Search

Chlorine dioxide is widely used for pulp bleaching because of its high delignification selectivity. However, efficient and clean chlorine dioxide bleaching is limited by the complexity of the lignin structure. Herein, the oxidation reactions of phenolic (vanillyl alcohol) and non-phenolic (veratryl alcohol) lignin model species were modulated using chlorine dioxide. The effects of chlorine dioxide concentration, reaction temperature, and reaction time on the consumption rate of the model species were also investigated. The optimal consumption rate for the phenolic species was obtained at a chlorine dioxide concentration of 30 mmol·L−1, a reaction temperature of 40 °C, and a reaction time of 10 min, resulting in the consumption of 96.3% of vanillyl alcohol. Its consumption remained essentially unchanged compared with that of traditional chlorine dioxide oxidation. However, the consumption rate of veratryl alcohol was significantly reduced from 78.0% to 17.3%. Additionally, the production of chlorobenzene via the chlorine dioxide oxidation of veratryl alcohol was inhibited. The structural changes in lignin before and after different treatments were analyzed. The overall structure of lignin remained stable during the optimization of the chlorine dioxide oxidation treatment. The signal intensities of several phenolic units were reduced. The effects of the selective oxidation of lignin by chlorine dioxide on the pulp properties were analyzed. Pulp viscosity significantly increased owing to the preferential oxidation of phenolic lignin by chlorine dioxide. The pollution load of bleached effluent was considerably reduced at similar pulp brightness levels. This study provides a new approach to chlorine dioxide bleaching. An efficient and clean bleaching process of the pulp was developed.

Chronic wounds; Infection biomarker; Myeloperoxidase; Colorimetry Ferides i lesions; Biomarcadors d'infecció; Mieloperoxidasa; Colorimetria Heridas crónicas; Biomarcador de infección; Mieloperoxidasa; Colorimetría Current procedures for the assessment of chronic wound infection are time-consuming and require complex instruments and trained personnel. The incidence of chronic wounds worldwide, and the associated economic burden, urge for simple and cheap point-of-care testing (PoCT) devices for fast on-site diagnosis to enable appropriate early treatment. The enzyme myeloperoxidase (MPO), whose activity in infected wounds is about ten times higher than in non-infected wounds, appears to be a suitable biomarker for wound infection diagnosis. Herein, we develop a single-component foldable paper-based device for the detection of MPO in wound fluids. The analyte detection is achieved in two steps: (i) selective immunocapture of MPO, and (ii) reaction of a specific dye with the captured MPO, yielding a purple color with increasing intensity as a function of the MPO activity in infected wounds in the range of 20-85 U/mL. Ex vivo experiments with wound fluids validated the analytic efficiency of the paper-based device, and the results strongly correlate with a spectrophotometric assay.

A novel miniaturized and sustainable platform exploiting two merged paper-based substrates has been applied for the programmable pre-concentration of analytes of interest and electrochemical detection of mercury traces in drinking water using printable sensor strips. This strategy represents a novel versatile possibility in merging humble materials maximizing their impacts on analytical and remediation challenges.

Electrochemical aptamer-based (E-AB) sensors offer a powerful and general means for analyte detection in complex samples for various applications. Paper-based E-AB sensors could enable portable, low-cost, and rapid detection of a broad range of targets, but it has proven challenging to fabricate suitable three-electrode systems on paper. Here, we demonstrate a simple, economic, and environmentally-friendly strategy for fabricating aptamer-modified paper electrochemical devices (PEDs) via ambient vacuum filtration. The electrode material, shape, size, and thickness of the three-electrode PED system can be fully customized. We developed aptamer-modified PEDs that enable sensitive and specific detection of small molecules in minimally processed biosamples. The sensitivity and stability of the PEDs is comparable to E-AB sensors based on commercial gold electrodes. We believe our fabrication strategy can lead to the development of high performance PEDs that enable on-site detection of a variety of analytes, simplifying the development of portable sensors for real-world applications.

