Search

The concept of self-healing concrete is becoming more necessary as sustainability in construction is more desirable. Amongst the current solutions in this technology are autogenous, chemical, and bacterial self-healing. It is paramount that secondary raw materials be used in the production of selfhealing concrete as a form of a sustainable solution. Therefore, in this paper, the admixture “Betocrete-CP-360-WP”, which is a crystallizing waterproofing admixture with hydrophobic effect and is 100% recyclable, has been used and its effect on the physical, chemical, and mechanical properties of concrete, as well as selfhealing capabilities of concrete, have been determined. According to the obtained results, the crystalline additive “Betocrete-CP-360-WP” has no effect on density and slightly increases the amount of entrained air in the concrete mix. However, it does decrease the workability of the concrete mixture which could prove problematic in transportation to the construction site or in concreting in general. Also, with the crystalline admixture in the concrete mix, a 60% reduction in concrete compressive strength after one day of hardening has been estimated, but after 7 and 28 days, the strength attained is within the ranges of the control samples. In addition, concrete containing Betocrete-CP360-WP was 30% less water permeable as compared to control samples. The self-healing efficiency of the concrete was determined by a water flow test through a formed crack (approximately 0.35 mm wide). This was done by gluing a plastic pipe to the top of the cracked concrete specimens and maintaining a constant pressure of the water in the pipe. The experiment was continued for 28 days, and the crack self-healing efficiency of the concrete was calculated from the differences in the amount of water passed through the crack before healing and after 7, 14, 21 and 28 days of the healing process. After 28 days of the water flow test, the cracks in the concrete with the crystalline admixture and recycled concrete dust were completely healed, while the control specimens were not.

The article focuses on investigation of mechanical and fracture properties of concrete containing electrical cable waste as well as some microstructural features of such concrete. Added to concrete, electrical cable waste reduces the overall concrete bulk density. Compressive, flexural, tensile splitting strengths and elastic modulus decreased when electrical cable waste was admixed to conventional and polymer modified concretes. The best mechanical properties of concrete samples containing electrical cable waste were identified in polymer modified concrete containing 5% of electrical cable waste. Electrical cable waste particles increase the deformability of polymer modified concretes and have almost no influence on normal concrete. Consequently, the optimal amount of electrical cable waste particles can provide concrete with desirable strength that is required for different applications. [ABSTRACT FROM AUTHOR]

In the construction industry, the selection of sustainable materials leads to a movement towards more sustainable construction. In this study, lightweight aggregate shotcrete based on expanded glass (EG) and expanded clay (EC) is investigated. The goal of the study is to determine the influence of EG and EC inclusion on the properties of shotcrete. Ordinary Portland cement (OPC) powder with supplementary cementitious materials, such as silica fume and ground glass waste, are used as binders. The mechanical, physical and morphological properties, as well as the mineral and oxygen compositions, are obtained through compressive and flexural strength tests, thermal conductivity measurements, scanning electron microscopy with energy dispersive X-ray spectrometry (SEM–EDX), X-ray diffraction (XRD) and X-ray fluorescence (XRF) analysis. In this study, the mechanical, physical and thermal properties and waste utilization as cement supplementary materials are balanced. The shotcrete samples show that a density of 790 kg/m3 had a good thermal performance (thermal conductivity coefficient of 0.174 W/(m·K)) with the sufficient compressive strength of 6.26 MPa. [ABSTRACT FROM AUTHOR]

This paper analyzes concrete fine aggregate (sand) modification by scrap tire rubber particles-fine crumb rubber (FCR) and coarse crumb rubber (CCR) of fraction 0/1 mm. Such rubberized concrete to get better bonding properties were modified by car-boxylated styrene butadiene rubber (SBR) latex and to gain the strength were modified by glass waste. The following tests—slump test, fresh concrete density, fresh concrete air content, compressive strength, flexural strength, fracture energy, freezing-thawing, porosity parameter, and scanning electron microscope—were conducted for rubberized concretes. From experiments, we can see that fresh concrete properties decreased when crumb rubber content has increased. Mostly it is related to crumb rubber (CR) lower specific gravity nature and higher fineness compared with changed fine aggregate-sand. In this research, we obtained a slight loss of compressive strength when CR was used in concrete However, these rubberized concretes with a small amount of rubber provided sufficient compressive strength results (greater than 50 MPa). Due to the pozzolanic reaction, we see that compressive strength results after 56 days in glass powder modified samples increased by 11–13% than 28 days com-pressive strengths, while at the same period control samples increased its compressive strength about 2.5%. Experiments have shown that the flexural strength of rubberized concrete with small amounts of CR increased by 3.4–15.8% compared to control mix, due the fact that rubber is an elastic material and it will absorb high energy and perform positive bending toughness. The test results indicated that CR can intercept the tensile stress in concrete and make the deformation more plastic. Fracturing of such conglomerate concrete is not brittle, there is no abrupt post-peak load drop and gradually continues after the maximum load is exceeded. Such concrete requires much higher fracture energy. It was obtained that FCR particles (lower than A300) will entrap more micropores content than coarse rubbers because due to their high specific area. Freezing-thawing results have confirmed that Kf values can be conveniently used to predict freeze-thaw resistance and durability of concrete. The test has shown that modification of concrete with 10 kg fine rubber waste will lead to similar mechanical and durability properties of concrete as was obtained in control concrete with 2 kg of prefabricated air bubbles. [ABSTRACT FROM AUTHOR]

Self-healing concrete has the potential to optimise traditional design approaches; however, commercial uptake requires the ability to harmonize against standardized frameworks. Within EU SARCOS COST Action, different interlaboratory tests were executed on different self-healing techniques. This paper reports on the evaluation of the effectiveness of proposed experimental methodologies suited for self-healing concrete with expansive mineral additions. Concrete prisms and discs with MgO-based healing agents were produced and precracked. Water absorption and water flow tests were executed over a healing period spanning 6 months to assess the sealing efficiency, and the crack width reduction with time was monitored. High variability was reported for both reference (REF) and healing-addition (ADD) series affecting the reproducibility of cracking. However, within each lab, the crack width creation was repeatable. ADD reported larger crack widths. The latter influenced the observed healing making direct comparisons across labs prone to errors. Water absorption tests highlighted were susceptible to application errors. Concurrently, the potential of water flow tests as a facile method for assessment of healing performance was shown across all labs. Overall, the importance of repeatability and reproducibility of testing methods is highlighted in providing a sound basis for incorporation of self-healing concepts in practical applications. [ABSTRACT FROM AUTHOR]