Search

Average yield of maize (Zea maysL.) in Mozambique is low, mainly due to low use of inputs in agriculture, high seasonal rainfall variability and inadequate soil preparation. A study conducted in two summer crop seasons (November–March 2012/2013 and 2013/2014) examined the impact of three tillage methods (hand hoeing, strip tillage and conventional tillage), two fertiliser levels (0 and 40% N) and two water supply regimes (rainfed and irrigated) on maize root development and grain yield on a sandy soil in a semi-arid region of Mozambique. Tillage had a major effect on soil penetration resistance, but little effect on root growth and limited effect on yield. Thus, there appears to be little need for loosening on this soil. There was also no interaction between tillage and the other experimental factors, meaning that tillage system can be chosen irrespective of fertiliser and water supply. Irrigation had the largest impact on root and shoot growth and crop yield, increasing yield in season 2 from 670 to 4780 kg ha–1.There was a very strong interaction between fertiliser and water supply, with no yield increase for fertiliser in the rainfed treatment, while combined with irrigation it increased yield by 1590 kg ha–1in season 1 and 1840 kg ha–1in season 2. Thus, for the conditions studied here, it was rational to add fertiliser only in combination with irrigation and not in a rainfed system. [ABSTRACT FROM AUTHOR]

Several previous field studies in temperate regions have shown decreased soil respiration after conventional tillage compared with reduced or no-tillage treatments. Whether this decrease is due to differences in plant residue distribution or changes in soil structure following tillage remains an open question. This study investigated (1) the effects of residue management and incorporation depth on soil respiration and (2) biological activity in different post-tillage aggregates representing the actual size and distribution of aggregates observed in the tilled layer. The study was conducted within a long-term tillage experiment on a clay soil ( Eutric Cambisol) in Uppsala, Sweden. After 38 y, four replicate plots in two long-term treatments (moldboard plowing (MP) and shallow tillage (ST)) were split into three subplots. These were then used for a short-term trial in which crop residues were either removed, left on the surface or incorporated to about 6 cm depth (ST) or at 20 cm depth (MP). Soil respiration, soil temperature, and water content were monitored during a 10-d period after tillage treatment. Respiration from aggregates of different sizes produced by ST and MP was also measured at constant water potential and temperature in the laboratory. The results showed that MP decreased short-term soil respiration compared with ST or no tillage. Small aggregates (< 16 mm) were biologically most active, irrespective of tillage method, but due to their low proportion of total soil mass they contributed < 1.5% to total respiration from the tilled layer. Differences in respiration between tillage treatments were found to be attributable to indirect effects on soil moisture and temperature profiles and the depth distribution of crop residues, rather than to physical disturbance of the soil. [ABSTRACT FROM AUTHOR]

Highlights: [•] More than 1000 experimental years were included in the analysis of yield data. [•] Crop yield on average 10% lower for no-tillage compared to mouldboard ploughing. [•] Crop yield on average 2% lower for shallow tillage compared to mouldboard ploughing. [•] Dicots were more sensitive to compaction than cereals. [•] Winter wheat yield in reduced tillage was much affected by preceding crop. [ABSTRACT FROM AUTHOR]

Delaying tillage and incorporation of arable crop residues in autumn may limit accumulation of soil mineral nitrogen (SMN) and reduce nitrogen (N) leaching. However, on clay soils, high water content during late tillage can impair soil structure and fertility. This study investigated the effects of tillage timing on SMN (0–90 cm depth), soil physical properties in the topsoil and yield in two Swedish clay soils differing in clay content. SMN generally increased during autumn and also with earlier tillage. On a heavy clay soil (Ultuna; ∼60% clay), SMN increased throughout winter until spring and the amount of N leached was probably small. In contrast, on a clay loam soil in southernmost Sweden (Rydsgård; ∼35% clay), SMN decreased during winter by up to 26 kg ha−1. In general, measured soil water content (w) was lower than 0.9 × plastic limit (PL) at the time of early tillage (mouldboard ploughing or stubble cultivation), while it exceeded 0.9 PL at the time of normal and late tillage. The proportion of small aggregates produced by tillage was negatively correlated to relative soil water content at the time of tillage (w/PL). Conventional methods to determine soil physical qualities (bulk density, saturated hydraulic conductivity, aggregate tensile strength) did not show any clear differences between treatments. However, plant emergence and yield were significantly reduced after late compared with early tillage at Ultuna, a trend that has persisted from 2000 until the present. These results suggest that the suitability of delayed autumn tillage as a means to reduce SMN accumulation and N leaching varies between Swedish clay soils. A reduction in N leaching can be achieved on lighter clay soils in warmer and moister areas, whereas the effects may be small on heavier clay soils in central Sweden, where repeated late tillage carries a risk of yield reduction. [ABSTRACT FROM AUTHOR]

