Search

Due to the high cost and the predicted shortage of rare earth elements in the near future, the task of developing energy-efficient electric machines without rare earth magnets is of great importance. This article presents a comparative analysis of optimized designs of a ferrite-assisted synchronous reluctance machine (FaSynRM) and a ferrite-assisted synchronous homopolar machine (FaSHM) in a 370-kW subway train drive. The objectives of optimizing these traction machines are to reduce their losses, maximum armature current, and torque ripple. The optimization considers the characteristics of the machines in the subway train moving cycle. The problem of the risk of irreversible demagnetization of ferrites in the FaSynRM and FaSHM is also considered. To reduce the computational burden, the Nelder-Mead method is used for the optimization. It is shown that the FaSHM demonstrates better field weakening capability, which can reduce the maximum current, power, and cost of the inverter power modules. At the same time, the FaSynRM requires less permanent magnet mass for the same torque density and is more resistant to irreversible demagnetization, which can reduce costs and improve the reliability of the electric machine. [ABSTRACT FROM AUTHOR]

Featured Application: The findings of this study can be applied in the design and experimental investigation of line-start permanent magnet motors. Line-start permanent magnet synchronous motors (LSPMSMs) are of great interest to researchers because of their high energy efficiency, due to the growing interest of manufacturers in energy-efficient units. However, LSPMSMs face some difficulties in starting and synchronization processes. The LSPMSM lumped parameter model is applicable to estimating the successfulness of starting and further synchronization. The parameters of such a model can be determined using computer-aided identification algorithms applied to real motor transient processes' curves. This problem demands significant computational time. A comparison between two algorithms, differential evolution and Nelder–Mead, is presented in this article. The algorithms were used for 0.55 kW, 1500 rpm LSPMSM parameter identification. Moreover, to increase computational speed, it is proposed to stop and restart the algorithms' procedures, changing their parameters after a certain number of iterations. A significant advantage of the Nelder–Mead algorithm is shown for the solving of the considered problem. [ABSTRACT FROM AUTHOR]

Featured Application: The research findings can be applied in the design of generators of various vehicles, in particular synchronous homopolar generators. Electric machines with hybrid excitation have increased torque density while maintaining a wide range of speed control. This article presents the results of the optimal design of a synchronous homopolar generator (SHG) with ferrite magnets on the rotor and excitation winding on the stator for passenger cars. The use of ferrite magnets on the rotor of a synchronous homopolar generator makes it possible to use the stator surface more efficiently, which in turn increases energy efficiency and reduces the dimensions of the generator. At the same time, the excitation winding on the stator provides a reliable brushless design and the ability to control the excitation flux. The problem of long-time calculation of the three-dimensional SHG structure, which is especially relevant when using multi-iterative computer optimization, is solved by using the computationally efficient Nelder-Mead method and a simplified SHG model using two-dimensional finite element analysis. It is also clear that the low torque ripple of SHG with ferrite magnets with two stator-rotor stack combinations (SRSC) is largely provided by the fact that the torque ripples of individual SRSCs are in antiphase. The problem of considering the magnetic properties of magnetic core sections made of structural low-carbon steel is discussed. It has been found that with an increase in both the saturation level of the magnetic circuit and the magnetomotive force (MMF) of the SHG excitation winding, resistance to irreversible demagnetization of ferrite magnets on the rotor can be increased by increasing their height. In addition, it is shown that there is a significant increase in performance when using the hybrid excitation, in comparison with the conventional SHG design without magnets. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used in designing synchronous homopolar machines and railway undercar generators. The article presents the optimal design of a 35 kW brushless synchronous homopolar generator without permanent magnets for railway passenger cars. The excitation winding of the generator is located on the stator, and the toothed rotor has no windings. The generator characteristics are optimized considering the required constant power speed range. A single-objective Nelder–Mead algorithm and 2D Finite Element Analysis were used for the optimization. As a result of the optimization, power losses are significantly reduced over the entire operating range of the generator rotational speed, the current capacity of the solid-state rectifier, and the torque ripple. A comparison of the calculated characteristics of the generator under consideration with the characteristics of a commercially available undercar generator shows that the active volume is reduced by a factor of 2.1, and the losses are significantly reduced over the entire operating speed range. [ABSTRACT FROM AUTHOR]

