Search

Polymer matrix composites (PMCs) are the most used in aerospace fields due to their special mechanical properties coupled with reduced weight. Metallic structures can be manufactured on the surface of PMCs producing hybrid constructions with intriguing characteristics. The cold spray technology (CS) seems to be the best solution for the manufacturing of metallic coatings on polymer-based substrates. However, the last researches on PMCs metallization through CS were carried out without taking into account a proper manufacturing of the substrates. Therefore, the customized manufacturing of PMCs used as substrates for CS deposition represents a crucial aspect to be considered, the target surface should be designed and manufactured to fit better the CS requirements. In this scenario, the Fused Filament Fabrication method (FFF) is the best solution for tailored composites manufacturing. Therefore, this work aims to develop a novel manufacturing route to produce innovative composite structures by using the FFF technology for the 3D-printed polymer-based substrate and the cold spray technology for the 3D-printed metal deposition. The novelty is that, for the first time, the polymer-based substrates will be designed and manufactured “ad hoc” for the cold spray metallization by using the rapid prototyping 3D-printing process successfully integrated with CS technology.

Cold spray deposition, which can be framed in the wider family of additive manufacturing, is a manufacturing technique that is able to produce coatings on diverse types of substrates through the deposition of feedstock powder. As a low-temperature process, cold spray represents a potential solution for the metallization of temperature-sensitive materials, i.e. polymers and polymer matrix composites. The study of the cold spray technology for the metallization of polymers is still in its early stage, and the deposition mechanisms of metals on polymer-based materials are not thoroughly understood yet. On these premises, a review on this topic is needed to systematically depict the actual state of the art and to provide a reliable and well-organized overview discussing all the theories arisen in these years. In summary, this review aims: i) to collect all the available literature and enucleate the most discussed and interesting points (the most prevailing theories regarding the bonding mechanisms, the influence of the different process parameters and the main characteristics of cold-sprayed coating), providing a reliable and well-organized state of the art; ii) to define the open questions and to delineate the directions of future work.

Polymer matrix composites are finding never-ending widespread uses in the last decades, one recent tendency is to metallize their surface to further widen their field of application. Cold-spray deposition is one of the most promising techniques that can be adopted to this aim. Cold-spray deposition on polymers is in its early stage and more experimental work is required to fully understand the phenomena ruling the deposition. In this paper, the results of nanoindentation measurements on cold-spray coatings on various substrates will be presented and discussed. Polypropylene was used as matrix while carbon and glass fibers have been used as reinforcement, both steel and aluminum have been used as feedstock material for the cold-spray deposition. Nanoindentations tests have been then carried out on all the different samples, the influence of the fibers and of the powders sprayed on the behavior of the coatings is discussed in light of the experimental outcomes.

The deposition of steel powders on glass fiber reinforced polymer (GFRP) with the Cold Spray technique is investigated. Metallization of composite materials is still challenging when high-strength and dense powders, such as steel, are used due to excessive erosion of the polymer or disruption of the fibers during the deposition. To overcome these issues, low-pressure cold spray equipment has been used for the experimental campaign shown in this paper. Different coatings were obtained by using nitrogen as the carrier gas and different sets of pressure and standoff distance. Optimization of the process parameters, including the stratification of the laminate, has been carried out. Results of an initial study of the feasibility of the process and the influence of the different chosen spray conditions are exposed. In particular, the bonding mechanisms of steel powders and their morphology are discussed.

Cold spray deposition of aluminum powders on polyethylene reinforced with glass fibers has been studied. Different processing conditions, including different stratifications of the fiber-reinforced polymer used as a substrate, have been investigated to better understand the deposition mechanism. The experimental campaign has been conceived and tailored to highlight the influence of several process parameters on the deposition of the first layer of particles. The results obtained allowed to highlight and clarify the influence of standoff distance and gas pressure and also gave some insights concerning the effect of the substrate stratification. Guidelines regarding the design of the manufacturing process have been also released.

Metallization is a common strategy employed to enhance the electrical and thermal conductivity of polymer matrix composite materials. Nevertheless, metallic deposition on polymer-based materials is challenging due to the inherent limitations related to high temperature exposure of the substrate. In this article, a new technique for the manufacturing of composite laminates and the subsequent metallization by cold spraying of metallic powder is presented. The composite manufacturing route is based on the production of thermoplastic-thermoset hybrid substrates and consisted of two main stages: in the first stage the partial impregnation of a reinforcement textile by a thermoplastic film was promoted by hot pressing compaction. Afterwards, the prepared lamina was vacuum bagged with other reinforcing layers and impregnated by the thermoset catalyzed resin by a vacuum infusion process. Finally, the thermoset and thermoplastic layers were co-cured to increase the adhesion of the substrate with the thermoplastic film. The metallization of composite laminate was obtained through the cold spraying technique, depositing powders on the thermoplastic surface layer. The effect of processing parameters on the coating deposition, quality and microstructure was reported and discussed.

Recently, the growing attraction to the development of new eco-sustainable composite materials is driving the research interest toward the replacement of synthetic reinforcing fibres with natural ones and exploiting the inherent recyclability of thermoplastic resins even for uses in which thermosetting matrices are well consolidated (e.g. naval and aeronautical fields). Among the natural fibres, a growing interest of the research is addressed to basalt fibres. Focusing the attention on thermoplastic composites, many experimental findings already available in literature highlight the outstanding mechanical properties of composite materials including basalt fibres and their potentiality concerning glass ones. On the other hand, some issues are related to the surface properties of the bio-laminates: in particular, the wear ones, the flame resistance and the aesthetic appearance have to be improved to extend the application fields of these materials. Aiming to these goals, this paper deals with the study of the deposition ofaluminium coating through cold spray process on polypropylene/basalt fabric composite laminates. The specimens were obtained by film stacking, and compression moulding technology and their performances were studied in terms of low-velocity impact behaviour, considering the influence of the surface modification with the aluminium coating. The results obtained from the reference laminates and the coated ones are compared in terms of impact parameters: the aluminium deposition seems to affect the damage mechanism propagation even if the impact response seems to be similar in both conditions.

In this activity, customized panels for the CS deposition have been produced and aluminium has been deposited using air as a carrier gas. The custom-made panels were made with different matrix thicknesses on the surface in order to point out the influence of the fibres in the deposition and to study the feasibility and the growth of the coating. The polymer chosen for the matrix is polypropylene, widely used in the automotive sector, while for the reinforcements glass fibres have been used. Different process parameters have been examined in order to point out the influence of temperature, stand-off distance and pressure chosen, on the compaction and densification of the coating produced. In addition, morphological investigations were performed to further characterize the coatings deposited. It has been noticed that aluminium powders can be effectively deposited on polypropylene panels, leading to significantly better results when the thickness of the matrix is ​​sufficient to prevent the powders bouncing elastically on the fibres, while benefiting from the stiffening effect of the latter.