Search

In this article, the C – V curve shift, trap densities responsiveness, and dynamic RON of AlGaN/GaN/GaN:C (SH:C) and AlGaN/GaN/graded-AlGaN:Si/GaN:C (DH:Si/C) heterostructure Schottky barrier diodes (SBDs) have been systematically analyzed. Due to additional 3-D electrons in graded-AlGaN:Si layer, the composite 2-D–3-D channel of DH:Si/C has a higher carrier concentration. Reducing the OFF-state electric field strength through AlGaN:Si insert layer, a smaller positive shift of C – V curve is achieved under OFF-state stress. Due to the charge shielding effect of AlGaN:Si insert layer, trapping/detrapping effects in GaN:C buffer under the OFF-state stress are well suppressed. Compared with SH:C heterostructure, the trap density responsiveness of DH:Si/C heterostructure under OFF-state stress is significantly reduced. At the same time, trap density responsiveness of the upper channel is immune to OFF-state electric stress time. In addition, the proposed SBDs show lower ON-resistance with on reverse bias stress and better dynamic performance with on reverse stress time. [ABSTRACT FROM AUTHOR]

In order to further improve the electrical characteristics of AlGaN-buffer devices, we propose a new in situ SiN/AlGaN-sandwich-barrier (SWB)/GaN/Al0.05GaN high-electron mobility transistors (HEMTs). The dc, channel temperature, and RF temperature of the proposed AlGaN-buffer devices have been systematically studied and analyzed. The SWB structure can effectively reduce the peak value of the electric field, thus effectively reducing the self-heating effect and improving the breakdown characteristics. Through the channel temperature extraction method of pulsed IV and TCAD thermal simulation, the channel temperature of devices with different barrier structures is compared and analyzed, which proves that SWB structure can effectively reduce the channel temperature of devices. Due to the more obvious potential modulation effect between gate and drain, the ƒmax of device can improve more effectively with the increase of drain voltage. In addition, load-pull measurement at 10 GHz revealed that a saturated power density increased from 7.3 to 8.4 W/mm and an associated PAE increased from 24.9% to 29.4%. [ABSTRACT FROM AUTHOR]

In this paper, AlGaN/GaN Fin-HEMTs with different fin configurations are theoretically and experimentally investigated. A simple physical-based threshold voltage model for AlGaN/GaN Fin-HEMTs is built for qualitative analysis. It is shown that the threshold voltage of AlGaN/GaN Fin-HEMTs depends on the width and height of the fin structure. The peak value and linearity of transconductance and current gain cutoff frequency are improved by reducing the fin length. It is also found that the linearity of transconductance is sensitive to the fin height, which can be attributed to the capacitance control from sidewalls. [ABSTRACT FROM AUTHOR]

A hybrid Schottky–ohmic drain technology for millimeter-wave (mmW) AlGaN/GaN high-electron-mobility transistors (HEMTs) is proposed. The Schottky metal extension in the ohmic region of drain reduces the actual source–drain spacing, resulting in a smaller ON-resistance and a higher maximum current. Extended Schottky metal in the drain region modulates the electric-field distribution, thereby leading to an improved breakdown voltage, suppressed current collapse, and high reliability. Compared with the ohmic drain, the current gain cutoff frequency (${f}_{T}$) was improved from 64 to 76 GHz, and the maximum oscillation frequency (${f}_{\text {max}}$) was improved from 125 to 157 GHz, resulting from the decreased parasitic drain resistance (${R}_{d}$). Moreover, large-signal measurements in continuous wave (CW) at 30 GHz demonstrated a peak power-added efficiency (PAE) of 45.5% and a saturated output power density (${P}_{\text {sat}}$) of 8.5 W/mm at ${V}_{\text {ds}}= {30}$ V. In addition, the direct current (DC) and radio frequency (RF) characteristics showed a negligible degradation after large-signal measurements at 30 GHz. [ABSTRACT FROM AUTHOR]