Brushless synchronous homopolar machines (SHM) have long been used as highly reliable motors and generators with an excitation winding on the stator. However, a significant disadvantage that limits their use in traction applications is the reduced specific torque due to the incomplete use of the rotor surface. One possible way to improve the torque density of SHMs is to add inexpensive ferrite magnets in the rotor slots. This paper presents the results of optimizing the performances of an SHM with ferrite magnets for a subway train, considering the timing diagram of train movement. A comparison of its characteristics with an SHM without permanent magnets is also presented. When using the SHM with ferrite magnets, a significant reduction in the dimensions and weight of the motor, as well as power loss, is shown. [ABSTRACT FROM AUTHOR]

The use of Line-Start Permanent Magnet Synchronous Motors (LSPMSM) improves the efficiency of conventional direct-on-line electric motor-driven fluid machinery such as pumps and fans. Such motors have increased efficiency compared to induction motors and do not have an excitation winding compared to classical synchronous motors with an excitation winding. However, LSPMSMs have difficulty in starting mechanisms with a high moment of inertia. This problem can be exacerbated by a reduced supply network voltage and a voltage drop on the cable. This article investigates the transients during the startup of an industrial centrifugal pump with a line-start permanent magnet synchronous motor. The simulation results showed that when the voltage on the motor terminals is reduced by 10%, the synchronization is delayed. The use of the cable also leads to a reduction in the voltage at the motor terminals in a steady state, but the time synchronization delay is more significant than that with a corresponding reduction in the supply voltage. The considered simulation example shows that the line-start permanent magnet synchronous motor has no problems with starting the pumping unit, even with a reduced supply voltage. The conclusions of this paper support a wider use of energy-efficient electric motors and can be used when selecting an electric motor to drive a centrifugal pump. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used in designing of synchronous homopolar machines and traction electrical drives. Synchronous homopolar motors have no permanent magnets and their excitation winding is fixed at their stator. However, they can be a good alternative to induction and permanent magnet motors in traction applications requiring a wide constant power speed range. They provide an excitation flux control and a highly reliable brushless rotor design. This article presents the procedure and results of optimizing a 370 kW synchronous homopolar motor for driving subway train. The optimization procedure was developed to take into account the subway train moving trajectory. The analysis considers only a limited number of steady-state operating points of the motor to reduce computation time. The optimization results show a significant improvement of the target parameters of the traction drive. The optimization makes it possible to significantly reduce the losses in the operating cycle, as well as the torque ripple of the motor and the current rating of the traction inverter. [ABSTRACT FROM AUTHOR]

Direct-on-line synchronous motors are a good alternative to induction motors in fluid machinery drives due to their greater energy efficiency but have the significant disadvantage of limiting the maximum moment of inertia of the loading mechanism to ensure their successful and reliable start-up. This disadvantage is critical in centrifugal fans with a massive steel impeller. In this article, using a mathematical model, the dynamics of starting and synchronizing a permanent magnet synchronous motor fed directly from the mains as part of a fan drive are studied. The simulation results show the possibility of increasing the maximum moment of inertia of the load at the successful start-up of a direct-on-line synchronous motor by adjusting the hydraulic part of the fan pipeline by means of throttling. The conclusions of this paper can be used when selecting an electric motor to drive industrial fans and can contribute to wider use of energy-efficient synchronous motors with direct start-up from the mains. [ABSTRACT FROM AUTHOR]

