Search

This work describes the fabrication of a novel electroconductive membrane made of Ti3C2Tx (MXene) nanosheet coating through a one‐step pressure‐assisted technique. Ti3C2‐MXene is firmly attached over a polyamide–imide (PAI) microfilter by employing a binder composed of carboxymethyl cellulose (CMC)/glutaraldehyde (GA). Through coating a proper amount of multilayer Ti3C2‐MXene, the electrical conductivity of 174 ± 0.16 S m−1 is achieved. The rejection rates of reactive red 120 (RR120), reactive black (RB), and methyl orange (MO) by the pristine PAI membrane are 45.2%, 40.81%, and 33.65%, respectively. However, rejection rates significantly improve with the Ti3C2 MXene coating to over 99.71%, 97.95%, and 68.91% for RR120, RB, and MO. Applying a 4 V cathodic potential resulted in a flux recovery ratio (FRR) of 99.83% and a flux decline rate (FDR) of less than 1% during humic acid (HA) filtration. Without applying voltage, the MXene‐coated membrane shows an FRR and FDR of 92.51% and 45.56%, respectively. Surface energy analysis reveals strong repulsive interactions between foulants and the membrane surface. Moreover, the surface free energy indicates that foulants such as sodium alginate (SA) and bovine serum albumin (BSA) exhibit stronger adhesion to the membrane than HA, consistent with the fouling experiment results. [ABSTRACT FROM AUTHOR]

MXenes have demonstrated potential for various applications owing to their tunable surface chemistry and metallic conductivity. However, high temperatures can accelerate MXene film oxidation in air. Understanding the mechanisms of MXene oxidation at elevated temperatures, which is still limited, is critical in improving their thermal stability for high-temperature applications. Here, we demonstrate that Ti3C2Tx MXene monoflakes have exceptional thermal stability at temperatures up to 600 °C in air, while multiflakes readily oxidize in air at 300 °C. Density functional theory calculations indicate that confined water between Ti3C2Tx flakes has higher removal energy than surface water and can thus persist to higher temperatures, leading to oxidation. We demonstrate that the amount of confined water correlates with the degree of oxidation in stacked flakes. Confined water can be fully removed by vacuum annealing Ti3C2Tx films at 600 °C, resulting in substantial stability improvement in multiflake films (can withstand 600 °C in air). These findings provide fundamental insights into the kinetics of confined water and its role in Ti3C2Tx oxidation. This work enables the use of stable monoflake MXenes in high-temperature applications and provides guidelines for proper vacuum annealing of multiflake films to enhance their stability. [ABSTRACT FROM AUTHOR]

2D rare-earth metal carbides (MXenes) are attractive due to their novel electronic and magnetic properties and their potential as scalable 2D magnets. In this study, we used density functional theory with the Hubbard U correction to characterize the structure, termination, and magnetism in an out-of-plane ordered rare-earth containing M3C2Tx MXene, Mo2NdC2T2 (T = O or OH). We investigated the effect of the U parameter on the stability and magnetism of two possible termination sites: the hollow sites aligned with the inner Nd atoms (Nd-hollow sites) and those aligned with the closest C atoms (C-hollow sites). We found that increasing UMo stabilized the Nd hollow sites, which minimized electrostatic repulsion between C and O atoms. Using UMo = 3.0 eV and UNd = 5.6 eV, obtained via the linear response method, we found that the energetically preferred termination site was C-hollow in Mo2NdC2O2 and Nd-hollow in Mo2NdC2(OH)2. Regardless of termination and the Hubbard U value, we found Mo2NdC2O2 and Mo2NdC2(OH)2 to be magnetic. The C-hollow termination resulted in ferromagnetic states for all Hubbard U tested with no magnetic moment in Mo. In the case of Nd-hollow, Mo became magnetic for UMo ≥ 4 eV. The difference of Mo magnetism in Nd-hollow and C-hollow was explained by crystal field splitting of the Mo d orbital caused by a distorted ligand. [ABSTRACT FROM AUTHOR]

The recent progress on the liquid crystalline (LC) dispersion of two‐dimensional (2D) transition metal carbides (MXenes) has propelled this unique nanomaterial into a realm of high‐performance architectures, such as films and fibers. Additionally, compared to architectures made from typical non‐LC dispersions, those derived from LC MXene possess tunable ion transport routes and enhanced conductivity and physical properties, demonstrating great potential for a wide range of applications, such as electronic displays, smart glasses, and thermal camouflage devices. This review provides an overview of the progress achieved in the production and processing of LC MXenes, including critical discussions on satisfying the required conditions for LC formation. It also highlights how acquiring LC MXenes has broadened the current solution‐based manufacturing paradigm of MXene‐based architectures, resulting in unprecedented performances in their conventional applications (e.g., energy storage and strain sensing) and in their emerging uses (e.g., tribology). Opportunities for innovation and foreseen challenges are also discussed, offering future research directions on how to further benefit from the exciting potential of LC MXenes with the aim of promoting their widespread use in designing and manufacturing advanced materials and applications. [ABSTRACT FROM AUTHOR]

