Search

With the rapidly growing interest in using structural timber, a need exists to inspect and assess these structures using non-destructive testing (NDT). This review article summarizes NDT methods for wood inspection. After an overview of the most important NDT methods currently used, a detailed review of Ground Penetrating Radar (GPR) and Ultrasonic Testing (UST) is presented. These two techniques can be applied in situ and produce useful visual representations for quantitative assessments and damage detection. With its commercial availability and portability, GPR can help rapidly identify critical features such as moisture, voids, and metal connectors in wood structures. UST, which effectively detects deep cracks, delaminations, and variations in ultrasonic wave velocity related to moisture content, complements GPR's capabilities. The non-destructive nature of both techniques preserves the structural integrity of timber, enabling thorough assessments without compromising integrity and durability. Techniques such as the Synthetic Aperture Focusing Technique (SAFT) and Total Focusing Method (TFM) allow for reconstructing images that an inspector can readily interpret for quantitative assessment. The development of new sensors, instruments, and analysis techniques has continued to improve the application of GPR and UST on wood. However, due to the hon-homogeneous anisotropic properties of this complex material, challenges remain to quantify defects and characterize inclusions reliably and accurately. By integrating advanced imaging algorithms that consider the material's complex properties, combining measurements with simulations, and employing machine learning techniques, the implementation and application of GPR and UST imaging and damage detection for wood structures can be further advanced. [ABSTRACT FROM AUTHOR]

Experimental tests of cross-laminated timber (CLT)-concrete composite floor panels were conducted. The tests consisted of linear-elastic tests of square CLT-concrete composite panels with a novel shear connector to determine elastic orthotropic plate properties. After the linear-elastic tests, the panels were subjected to a patch load at the center of the panel and tested to failure. To investigate load transfer across longitudinal joints between adjacent panels, nonuniform bending tests were conducted. Results from the experimentally measured orthotropic plate properties showed that the shear connector increased the bending stiffness in the weak direction of the panel compared to prior test results using conventional shear connectors. The tests to failure exhibited larger differences in behavior between the strong and weak orientations of the specimens, with both showing substantial inelastic behavior prior to failure. Numerical finite element models of the patch-load test showed good agreement with experimental results. Analytical formulas using the obtained orthotropic plate properties did not agree with experimental results for the patch-load at linear scales, suggesting the simplified method is currently not suited for CLT-concrete two-way bending. Load-transfer tests found that the reinforced concrete topping is capable of transferring load across the longitudinal joint of two parallel panels to enable two-way bending of composite timber–concrete floors and that the addition of a plywood spline with closely spaced screws enables a higher degree of force transfer. [ABSTRACT FROM AUTHOR]

The main objective of this work is to characterize the stress–strain relationship of cross-laminated timber (CLT) wall panels when loaded in compression and how different confinement mechanisms provide compression reinforcement for the CLT panels. CLT crushing tests were performed to define the behavior of CLT under compression up to the failure point, defined here as the strain at which the gross stress falls by 20% from the peak value. Testing included monotonic uniform compression experiments of five-ply CLT with specimens that were 0.457 m wide by 1.52 m long. The motion of the specimens perpendicular to loading direction was restrained at midlength to prevent buckling. Twelve specimens were tested, including six bare CLT specimens and six reinforced specimens of CLT—three with self-tapping screws while the other three with self-tapping screws and an additional U-shape steel plate at the bottom of the specimens. Various damage points were observed during the tests, including (1) point at the onset of damage (through visual observation and instrumental observation) (2) point of initiation of strength degradation, (3) point at which buckling occurs, (4) point at which 25.4 mm delamination was observed, and (5) failure point. Three axial compression stress–strain models were adopted, calibrated, and compared. Results indicate that a stress–strain model combining linear and cubic functions for the elastic and softening responses, respectively, captures well the CLT inelastic behavior under compression. [ABSTRACT FROM AUTHOR]

While the use of cross-laminated timber (CLT) panels for building construction has increased over the last several decades, current standards and existing literature provide limited information regarding the design of CLT diaphragms or the prediction of their deflections when subjected to wind and strong earthquake motions. This paper presents the design and assessment of a CLT diaphragm that was part of a full-scale two-story structure subjected to shake-table testing. An analytical model is proposed for diaphragm deflection accounting for in-plane shear and bending stiffness, as well as the stiffness of various connections. Moreover, a refined numerical modeling strategy is proposed in order to consider phenomena such as panel-to-panel gap closure. Results indicate that the analytical model yields conservative results both in terms of deflections and forces when compared to the numerical model that simulates similar sources of strength and stiffness. The analytical model is suitable for the design of symmetric diaphragms with regular shapes, whereas the numerical model can also be used to model asymmetric diaphragms with irregular shapes. [ABSTRACT FROM AUTHOR]