The effects of seedbed properties on emergence of various crops were studied in a series of experiments. Results for crops with seeds weighing <7 mg are reported here. The experiments were carried out in shallow plastic boxes placed directly on the ground in the field. Small seeds require shallow sowing, which is a great disadvantage in the event of dry weather after sowing, particularly on clay and clay loam soils, where the upper 3-cm soil layer quickly dries to wilting point. Nevertheless, good emergence of crops with seeds weighing 2–7 mg (white mustard,Sinapis albaL., oilseed rape,Brassica rapaL., Metzg., sugar beet,Beta vulgarisL. and red clover,Trifolium pratenseL.) was often obtained when the seed was placed at about 3-cm depth directly on a firm basal layer with >6% plant-available water and covered by soil dominated by aggregates <5 mm. Cruciferous crops germinated most rapidly, which facilitated emergence from shallow depth. Sowing could be slightly shallower in coarse-textured than in fine-textured soils, since the former soils dry less rapidly to below wilting point. For timothy (Phleum pratenseL.) with seeds weighing about 0.5 mg and requiring a sowing depth <2.5 cm, it was impossible to design a seedbed that eliminated the risk of poor emergence in dry weather. Firming of the seedbed after sowing favoured emergence only in initially dry seedbeds. The risk of poor emergence because of surface layer hardening was minimised by placing seeds at a depth and in seedbed conditions that promoted the fastest possible emergence. [ABSTRACT FROM PUBLISHER]

Abstract: Excessive soil compaction can reduce crop growth, but compaction can also have positive effects, e.g. increasing soil unsaturated hydraulic conductivity and thereby the capillary flow of water and nutrients to seeds and plants. There may thus be an optimum state of compactness for plant growth. This study examined the effect of different levels of compaction on sugar beet growth and sugar yield in a total of 10 field experiments performed during 2006–2008, mainly on sandy loams (Eutric Cambisols). In most cases, the soil had been mouldboard-ploughed in autumn. A newly constructed sugar beet seed drill with press wheels was used to create different levels of compaction directly around the seed. Greater compaction was achieved by 1 or 3 passes by tractor wheels over the soil. The actual degree of soil compaction was determined by measuring bulk density at 5–10cm depth and penetration resistance to 30 or 35cm depth. Crop growth was determined by measuring root and plant biomass in mid-June and final sugar beet yield. The concentration of plant nutrients in sugar beet foliage was also determined. Two additional experiments in 2009 examined different levels of traffic in combination with mouldboard ploughing or chisel ploughing to 10 or 20cm depth. On average, one pass with a tractor wheel increased yield compared with uncompacted soil, but increasing the compaction by press wheels on the seed drill had little effect on yield. In most cases, even three passes with tractor wheels had no harmful effect on sugar yield. The effect of traffic on nutrient concentrations in the plant was also very small. In one experiment, shallow tillage with a chisel plough lowered yield compared with mouldboard ploughing. There was also an interaction between the effects of primary tillage and compaction in the spring, with more negative effects after shallow tillage. Overall, the sugar beet crop was relatively insensitive to different levels of traffic applied at the time of sowing. The results indicate that the risk of yield losses due to compaction caused by normal traffic after autumn ploughing is low. However with ploughless tillage, soil bulk density may be too high for optimal growth regardless of traffic during seedbed preparation. [Copyright &y& Elsevier]