Hybrid nanomaterials fabricated by the heterogeneous integration of 1D (carbon nanotubes) and 2D (graphene oxide) nanomaterials showed synergy in electrical and mechanical properties. Here, we reported the infiltration of carboxylic functionalized single-walled carbon nanotubes (C-SWNT) into free-standing graphene oxide (GO) paper for better electrical and mechanical properties than native GO. The stacking arrangement of GO sheets and its alteration in the presence of C-SWNT were comprehensively explored through scanning electron microscopy, X-ray photoelectron spectroscopy (XPS) and X-ray diffraction. The C-SWNTs bridges between different GO sheets produce a pathway for the flow of electrical charges and provide a tougher hybrid system. The nanoscopic surface potential map reveals a higher work function of the individual functionalised SWNTs than surrounded GO sheets showing efficient charge exchange. We observed the enhanced conductivity up to 50 times and capacitance up to 3.5 times of the hybrid structure than the GO-paper. The laminate of polystyrene composites provided higher elastic modulus and mechanical strength when hybrid paper is used, thus paving the way for the exploitation of hybrid filler formulation in designing polymer composites.

This work reports on fully integrated “sample‐in‐signal‐out” microfluidic paper‐based analytical devices (μPADs) relying on bioluminescence resonance energy transfer (BRET) switches for analyte recognition and colorimetric signal generation. The devices use BRET‐based antibody sensing proteins integrated into vertically assembled layers of functionalized paper, and their design enables sample volume‐independent and fully reagent‐free operation, including on‐device blood plasma separation. User operation is limited to the application of a single drop (20–30 μL) of sample (serum, whole blood) and the acquisition of a photograph 20 min after sample introduction, with no requirement for precise pipetting, liquid handling, or analytical equipment except for a camera. Simultaneous detection of three different antibodies (anti‐HIV1, anti‐HA, and anti‐DEN1) in whole blood was achieved. Given its simplicity, this type of device is ideally suited for user‐friendly point‐of‐care testing in low‐resource environments.

The selectivity of the substitution reaction of phosphoryl chloride with organometallic reagents was investigated using NMR spectroscopy. This led to the discovery that the selectivity of the substitution reaction can be tuned by choosing a proper organometallic reagent. A phosphinate could be obtained by using a Grignard reagent whereas an organozinc reagent provided a phosphonate. Based on these results, one-pot synthetic methods for the preparation of phosphinates and phosphonates using commercially available starting materials were developed. Both methods allow the synthesis of a broad range of either phosphinate or phosphonate derivatives in a straightforward and general procedure. Moreover, using these one-pot procedures, mixed systems substituted with different alkyl/aryl groups can be prepared. ispartof: Synthesis (Germany) vol:50 issue:10 pages:2019-2026 status: published

H. Koga, N. Namba, T. Takahashi, M. Nogi, Y. Nishina. Renewable Wood Pulp Paper Reactor with Hierarchical Micro/Nanopores for Continuous‐Flow Nanocatalysis. ChemSusChem 2017, 10, 2560. https://doi.org/10.1002/cssc.201700576., Continuous-flow nanocatalysis based on metal nanoparticle catalyst-anchored flow reactors has recently provided an excellent platform for effective chemical manufacturing. However, there has been limited progress in porous structure design and recycling systems for metal nanoparticle-anchored flow reactors to create more efficient and sustainable catalytic processes. In this study, traditional paper is used for a highly efficient, recyclable, and even renewable flow reactor by tailoring the ultrastructures of wood pulp. The “paper reactor” offers hierarchically interconnected micro- and nanoscale pores, which can act as convective-flow and rapid-diffusion channels, respectively, for efficient access of reactants to metal nanoparticle catalysts. In continuous-flow, aqueous, room-temperature catalytic reduction of 4-nitrophenol to 4-aminophenol, a gold nanoparticle (AuNP)-anchored paper reactor with hierarchical micro/nanopores provided higher reaction efficiency than state-of-the-art AuNP-anchored flow reactors. Inspired by traditional paper materials, successful recycling and renewal of AuNP-anchored paper reactors were also demonstrated while high reaction efficiency was maintained.