A synchronous homopolar motor (SHM) has a salient pole passive rotor, an excitation winding located on the stator, and no permanent magnets, which ensures high reliability and makes this type of motor a good alternative to motors traditionally used in traction drives. However, there is no comparison between SHMs and conventional brushed synchronous machines for traction applications in the literature. In this paper, the performances of a wound rotor synchronous machine (WRSM) and SHM are theoretically compared at the operating points of a 370 kW dump mining truck drive traction curve that has a 10:1 constant power range in the field weakening region. The nine-phase motors under comparison have the same outer diameter of the stator lamination. Before comparison, both motor designs are optimized using the Nelder–Mead method to minimize the semiconductor inverter rated current and the operating cycle power loss. The main advantages of the WRSM, which was designed, are reduction in stator length, smaller losses, and smaller inverter. The reduction in the total stator length was by 1.23 times taking into account the winding end parts as well. Losses were reduced by 1.21 times for the same radius of the stator lamination. Finally, the cost of power modules of the inverter was decreased by 1.4 times. SHM is more reliable since its rotor does not have an excitation winding and a diode rectifier, as in a WRSM with a brushless exciter. In addition, SHM provides lower consumption of copper, which reduces the total mass and cost of active materials. This article also introduces a new term, "inverter utilization factor", which can be useful, more informative than motor power factor, when comparing traction drives with different types of motors. [ABSTRACT FROM AUTHOR]

Synchronous homopolar motors (SHMs) with an excitation winding located at the stator and a toothed salient pole rotor are a good alternative to motors traditionally used in traction applications such as induction motors or interior permanent magnet synchronous motors (IPMSM). This study presents the results of a theoretical comparison between an IPMSM and an SHM in a traction application with a constant power speed range of 1:10, which is specific to the mining truck drives, and with a rated power of 370 kW. The considered IPMSM and SHM have the same number of phases, poles and stator slots, and the same outer diameter of the stator lamination. The IPMSM design is optimized using the Nelder–Mead method. The main objectives of optimization are to minimize the average losses in the operating cycle and to limit the required power of the semiconductor inverter. The performance of the optimized IPMSM is compared with the previously obtained performance of the SHM optimized by the same method. Although the average losses in the operating cycle in the compared motors are approximately equal, the losses at high speed for the IPMSM are about two times greater than at low speed with maximum torque, which means that there is a need to intensify the IPMSM cooling system and there is deterioration of reliability. The advantage of the IPMSM is the reduction in the length of the active part by 30%. The advantage of the SHM is that there is 4.6 times lower cost of active materials. In addition, the SHM is more reliable than the IPMSM, as there is no risk of overheating, demagnetization or degradation of permanent magnets over time. [ABSTRACT FROM AUTHOR]

