Search

A novel powered ankle–foot prosthesis is designed. The effect of wearing the novel prosthesis and an energy-storage-and-return (ESAR) foot on lower-limb biomechanics is investigated to preliminarily evaluate the design. With necessary auxiliary materials, a non-amputated subject (a rookie at using prostheses) is recruited to walk on level ground with an ESAR and the novel powered prostheses separately. The results of the stride characteristics, the ground reaction force (GRF) components, kinematics, and kinetics in the sagittal plane are compared. Wearing the powered prosthesis has less prolongation of the gait cycle on the unaffected side than wearing the ESAR foot. Wearing ESAR or proposed powered prostheses influences the GRF, kinematics, and kinetics on the affected and unaffected sides to some extent. Thereinto, the knee moment on the affected side is influenced most. Regarding normal walking as the reference, among the total of 15 indexes, the influences of wearing the proposed powered prosthesis on six indexes on the affected side (ankle's/knee's/hip's angles, hip's moment, and Z- and X-axis GRF components) and five indexes on the unaffected side (ankle's/knee's/hip's angles and ankle's/hip's moments) are slighter than those of wearing the ESAR foot. The influences of wearing the powered prosthesis on two indexes on the unaffected side (knee's moment and X-axis GRF component) are similar to those of wearing the ESAR foot. The greatest improvement of wearing the powered prosthesis is to provide further plantarflexion after reaching the origin of the ankle joint before toe-off, which means that the designed powered device can provide further propulsive power for the lifting of the human body's centre of gravity during walking on level ground. The results demonstrate that wearing the novel powered ankle–foot prosthesis benefits the rookie in recovering the normal gait more than wearing the ESAR foot. [ABSTRACT FROM AUTHOR]

3D printing is the most suitable method to manufacture the frame parts of powered ankle-foot prostheses but the compressive strength of the 3D-printed part needs to be ensured. According to the compression test standard ASTM D695, the effect of infill pattern and density, which is transferred to the mass of the standard specimen, on the compressive strength is investigated with a carbon fiber-reinforced nylon material. With the same infill pattern, specimens with more mass have a higher compressive strength. With the same mass, specimens with triangular fill have a higher compressive strength than those with rectangular and gyroid fills. Compared with specimens with a solid fill, specimens with a triangular fill can also provide more compressive strength in a unit mass. According to the results of standard specimens, following the requirement of strength and lightweight, 41% triangular fill is selected to manufacture the supporting part of a powered ankle-foot prosthesis. Under a compressive load of 1225 N, the strain of the assembly of the standard adaptor and the 3D-printed part is 1.32 ± 0.04%, which can meet the requirement of the design. This study can provide evidence for other 3D-printed applications with the requirement of compressive strength. [ABSTRACT FROM AUTHOR]

A powered transfemoral prosthesis is needed as people with transfemoral amputation show 60 percent extra metabolic cost when compared to people with no amputation. Recently, as illustrated in the literature, the most high-torque robotic knee prosthesis utilize harmonic reducers. Despite the advantage of high reduction ratio and efficiency, the harmonic drive cannot be back-driven. Therefore, the harmonic drive is not an optimal solution for prosthetic systems with direct and indirect contact with the environment. In this paper, we outline an initial design of robotic knee prosthesis. The proposed robotic knee prosthesis consists of BLDC motor, cycloidal gear with reduction ratio 13:1, four-bar mechanism, and timing belt transmission with 4:1 reduction ratio. To optimize the torque transmission and range of motion (RoM), a multiobjective optimization problem must be undertaken. The end-effector motion depends on each bar length in the four-bar mechanism. The four-bar mechanism was optimized using particle swarm optimization (PSO). To complete the optimization, a set of 50 steps was collected using wearable sensors. Then, the data of sagittal plan were processed to identify the target profile for PSO. The prototype's computer-aided manufacturing (CAM) was completed using a MarkTwo 3D printer with carbon fiber composite. The overall design can achieve a maximum torque of 84 N.m. However, the current design lacks the elastic component (no spring is added on the actuator output), which is necessary for a functional prosthesis; this limitation will be addressed in future study. [ABSTRACT FROM AUTHOR]

Planar spiral spring is important for the dimensional miniaturisation of motor-based elastic actuators. However, when the stiffness calculation of the spring arm is based on simple beam bending theory, the results possess substantial errors compared with the stiffness obtained from finite-element analysis (FEA). It deems that the errors arise from the spiral length term in the calculation formula. Two Gaussian process regression models are trained to amend this term in the stiffness calculation of spring arm and complete spring. For the former, 216 spring arms' data sets, including different spiral radiuses, pitches, wrap angles and the stiffness from FEA, are employed for training. The latter engages 180 double-arm springs' data sets, including widths instead of wrap angles. The simulation of five spring arms and five planar spiral springs with arbitrary dimensional parameters verifies that the absolute values of errors between the predicted stiffness and the stiffness from FEA are reduced to be less than 0.5% and 2.8%, respectively. A planar spiral spring for a powered ankle–foot prosthesis is designed and manufactured to verify further, of which the predicted value possesses a 3.25% error compared with the measured stiffness. Therefore, the amendment based on the prediction of trained models is available. [ABSTRACT FROM AUTHOR]

This paper presents the design and evaluation of an in-socket sensory system for a transfemoral prosthetic leg using a set of piezoelectric sensors. The design process includes identifying the optimal mounting configuration of the sensors and determining their best placement. Two experiments were performed separately to address each objective. Results of the experiment suggested that cushion-all with fit size cantilever with elastic foundation should be adopted to mount the sensors on the socket's wall. As for the placement of the sensors, the result suggested that the sensors should be positioned in zig-zag orientation from top to bottom, which can cover all of the most active area on the quadriceps and hamstring muscle groups. With the identified design, the socket was fabricated and instrumented for a transfemoral amputee and the performance of the in-socket sensory system was evaluated. The amputee performed level walking at normal speed on a 5-m straight pathway multiple times while the output voltage signal from each sensor was recorded. The output signals consistency was assessed by calculating the cross correlation, r , within five trials. In order to measure the strength of the correlation matrix of each sensor, the Frobenius norm, \vert \vert A\vert \vert F was calculated. The high norm value for all sensors pattern (\vert \vert A\vert \vert F > 4.5) for quadriceps implies that the mounting and placement of the sensors is most suitable for a consistent and reliable signal. For Hamstring, results inferred that except for the two sensors located on the top most position and the most bottom sensor, the other sensors showed good performance (\vert \vert A\vert \vert F > 4.4 ). Thus, the proposed design of the in-socket sensory system using piezo sensors was proven to be effective for a transfemoral prosthetic leg. [ABSTRACT FROM PUBLISHER]