Rapid, uniform crop establishment is a precondition for efficient crop production. In order to develop guidelines for seedbed preparation and sowing, extensive experiments were carried out in plastic boxes placed in the field directly on the ground for studies of the effects of seedbed properties on crop emergence. This paper deals with the effects on emergence of cereals caused by surface-layer hardening, induced by simulated rainfall (irrigation) after sowing followed by dry weather. The experimental crop was spring barley (Hordeum vulgare L.). Soils for the experiments (Eutric Cambisols, silt loam or clay loam in most cases) were collected from the surface layer of farm fields in various parts of Sweden. On soils with high silt content, irrigation after sowing often caused slumping and subsequent hardening of the whole seedbed. On clay soils, usually only a shallow surface crust formed. The earliest irrigation had the most negative effects on crop emergence. On a silt loam soil with unstable structure, irrigation with only 5 mm reduced emergence to under 20%. Later or heavier irrigation was often less negative, as it allowed the plants to emerge before the surface layer dried and hardened. Deep sowing greatly increased the negative effects on emergence, whereas soil aggregate size usually had negligible effects. It was concluded that when sowing in practice, seedbed preparation and sowing depth should be chosen to promote the fastest possible emergence. Sowing immediately before rain should be avoided, as should shallow sowing that requires rain for the seed to germinate. [ABSTRACT FROM AUTHOR]

We compared earthworm density, depth distribution and species composition in three soil cultivation experiments including the treatments ploughless tillage and mouldboard ploughing. Sampling was done in September 2005 and for one experiment also in 1994. By yearly sampling 1995–2005, earthworms in an energy forest of Salix viminalis were compared with those in an adjacent arable field. Sampling method was digging of soil blocks and hand sorting and formalin sampling in one cultivation experiment. Both methods were used in the energy forest and arable land comparison. In two soil cultivation experiments, highest abundances or biomass were found in ploughless tillage. Earthworm density was higher in the upper 10 cm, especially in the ploughless tillage. Earthworm density was significantly higher in the energy forest than in the arable field. Formalin sampling revealed c. 36% of the earthworm numbers found by digging in the energy forest and gave almost no earthworms in the arable field. In all treatments with soil cultivation, species living and feeding in the rhizosphere and soil dominated. One such species, Allolobophora chlorotica, was more abundant under mouldboard ploughing than ploughless tillage. Lumbricus terrestris, browsing on the surface and producing deep vertical burrows, was more common in the ploughless tillage. Species living and feeding close to the soil surface were almost only found in the energy forest, which had not been soil cultivated since 1984. The findings support earlier studies pointing out possibilities to encourage earthworms by reduced soil cultivation. This is one of the first published studies that followed earthworm populations in an energy forest plantation during several years. Explanation of earthworm reactions to management and environmental impacts should be done with consideration of the ecology of species or species groups. Earthworm sampling by formalin must always be interpreted with caution and calibrated by digging and hand-sorting sampling. [ABSTRACT FROM AUTHOR]

For studies of the effects of seedbed properties on crop emergence, experiments were carried out in shallow plastic boxes. In some experiments, it was examined whether rainfall after sowing could cause oxygen deficiency in the seedbed sufficiently severe to hamper emergence. Crops studied were barley (Hordeum vulgare L.), wheat (Triticum aestivum L.), oilseed rape (Brassica napus var. oleifera, L., Metzg.) and pea (Pisum sativum L.). For harmful oxygen deficiency to develop it appeared that rainfall would need to cause structural collapse of the surface layer followed by continuously wet weather accompanied by slow drainage and high oxygen consumption in the soil; in the experiments the latter was achieved by large amounts of easily decomposable organic matter. It was concluded that such conditions are rare in the field. Therefore, unless rainfall after sowing generates surface water for an extended period, the poor crop emergence often observed after such rainfall is nearly always caused not by oxygen deficiency, but by surface layer hardening when this layer dries. [ABSTRACT FROM PUBLISHER]