Mass timber construction has seen a growing interest in North America and worldwide. In the US, code provisions allow mass timber buildings to be up to 82 m tall, but with floor slabs requiring a noncombustible, usually cementitious, topping over mass timber panels (MTPs). Designing the MTP and concrete topping to act compositely can increase the strength and stiffness compared to noncomposite MTP floors. Several connections are available to create composite action between an MTP and a concrete topping, with self-tapping screws being the most widely considered practice. A new test fixture and testing method were developed to characterize connection properties and facilitate the selection of fasteners most suitable for developing composite action. Three conventional self-tapping screws were experimentally investigated at the single-fastener scale. The screws were subjected to withdrawal at 90° and 45° orientations to the interface plane between the MTP and concrete. Withdrawal from both the MTP substrate and concrete topping was investigated. Three MTP materials were tested: cross-laminated timber (CLT) consisting of two different wood species and a mass ply panel (MPP). Results demonstrated that the pullout failure of the screwhead from the concrete was the limiting failure mode. Comparisons were made between the experimental results and analytical models for screw withdrawal to assess the applicability of available models to the different MTPs. These models underestimated the capacity of the tested fasteners for all samples except for the fully threaded screws. [ABSTRACT FROM AUTHOR]

Timber–concrete composite (TCC) floors exposed to fire experience charring and thermal degradation of timber, leading to a reduction in load-carrying capacity. Finite element (FE) modeling supplements data from experimental fire testing and allows for fast and economical investigation of additional design parameters. This research presents fire test results of three large-scale TCC floor specimens and development of an FE modeling methodology for TCC floors in a fire. TCC floors constructed with nail-laminated timber, cross-laminated timber, or mass ply panel, with truss plates or angled screws as shear connectors, are loaded with a uniformly distributed service-level live load and exposed to the ASTM E119-20 standard fire curve. A 2D FE modeling methodology is presented and benchmarked against the test data. The methodology integrates sequentially coupled thermal-structural analyses, which make use of temperature-dependent thermal and mechanical properties of timber and concrete. The deflection and failure times of the FE models are benchmarked against test data. Connector forces from FE models show that shear connectors remain elastic throughout the fire exposure. FE results indicate that the load-carrying capacity is dependent on tensile stress redistribution to the uncharred timber section. The FE modeling methodology effectively calculates the mechanical and fire behavior of TCC floors and highlights limits of the applicability of analytical design methods. [ABSTRACT FROM AUTHOR]

Background: Humans are accidental hosts in the zoonotic disease Scrub typhus. The disease though widespread in our county, it remains grossly underdiagnosed because of its non-septic clinical manifestations and lack of access to specific laboratory facilities. Aims and Objectives: The objective of present study is to evaluate the clinical presentations of Scrub Typhus among the study group. Furthermore, to assess the various laboratory findings in Scrub Typhus cases among the study group is the other objective of this study. Materials and Methods: The present study is an Institution-based, observational, and cross-sectional study conducted for 18 months with the admitted patients having 14-70 years of age. Data collected regarding patients' demographic profile, symptoms, clinical findings, laboratory, and radiological findings. Data had been summarized as mean and standard deviation for numerical variables and count and percentages for categorical variables. Results: In our study, we found that most of the patients were 14-20 years old and female population was higher. It was found that 34.3% of patients had Eschar, 42.9% of patients had Rash, and 91.4% of patients had Pallor, 8.6% of patients had Ascites, 25.7% had Edema, 8.6% of patients had Jaundice, 11.4% had shock, and 57.1% had pneumonia/pneumonitis. The present study showed that 65.7% of patients had drug response (Doxycycline). Conclusion: Knowledge of geographical distribution, evidence of exposure to vector, clinical features such as fever, rash, eschar, headache, and myalgia along with high index of suspicion are crucial factors for early diagnosis and that helps in timely treatment of the cases. [ABSTRACT FROM AUTHOR]