AlGaN/GaN high-electron-mobility transistors (HEMTs) with Si-rich SiN/Si3N4 bilayer passivation were studied in this article. The use of a Si-rich SiN interlayer leads to improved channel transport property, current collapse, power performance, and temperature-dependent stability. Devices without Si-rich SiN interlayer passivation exhibit an increase in the gate leakage current by over three orders of magnitudes with temperature increasing from 300 to 420 K, leading to an increase in a current collapse from 9.7% to 24.7%, while the devices with Si-rich SiN passivation exhibit a weak temperature dependence of leakage current and a constant current collapse about 5%. Small signal characterization shows that Si-rich SiN passivation results in a remarkable decrease in the effective gate length by ~15% with temperature up to 420 K. At 17 GHz, devices with Si-rich SiN interlayer passivation exhibit an output power density of 7 W/mm and a peak power-added efficiency (PAE) of 56%. The improved power performance of devices using Si-rich SiN interlayer passivation is attributed to the suppressed current collapse and superior device stability under high channel temperature. [ABSTRACT FROM AUTHOR]

The submicrometer gate HEMT is fabricated with an ultrathin-barrier (UTB) AlGaN/gallium nitride (GaN) combined with in situ SiN passivation. The sheet resistance of the UTB Al0.2Ga0.8N (4 nm)/GaN heterostructure is effectively reduced by the SiNx passivation layer grown by metal organic chemical vapor deposition (MOCVD), from 6500 to $312~ \Omega $ /⬜. With the 20-nm stress-engineered in situ SiN, the device not only provides a large output current of 1.05 A/mm but also demonstrates promising potential on the RF applications, which gives AlGaN material two records high cutoff frequency ${f} _{\text {T}}/{f} _{\text {max}}$ of 157 GHz/334 GHz for 100-nm gated device and 211 GHz/379 GHz for 70-nm gated device. During the continuous wave (CW) power measurement at 30 GHz, the 70-nm devices exhibit a large output power of 4.6 W/mm associated with a peak power-added efficiency (PAE) of 48.1% and a gain of 11.6 dB (${V} _{\text {ds}} =20$ V), and a high PAE of 53.8% with an output power density of 1.9 W/mm and a gain of 10.8 dB (${V} _{\text {ds}} =10$ V), respectively. The huge potential of the UTB-AlGaN/GaN is demonstrated for high-frequency and large-output power applications when it is combined with the in situ SiN, which is necessary for future communication systems. [ABSTRACT FROM AUTHOR]

In this article, we report on the high dc and RF performance of AlGaN/GaN high electron mobility transistors that employ Ti/Au/Al/Ni/Au metallization stack with shallow trench etching ohmic contact (STEOC). An excellent ohmic contact performance including low contact resistance (${R}_{C}$) of $0.28~\Omega \cdot $ mm and smooth surface morphology have been achieved simultaneously. Atomic force microscope (AFM) reveals a highly smooth surface morphology with a root mean square (rms) roughness of 6.3 nm even after 810 °C high-temperature annealing (HTA), achieving an improvement of 79% as compared to the conventional Ti/Al/Ni/Au ohmic contact (COC). A high-resolution transmission electron microscope (HRTEM) showed a glossy morphology with a continuous and uniform TiN layer formed in the interface for the STEOC sample, while a bumpy morphology caused from the Ni-Al complexes balling up and TiN island penetrating into the AlGaN/GaN heterostructure were observed for the conventional sample. Consequently, the fabricated transistors with the STEOC process show a high output current of 1.52 A/mm and low ON-resistance (${R}_{ \mathrm{ ON}}$) of $2.09~\Omega $ mm. In addition, a high current cutoff frequency (${f}_{T}$) of 60 GHz and maximum oscillation frequency (${f}_{\text {max}}$) of 150 GHz were obtained for the STEOC HEMT with a gate length (${L}_{\text {g}}$) of 150 nm. Sub-6 GHz continuous-wave mode power sweep measurements deliver a high power-added-efficiency (PAE) of 67%. These results show the significant potential of the STEOC process to facilitate the development of GaN-based power amplifier (PA) applied for 5G. [ABSTRACT FROM AUTHOR]