Extensive experiments were carried out in shallow plastic boxes placed directly on the ground in the field to study the effects of seedbed properties on the emergence of various crops in a cool temperate climate. In a group of experiments with barley (Hordeum vulgare L.), we studied the effects on crop emergence of firming (slight compaction) of the seedbed, simulating the recompacting effects of rolling after sowing or press wheels on the seed coulters. Most of the experiments were carried out without irrigation after sowing. The firming usually had a slightly positive effect on emergence when the water content in the surface layer at sowing was below the wilting point. When the water content in the surface layer was higher, firming often reduced emergence drastically, particularly with deep sowing and in coarse-textured soils. The main reason for negative effects was harmful hardening of the surface layer when the more firm seedbed gradually dried out. When irrigation kept the seedbed continuously moist, the negative effect of firming was almost eliminated. Very high initial water content in the basal layer tended to delay surface layer drying and hardening, and to reduce the negative effect of firming. Firming only slightly influenced the evaporative water losses from the soil. In contrast to the results presented here, previous field trials with cereals have usually resulted in more positive effects of rolling after sowing. This indicates that other effects than firming, such as modification of sowing depth and reshaping of the soil surface, are other important effects of rolling. [ABSTRACT FROM PUBLISHER]

Rapid and uniform crop establishment is a prerequisite for efficient crop production and minimal environmental impact. Extensive experiments were carried out in shallow plastic boxes placed in the field directly on the ground for studies of the effects of seedbed properties on emergence of small-grain cereal crops in a cool, temperate climate. This paper presents studies of the seedbed as a protective layer against evaporation and the requirements for good emergence under dry weather conditions. Without rainfall after sowing, nearly complete emergence of barley (Hordeum vulgare L.) was obtained, when rapidly germinating seed was placed on a moderately compacted basal layer containing at least 5% (w/w) plant-available water and covered by a 4 cm deep surface layer consisting of aggregates < 5 mm. This applied even when initial water content in the surface layer was below the wilting point and potential evaporation was high. If the soil at 4 cm depth is drier or if a sufficiently fine seedbed cannot be obtained, then seedbed and sowing depth should be somewhat greater, and if the soil is wetter, then the depth may be smaller. There were only small differences in emergence between surface layers consisting of aggregates < 2 mm, 2-4 mm or 2-5 mm, or dominated by these aggregate fractions, but when the surface layer consisted of coarser aggregates, emergence was usually much lower. Determinations of water losses from the soil during the experimental period showed that the differences in emergence were caused by differences in efficiency of the seedbed to control evaporation. The results indicate that, in an initially wet soil, it is always possible to find a time and method for seedbed preparation and sowing that lead to good emergence of small-grain cereal crops, even with a lengthy period without rainfall after sowing. [ABSTRACT FROM AUTHOR]

Rapid and uniform crop establishment is a prerequisite for efficient crop production and minimal environmental impact. Experiments were carried out in shallow plastic boxes placed directly on the ground in the field for studies of the effects of seedbed properties on emergence of various crops. This paper presents an analysis of the time required for germination and emergence under near-optimal seedbed conditions. The crops studied were barley, oats, wheat, pea, rape seed, white mustard, sugar beet, red clover and timothy. The time required for germination generally increased with size of the seeds, presumably because larger seeds needed more water to initiate germination. This applied both when comparing different crops and different seed sizes of the same crop. However, considerable differences occurred between seed lots of the same crop and there were greater differences between seed lots of the same crop than between the three small grain crops studied. Growth rate of the seedlings generally increased with seed size, presumably because of increased energy content in the seed. Consequently, the most rapid emergence was obtained from small seeds at shallow sowing and from large seeds at deep sowing. The crops studied had a minimum temperature for germination and seedling growth close to 0 °C. Under optimal seedbed conditions, thermal time required for 50% germination of barley was typically about 65 °C days over this base temperature and for seedling growth about 6 °C days cm-1. From 4 cm sowing depth, about 80 °C days were required for emergence but with considerable variations between seed lots. For rape seed or white mustard about 40 °C days were required for germination and about 8 °C days cm-1 for the seedling growth. [ABSTRACT FROM AUTHOR]