Herein we demonstrate the first example of oligonucleotide-templated reaction (OTR) performed on paper, using lateral flow to capture and concentrate specific nucleic acid biomarkers on a test line. Quantitative analysis, using a low-cost benchtop fluorescence reader showed very high specificity down to the single nucleotide level and proved sensitive enough for amplification-free, on-chip, detection of endogenous concentrations of miR-150-5p, a recently identified predictive blood biomarker for preterm birth.

International audience; We developed a chemical method to covalently functionalize cellulose nanofibers and cellulose paper with mannoside ligands displaying a strong affinity for the FimH adhesin from pathogenic E. coli strains. Mannose-grafted cellulose proved efficient to selectively bind FimH lectin and discriminate pathogenic E. coli strains from non-pathogenic ones. These modified papers are valuable tools for diagnosing infections promoted by E.coli, such as cystitis or inflammatory bowel diseases, and the concept may be applicable to other life-threatening pathogens. The worldwide spread of antibiotic resistances raises serious health problems, and has driven the identification of new virulence factors and development of alternative antibacterial therapeutics. Mannose-binding FimH adhesin, expressed by Escherichia coli strains has been extensively studied as a target for disrupting bacterial attachment to the host cells. 1 Impressive results were obtained in the context of urinary tract infections (UTI), a prevalent infection type generally mediated by the attachment of uropathogenic E. coli strains (UPEC) to the highly mannosylated uroplakin transmembrane protein of urothelial lining cells. FimH antagonists orally administered to in vivo UTI mouse models, were shown to decrease the E.coli load in the bladder by several orders of magnitude, 2-4 making them competitive with conventional antibiotic treatment. 5,6 This concept was more recently extended to Crohn's disease (CD), an inflammatory disorder of the intestine where an altered gut microbiota, particularly the presence of adherent-invasive E. coli strains (AIEC), is suspected to play a key role in the pathogenesis. 7 Synthetic derivatives of heptylmannoside (HMan), a nanomolar FimH antagonist, 8 were shown to lower the AIEC bacterial level, signs of colitis and gut inflammation when administered per os (10 mg/kg) in CD mouse models. 9,10 Sensitive and rapid diagnostic systems are essential to evaluate the presence of E. coli expressing FimH adhesin in gut microenvironments in order to properly stratify patients before treatment. While the high prevalence of UPEC in the normally sterile urinary tract environment facilitates diagnosis, the AIEC niche is more complex, located at the ileal mucosa in 21 to 63% of CD patients, 11,12 within an ecological community of hundreds of symbiotic microorganisms. Furthermore, no specific biomarkers are currently effective at distinguishing AIEC from other commensal E. coli of the gut microbiota. Previously, it has been shown that AIEC pathobiont possesses specific allelic variants in the fimH gene, conferring them a high ability to adhere in vitro and to colonize the gut of CEABAC10 mice. 13 Establishing an approach to discriminate the strong mannose-binders from other bacteria would therefore be of tremendous importance for efficient diagnosis. In this work, we developed a heterogeneous support to specifically trap and accumulate pathogenic E.coli from biological fluids. Heptyl-α-D-mannoside (HMan) was grafted by click chemistry techniques onto cellulose nanofibers (CN) and cellulose paper (CP). HMan was previously identified as a potent binder of the isolated FimH lectin domain. 8 It should be noted that the lectin domain represents the high-affinity state of FimH under mechanical force and that full-length FimH display a lower affinity for mannosides. 14,15 Covalently functionalized CN or CP were characterized by Fourier transform spectroscopy (FTIR), elemental analysis, X-ray photo-electron spectrometry (XPS), and scanning electron microscopy (SEM). HMan-CN was first compared in vitro against CN grafted with lower FimH affinity ligands i.e. Man-CN lacking the hydrophobic heptyl chain, and HGlc-CN an analog with a glucose sugar that is not recognized by FimH lectin (Scheme 1). In addition, we switched the anomeric oxygen atom to a sulfur and synthesized HSMan-CN to prevent potential sugar hydrolysis from the surface by mannosidases. The modified CN were first assessed for their faculty to bind FimH and to prevent AIEC adhesion to intestinal cells. HMan-CN was then orally administered to the CEABAC10 mouse model of CD to assess its capacity to decrease AIEC in the feces of AIEC-infected mice and to act as a potential CD therapeutic. HM was next coated on CP and the capacity of the HMan-CP to selectively catch AIEC in solution was analyzed. Scheme 1. Chemical synthesis of the sugar-coated cellulose fibers.

