Search

The issue of using nitrogen to eliminate fires in granaries is related to ventilating the grain mass with nitrogen while it is necessary to take into consideration the change in gas concentration. Therefore, the object of this research was the value of the minimum concentration of nitrogen to eliminate the combustion of sunflower grain. It has been proven that in the process of thermal destruction of sunflower grain, the composition of gaseous products of thermal destruction of sunflower grain contains more than 70 % of combustible gases. Namely: carbon monoxide, over 51 %; hydrogen, about 5.7 %; and hydrocarbons with a total concentration of 13.72 %, which provide fire hazardous properties of organic material. Therefore, it should be noted that the release of the amount of combustible gases during pyrolysis requires a reduction in the amount of oxygen in the gasair environment to eliminate fire sites. Obviously, such a mechanism for the decomposition of sunflower grain during pyrolysis is a factor in regulating the extinguishing process, due to which the amount of nitrogen to eliminate combustion increases. Comparison of experimental studies on the composition of gaseous products of thermal destruction of sunflower grain and studies to determine the minimum fire extinguishing concentration of nitrogen, at which combustion was stopped, made it possible to justify the use of nitrogen. Based on the study’s results on the elimination with nitrogen of fire sites of sunflower grain, the values of the minimum fire extinguishing concentration were revealed at extinguishing, about 33.7 % by volume. At the same time, terminating the combustion of sunflower grain occurs with a decrease in the concentration of oxygen in the gas-air environment of about 14 %. The practical significance is the fact that the results obtained for determining the minimum fire extinguishing concentration of nitrogen make it possible to establish operating conditions for granaries when eliminating fire sites. [ABSTRACT FROM AUTHOR]

This paper reports the analysis of compositions for fire protection of wood that established that there are not enough data to explain and describe the process of fire protection and, accordingly, the fire-hazardous properties of wood, in order to protect people. The development and research of a set of properties of fire-resistant materials leads to the design of new types of such materials. The object of this study was a fire-protective two-component intumescent varnish for wood. The essence of the research is to determine the indicators of fire danger of wood, fire-protected by coatings, and the impact exerted on them by the formed heat-insulating layer of coke, making it possible to justify the effectiveness of the fire-retardant coating under the influence of temperature. The volume of fire-retardant and hydrophobic coating has been optimized, which ensures the lowest value of loss of mass by fire-protected wood during thermal action. Its lowest value was determined when using flame retardant in the volume of 589 g/m² and a hydrophobic agent in the volume of 54 g/m². When determining the combustibility of fire-resistant wood, it was established that the temperature of flue gases during tests was no more than 103°C, the length of damage to the sample did not exceed 143 mm. At the same time, the weight loss did not exceed 19 g, and the independent burning of wood did not exceed 23 s. In addition, the wood withstood the surface effect of a heat flow of 35 kW/m2, while surface combustion did not occur, and the value of the coefficient of smoke formation was 432 m²/kg during the smoldering of the fire-proof sample. Unlike wood protection with fire-retardant swelling paint, the fireproof wood with two-component varnish, does not change color and refers to low combustibility materials; it is hard to ignite, dose not spread the flame by surface, with moderate smoke-forming ability. The practical significance is the fact that a certificate of conformity was issued based on the reported results. Thus, there are grounds to assert the possibility of directed adjustment of wood fire protection processes by using coatings that can form a protective layer on the surface of the material [ABSTRACT FROM AUTHOR]

Copyright of Eastern-European Journal of Enterprise Technologies is the property of PC TECHNOLOGY CENTER and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The analysis of fire-protective materials for wooden building structures was carried out and the need to develop reliable methods for studying the process of washing out fire retardants from the surface of the building structure, which is necessary for the creation of new types of fire-protective materials, was established. That is why there arises a need to determine the conditions for the formation of a barrier for washing out and to establish a mechanism for inhibition of moisture transmission to the material. In this regard, a mathematical model was built of washing out fire retardants using a polymeric shell made of organic material as a coating, which makes it possible to estimate the effectiveness of a polymer shell by the amount of the washed-out fire retardant. According to the experimental data and theoretical dependences, the dynamics of the release of fire retardants from the fire-protective layer of the coating was calculated; it did not exceed 1.0 %, and therefore, ensures fire protection of timber. The results of determining the weight loss of the sample under the influence of water indicate the ambiguous impact of the nature of protection on the washout. In particular, this implies the availability of data sufficient for performing a high-quality process of moisture diffusion inhibition and, based on it, detection of the moment, from which a decrease in efficiency of a coating begins. The experimental studies proved that a sample of fire-protected timber after exposure to water for 30 days withstood the influence of a heat flow. In particular, the loss of timber weight after the temperature exposure was less than 6 %, and the temperature of flue gases did not exceed 185 °C. Thus, there is a reason to assert the possibility of directed control of the processes of fire protection of timber through the use of polymer coatings capable of forming a protective layer on the surface of fire-protected material, which inhibits the rate of washing out the fire retardants. [ABSTRACT FROM AUTHOR]