Search

The increase in anthropogenic pollution raises serious concerns regarding contamination of water bodies and aquatic species with potential implications on human health. Pharmaceutical compounds are a type of contaminants of emerging concern that are increasingly consumed and, thus, being frequently found in the aquatic environment. In this sense, an electrochemical sensor based on an unmodified and untreated carbon fiber paper (CPS—carbon paper sensor) was simply employed for the analysis of trimethoprim antibiotic in fish samples. First, the analytical conditions were thoroughly optimized in order for the CPS to achieve maximum performance in trimethoprim determination. Therefore, an electrolyte (0.1 M Britton–Robinson buffer) pH of 7 was selected and for square wave voltammetry parameters, optimum values of amplitude, frequency and step potential corresponded to 0.02 V, 50 Hz, and 0.015 V, respectively, whereas the deposition of analyte occurred at +0.7 V for 60 s. In these optimum conditions, the obtained liner range (0.05 to 2 µM), sensitivity (48.8 µA µM−1 cm−2), and LOD (0.065 µM) competes favorably with the commonly used GCE-based sensors or BDD electrodes that employ nanostructuration or are more expensive. The CPS was then applied for trimethoprim determination in fish samples after employing a solid phase extraction procedure based on QuEChERS salts, resulting in recoveries of 105.9 ± 1.8% by the standard addition method. [ABSTRACT FROM AUTHOR]

A novel electrochemical sensor was developed for the detection of salivary cortisol levels. The sensor employs a combination of a molecularly imprinted polymer (MIP) and gold nanoparticles (AuNPs) that are electrodeposited onto a screen-printed electrode (SPE). The study utilised density functional theory and molecular docking techniques to determine the geometry of molecular orbitals, electrostatic potential energies, and binding energy of cortisol and the polymers. The thin film of cortisol-imprinted polymer on the SPE was created by electro-polymerizing pyrrole and thiophene-3-carboxylic acid on the electrode surface along with cortisol as the template molecule. The MIP film was characterised using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and electrochemical techniques. The sensor exhibited a linear response in the concentration range of 0.05 nmol L−1 to 2.5 μmol L−1, with a limit of detection of 0.01 nmol L−1, as determined by differential pulse voltammetry. This method offers a simple yet efficient and sensitive approach to detecting cortisol levels in human saliva samples. [Display omitted] • A new electrochemical sensor is presented that can selectively detect salivary cortisol levels using a molecularly imprinted polymer (MIP). • Gold nanoparticles (AuNPs) were electrochemically deposited on a screen-printed electrode (SPE) as a substrate for the cortisol-imprinted polymer thin film. • The cortisol-imprinted polymer thin film was synthesized on the SPE through the electro-polymerization of pyrrole and thiophene-3-carboxylic acid. • The study used density functional theory and molecular docking techniques to compute the geometry of molecular orbitals, electrostatic potential energies, and binding energy for the interacting molecules. • The differential pulse voltammetry method showed a linear response in the concentration range of 0.05 nmol L−1 to 2.5 μmol L−1 with a limit of detection of 0.016 nmol L−1. • This simple approach is an efficient and sensitive method for detecting cortisol levels in human saliva samples. [ABSTRACT FROM AUTHOR]

In recent years, analytical chemistry has been facing new challenges, particularly in developing low-cost, green, and easy-to-reproduce methods. In this work, a simple, reproducible, and low-cost electrochemical (voltammetric) molecularly imprinted polymer (MIP) sensor was designed specifically for the detection of trazodone (TZD). Trazodone (TZD) is an antidepressant drug consumed worldwide since the 1970s. By combining electropolymerization (surface imprinting) with screen-printed electrodes (SPCEs), the sensor is easy to prepare, is environmentally friendly (uses small amounts of reagents), and can be used for in situ analysis through integration with small, portable devices. The MIP was obtained using cyclic voltammetry (CV), using 4-aminobenzoic acid (4-ABA) as the functional monomer in the presence of TZF molecules in 0.1 M HCl. Non-imprinted control was also constructed in the absence of TZD. Both polymers were characterized using CV, and TZD detection was performed with DPV using the oxidation of TZD. The polymerization conditions were studied and optimized. Comparing the TZD signal for MIP/SPCE and NIP/SPCE, an imprinting factor of 71 was estimated, indicating successful imprinting of the TZD molecules within the polymeric matrix. The analytical response was linear in the range of 5–80 µM, and an LOD of 1.6 µM was estimated. Selectivity was evaluated by testing the sensor for molecules with a similar structure to TZD, and the ability of MIP/SPCE to selectively bind to TZD was proven. The sensor was applied to spiked tap water samples and human serum with good recoveries and allowed for a fast analysis (around 30 min). [ABSTRACT FROM AUTHOR]