Abstract: The energy efficiency of different implements and tillage systems for winter wheat in Sweden was examined. Mouldboard ploughing was compared with different ploughless tillage systems (chisel plough, disc, disc-press) and direct drilling on a clay and a silt loam soil during three years. Fuel consumption was measured for all tillage operations, including seedbed preparation and sowing. Energy balances were calculated, based on the direct and indirect use of fossil fuels in crop production. Specific draught (draught per cross-sectional area of soil) was highest for the disc-press implement, while mouldboard ploughing gave the lowest specific surface (surface area per kg soil). Total energy requirement for tillage ranged from 0.6 to 2.8GJha−1 on the clay soil and 0.5 to 1.5GJha−1 on the silt loam. Yield of winter wheat in the ploughless tillage and mouldboard ploughing systems was similar when oats or barley were grown as preceding crops. Growing winter wheat after winter wheat caused yield losses in treatments with reduced tillage intensity, especially direct drilling. Overall energy use in tillage as a proportion of total energy use for crop production ranged from 5% for direct drilling on the silt loam soil to 25% for mouldboard ploughing on the clay. The energy input in tillage was low compared with the energy in the harvested crop and thus energy efficiency, expressed as energy gain, depended mainly on crop yield and not on tillage intensity. For Swedish conditions, a small increase in energy gain might be expected for ploughless tillage compared with mouldboard ploughing when winter wheat is grown with a good preceding crop, but a lower energy gain when winter wheat is grown after winter wheat. [ABSTRACT FROM AUTHOR]

Abstract: Tillage experiments were carried out in order to study the effect of water content on the aggregate size distribution produced by tillage, and to investigate the relationship between the soil structures produced by tillage and Dexter''s index of soil physical quality, S. Tillage with a mouldboard plough was done on four different soils over a range of naturally occurring water contents. The aggregate size distribution and the specific surface area produced by tillage were obtained by sieving. We define the optimum water content for tillage, θ OPT, as the water content at which the specific surface area of the aggregates produced is maximum. This is consistent with the water content at which the amount of small aggregates produced is greatest and the proportion of clods produced is smallest. For the four investigated soils, θ OPT was found to be close to the water content at the inflection point of the water retention curve, and in the vicinity of 0.8θ PL (where θ PL is the lower plastic limit). At water contents either lower or higher than θ OPT, the specific surface area produced was smaller. The specific surface area produced at θ OPT was found to be strongly correlated with the index of soil physical quality, S. The specific surface area produced is larger the greater S, i.e. the better the soil physical quality. Consistently, the proportion of small aggregates produced at θ OPT is larger and the proportion of clods produced at θ OPT smaller, the greater S. No clods (>50mm) are produced on soils with good physical quality. [Copyright &y& Elsevier]

Abstract: Soil water content during tillage can have a large impact on soil properties and tillage outcome. Measurement of soil relief in relation to fixed elevation points provides a non-destructive method of monitoring loosening/compacting processes during the year. The main objective of this study was to determine the effect of soil water content during primary tillage on soil physical properties. The treatments included mouldboard and chisel ploughing of a clay soil on three occasions in the autumn, with gradually increasing water content (0.76, 0.91 and 1.01×plastic limit). Soil surface height was measured by laser within a 0.64m2 area from fixed steel plates after each tillage occasion, and before and after seedbed preparation in the following spring. The measurements of surface height were compared with measurements of other soil physical properties, such as bulk density, saturated hydraulic conductivity and seedbed properties. Tillage at the lowest water content (0.76×plastic limit) produced the greatest proportion of small aggregates, and generally the most favourable soil conditions for crop growth. Soil loosening, as measured by increase in soil height during primary tillage, was highest for mouldboard ploughing and for tillage at the lowest water content. Differences between tillage treatments decreased with time, but were still significant after sowing in the spring. Natural consolidation during winter was smaller than the compaction during seedbed preparation in the spring. No significant differences in bulk density were found between treatments, and thus soil surface height was a more sensitive parameter than bulk density determined by core sampling to detect differences between treatments. Late tillage under wet conditions caused a greater roughness of the soil surface and the seedbed base, which was also found in the traditional seedbed investigation. The effect of tillage time on seedbed properties also resulted in a lower number of emerged plants in later tillage treatments. The laser measurements were effective for studying changes in soil structure over time. The results emphasize the need to determine changes in soil physical properties for different tillage systems over time in order to model soil processes. [Copyright &y& Elsevier]

