specified period during the fault by providing reactive current, to support voltage and prevent a massive renewable outage. As a result, short-circuit current is not constant, but it varies depending on the current and disconnection order of distributed generators (DGs). This time-varying short-circuit current complicates the estimation of the time it will take for an overcurrent relay or fuse to trip. The existing short-circuit calculation algorithms usually assume that the fault current is constant throughout the whole period of fault. This assumption may result in incorrect conclusions regarding the tripping time of protective devices in networks with high renewable penetration. This paper incorporates modern FRT standards into the fault analysis by considering the influence of fault current variations on the protective devices (relays, fuses), significantly increasing the accuracy of the estimated tripping time. Simulations carried out in a 13-bus and the IEEE 8500-node network indicate that the traditional short-circuit calculation approaches may miscalculate the tripping time of protective devices, with deviations up to 80 s, when applied to networks complying with modern FRT standards. [ABSTRACT FROM AUTHOR]

Nontechnical losses of electrical energy (NTLEE) have been a persistent issue in both the Russian and global electric power industries since the end of the 20th century. Every year, these losses result in tens of billions of dollars in damages. Promptly identifying unscrupulous consumers can prevent the onset of NTLEE sources, substantially reduce the amount of NTLEE and economic damages to network grids, and generally improve the economic climate. The contemporary advancements in machine learning and artificial intelligence facilitate the identification of NTLEE sources through anomaly detection in energy consumption data. This article aims to analyze the current efficacy of computational methods in locating, detecting, and identifying nontechnical losses and their origins, highlighting the application of neural network technologies. Our research indicates that nearly half of the recent studies on identifying NTLEE sources (41%) employ neural networks. The most utilized tools are convolutional networks and autoencoders, the latter being recognized for their high-speed performance. This paper discusses the main metrics and criteria for assessing the effectiveness of NTLEE identification utilized in training and testing phases. Additionally, it explores the sources of initial data, their composition, and their impact on the outcomes of various algorithms. [ABSTRACT FROM AUTHOR]

This paper presents a reliability evaluation method for distribution network with distributed generations considering feeder fault recovery and network reconfiguration, and mainly addresses issues: 1) insufficient consideration of the characteristics for the components and distributed generations (DGs) of distribution network such as time sequences, randomness and intermittency; 2) changes in the feeder area of the distribution network after the access of DGs; and 3) multi‐dimensional reliability index for distribution network with DGs has not been formed perfectly. Firstly, Markov reliability model for distribution network components/DGs is established in our study. Then, considering the fault recovery and network reconfiguration of the feeder area, island partitioning method of distribution network with DGs is also proposed. Moreover, a reliability evaluation model is presented for distribution network with DGs based on sequential Monte Carlo method. Case study is performed on the improved IEEE RBTS BUS6 F4 feeder system, and the research results indicate the validity and effectiveness of the proposed method. In addition, the system reliability indicators, such as system average interruption frequency index (SAIFI), system average interruption duration index (SAIDI), customer average interruption duration index (CAIDI), and average system availability index (ASAI), are studied and discussed in detail from three dimensions: the access of DGs, the types of DGs, and the capacity of DGs. [ABSTRACT FROM AUTHOR]

Nowadays, due to network expansions, system operators are dealing with natural events including system failures. Evaluating the system readiness to maintain the network interconnections during severe faults are known as an important challenge of today's distribution networks. To do this, this paper presents an online non‐model‐based scheme of evaluating the system resiliency and supplying critical loads within severe natural conditions. In this case, by developing system resiliency as multi‐metric decision making problem and proposing the Choquet integral and graph theoretic methodology, the system resiliency is evaluated. The proposed resiliency scheme is an online non‐model‐based approach can be used for all distribution system configurations with the potential of natural event failures. In this case, by proposing online resiliency criteria based on the system critical loads and branches and developing the proposed criteria on Choquet integral scheme in the form of optimization procedure, the system resiliency is evaluated. The validity of the proposed approach is carried out on two different systems including the IEEE 123‐bus test system and the Consortium for Electric Reliability Technology Solutions (CERTS) microgrid. Simulation results present effectiveness of the proposed scheme to provide proper protective switching strategy and design the system resiliency criteria for future distribution systems. [ABSTRACT FROM AUTHOR]