Limited research exists on the deformation compatibility behavior of mass timber beam-to-column connections. Therefore, to investigate this behavior, large-scale experimental monotonic testing was performed on five different glue-laminated (glulam) beam-to-column connections. The purpose of this research was to create a better fundamental understanding of the deformation compatibility behavior of mass timber beam-to-column connections. Three connections were custom-designed connections, and two were pre-engineered connections. Specimens included the presence of cross-laminated timber (CLT) decking on the beam, as well as combined lateral and gravity loading. Monotonic tests pushed specimens to a target story drift of 7.2% at a rate of 0.51 mm/s. The data were analyzed, and the yield force, yield displacement, initial stiffness, secant stiffness, and connection classification (categorized as either rigid, semirigid, or flexible) were calculated for each connection. Per the connection classification methodology used, all connections were classified as flexible (simple) connections. However, the pre-engineered connections use substantially more screws and plates thereby increasing the cost and effort of installation. The results demonstrate that in some cases simple custom connections can have a larger yield force and initial stiffness than pre-engineered connections, and due to the reduction in number of screws, there was less damage within the connection at the completion of the test. The forces required to push connections to 2% drift all exceeded the lateral force capacity of the connections; however, all connections maintained load-carrying capacity throughout testing. [ABSTRACT FROM AUTHOR]

New building code changes enable mass timber panels (MTP), including cross-laminated timber (CLT), to be used in moderate and tall buildings as a floor system, usually with a concrete topping. A floor system of CLT composite with a reinforced concrete topping slab can provide increased stiffness and strength, making the system more advantageous. Present connection methods used to produce composite action within timber-concrete composites (TCC) have limitations when considering constructability or performance. This study presents experimental results from four (4) shear connectors for CLT-concrete composite floor systems, including three developed for this study. The connectors included self-tapping screws (STS) at 45-degrees, a modified lag screw with an integral plate washer that bears on the CLT surface at installation, a steel angle anchored only at the end of the span, and an inverted-T steel section with stem perforations. Different tests were performed on the different connectors including individual fastener tests, push-off group tests, and full-scale one-way bending tests. The push-off group tests showed that the proposed washer-screw exhibited higher stiffness and strength than a conventional STS. The full-scale one-way bending testing showed that the STS specimen exhibited the lowest strength of the alternatives. The inverted-T section exhibited the highest stiffness, while the other three connections had similar stiffness to the STS. [ABSTRACT FROM AUTHOR]

The deformation compatibility behavior of glue-laminated (glulam) beam-to-column connections is not yet well understood. To investigate this behavior, 10 specimens representing five different glulam beam-to-column connections were tested under lateral cyclic loading. Three of the connections were custom-designed connections and two were pre-engineered connections. Specimens were large-scale glulam beam-to-column connections, and testing included combined gravity and lateral loading as well as the presence of a cross-laminated timber (CLT) deck. Connection characteristics such as yield force, initial stiffness, secant stiffness, and energy dissipation were calculated and compared across connections as well as observations made during testing. Results from the experimental testing indicated that pre-engineered connections demonstrated overall better performance than the custom connections. Pre-engineered connections had the largest remaining secant stiffness by the end of the loading protocol, greater energy dissipation, and larger average yield forces than the custom connections. Although all connections tested exceeded their lateral design capacities at drift levels less than 2% drift, all connections maintained load-carrying capacity throughout testing. [ABSTRACT FROM AUTHOR]

Mass ply panel (MPP) is a new mass timber product that was recently introduced for structural applications in buildings. Although there have been several studies on characterizing the mechanical properties and structural performance of MPP, there is a lack of understanding regarding in-plane shear properties of the panels. More intensive studies should be done for MPP to provide a comprehensive understanding of its behavior. This paper presents an experimental study to characterize the effective in-plane shear modulus and shear strength of MPP in the major strength direction of the panel. Two experiments, including multiple span-length center-point bending tests and a novel large-scale shear test, were conducted. The test results were presented and compared with previous studies and the manufacturer's product report. The new test proposed for shear strength characterization has the potential to be an industry standard for mass timber panels. [ABSTRACT FROM AUTHOR]