A paper/ poly(methyl methacrylate) (PMMA) hybrid CD-like microfluidic SpinChip integrated with DNA probe-functionalized graphene oxide (GO) nanosensors was developed for multiplex quantitative LAMP detection (mqLAMP). This approach can simply and effectively address a major challenging problem of multiplexing in current LAMP methods.

The present study deals with the non-catalytic and catalytic wet oxidation (CWO) for the removal of persistent organic compounds from the pulping effluent. Two activated carbon-supported heterogeneous catalysts (Cu/Ce/AC and Cu/Mn/AC) were used for CWO after characterization by the following techniques: temperature-programmed reduction, Fourier transform infrared spectroscopy and thermo-gravimetric analysis. The oxidation reaction was performed in a batch high-pressure reactor (capacity = 0.7 L) at moderate oxidation conditions (temperature = 190°C and oxygen pressure = 0.9 MPa). With Cu/Ce/AC catalyst, the maximum chemical oxygen demand (COD), total organic carbon (TOC) and lignin removals of 79%, 77% and 88% were achieved compared to only 50% removal during the non-catalytic process. The 5-day biochemical oxygen demand (BOD5) to COD ratio (a measure for biodegradability) of the pulping effluent was improved to 0.52 from an initial value of 0.16. The mass balance calculations for solid recovered after CWO reaction showed 8% and 10% deduction in catalyst mass primarily attributed to the loss of carbon and metal leaching. After the CWO process, carbon deposition was also observed on the recovered catalyst which was responsible for around 3–4% TOC reduction.

For the first time, a paper based enzymatic fuel cell is used as self-recharged supercapacitor. In this supercapacitive enzymatic fuel cell (SC-EFC), the supercapacitive features of the electrodes are exploited to demonstrate high power output under pulse operation. Glucose dehydrogenase-based anode and bilirubin oxidase-based cathode were assembled to a quasi-2D capillary-driven microfluidic system. Capillary flow guarantees the continuous supply of glucose, cofactor and electrolytes to the anodic enzyme and the gas-diffusional cathode design provides the passive supply of oxygen to the catalytic layer of the electrode. The paper-based cell was self-recharged under rest and discharged by high current pulses up to 4mAcm−2. The supercapacitive behavior and low equivalent series resistance of the cell permitted to achieve up to a maximum power of 0.87mWcm−2 (10.6mW) for pulses of 0.01s at 4mAcm−2. This operation mode allowed the system to achieve at least one order of magnitude higher current/power generation compared to the steady state operation.

Paper surfaces (Whatman filter papers, Kimwipes®, and Japanese Washi papers) were employed as support for gold nanoparticles (AuNPs) deposited by the seed-mediated growth method. The AuNP-modified paper or textile was brought into “weak” (or non-permanent) contact with a glassy carbon electrode and immersed into aqueous electrolyte media. Electrochemical responses for the Fe(CN)64−/Fe(CN)63− redox system in 0.1 M phosphate buffer (pH 7.0) and 1.0 M KCl solutions were investigated by voltammetry and impedance methods. Even for weakly contacted AuNP catalysts of relatively low density faster electron transfer was observed. Particle sizes of at least 20 nm diameter were required. There was no permanent contact from AuNP catalysts to the electrode and the process was therefore termed “weak contact catalysis”. The method is proposed as a rapid and novel catalyst screening tool with potential applications in fuel cell and sensor technologies. Keywords: Modified electrodes, Gold nanoparticles, Electron-transfer reactions, Textile, Paper, Catalyst support, Seed-mediated growth method, Voltammetry, Impedance, Contact-electrocatalysis

Wt% of aragonite, a CaCO(3) polymorph, increased with higher hydraulic activity ( degrees C) of limestone in precipitated calcium carbonate (PCC) from the lime-soda process (Ca(OH)(2)-NaOH-Na(2)CO(3)). Only calcite, the most stable polymorph, was crystallized at hydraulic activity under 10 degrees C, whereas aragonite also started to crystallize over 10 degrees C. The crystallization of PCC is more dependent on the hydraulic activity of limestone than CaO content, a factor commonly used to classify limestone ores according to quality. The results could be effectively applied to the determination of polymorphs in synthetic PCC for eco-friendly paper manufacture.

