Search

Electron transport layers (ETLs) are crucial for achieving efficient and stable planar perovskite solar cells (PSCs). Reports on versatile inorganic ETLs using a simple film fabrication method and applicability for both low‐cost planar regular and inverted PSCs with excellent efficiencies (>22%) and high stability are very limited. Herein, we employ a novel inorganic ZnSe as ETL for both regular and inverted PSCs to improve the efficiency and stability using a simple thermal evaporation method. The TiO2‐ZnSe‐FAPbI3 heterojunction could be formed, resulting in an improved charge collection and a decreased carrier recombination further proved through theoretical calculations. The optimized regular PSCs based on TiO2/ZnSe have achieved 23.25% efficiency with negligible hysteresis. In addition, the ZnSe ETL can also effectively replace the unstable bathocuproine (BCP) in inverted PSCs. Consequently, the ZnSe‐based inverted device realizes a champion efficiency of 22.54%. Moreover, the regular device comprising the TiO2/ZnSe layers retains 92% of its initial PCE after 10:00 h under 1 Sun continuous illumination and the inverted device comprising the C60/ZnSe layers maintains over 85% of its initial PCE at 85 °C for 10:00 h. This highlights one of the best results among universal ETLs in both regular and inverted perovskite photovoltaics. [ABSTRACT FROM AUTHOR]

Understanding the function of moisture on perovskite is challenging since the random environmental moisture strongly disturbs the perovskite structure. Here, we develop various N2-protected characterization techniques to comprehensively study the effect of moisture on the efficient cesium, methylammonium, and formamidinium triple-cation perovskite (Cs0.05FA0.75MA0.20)Pb(I0.96Br0.04)3. In contrast to the secondary measurements, the established air-exposure-free techniques allow us directly monitor the influence of moisture during perovskite crystallization. We find a controllable moisture treatment for the intermediate perovskite can promote the mass transportation of organic salts, and help them enter the buried bottom of the films. This process accelerates the quasi-solid-solid reaction between organic salts and PbI2, enables a spatially homogeneous intermediate phase, and translates to high-quality perovskites with much-suppressed defects. Consequently, we obtain a champion device efficiency of approaching 24% with negligible hysteresis. The devices exhibit an average T80-lifetime of 852 h (maximum 1210 h) working at the maximum power point. Perovskite structure is disturbed by environmental moisture, limiting the device performance. Here, Wei et al. monitor the effect of moisture during the growth by N2-protected characterization techniques, and obtain an operationally stable perovskite solar cell with efficiency approaching 24%. [ABSTRACT FROM AUTHOR]

Carbon-based perovskite solar cells aroused huge attention for their simple, low-cost device fabrication processing and excellent stability. However, the fully low-temperature preparation and flexibility of carbon-based perovskite solar cells remain huge challenges. Here we demonstrate the fabrication of carbon-based perovskite solar cells processed at fully low-temperature, which take thermally evaporated cadmium sulfide as efficient electron transport layer, and obtain an optimal power conversion efficiency of 13.22%. With the decoration of PCBM, the separation of charges at the interface is facilitated and the recombination is hindered, so a higher fill factor is obtained and the efficiency is further improved to 14.28%. Our devices also exhibit good long-term durability and excellent ultraviolet stability. Based on the fully low-temperature preparation process, carbon-based flexible devices are further developed with an optimal efficiency over 9% and considerable mechanical stability, which can serve as the roof-top photovoltaics and power sources for wearable devices. Image 1 • Fully low-temperature processed and flexible carbon-based PSCs with excellent efficiency and stability are demonstrated. • First use of CdS as electron transport layer for carbon-based PSCs. • With the decoration of PCBM, efficiency of the best-performing device is greatly enhanced. [ABSTRACT FROM AUTHOR]