Despite the great potential and the high performance of energy-efficient line-start permanent magnet synchronous motors (LSPMSMs), their developers face a great deal of difficulties, one of which is the lack of reliable and accurate testing methods for such electrical machines. In this paper, we propose a new method for indirectly determining the efficiency of LSPMSM through the summation of individual loss components. The standard input-output method usually used for these machines is based on torque measurement, requires expensive measuring equipment, and, as a rule, has great uncertainty. Contrarily, the proposed method does not require direct measurement of torque and mechanical power on the shaft and is less sensitive to measurement uncertainties. The theoretical substantiation of the proposed method and its experimental verification using a commercially available four-pole LSPMSM with a rated power of 0.55 kW are presented. Satisfactory convergence of the experimental results obtained using the standard input-output method and using the proposed indirect method is shown. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used to assess the energy-saving potential of various topologies of multi-pump pumping stations. The energy efficiency of a multi-pump system consisting of two low-power (0.75 kW) pumps operating in parallel mode and a single-pump mechanism (1.5 kW) is compared in this study. For this purpose, mathematical models, experimental data, and data retrieved from the manuals provided by the pump manufacturers are used. The single-pump system is fed by a single variable speed drive. A multi-pump system running in parallel mode consists of two pumps. One of them is driven by an induction motor connected directly to the electrical grid and equipped with a throttle. Another pump is actuated by an induction motor fed by a variable speed drive. The flowrate of the liquid in the multi-pump is controlled with the help of speed variation and throttling. In the case of the single-pump system the conventional speed control method is applied during the analysis. For both pump system topologies, the daily and annual energy consumption is obtained. As a result of conducted calculations, it was shown that the multi-pump provides 29.8% savings in comparison to the single-pump system in the case of a typical flowrate profile. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used to evaluate the energy-saving potential and ecological impact of electric motors of various energy efficiency classes in various applications of electric drive. The high energy intensity of the modern industry and the threat of climate change determine the high urgency of increasing the energy efficiency of electric motors. In this paper, energy consumption, energy costs, payback periods, and CO2 emissions of 75 kW, 4 pole induction motors with direct grid supply in a fixed-speed pump unit are evaluated. Motors of the IE2, IE3, and IE4 efficiency classes according to IEC 60034-30-1 standard are compared in terms of life-time energy savings, payback period, and CO2 emissions. To carry out the analysis, polynomial interpolation of the data from the available manufacturer datasheets of the motors is used. It concluded that even though the initial investment cost of the IE4-motor is higher than that of IE3-motor, the IE4-motor is more profitable if more than 3 years of operation are considered and also provides significant reductions of CO2 emissions. The paper presents a calculation method of the aforementioned indicators which can be useful for companies, researchers, and engineers for quick assessment and selection of technical solutions. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used to assess the energy-saving potential of general-purpose and industrial electric motors of various types in various applications of electric drives. The high energy intensity of the modern industry determines the high urgency of increasing the energy efficiency of production processes. However, a big number of motor types of enhanced efficiency classes are available on the market. The motor users can be confused about the choice of the right motor solution for a certain application. In this paper, to help with this choice the energy efficiency indicators of various types of electric motors in a low-power pump unit with a constant rotation speed are studied. Moreover, not only power losses in the motor are considered, but also power losses in the cable and transformer, which are influenced by the power factor of the motor. Induction motors (IMs) and synchronous motors powered directly from the grid (direct-on-line synchronous motor with permanent magnet in the rotor, DOL PMSM; direct-on-line synchronous reluctance motor without permanent magnet, DOL SynRM) of IE2, IE3, and IE4 energy efficiency classes are compared. To carry out the analysis, polynomial interpolation of the available catalogue data and experimental data of the motors are used. The main criteria for comparing different motors in this work are the energy savings over the pump's life cycle and the payback period when replacing an IE2 motor with a motor of a higher energy efficiency class. The article shows that although the DOL PMSM has a lower motor efficiency than the DOL SynRM, it saves more energy due to its higher power factor, which reduces cable and transformer losses. It is also shown that, despite the highest initial cost, when taking into account cable and transformer losses, the payback period of DOL PMSM can be shorter than that of IE3 and IE4 induction motors. DOL SynRM has the shortest payback period in all considered cases, has no troublesome rare-earth permanent magnets, and can also be a valuable solution. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used in designing of single-phase high-speed electrical drives. Single-phase motors are used in low-power, cost-effective, variable-speed applications. As a replacement to traditional single-phase synchronous motors with magnets on the rotor, single-phase flux reversal motors (FRMs) with a rugged and reliable toothed rotor are considered for the high-speed applications. However, torque pulsations of single-phase motors are high. The aim of this work is to minimize the torque ripple and increase its minimum instantaneous value, as well as to reduce FRM losses. To solve this problem, an asymmetric rotor is used, and an objective function is proposed, which includes parameters characterizing the pulsations of the torque and the loss of FRM for two load conditions. To optimize the single-phase FRM and minimize the objective function, the Nelder–Mead method was applied. The optimization criterion was selected to maximize the efficiency, to reduce the torque ripple, and to the avoid the negative torque in a wide range of powers at the fan load (quadric dependence of torque on speed). Two operating loading modes are considered. After two stages of optimization, the peak-to-peak torque ripple in the FRM in the rated loading mode decreased by 1.7 times, and in the mode with reduced load by 2.7 times. In addition, in the FRM before optimization, the torque has sections with negative values, and in the FRM after optimization, the torque is positive over the entire period. Although losses in the rated mode increased by 4%, when underloaded, they decreased by 11%, which creates an additional advantage for applications that work most of the time with underload. [ABSTRACT FROM AUTHOR]