This paper proposes a mixed‐integer non‐linear programming (MINLP) model for the multi‐period active low voltage (LV) distribution network expansion planning problem, which can be solved by off‐the‐shelf optimization solvers. In addition, the wide‐spread penetration of solar resources, optimal loading of transformers, and modeling of the multiple solar generation patterns are considered in the model. The solar resources are of roof‐top household‐scale photovoltaic panel type, developed using a host‐owned business model and are able to exchange energy with the distribution company (DISCO). This model enables the DISCO, as the owner of the network, to minimize the investment and operation costs while being able to determine the optimal location and capacity of the distribution transformers, the service zone of distribution transformers, the optimal route of the distribution lines, and the total and annual planning costs. In order to check the efficiency of the proposed model, a 0.4 kV distribution test network is considered to plan the LV network of a residential district over a planning horizon of 5 years. Results show the effectiveness of the proposed model in dynamic expansion planning of the active LV distribution network. Also, results illustrates that the penetration of solar sources can be a great tool to improve the technical, economic, and environmental criteria for planning studies. Specifically while reducing the billing costs of customers, it favors the government to reduce the pollution costs, and it enables the DISCO to reduce the loss costs and maintain the voltage in the standard boundaries. [ABSTRACT FROM AUTHOR]

The structure complexity and the extended geographical area are among the factors that create challenges in accurate fault location and detection in distribution networks. The single‐phase to ground (SPG) faults are considered as most frequent reasons for distribution network interruption, which can threaten the network's reliability. Signal processing methods are usually used as common approaches to distinguish and locate faults in distribution networks. This paper proposes a novel scenario to select optimal wavelet packet transform (WPT) coefficients for SPG fault location and a method based on superimposed voltage energy to distinguish the faulty phase according to these coefficients. Furthermore, employing the energies of the superimposed voltages helps to minimize the effects of high resistance faults (HRFs) and load encroachment on the efficiency of the faulty phase detection part. Comparing the obtained results with other scenarios demonstrates the considerable efficiency of the proposed scenario. Finally, with the help of general regression neural networks (GRNN) as machine‐learning tools, a new algorithm is derived for detecting and locating the SPG fault and capacitor bank switching overvoltage (COV). Simulation results are implemented on the IEEE 34‐bus standard distribution network, demonstrating the efficiency and superiority of the suggested method. [ABSTRACT FROM AUTHOR]

The increasing use of non‐linear loads in electrical distribution systems (EDS) led to a greater need for reactive power compensation, losses minimization, improved voltage and stability. This paper proposes the optimal integration of hybrid photovoltaic distributed generation (PVDG) and distribution static synchronous compensator (DSTATCOM) into IEEE 33 and 69‐bus EDS. A modified version of homonuclear molecules optimization (mHMO) is developed to determine the optimal allocation of the devices, while minimizing a multi‐objective function (MOF) based on total active power losses (TAPL), total voltage deviation (TVD), and investment cost of integrated devices (ICPVDG and ICDSTATCOM). The primary objective of the mHMO is to enhance the equilibrium between exploration and exploitation in the original HMO by implementing a fresh exploration stage. The effectiveness of mHMO was assessed using CEC17 benchmark functions. The findings demonstrate that mHMO achieved excellent results, including high‐quality solution and a favourable convergence rate. Additionally, results demonstrate that mHMO outperforms its basic version in reducing TAPL by 94.27% and 97.87% for the two EDS, while improving voltage profiles and reducing the cost of integrated devices. This study shows the potential of hybrid PVDG‐DSTATCOM in improving the performance of EDS and highlights the effectiveness of mHMO in optimizing their integration. [ABSTRACT FROM AUTHOR]