Search

Abstract A 200-W Hall thruster was designed using permanent magnets placing the axial maximum magnetic field outside of the channel, and the anode/gas distributor as an integrated U-shaped structure. A split structure is adopted for the discharge channel to conveniently change the wall material. With the initial conditions that the anode mass flow is maintained at 0.8 mg/s, 1.0 mg/s and 1.2 mg/s over a voltage range of 150–400 V (at 50 V intervals), the discharge properties were determined for the two thruster models with the channel walls composed of graphite and boron nitride (BN). The results demonstrate that under identical operating parameters, the properties of the thruster with the graphite channel walls are similar to the properties of the thruster with the BN channel walls. The maximum difference of the discharge current between the two wall materials is 6.2%; the maximum difference of the thrust and the specific impulse is 3.3%, and that of the anode efficiency is 1.7% (absolute value). These differences are smaller than the corresponding parameter differences observed from changing wall materials in other common Hall thrusters. Highlights • A permanent magnet Hall thruster with graphite channel wall is studied. • Results show differences are smaller with graphite and BN wall. • This study given a new choice of Hall thruster discharge wall to prolong life. [ABSTRACT FROM AUTHOR]

In a 1350-W Hall-effect thruster, in which a technique for pushing down the magnetic field is implemented, a catastrophic discharge phenomenon is identified by varying the magnetic field strength while keeping all other operating parameters constant. According to experiments, before and after the discharge catastrophe, the plume changes from focusing state to a divergent state, and discharge parameters such as discharge current and thrust exhibit noticeable changes. The divergence half-angle of the plume increases from 22° to 46°. The oscillation amplitude and mean values of the discharge current significantly increase from 0.8 A to 4 A and from 4.6 A to 6.3 A, respectively, while the thrust increases from 89.3 mN to 91 mN. Analysis of the experimental results shows that as the maximum magnetic field of the thruster we developed is in the plume region, the acceleration occurs in the plume region and a large number of Xe 2+ ions appear in the plume area, the catastrophic discharge phenomenon observed. [ABSTRACT FROM AUTHOR]

A curved, convex towards the channel bottom magnetic field is an important feature of an advanced Hall thruster that allows confining the plasma flow in the channel center, reducing the divergence angle of the ejected ion beam, and improving the discharge performance. In this article, the discharge behaviour of a Hall thruster in magnetic fields with different degrees of curvature is simulated with a particle‐in‐cell numerical method, and the effect of curved magnetic field on the ion bombardment and wall erosion and the associated mechanisms are studied and analysed. The results show that, as the curvature of the magnetic field increases, the propellant ionization becomes more confined at the channel center, the potential drop inside the channel decreases, and the acceleration region shifts outside the channel, which lead to the attenuation of the ion energy bombarding the wall and the deviation of the bombardment angle from the optimal sputtering angle. Conversely, the ion flux bombarding the wall near the channel exit increases. Nevertheless, the bombardment energy and angle are the dominant factors for the wall erosion, and the wall erosion rate clearly decreases with the increasing curvature of the magnetic field. These findings are closely related to the behaviour of electron conduction under a curved magnetic field; the relevant mechanisms are clarified in this article. [ABSTRACT FROM AUTHOR]

The large height-radius ratio design of the Hall thruster increases the difference of radial distributions of magnetic field and plasma parameters in the channel, so that the optimal discharge effect of the thruster cannot be guaranteed under the symmetrical magnetic field configuration relative to the channel centerline. In this work, the effects of the unsymmetrical magnetic field on discharge characteristics of Hall thruster with large height-radius ratio were studied through experiments and PIC simulations. The results show that the thruster can realize stable discharge in a wide power range under unsymmetrical magnetic fields. Also, the unsymmetrical magnetic field plays a positive role in improving the discharge performance and prolonging the service life of the thruster. The inward-inclined magnetic field can effectively improve the discharge performance of the thruster, and the discharge efficiency can be increased by 1.5% under the rated working condition compared with the symmetrical magnetic field. The advantage in performance is mainly attributed to the improvement of ionization efficiency of propellant. The outward-inclined magnetic field is more conducive to prolong the service life of the thruster, and the peak value of ion power deposition on the inner wall can be reduced by 40% under the rated working condition due to the outward inclination of the ionization zone and the reduction of the radial electric field. However, under unsymmetrical magnetic field, the ionization zone deviates from the channel center, and the high ionization rate zone is more dispersed in distribution, thus leading to the increase in plume divergence angle. This study verifies that the unsymmetrical magnetic field has certain advantages under the structure of large height-radius ratio, which could be used as a guidance for the optimal design of Hall thruster with large height-radius ratio. • Hall thruster can operate in a wide power range under unsymmetrical magnetic fields. • Inward-inclined magnetic field can improve thruster discharge performance. • Outward-inclined magnetic field is conducive to prolong thruster service life. [ABSTRACT FROM AUTHOR]