In this paper we describe the susceptibility of Swedish subsoils to compaction and discuss strategies for prevention of traffic-induced subsoil compaction against the background of experiences from wheeling experiments conducted in Sweden during recent years. The susceptibility of Swedish subsoils to compaction must be considered high because subsoils are often wet during field operations and machinery with high wheel loads is used. The risk of subsoil compaction could be reduced by technical solutions, such as the use of dual and tandem wheels instead of single wheels, low tyre inflation pressure or tracks. However, each of these solutions has its limitations. Results from several wheeling experiments on different soils indicate that residual deformations occur even when the applied stress is lower than the precompression stress. Hence, soil compaction could not be avoided completely by limiting the applied stress to the precompression stress. [ABSTRACT FROM AUTHOR]

Abstract: The objective of the present study was to measure the specific draught (force per cross-sectional area of worked soil) and energy use for soil fragmentation for different tillage implements and soil conditions. Draught was calculated from measurements of fuel consumption and speed during tillage with a mouldboard plough and a chisel plough set to working depths of 13, 17 and 21cm, and a disc harrow. Tillage was carried out at three different water contents (“Wet”, “Moist” and “Dry”) on two sites. The average working depth was calculated from weighing the loose soil within a 0.25-m2 frame. Specific area of the soil was determined by sieving. Soil strength was measured in situ using a shear vane and a penetrometer. Average working depth was much less than the set working depth for the chisel plough. Specific draught was generally the lowest for the mouldboard plough and the highest for the chisel plough, and increased with decreasing soil water content. The specific draught was strongly correlated to soil cohesion, but not to penetration resistance. The proportion of coarse aggregates after tillage was the highest for the mouldboard plough and the lowest for the moist soil. The energy use for soil fragmentation was in most cases the lowest for the disc harrow, while there were small differences between the chisel and the mouldboard ploughs. The results show that the mouldboard plough is energy efficient for loosening soil, while the disc harrow is energy efficient for soil fragmentation during primary tillage. Tillage at an intermediate water content, close to the plastic limit, gave the largest proportion of small aggregates and consequently the lowest energy use for soil fragmentation. [Copyright &y& Elsevier]

Due to its persistence, subsoil compaction should be avoided, which can be done by setting stress limits depending on the strength of the soil. Such limits must take into account soil moisture status at the time of traffic. The objective of the work presented here was to measure soil water changes during the growing period, use the data to calibrate a soil water model and simulate the soil susceptibility to compaction using meteorological data for a 25-year period. Measurements of soil water content were made in sugarbeet (Beta vulgaris L.) from sowing until harvest in 1997 on two sites classified as Eutric Cambisols in southern Sweden. Sampling was carried out at 2-week intervals in 0.1 m layers down to 1 m depth, together with measurements of root growth and crop development. Precompression stress of the soil at 0.3, 0.5 and 0.7 m depth was determined from uniaxial compression tests at water tensions of 6, 30, 60 and 150 kPa and adjusted as a logarithmic function of the soil water tension. Soil water content was simulated by the SOIL model for the years 1963–1988. Risk calculations were made for a wheel load of 8 t and a ground pressure of 220 kPa, corresponding to a fully loaded six-row sugarbeet harvester. Subsoil compaction was expected to occur when the major principal stress was higher than the precompression stress. The subsoil water content was very low in late summer, but increased during the autumn. At the end of August, there was practically no plant available water down to 1 m depth. There was in general good agreement between measured and simulated values of soil water content for the subsoil, but not for the topsoil. In the 25-year simulations, the compaction risk at 50 cm depth was estimated to increase from around 25% to nearly 100% between September and late November, which is the period when the sugarbeet are harvested. The types of simulation presented here may be a very useful tool for practical agriculture as well as for society, in giving recommendations as to how subsoil compaction should be avoided. [Copyright &y& Elsevier]