The cellulose paper treated in proportional mixture systems showed higher liquid absorption compare to only EtOH and MeOH treatments. It was approximately 40-70% and 50-91% higher for EtOH-NaOH and MeOH-NaOH treated papers, respectively. All conditions apparently bring about an effect of decreased strength for papers. The lowest tensile strength of 13.0 N/mm was found with EtOH and NaOH treated samples after 5(th) repeating wetting-drying stage. But, some conditions gave approximately 21-59.5% higher stretch than untreated samples. The pore size distributions of papers were evaluated with Simons stain procedure and experimental results usually consisted with sorption data. The less intense CH(2)-CH(2)- vibrations (1450-1700 cm(-1)) and C-C and C-O-C peak areas in FTIR spectra indicates lowering H-bonds in solvent treated and dried paper network structure.

Would it not be nice to have an organic solvent nanofiltration membrane made from renewable resources that can be manufactured as simply as producing paper? Here the production of nanofiltration membranes made from nanocellulose by applying a papermaking process is demonstrated. Manufacture of the nanopapers was enabled by inducing flocculation of nanofibrils upon addition of trivalent ions.

The present study investigated the performance of activated carbon and alumina supported non-noble metal based catalysts during the catalytic wet oxidation (CWO) of ferulic acid (a lignin model compound). The heterogeneous catalysts, Cu/Ce/AC, Cu/Ce/Al2O3, Cu/Mn/AC and Cu/Mn/Al2O3 (mass ratio = 3:3:4), were prepared by metal impregnation while Cu/Mn/Ce (mass ratio = 3:3:4) catalyst was synthesized by co-precipitation method. The CWO reaction was performed in a batch reactor at mild conditions (temperature = 120 degrees C and oxygen pressures = 0.5 MPa) with a catalyst concentration of 3 g/1 for 3 h duration. Among all the catalysts, Cu/Ce/AC catalyst showed the maximum chemical oxygen demand (COD) and total organic carbon (TOC) removals (88% and 82%, respectively) from the wastewater. The ferulic acid removal was resulted from a combination of reactions (such as oxidation, hydrolysis, decarboxylation and adsorption). During the CWO reaction, oxalic acid was identified as the major by-product but mean oxidation state of carbon and TOC balance calculation indicated also the presence of other compounds. A significant difference in the surface characteristics of the fresh and thermally regenerated catalysts (after CWO) was observed. The first time reuse of Cu/Ce/AC catalyst caused 6% lesser reduction in TOC than the fresh catalyst though no considerable reduction in the catalytic activity could be observed after second reuse of the catalyst. The future study should plan for the determination of the change in biodegradability after the treatment and the effectiveness of CWO on real pulping effluent. (C) 2014 Elsevier B.V. All rights reserved.

This work presents a simple, low cost method for creating microelectrodes for electrochemical paper-based analytical devices (ePADs). The microelectrodes were constructed by backfilling small holes made in polyester sheets using a CO2 laser etching system. To make electrical connections, the working electrodes were combined with silver screen-printed paper in a sandwich type two-electrode configuration. The devices were characterized using linear sweep voltammetry, and the results are in good agreement with theoretical predictions for electrode size and shape. As a proof-of-concept, cysteine was measured using cobalt phthalocyanine as a redox mediator. The rate constant (k(obs)) for the chemical reaction between cysteine and the redox mediator was obtained by chronoamperometry and found to be on the order of 10(5) s(-1) M(-1). Using a microelectrode array, it was possible to reach a limit of detection of 4.8 μM for cysteine. The results show that carbon paste microelectrodes can be easily integrated with paper-based analytical devices.