The overall goal of this study is to gain an insight into the load sharing aspect between oriented strand board (OSB) and gypsum wall board (GWB) in shear wall assembly during racking load. Sixteen standard 2,440 x 2,440 mm walls were tested monotonically, in total, out of which 11 (Type A) were sheathed on both sides (OSB on one side and GWB on the other), while five walls were tested without GWB (Type B). Digital image correlation (DIC) was used for data acquisition and analysis which is a full-field, noncontact technique for measurement of displacements and strains. The system returns full-field three-dimensional displacement and strain data measured over the visible specimen surfaces. Overall, these tests suggest that initially during loading of a wall the load is shared between OSB and GWB. However, the proportion of load sharing is not known. As GWB fails first at about 60% of ultimate load capacity of the wall, the load shifts to the OSB panel which resists it until the failure of the wall. The tests also revealed that the load path in wall Types A and B is different and so is the failure pattern. Strains were locally concentrated around the fasteners, while the strains in the field of the panel were below the detection limit of DIC system. DOI: 10.1061/(ASCE)0733-9445(2009)135:6(666) CE Database subject headings: Shear walls; Wood structures; Frames; Strain distribution.

Over the past decade, cross-laminated timber (CLT) panels have gained popularity worldwide. To achieve larger spans and to increase the resistance to diaphragm seismic and wind forces to be transferred through CLT floor or roof systems, CLT-concrete composite (CCC) floors have been developed as an alternative. While significant testing has been performed under gravity loading, limited experimental data exist on the in-plane performance of CCC systems. This study presents results from an experimental program designed to characterize the in-plane shear behavior of CCC diaphragm connections using different CLT to concrete screw connector orientations in a test setup that simulates the expected seismic load path in diaphragms for platform-type construction. Tested variables include concrete slab thickness, composite screw angle, and single spline connection systems consisting of nails or screws. Experimental results and observed damage progression from cyclic testing are presented and discussed. Results indicate that CCC systems achieved increased stiffness and strength values when compared to bare-CLT systems, but slab thickness did not influence the strength and stiffness of the system for the load paths simulated. Additionally, CCC floor systems with 45° composite screw connectors displayed increased strength but overall similar stiffness values when compared to the CCC systems with 90° composite screws. The results provide useful engineering parameters, such as elastic stiffness, peak load, displacement capacity, and ductility ratios that can be used in the development of codified design parameters or in performance-based designs. [ABSTRACT FROM AUTHOR]

Mass plywood panel (MPP) is a veneer-based engineered wood product that recently was introduced in the mass-timber construction industry. Preliminary studies show that MPPs can be a preferred construction material for shear walls, floor diaphragms, and roof assemblies. However, no design guide exists regarding the use of MPPs as structural elements. This is compounded by a lack of engineering properties and parameters needed beyond the generic values provided in the product report. To assess the engineering properties and provide a benchmark dataset, a comprehensive experimental testing program characterized the performance of MPPs in flexure, in-plane shear (parallel to major strength direction), compression, and tension. Additionally, the characteristic values of MPPs were derived based on the test results to provide an initial indication of design values of MPPs. The test results presented in this study provide a fundamental basis for the development of a design guide for MPPs. [ABSTRACT FROM AUTHOR]

Cross-laminated timber (CLT) is an engineered wood product offering several advantages for wood utilization in midrise and tall buildings. However, moisture intrusion poses significant risks since it can affect the durability of CLT structural members and their connections. There has been much research on connection performance to understand their seismic response. However, the impact of moisture on the performance of CLT connectors is less understood. Cyclic tests were conducted on a series of CLT shear wall-to-diaphragm L-bracket (angle bracket) connections after subjecting them to a wetting and redrying cycle. The study includes three exposure durations and four wood species (Douglas fir, Southern yellow pine, Norway spruce, and spruce-pine-fir) to investigate the effect of moisture exposure on the connection performance. The performance was characterized in terms of strength, stiffness, and energy dissipation. In addition, two existing engineering force-displacement models were fitted to the experimental data. Results indicate that the changes due to wetting and redrying cycling were not statistically significant for the load-carrying capacity and stiffness. In contrast, a statistically significant decrease in the total energy dissipation capacity was observed. [ABSTRACT FROM AUTHOR]