Abstract Fullerenes have been widely used as the electron transport layers (ETL) for planar-heterojunction perovskite solar cells (PSCs), due to their superior abilities in electron transporting, hysteresis suppression and low-temperature processing. Here, we demonstrate a novel inverted PSC with evaporated C 60 as ETL and dopant-free copper phthalocyanine (CuPc) as hole transport layer (HTL). The C 60 ETL can not only transport photogenerated electrons, but also passivate grain boundaries and surfaces of perovskite films effectively. By optimizing the thickness of the C 60 ETL, a champion power conversion efficiency (PCE) of 16.72% is obtained with almost no hysteresis and less than 10% decay in efficiency is observed during a two-week stability test. To the best of our knowledge, this is the highest efficiency of the inverted PSCs employing CuPc as HTL. For comparison, the devices using PCBM as ETL are also prepared and only achieve a highest efficiency of 15.74%. Various characterizations and analyses attest the enhanced charge transport and extraction as well as suppressed charge recombination and hysteresis for the C 60 -based devices. Since all the processes are accomplished under a low temperature, this enable us to fabricate flexible PSCs on polyethylene terephthalate (PET) substrates with a highest PCE of 12.96%. Our work provides a new strategy for fabricating cost-effective, highly efficient and hysteresis-free flexible PSCs in mass production. Graphical abstract Novel efficient C 60 -based inverted perovskite solar cells with negligible hysteresis are demonstrated. A champion power conversion efficiency (PCE) of 16.72% and 12.96% is obtained for the devices prepared on rigid and flexible substrates, respectively. Image 1 Highlights • Novel inverted perovskite solar cells (PSCs) with Cu-phthalocyanine and C 60 as HTL and ETL, respectively. • 16.72% efficiency is obtained, which is the highest efficiency of the inverted PSCs employing CuPc as HTL. • 12.96% efficiency is obtained for the flexible device. • Almost no hysteresis is observed. • Cost-effective, easy to prepare and highly stable. [ABSTRACT FROM AUTHOR]

Electron transport layer (ETL), functioning as the electron transportation and extraction layer as well as hole-blocking layer, plays an important role in planar perovskite solar cells (PSCs). Majority of the state-of-the-art PSCs contain a TiO 2 ETL always requiring a high temperature (500 °C) treatment, which is both energy-consuming and incompatible with flexible substrates, thus hindering large-scale application in flexible devices. Here, we demonstrated a low-temperature (70 °C) solution-processed Mg-doped rutile TiO 2 as ETL in planar PSCs, while the thermal-evaporated copper phthalocyanine (CuPc) and doctor-bladed carbon were introduced as the hole transport layer (HTL) and counter electrode, respectively. The as-prepared PSC obtains a 15.73% power conversion efficiency (PCE), which is quite an excellent efficiency among carbon-based planar PSCs, getting an increase by 16% compared to the 13.56% PCE of the pristine TiO 2 -based device. The prominent increment is mainly attributed to the faster charge extraction, better electrical conductivity and suppressed charge recombination of Mg-doped TiO 2 . Besides, using highly stable CuPc and commercial carbon makes the as-prepared PSCs highly durable over 30 days when exposed to the ambient air with a relative humidity of 50%. Since all the processes are conducted under 100 °C, our work paves a way for developing cost-effective and highly stable PSCs compatible with flexible substrates. [ABSTRACT FROM AUTHOR]

SnO 2 electron transport layers (ETLs) had an essential role in the n-i-p structure of perovskite solar cells. Improving the quality of the electron transport layer and enhancing interfacial contacts were key factors in the fabrication of high-performance perovskite solar cells. Therefore, a non-ionic polymeric polyacrylamide (PAM) modified SnO 2 colloidal solution with improved clustering of SnO 2 nanoparticles was presented to form a uniform and dense SnO 2 electron transport layer. The results demonstrated that no pinhole pores were found at the interface where the PAM-modified electron transport layer and the light absorbing layer came into contact, a structure that facilitated carrier transport and reduced carrier recombination at the interface location. Further beneficial effects were revealed by femtosecond Fs-TA measurements and trap of states (tDOS) analysis, where the carrier lifetime τ 2 decreased from 306.7 ps to 137.8 ps and the trap density of states of the film also decreased significantly. Correspondingly, the SnO 2 -PAM device exhibited an optimum efficiency of 21.61 %. Fantastic device stability was obtained due to the interaction of excellent contact at the SnO 2 /FAPbI 3 interface, and 85 % of the initial efficiency was maintained when placed in air for 1000 h for photo-aging tests, thereby improving the stability of FAPbI 3 grains. This method of improving the quality of tin oxide colloidal solutions provided a novel and simple way to prepare efficient perovskite solar cells. [ABSTRACT FROM AUTHOR]