In this work, a disposable electrochemical (voltammetric) molecularly imprinted polymer (MIP) sensor for the selective determination of diclofenac (DCF) was constructed. The proposed MIP-sensor permits fast (30 min) analysis, is cheap, easy to prepare and has the potential to be integrated with portable devices. Due to its simplicity and efficiency, surface imprinting by electropolymerization was used to prepare a MIP on a screen-printed carbon electrode (SPCE). MIP preparation was achieved by cyclic voltammetry (CV), using dopamine (DA) as a monomer in the presence of DCF. The differential pulse voltammetry (DPV) detection of DCF at MIP/SPCE and non-imprinted control sensors (NIP) showed an imprinting factor of 2.5. Several experimental preparation parameters were studied and optimized. CV and electrochemical impedance spectroscopy (EIS) experiments were performed to evaluate the electrode surface modifications. The MIP sensor showed adequate selectivity (in comparison with other drug molecules), intra-day repeatability of 7.5%, inter-day repeatability of 11.5%, a linear range between 0.1 and 10 μM (r2 = 0.9963) and a limit of detection (LOD) and quantification (LOQ) of 70 and 200 nM, respectively. Its applicability was successfully demonstrated by the determination of DCF in spiked water samples (river and tap water). [ABSTRACT FROM AUTHOR]

The extracellular domain of the human epidermal growth factor receptor 2 (HER2-ECD) is a protein breast cancer biomarker. Its quantification in peripheral blood could provide an important contribution to diagnostics and patient follow-up. In this work an electrochemical molecularly imprinted polymer (MIP) sensor for the quantification of HER2-ECD was developed. The MIP was electropolymerized by cyclic voltammetry using a solution containing phenol and HER2-ECD on a screen-printed gold electrode (AuSPE). The sensor was characterized by cyclic voltammetry and electrochemical impedance spectroscopy. The analysis of HER2-ECD was performed by differential pulse voltammetry using ([Fe(CN) 6 ] 3−/4− as redox probe. The linear range was established in the concentration interval from 10 to 70 ng/mL HER2-ECD, with a limit of detection of 1.6 ng/L and a limit of quantification of 5.2 ng/mL. Through the analysis of other protein biomarkers, the MIP sensor was found to be selective. Furthermore, these proteins did not interfere in the analysis of the selected biomarker. The developed sensor was used for the analysis of spiked human serum samples, providing adequate recovery values and precise results. The outcomes of this study indicate that the developed MIP sensor could be useful in the non-invasive analysis of HER2-ECD in breast cancer patients. [ABSTRACT FROM AUTHOR]

The incidence of breast cancer has been increasing over the years. To control and monitor this disease several tumor biomarkers have been proposed for early diagnosis, patient follow-up and/or treatment guidance. The only serum breast cancer biomarker in current use is the cancer antigen 15-3 (CA 15-3). In this work a molecularly imprinted polymer (MIP)-based electrochemical (voltammetric) sensor to monitor breast cancer was developed, based on direct surface imprinting of CA 15-3 on a screen-printed gold electrode (Au-SPE). The imprinting was performed in two steps: (1) adsorption of CA 15-3 on the surface of the Au-SPE and (2) electropolymerization of 2-aminophenol around the adsorbed protein. After extraction of the imprinted protein voltammetric analysis was conducted using hexacyanoferrate(II/III) as redox probe, measuring the signals before and after protein binding. The sensor was characterized by voltammetric techniques and electrochemical impedance spectroscopy, and the analytical responses of imprinted and non-imprinted polymer sensors were studied. A linear relationship between the peak current intensity of the redox probe and the logarithm of CA 15-3 concentration was established between 5 and 50 U mL −1 , achieving a limit of detection of 1.5 U mL −1 . The prepared MIP-sensor provides fast (15 min) analysis and is cheap, easy to prepare, disposable and could easily be integrated in small portable point-of care devices. [ABSTRACT FROM AUTHOR]