A full-scale 2-story mass timber building was tested on the University of California San Diego Natural Hazards Engineering Research Infrastructure (UCSD-NHERI) uniaxial shake table during the period from June 2017 to September 2017. The main objective of the experimental program was to test the performance of mass timber building designs with different seismic lateral force–resisting systems. The focus of this study is on a building configuration designed using self-centering post-tensioned cross-laminated timber (CLT) rocking walls with U-shaped steel flexural plate energy dissipators. The shake-table tests were designed to subject the building to a series of earthquake ground motions of increasing intensity, ranging from a service-level earthquake to 1.20 times the maximum considered earthquake intensity. Between each ground motion, low-amplitude white-noise excitations were applied to the building, which responded as a quasilinear system. In this paper, two output-only operational modal analysis methods are used to estimate the modal parameters (frequency, damping, and mode shapes) based on acceleration data collected during the white-noise shake-table tests. The correlations of observed damage and repairs performed during the experimental program with changes in estimated modal features are reported. The modal parameters estimated from the testing program are also compared with a linear finite-element model that is used to validate the modal identification results and study the performance of the two system identification methods for CLT rocking structures. [ABSTRACT FROM AUTHOR]

This paper presents the behavior of floor diaphragms of a shake-table experiment of a full-scale 2-story mass-timber building structure. The structure consists of glued-laminated timber beams and columns, and floors and walls were designed and built making use of cross-laminated timber panels. Two different floor systems were designed, where the roof consists of a topped cross-laminated timber (CLT)-concrete composite system, and the floor level consists of untopped CLT panels connected with plywood single-surface splines. The CLT floor systems were designed to remain essentially elastic over the whole series of shake-table tests, which included testing of three lateral force–resisting systems tested at three different seismic intensity levels (service level, design basis, and maximum considered earthquake) for a total of 34 shake-table earthquake tests. Results from the testing indicate that CLT diaphragms designed to remain essentially elastic based on basic principles of structural mechanics and existing test data can achieve desired seismic performance objectives. In addition, sources of overstrength in certain elements of the diaphragm need to be explicitly considered for a holistic diaphragm design. [ABSTRACT FROM AUTHOR]

Timber-concrete composite (TCC) floors are becoming more commonly used in mass timber construction due to their increased stiffness and strength relative to nonconcrete composite timber floors. Current building codes do not recognize the contribution of the composite action of TCC floors to their combined strength and fire performance. Extensive structural testing is required for structural engineers to design fire protection in timber buildings that use TCC floors using either alternate means and methods or structural fire engineering. This paper presents two experimental studies conducted to examine (1) properties of shear connection systems used in TCC floors through ambient temperature direct shear tests, and (2) the behavior of TCC floors through large-scale fire tests performed at the National Research Council (NRC) in Canada. The main objective of this research is to collect data on the fundamental behavior of TCC floors in a fire. The results indicate that TCC floors have improved fire performance when compared with mass timber floors. In addition, the research quantifies the force-slip behavior of the shear connectors used and benchmarks the flexural behavior of TCC floors at ambient and elevated temperatures to existing analytical models. [ABSTRACT FROM AUTHOR]

Context: There is scarcity of data on thyroid function abnormality in COVID-19 patients in world literature. Aims: The objective of this study was to assess thyroid function tests in hospitalized patients of COVID-19. Settings and Design: Sixty (60) patients with COVID-19 detected by RT-PCR admitted in General Medicine isolation ward and COVID block of a tertiary care teaching hospital were selected by semi-purposive sampling. Materials and Methods: These patients were assessed for thyroid function tests, including total T3, free T3, total T4, free T4, TSH and anti-TPO antibody along with other baseline investigations. Patients with pre-existing thyroid–related ailments, those on levothyroxine or anti-thyroid drugs or other drugs known to interfere with the results were excluded. Results: There were 43.3% patients in mild, 26.7% in moderate, and 30% in severe category, according to local COVID-19 severity classification protocol. 35% patients had one or more abnormality in the thyroid function, low TSH being the most common (18.33%). 9.1% patients had characteristic pattern of thyroiditis. In most of the others thyroid function did not match any typical pattern. There was no significant difference in any of the parameters of the thyroid function test between mild, moderate, and severe groups. Conclusion: Thyroid function may be abnormal in all categories of patients during COVID-19 infection, even in absence of pre-existing thyroid ailments. Although low TSH is the commonest abnormality and typical pattern of thyroiditis can be seen in a subsection of patients, in majority of the patients, thyroid function abnormality does not follow any characteristic pattern and likely represents a combination of thyroiditis and sick euthyroid syndrome in different points of its spectrum. [ABSTRACT FROM AUTHOR]