Featured Application: The presented results can be used to assess the energy-saving potential of general purpose and industrial electric motors of various types in various applications of electric drives. The paper presents a comparative analysis of energy consumption by 2.2 kW electric motors of various types and energy efficiency classes in the electric drive of a pump unit with throttle control in a water supply system. Line-start permanent-magnet synchronous motors of the IE4 energy efficiency class and induction motors of the IE4 and IE3 energy efficiency classes of various manufacturers were considered (IE4 and IE3 are labels of energy efficiency classes of electric motors according to IEC 60034-30-1 standard). Energy consumption at a hydraulic load changing under a typical duty cycle was calculated based on the nameplate data of the pump and electric motors. The developed method shows that selecting an electric motor based on the IE energy efficiency class under the IEC 60034-30-1 standard (i.e., based on efficiency at a rated load) may not provide the minimum energy consumption of a variable flow pump unit over a typical duty cycle. In particular, the considered IE4 class line-start permanent-magnet synchronous motors do not provide significant advantages over IE4 class induction motors, and sometimes even over IE3 class induction motors when they are used in variable flow pump units. [ABSTRACT FROM AUTHOR]

A single-phase flux reversal machine (FRM) has many advantages in high-speed applications because of its simple and reliable rotor structure without magnets or winding, simple and cheap concentrated stator windings, high efficiency, and power density. However, the major problem of single-phase motors is the high torque ripple, which shortens their lifetime and causes noise and vibrations, not only in the machine, but also in the mechanisms coupled therewith. This paper presents a novel three-phase machine consisting of three single-phase machines, having a common shaft aiming to reduce the torque ripple and to improve motor behavior. In this paper, the mathematical model of the single-phase flux reversal motor, as well as the conversion procedure of the single-phase motor parameters to the three-phase ones, is considered. Furthermore, an optimization procedure of the motor and choosing the optimization objectives are done. The finite element two-dimensional (2D) method is used to simulate the machine and to show the results. [ABSTRACT FROM AUTHOR]

This paper considers an optimization of the IE5 four-pole synchronous reluctance motor of a new design. The motor has an original rotor design and a stator with a fractional-slot winding (2.5 slots per pole and phase). The target parameters of optimization are the resulting efficiency of the motor at the fan load profile, the torque ripple, the required power of the frequency converter, and the total harmonic distortion of the supply voltage. The motor efficiency is much higher than the IE5 class requirement and remains high in wide range of powers at the fan load profile. Also, the motor has low torque ripple despite that its rotor and stator have no skewing. [ABSTRACT FROM AUTHOR]

The article describes a mathematical model of interconnected electromechanical and thermal processes in a linear induction motor (LIM). Here, we present the structure of the thermal model and provide the calculation formulas of the model. The thermal model consisted of eight control volumes on each tooth pitch of the LIM. Moreover, we also present a model of electromechanical processes and its interaction with the thermal model. The electromechanical model was based on the detailed magnetic and electrical equivalent circuits of the LIM. Model verification was performed using a model based on the finite element method and using experimental data. We also conducted a study focused on the necessity of considering the influence of various features of the thermal processes. We herein discuss the application of the model implemented in the MATLAB/Simulink, which was used to analyze the thermal performance of linear transport and technological induction motors. For the traction single-sided linear induction motor, we determined limits of safe operation by considering the unevenness of heating along the length in two cases: natural cooling and forced cooling. For forced cooling, required values of air flow were determined. For the arc induction motor of the screw press, the influence of various factors (i.e., reduction of the stroke, the use of a soft start, and the use of a forced cooling) on heating was evaluated. [ABSTRACT FROM AUTHOR]