Naloxone (NLX) is a pharmaceutical used as opioid antagonist. A molecular imprinted polymer electrochemical sensor for simple and rapid detection of NLX was prepared through the modification of commercial available screen printed carbon electrode (SPCE). The SPCE was modified with multi-walled carbon nanotubes (MWCNT) by drop coating to increase the signal response and improve the sensitivity. The MIP preparation was carried out via in situ electropolymerization using 4-aminobenzoic acid (4-ABA) as functional monomer. The morphology of the obtained sensor was characterized by scanning electron microscopy (SEM). Several parameters controlling the preparation and performance of the MIP sensor were studied and optimized. The electrochemical behavior of NLX at MIP and control non-imprinted (NIP) sensor was evaluated by differential pulse voltammetry (DPV), demonstrating a better MIP response and the success of the imprinting. The proposed MIP/MWCNT/SPCE sensor showed a linear relationship between peak current intensity and NLX concentration in the range between 0.25 and 10.0 μM, with limits of detection (LOD) and quantification (LOQ) of 0.20 μM and 0.67 μM respectively. The repeatability and reproducibility were also tested with relative standard deviations (RSD) of 4.6 and 9.6% respectively. Moreover, the applicability of the method was successfully confirmed with detection of NLX in biological samples (urine and human serum). The sensor is promising to be used for screening NLX in point-of-care people with opioid overdose. [ABSTRACT FROM AUTHOR]

The remarkable features of a carbon fiber paper sensor (CP) were employed for detection of the estrogenic hormone 17α-ethinylestradiol (EE2), considered a contaminant of emerging concern due to its potential ecotoxicity and widespread in the aquatic ecosystems. In this work, an unpreceded CP pre-treatment study was conducted with the (Il)-hexacyanoferrate(III) ion pair, however a bare sensor without pre-treatment revealed higher efficiency on the oxidation of EE2 compared to a chemical and electrochemical pre-treated CP and a gold nanoparticles modified CP, being thus selected for EE2 determinations. The analytical conditions were thoroughly optimized in terms of electrolyte pH (pH 7), differential pulse voltammetry parameters (modulation time 0.003 s, amplitude 0.09 V, interval time 0.1 s and step potential 0.01 V), and analyte preconcentration potential (0.4 V) and time (180 s). The hormone can be determined by the CP in a wide linear range from 0.1 to 1000 nM, achieving a detection limit of 0.14 ± 0.005 nM and an outstanding sensitivity of 1636 ± 232 μA μM−1 cm−2 in the lowest linear zone (0.1–1 nM). The sensor was validated in river water and fish reaching good recoveries (91.2 ± 4.6 to 109.0 ± 7.1%), reproducibility and repeatability. Moreover, the sensor showed high selectivity to EE2 in the presence of several potential interfering compounds and frequently prescribed drugs, though it could not discriminate the similar hormone, 17β-estradiol, being the total concentration obtained in this case. CP-based sensors emerge as efficient electroanalytical tools, suggesting that modification of the surface may not always be beneficial in terms of sensitivity. [Display omitted] • A simple and effective carbon paper sensor was used for 17α-ethinylestradiol sensing. • The best analytical signal was obtained with an untreated and unmodified carbon paper. • The optimized sensor achieved high sensitivity (1636 μA μM−1 cm−2) and LOD of 0.14 nM. • Application in complex samples of fish resulted in recoveries from 102 to 109%. • Carbon paper sensors can be become valuable tools in the electroanalytical field. [ABSTRACT FROM AUTHOR]