For better charge storage and rate performance, supercapacitors need unique electrode materials and design architectures. Recent interest in metal–organic frameworks (MOFs) stems from their chemical compatibility with host materials and the abundance of active sites. However, their direct use as electrode materials has been difficult due to their limited electrical conductivity and excessive agglomeration, making them poor electrochemical performers. To solve these problems and boost the performance, we synthesized a nanoporous carbon-based electrode with metallic cobalt nanoparticles and MXenes. The electrode material is a zeolite-imidazole framework (ZIF)-67-derived cobalt-based nanoporous carbon nanotube (CNT) composite produced via in situ growth on Ti3C2Tx MXene flakes by pyrolysis under inert conditions. In situ synthesized porous CNTs add porosity and interconnecting channels to the MXenes providing increased sheet ion transport and diffusion, improving the electrochemical performance. This lowered the charge resistance to 3.73 Ω and enhanced the MXene nanosheet Bode phase angle. In an aqueous acidic electrolyte, the MXene-nanoporous CNT composite exhibited a nominal capacitance of 1605 F/g and 94.5% charge retention after 5000 cycles. [ABSTRACT FROM AUTHOR]

MXenes, a family of 2D transition‐metal carbides and nitrides, have excellent electrical conductivity and unique optical properties. However, MXenes oxidize in ambient conditions, which is accelerated upon heating. Intercalation of water also causes hydrolysis accelerating oxidation. Developing new tools to readily characterize MXenes' thermal stability can enable deeper insights into their structure–property relationships. Here, in situ spectroscopic ellipsometry (SE) is employed to characterize the optical properties of three types of MXenes (Ti3C2Tx, Mo2TiC2Tx, and Ti2CTx) with varied composition and atomistic structures to investigate their thermal degradation upon heating under ambient environment. It is demonstrated that changes in MXene extinction and optical conductivity in the visible and near‐IR regions correlate well with the amount of intercalated water and hydroxyl termination groups and the degree of oxidation, measured using thermogravimetric analysis. Among the three MXenes, Ti3C2Tx and Ti2CTx, respectively, have the highest and lowest thermal stability, indicating the role of transition‐metal type, synthesis route, and the number of atomic layers in MXene flakes. These findings demonstrate the utility of SE as a powerful in situ technique for rapid structure–property relationship studies paving the way for the further design, fabrication, and property optimization of novel MXene materials. [ABSTRACT FROM AUTHOR]

Rechargeable magnesium batteries (RMBs) are promising next‐generation low‐cost and high‐energy devices. Among all RMBs, anode‐free magnesium metal batteries that use in situ magnesium‐plated current collectors as negative electrodes can afford optimal energy densities. However, anode‐free magnesium metal batteries have remained elusive so far, as their practical application is plagued by low Mg plating/stripping efficiency due to nonuniform Mg deposition on conventional anode current collectors. Herein, for the first time, an anode‐free Mg‐metal battery is developed by employing a 3D MXene (Ti3C2Tx) film with horizontal Mg electrodeposition. The magnesiophilic oxygen and reactive fluorine terminations in MXene enable an enriched local magnesium‐ion concentration and a durable magnesium fluoride‐rich solid electrolyte interphase on the Ti3C2Tx film surface. Meanwhile, Ti3C2Tx MXene exhibits a high lattice geometrical fit with Mg (≈96%) to guide the horizontal electrodeposition of Mg. Consequently, the developed Ti3C2Tx film achieves reversible Mg plating/stripping with high Coulombic efficiencies (>99.4%) at high‐current‐density (5.0 mA cm−2) and high‐Mg‐utilization (50%) conditions. When this Ti3C2Tx film is coupled with a pre‐magnesized Mo6S8 cathode, the anode‐free Mg‐metal full‐cell prototype exhibits a volumetric energy density five times higher than its standard Mg‐metal counterpart. This work provides insights into the rational design of anode current collectors to guide horizontal Mg electrodeposition for anode‐free Mg metal batteries. [ABSTRACT FROM AUTHOR]

Magnesium metal batteries are promising candidates for next‐generation high‐energy‐density and low‐cost energy storage systems. Their application, however, is precluded by infinite relative volume changes and inevitable side reactions of Mg metal anodes. These issues become more pronounced at large areal capacities that are required for practical batteries. Herein, for the first time, double‐transition‐metal MXene films are developed to promote deeply rechargeable magnesium metal batteries using Mo2Ti2C3 as a representative example. The freestanding Mo2Ti2C3 films, which are prepared using a simple vacuum filtration method, possess good electronic conductivity, unique surface chemistry, and high mechanical modulus. These superior electro‐chemo‐mechanical merits of Mo2Ti2C3 films help to accelerate electrons/ions transfer, suppress electrolyte decomposition and dead Mg formation, as well as maintain electrode structural integrity during long‐term and large‐capacity operation. As a result, the as‐developed Mo2Ti2C3 films exhibit reversible Mg plating/stripping with high Coulombic efficiency of 99.3% at a record‐high capacity of 15 mAh cm−2. This work not only sheds innovative insights into current collector design for deeply cyclable Mg metal anodes, but also paves the way for the application of double‐transition‐metal MXene materials in other alkali and alkaline earth metal batteries. [ABSTRACT FROM AUTHOR]