The synchronous homopolar motor (SHM) with an excitation winding on the stator and a toothed rotor is a good alternative to traction induction motors for hybrid mining trucks. The main problem in the design of the SHM electric drives is that the magnetic flux forms three-dimensional loops and, as a result, the lack of high-quality optimization methods, which leads to the need to overrate the installed power of the inverter. This article discusses the procedure and results of optimization of a commercially available 370 kW traction SHM using the Nelder–Mead method. The objective function is composed to mainly improve the following characteristics of the traction SHM: total motor power loss and maximum armature winding current. In addition, terms are introduced into the objective function to make it possible to limit the voltage, the loss in the excitation winding, and the maximum magnetic flux density in the non-laminated sections of the magnetic core. As a result of the optimization, the motor losses and the maximum current required by the motor from the inverter were significantly reduced. The achieved reduction in the maximum current allows the cost of the IGBT modules of the inverter to be reduced by 1.4 times (by $ 2295), and also allows the AC component of the DC-link current to be reduced by the same amount. [ABSTRACT FROM AUTHOR]

This study carried out a comparative analysis of indicators of electricity consumption and CO2 emissions for four-pole induction motors (IMs) of efficiency classes IE3 and IE4 with a rated power of 2.2–200 kW in a variable speed pump unit. In addition, innovative IE4 converter-fed synchronous reluctance motors (SynRMs) were evaluated. The comparison was derived from the manufacturer's specifications for the power drive systems (PDSs) at various rotational speeds and loads. The results showed that the emission indicators for IE3 class motors were significantly worse compared with IE4 class motors for low power ratings, which make up the vast majority of electric motors in service. This justifies expanding the mandatory power range for IE4 motors to at least 7.5–200 kW or even 0.75–200 kW, as it will dramatically contribute to the achievement of the new ambitious goals for reducing greenhouse gas emissions. In addition, the operational advantages of IE4 SynRMs over IE4 IMs were demonstrated, such as their simpler design and manufacturing technology at a price comparable to that of IE3 IMs. [ABSTRACT FROM AUTHOR]

The paper compares the economic effect of using capacitors in fixed speed drives of a pumping station when using energy-efficient motors of various types. Induction motors of IE2 and IE3 energy efficiency classes, a direct-on-line synchronous motor with a permanent magnet in the rotor, and a direct-on-line synchronous reluctance motor are considered. The comparison takes into account not only the efficiency of the motors, but also their power factor, on which the losses in the cable and transformer depend. The possibility of using static capacitors to compensate for the reactive power of motors and reduce the losses is also considered. The feasibility analysis takes into account that the motors have different initial costs. The cost of capacitors is also taken into consideration. The analysis shows that the use of static capacitors can have a significant impact on the comparison between different motors in this application. Without considering capacitors, the permanent magnet motor has the shortest payback period, otherwise the synchronous reluctance motor has the shortest payback period. [ABSTRACT FROM AUTHOR]

The paper discusses the use of the combined control for a system of two parallel pumps to increase its service life. Using the combined control, the pumping system is controlled together by change the speed, throttling, and bypass. The power consumption of the pumping system is calculated for three methods of flow control: with minimum energy consumption, with maximum reliability, and control with a trade-off between efficiency and reliability. In the case of control with maximum reliability, the energy consumption of the pumping system is higher than in the case of control with minimum energy consumption by 29.2%. In the case of the proposed trade-off control, which provides acceptable reliability, the power consumption is higher than with the minimum energy consumption control by only 7.3%. [ABSTRACT FROM AUTHOR]

Synchronous homopolar motors (SHMs) have been attracting the attention of researchers for many decades. They are used in a variety of equipment such as aircraft and train generators, welding inverters, and as traction motors. Various mathematical models of SHMs have been proposed to deal with their complicated magnetic circuit. However, mathematical techniques for optimizing SHMs have not yet been proposed. This paper discusses various aspects of the optimal design of traction SHMs, applying the one-criterion unconstrained Nelder–Mead method. The considered motor is intended for use in a mining dump truck with a carrying capacity of 90 tons. The objective function for the SHM optimization was designed to reduce/improve the following main characteristics: total motor power loss, maximum winding current, and torque ripple. One of the difficulties in optimizing SHMs is the three-dimensional structure of their magnetic core, which usually requires the use of a three-dimensional finite element model. However, in this study, an original two-dimensional finite element model of a SHM was used; it allowed the drastic reduction in the computational burden, enabling objective optimization. As a result of optimization, the total losses in the motor decreased by up to 1.16 times and the torque ripple decreased by up to 1.34 times; the maximum armature winding current in the motor mode decreased by 8%. [ABSTRACT FROM AUTHOR]