In this work, a norfloxacin selective modified glassy carbon electrode (GCE) based on a molecularly imprinted polymer (MIP) as electrochemical sensor was developed. A suspension of multi-walled carbon nanotubes (MWCNTs) was deposited on the electrode surface. Subsequently, a molecularly imprinted film was prepared by electropolymerization, via cyclic voltammetry of pyrrole (PPy) in the presence of norfloxacin (NFX) as the template molecule. A control electrode (NIP) was also prepared. Scanning electron microscopy (SEM) and cyclic voltammetry in a ferrocyanide solution were performed for morphological and electrochemical characterisation, respectively. Several experimental parameters were studied and optimised. For quantification purposes the MIP/MWCNT/GCE was immersed in NFX solutions for 10 min, and the detection was performed in voltammetric cell by square wave voltammetry. The proposed sensor presented a linear behaviour, between peak current intensity and logarithmic concentration of NFX between 1 × 10 −7 and 8 × 10 −6 M. The obtained results presented good precision, with a repeatability of 4.3% and reproducibility of 9% and the detection limit was 4.6 × 10 −8 M ( S/N = 3). The developed sensor displayed good selectivity and operational lifetime, is simple to fabricate and easy to operate and was successfully applied to the analysis of NFX in urine samples. [ABSTRACT FROM AUTHOR]

A novel electrochemical sensor for ochratoxin A (OTA) detection was fabricated through the modification of a glassy carbon electrode (GCE) with multiwalled carbon nanotubes (MWCNTs) and a molecularly imprinted polymer (MIP). The MWCNTs dramatically promoted the sensitivity of the developed sensor, while polypyrrole (PPy) imprinted with OTA served as the selective recognition element. The imprinted PPy film was prepared by electropolymerization of pyrrole in the presence of OTA as a template molecule via cyclic voltammetry (CV). The electrochemical oxidation of OTA at the developed sensor was investigated by CV and differential pulse voltammetry (DPV). The developed MIP/MWCNT/GCE sensor showed a linear relationship, when using DPV, between peak current intensity and OTA concentration in the range between 0.050 and 1.0 μM, with limits of detection (LOD) and quantification of 0.0041 μM (1.7 μg/L) and 0.014 μM (5.7 μg/L) respectively. With the developed sensor precise results were obtained; relative standard deviations of 4.2% and 7.5% in the evaluation of the repeatability and reproducibility, respectively. The MIP/MWCNT/GCE sensor is simple to fabricate and easy to use and was successfully applied to the determination of OTA in spiked beer and wine samples, with recoveries between 84 and 104%, without the need of a sample pre-treatment step. [ABSTRACT FROM AUTHOR]

Atorvastatin (ATV) is a statin member consumed in high quantities worldwide. In response to that, the occurrence of ATV in environmental waters has become a reality, highlighting the need of rapid and sensitive analytical devices for its monitoring. In this work, the first electrochemical molecularly imprinted polymer (MIP) sensor for the detection of ATV in water samples is presented. Computational studies were conducted based on quantum mechanical (QM) calculations and molecular dynamics (MD) simulations for rational selection of a suitable functional monomer and to study in detail the template-monomer interaction, respectively. The sensor was prepared by electropolymerisation of the selected 4-aminobenzoic acid (ABA) monomer with ATV, acting as template, on screen printed carbon electrode (SPCE). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were applied to characterise the modified electrode surfaces. The quantitative measurements were carried out with differential pulse voltammetry (DPV) in 0.1 M phosphate buffer (pH = 7). After investigation and optimisation of important experimental parameters, a linear working range down to 0.05 μmol L−1 was determined with a correlation coefficient of 0.9996 and a limit of detection (LOD) as low as 0.049 μmol L−1 (S/N = 3). High sensitivity and selectivity of the prepared sensor were demonstrated with the ability to recognise ATV molecules over its closer structural analogues. Moreover, the sensor was quickly and successfully applied in spiked water samples, proving its potential for future on-site monitoring of ATV in environmental waters. [Display omitted] • A disposable electrochemical MIP sensor for atorvastatin (ATV) detection was designed. • Efficient prediction of a functional monomer was achieved based on QM calculations. • MD simulations allowed to understand the ATV-monomer interaction. • High selectivity and sensitivity were obtained by a direct detection method. • The sensor was successfully applied in water samples. [ABSTRACT FROM AUTHOR]