Abstract: Autumn tillage strategies designed to reduce leaching losses of nitrogen (N) from arable fields were examined on a medium clay soil (approx. 40% clay) in terms of their effects on accumulation of soil mineral N (SMN) during autumn and winter, crop N uptake, grain yield (spring-sown cereals) and soil structure over the long term (1997–2004). Tillage strategies included mouldboard ploughing (20–25cm depth) and stubble cultivation (10–12cm depth) in different combinations and timing, together with different options for straw management and catch crops. Postponing mouldboard ploughing from early September to early November significantly decreased SMN content during autumn and winter, although levels were generally low in all treatments. On average, the soil profile down to 90cm depth contained 30kgNha−1 in November and 27kgNha−1 in December with early mouldboard ploughing, while the corresponding figures for late mouldboard ploughing were 16 and 21kgNha−1. Stubble cultivation stimulated N mineralisation but the increase in SMN from tillage in September to November was only 3kgha−1 after stubble cultivation, compared with 8kgha−1 after mouldboard ploughing. Stubble cultivation before late mouldboard ploughing resulted in 6kgha−1 higher SMN during autumn than late ploughing without preceding cultivation. Postponement of mouldboard ploughing significantly decreased grain yield by on average 11% and this negative effect accumulated over time. A catch crop compared with no catch crop reduced SMN during autumn and winter by 3–5kgha−1 and had no significant yield effect. Effects of straw incorporation were small and could not be significantly proven either for SMN or yield. Transport of SMN to deeper layers was generally limited and SMN did not decrease during winter, indicating a minor impact of tillage time on N leaching risk. No significant changes in soil physical parameters were detected, but the results indicated poorer soil structure after tillage in late autumn compared with early autumn in terms of higher soil bulk density, lower aggregate stability in water, and lower infiltration rate. Overall, considering the short-term and long-term negative effects on yield and possibly soil structure, the benefit of delaying tillage seems small on this clay soil. [Copyright &y& Elsevier]

Abstract: Soil disturbance by tillage and traffic often adversely affects aggregate stability, leading to colloid and particle mobilisation, which may result in crusting, low water infiltration rate and sediment transport. Hence, minimising soil tillage is an important step in conserving soil quality. This study investigated readily dispersible clay (RDC) and particle transport as affected by shallow tillage or mouldboard ploughing in five Swedish long-term reduced tillage experiments that had been underway for 15–31 years at the time of soil sampling. The soils of the experimental sites are Eutric and Dystric Cambisols. RDC of soil samples, collected in 0–10cm and 12–17cm depth, from mouldboard ploughed (MP) and shallow tillage (ST) plots was compared by measuring turbidity. Particle transport was also determined in undisturbed soil columns (20cm in diameter and 20cm high) from these treatments. RDC and particle transport were significantly lower for ST than for MP at three sites where clay content was above 30%. Particle transport in two soils (clay content above 40%) increased with irrigation events, indicating that preferential transport dominated in unsaturated soil columns, but matrix flow and, consequently, particle dispersion increased as the soil approached saturation. Despite more organic C accumulation in the upper 0–10cm of ST than in the 12–17cm soil layer, clay dispersion was lower in the latter. Particulate P (Total P−dissolved P) was well-correlated to turbidity, suggesting that analysis costs often can be cut by only measuring turbidity. Shallow tillage generally produced positive environmental effects without negative effects on crop yield, especially on soils with high clay content. [Copyright &y& Elsevier]

Abstract: Soil compaction is one of the most important factors responsible for soil physical degradation. Soil compaction models are important tools for controlling traffic-induced soil compaction in agriculture. A two-dimensional model for calculation of soil stresses and soil compaction due to agricultural field traffic is presented. It is written as a spreadsheet that is easy to use and therefore intended for use not only by experts in soil mechanics, but also by e.g. agricultural advisers. The model allows for a realistic prediction of the contact area and the stress distribution in the contact area from readily available tyre parameters. It is possible to simulate the passage of several machines, including e.g. tractors with dual wheels and trailers with tandem wheels. The model is based on analytical equations for stress propagation in soil. The load is applied incrementally, thus keeping the strains small for each increment. Several stress–strain relationships describing the compressive behaviour of agricultural soils are incorporated. Mechanical properties of soil can be estimated by means of pedo-transfer functions. The model includes two options for calculation of vertical displacement and rut depth, either from volumetric strains only or from both volumetric and shear strains. We show in examples that the model provides satisfactory predictions of stress propagation and changes in bulk density. However, computation results of soil deformation strongly depend on soil mechanical properties that are labour-intensive to measure and difficult to estimate and thus not readily available. Therefore, prediction of deformation might not be easily handled in practice. The model presented is called SoilFlex, because it is a soil compaction model that is flexible in terms of the model inputs, the constitutive equations describing the stress–strain relationships and the model outputs. [Copyright &y& Elsevier]