Search

This article proposes a highly efficient current-fed half-bridge resonant converter over a wide range of the output voltages. By adding a bidirectional switch across center nodes of the voltage doubler and applying corresponding switching modulation, the converter accomplishes almost zero-voltage switching at the turn-off instant under the wide output voltage variations. Moreover, the circuit experiences very little instantaneous reactive current even when the output voltage varies widely. Primary-side duty cycle fixed at 0.5 balances the voltages across the capacitors at the primary side and at the secondary side each irrespective of the output voltage variation; it also limits the voltage stress at the active power components. Therefore, the proposed converter delivers high efficiency and compact component size. We fabricated a 400-W experimental prototype to validate the superior properties of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper details the design and implementation of an efficient 4-kW bidirectional converter with a wide load range, based on a three-phase LCC resonant converter operated in a continuous conduction model, which has a number of advantages pertaining to a bidirectional power supply. The voltage boost-up function yields a high voltage gain without increasing the transformer turn ratio. The high switching frequency, which is achievable by using the soft-switching condition and multiphase operation, decreases the output ripple and helps minimize the size of the output filter, as the requirement for a filter changes after the power flow. Moreover, this reduction in the size of the filters yields economic advantages. In addition, because of the synchronous rectifier operation employed during switching, the conduction loss in the rectifier diode of the proposed converter is low. The direction of the output power can be changed easily, using phase control. The implemented power converter is connected to a 320-V rated generator on one side and 28-V lead-acid batteries on the other side. The functionality of the proposed converter is verified in experiments. We confirmed the high performance of the developed converter in terms of efficiency (92.2%), operable load range (0–12.5 A in step-up, and 0–142 A in step-down), and voltage ripple (0.05%). [ABSTRACT FROM AUTHOR]

This paper presents the design and implementation of a 40-kV, 20-kJ/s high-voltage capacitor charger based on a series/parallel resonant converter. The inclusion of the parallel resonant capacitor component in this circuit results in the production of a trapezoidal resonant current, which reduces conduction loss. This capacitor is practically realized as a part of the balancing network of the high-voltage rectifiers in the secondary side of the circuit. Particular attention in this paper is paid to the high-voltage transformer, which must be carefully designed to provide the required functionality without negative impact on the resonant circuit. A PSpice simulation has been used to prove that the proposed control method for the circuit is valid. This is supported with the experimental results, which verify that the operation of the circuit is as expected and that the converter is able to meet all the design criteria with an efficiency of up to 96%. [ABSTRACT FROM PUBLISHER]

This paper describes the design and implementation of a three-phase resonant converter with low ripple and high control accuracy. Based on a three-phase LCC-type resonant converter—which has advantages of low ripple, high-efficiency, and high-power density compared with a single-phase converter—a high-voltage power supply with low ripple (<0.1%) was designed. In addition to the general merits of an LCC-type resonant converter operating at continuous conduction mode—including soft switching, low conduction loss, and current source characteristics—the proposed scheme uses only one phase under a light-load condition by having different leg designs of the gate drive circuit and snubber parameters. This allows the design to overcome the operational constraints of the general LCC-type resonant converter. The distinctive design of the three-phase converter structure provides high efficiency and low ripple not only during rated operation, but also under light-load conditions. In order to analyze the high performance of the proposed scheme from no load to rated load, a PSPICE simulation was carried out. Comparison results with a conventional LCC-type resonant converter based on a single-phase structure are analyzed from the viewpoints of output ripple, losses, and operable load range. Using the proposed converter, a 20-kV, 20-kW high-voltage dc power supply design and implementation was presented with a superior gate drive circuit. Finally, the superiority of the proposed converter was verified through a simulation and experimental results. It was experimentally confirmed that the developed power supply achieves high performance in terms of efficiency (98%), operable load range (0.5–20 kV), and low ripple (0.05%), with a high power density. [ABSTRACT FROM PUBLISHER]

This paper describes the design, implementation, and comparison of high-voltage capacitor chargers for a solid-state pulsed power modulator (SSPPM). The three different converter topologies are a series resonant converter operating at a discontinuous conduction mode with switching frequency control (SRC_DCM_SFC), a series resonant converter operating at a continuous conduction mode with phase shifted pulse width modulation control (SRC_CCM_PSPWMC), and a series–parallel resonant converter operating at the CCM with SFC (SPRC_CCM_SFC). On the basis of these converter topologies, 10\-kW\rm{average} high-voltage capacitor chargers are designed for the three types of SSPPMs, which have the following maximum output specifications: 1) SRC_DCM_SFC: 60 kV, 300 A, 3 kpps, and 50 \mus; 2) SRC_CCM_PSPWMC: 10 kV, 50 A, 50 kpps, and 10 \mus; and 3) SPRC_CCM_SFC: 40 kV, 150 A, 7 kpps, and 10 \mus. Although the pulse output specifications are different, it is worth comparing the resonant inverter topologies and the control methods from the viewpoint of the losses, control characteristics, and merits and demerits of the high-voltage capacitor chargers. From the analysis and investigation of the three resonant inverters, the design procedure, including the determination of the resonant tank parameters, is provided, which considers the design of the high-voltage capacitor charger. PSPICE simulation is used to elucidate the effects of the resonant tank structure and its parameters, and the resonant current waveform and losses of the Insulated Gate Bipolar Transistor are compared. Finally, experiments for each charger are performed under various load conditions, and the comparison results of the three capacitor chargers, including the conduction and switching losses, control characteristics, and overall efficiency, are discussed in this paper. [ABSTRACT FROM AUTHOR]