A novel sensitive electrochemical sensor was developed by electropolymerization of pyrrole (PY) and molecularly imprinted polymer (MIP) which was synthesized onto a glassy carbon electrode (GCE) in aqueous solution using cyclic voltammetry in the presence of Trimethoprim (TMP) as template molecules. Furthermore, a previous electrode modification was performed by deposition of a suspension of graphene on the electrode's surface. The performance of the imprinted and non-imprinted (NIP) films was evaluated by impedance spectroscopy (EIS) and cyclic voltammetry (CV) of a ferric solution. The molecularly imprinted film exhibited a high selectivity and sensitivity toward TMP. The sensor presented a linear range, between peak current intensity and logarithm of TMP concentration between 1.0×10−6 and 1.0×10−4 M. The results were accurate (with recoveries higher than 94%), precise (with standard deviations less than 5%) and the detection limit was 1.3×10−7 M. The new sensor is selective, simple to construct and easy to operate. The MIP sensor was successfully applied to quantify TMP in urine samples. [ABSTRACT FROM AUTHOR]

• Molecularly imprinted polymer sensor for bisphenol-A was developed. • Molecular interactions of Bisphenol-A on polymer was computationally analysed. • Bisphenol-A imprinted polypyrrole electrochemically synthesised on the reduced graphene oxide film. • Bisphenol-A detected in bovine milk and water samples stored from polycarbonate bottles. Bisphenol A (BPA) contamination from food packaging material has been a major concern in recent years, due to its potential endocrine-disrupting effects on humans, especially infants and children. This paper reports the detection of BPA using an electrochemical sensor based on molecularly imprinted polymer (MIP). Electrochemically reduced graphene oxide coated glassy carbon electrode used for this study. Density functional theory (DFT) at B3LYP/6–31 + G (d,p) level was used to calculate the molecular-level interaction between BPA and MIP. The pyrrole electrochemically polymerized in the presence of template molecule BPA on the electrode surface. BPA imprinted cavities were formed by removing entrapped BPA molecules from the polypyrrole film. MIP electrode was used for the determination of BPA in standard and real samples by differential pulse voltammetry. The peak current shows the linear relationship to the logarithmic concentration of BPA between 750 and 0.5 nmolL−1 with a correlation coefficient, R2 = 0.992. The limit of detection was found to be 0.2 nmolL−1 (S/N = 3). The reproducibility and repeatability of the sensor were also studied. [ABSTRACT FROM AUTHOR]

• First time a selective MIP electrochemical sensor was developed for Furazolidone (FZD). • QM calculations and MD simulations were used to select the best functional monomer and the optimum polymerisation conditions. • The sensor constructed based on MIP-CPE-MWCNTs showed high selectivity and sensitivity. • The proposed sensor was successfully applied for FZD detection in water samples without any pre-treatment step. Determination of antibiotics in environmental waters is an important global issue. Although furazolidone (FZD) was banned from use in food-producing animals, owing to its mutagenic and carcinogenic effects, this antibiotic has been illegally used across the world and its presence in environment have being noted. In this work, the first selective molecularly imprinted polymer (MIP) was developed for electrochemical detection of FZD. It was constructed based on the modification of the traditional carbon paste electrode (CPE) with MIP microparticles, followed by introduction of multi-walled carbon nanotubes (MWCNTs). Quantum mechanical (QM) calculations and molecular dynamics (MD) simulations were performed to allow rational selection of an appropriate functional monomer and to simulate the best pre-polymerisation conditions, respectively. The MIP were synthetized by polymerization using 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) as monomer and FZD as template molecule. The MIP microparticles were then incorporated on CPE-MWCNTs and the electrochemical analysis of FZD were evaluated by differential pulse voltammetry (DPV). After optimisation of experimental conditions, the MIP-CPE-MWCNTs sensor exhibited a good linear response over the concentration range of 0.01 μM to 1 μM with a correlation coefficient of 0.9995. The limit of detection (LOD) was found to be 0.03 μM (S/N = 3). Due to high imprinting efficiency the sensor displayed selectivity to recognise FZD molecules and it was successfully applied in water samples where excellent recovery values (over 90 %) were obtained. The proposed sensor provides an efficient and promising sustainable strategy for monitorisation of FZD in environmental waters. [ABSTRACT FROM AUTHOR]