The closure of water circuits within pulp and paper mills has resulted in a higher contamination load of the final mill effluent, which must consequently be further treated in many cases to meet the standards imposed by the legislation in force. Different treatment strategies based on advanced oxidation processes (ozonation and TiO2-photocatalysis), and their combination with biological treatment (MBR), are herein assessed for effluents of a recycled paper mill and a kraft pulp mill. Ozone treatment achieved the highest efficiency of all. The consumption of 2.4 g O3 L−1 resulted in about a 60% COD reduction treating the effluent from the kraft pulp mill at an initial pH = 7; although it only reached about a 35% COD removal for the effluent of the recycled paper mill. Otherwise, photocatalysis achieved about a 20–30% reduction of the COD for both type of effluents. In addition, the effluent from the recycled paper mill showed a higher biodegradability, so combinations of these AOPs with biological treatment were tested. As a result, photocatalysis did not report any significant COD reduction improvement whether being performed as pre- or post-treatment of the biological process; whereas the use of ozonation as post-biological treatment enhanced COD removal a further 10%, summing up a total 90% reduction of the COD for the combined treatment, as well as it also supposed an increase of the presence of volatile fatty acids, which might ultimately enable the resultant wastewater to be recirculated back to further biological treatment.

Pencil it in: Mechanical abrasion of compressed single-walled carbon nanotubes (SWCNTs) on the surface of paper produces sensors capable of detecting NH[subscript 3] gas at sub-ppm concentrations. This method of fabrication is simple, inexpensive, and entirely solvent-free, and avoids difficulties arising from the inherent instability of many SWCNT dispersions., Massachusetts Institute of Technology. Institute for Soldier Nanotechnologies (W911NF-07-D-004), National Institutes of Health (U.S.) (National Cancer Institute (U.S.) Postdoctoral Fellowship Grant F32A1571997)

Photocatalysis using ZnO-Fe2O3 coupled catalyst removed partially the organic matter dissolved in kraft black liquor obtained from pinus wood cooking. The photo-assisted oxidation using different ZnO/Fe2O3 ratios was studied following the CO, evolution during the course of the reaction. A synergy of the composite improves the mineralization observed. The optimal ZnO to Fe2O3 ratio varied from 0.5 to 0.7 which allowed the highest mineralization rates.

The oxidation of a 186 ppm 6-chlorovanillin solution was performed using impregnated TiO2 glass rings in a 1 l photochemical reactor. Fifty per cent degradation was obtained after 60 min with recirculation of the solution. Then, oxidised samples were submitted under aerobic conditions to bacterial degradation in the Pseudomonas paucimobilis (S37) and Burkholderia cepacia (PZK). Both selected aerobic bacteria degrade more efficiently the photocatalysed samples, being PZK strain better than S37. A first-order kinetic was observed in both systems photocatalytic and bacterial degradation.

Four different 1-aminocyclohexanes bearing a tethered thioxanthone group in the 2-position were prepared. The synthesis commenced with the respective N-protected β-amino acids, the carboxyl group of which was employed for the introduction of the thioxanthone moiety. After construction of the thioxanthone and protecting group removal, the conversion of the amino group into the respective thiourea was accomplished by treatment with N-3,5-bis(trifluoromethyl)phenyl isothiocyanate and yielded the title compounds in which the thioxanthone resides in different spatial positions relative to the thiourea motif. Overall yields varied between 20–35%.

This paper describes the organosolv delignification of depithed bagasse using glycerol–water mixtures without a catalyst. The experiments were performed using two separate experimental designs. In the first experiment, two temperatures (150 and 190 °C), two time periods (60 and 240 min) and two glycerol contents (20% and 80%, v/v) were used. In the second experiment, which was a central composite design, the glycerol content was maintained at 80%, and a range of temperatures (141.7–198.3 °C) and time (23–277 min) was used. The best result, obtained with a glycerol content of 80%, a reaction time of 150 min and a temperature of 198.3 °C, produced pulps with 54.4% pulp yield, 7.75% residual lignin, 81.4% delignification and 13.7% polyose content. The results showed that high contents of glycerol tend to produce pulps with higher delignification and higher polyoses content in relation to the pulps obtained from low glycerol content reactions. In addition, the proposed method shows potential as a pretreatment for cellulose saccharification.