Reliability, along with energy efficiency, is an important characteristic of pump units in various applications. In practical pump applications, it is important to strike a balance between reliability and energy efficiency. These indicators strongly depend on the applied control method of the pump unit. This study analyzes a trade-off method for regulating a system with three parallel pumps equipped with only one frequency converter (multi-pump single-drive system). A typical operating cycle of a pumping system with variable flow rate requirements is considered. The proposed trade-off method is compared with the traditional regulation, when a change in the operating point of the pump is achieved only by changing the rotation speed, and with the method for maximum reliability. It is shown that the proposed trade-off method makes it possible to ensure sufficient reliability of the multi-pump system operation without a significant increase in energy consumption. [ABSTRACT FROM AUTHOR]

The permanent magnet flux-switching machine (PMFSM) is one of the most promising machines with magnets inserted into the stator. To determine in which applications the use of PMFSM is promising, it is essential to compare the PMFSM with machines of other types. This study provides a theoretical comparison of the PMFSM with a conventional interior permanent magnet synchronous machine (IPMSM) in the gearless generator of a low-power wind turbine (332 rpm, 51.4 Nm). To provide a fair comparison, both machines are optimized using the Nelder–Mead algorithm. The minimized optimization objectives are the required power of frequency converter, cost of active materials, torque ripple and losses of a generator averaged over the working profile of the wind turbine. In order to reduce the computational time, the substituting profile method is applied. Based on the results of the calculations, the advantages and disadvantages of the considered machines were revealed: the IPMSM has significantly lower losses and higher efficiency than the PMFSM, and the PMFSM requires much less rare-earth magnets and copper and is, therefore, cheaper in mass production. [ABSTRACT FROM AUTHOR]

Single-phase flux reversal motors (FRMs) with sintered rare-earth permanent magnets on the stator for low-cost high-speed applications have a reliable rotor and a good specific power. However, to reduce eddy current loss, the sintered rare-earth magnets on the stator have to be segmented into several pieces and their cost increases with the number of magnet segments. An alternative to the sintered magnets can be bonded magnets, in which eddy current loss is almost absent. The remanence of bonded magnets is lower than that of sintered magnets, and they are prone to demagnetization. However, the cost of low-power motors with bonded magnets can be lower because of the simpler manufacturing technology and the lower material cost. This paper discusses various aspects of the optimal design of FRM with bonded magnets, applying the Nelder–Mead method. An objective function for optimizing an FRM with bonded magnets is designed to ensure the required efficiency, reduce torque oscillations, and prevent the bonded magnets from demagnetizing. As a result, it is shown that the FRM with bonded magnets has approximately the same efficiency as the FRM with sintered magnets. In addition, the peak-to-peak torque ripple is minimized and the minimal instantaneous torque is maximized. [ABSTRACT FROM AUTHOR]

The paper presents a comparative analysis of life-cycle energy consumption for three different types of 4 kW line-start motors used in a pump unit with throttling: the most widely used induction motor with IE3 efficiency class, line start permanent magnet synchronous motor with IE4 efficiency class and line start synchronous reluctance motor with IE4 efficiency class. The operating cycle for pump units with constant flow is considered for the above-mentioned types of motors taking into account not only the losses in the pump and motor, but also in the power supply cable. It is shown that the line start synchronous reluctance motor without magnets has the highest efficiency over the entire considered loading range. However, its power factor is lower than that of the synchronous motor with magnets and therefore it has more significant losses in power supply cable. Despite this disadvantage, the line-start reluctance motor is a good alternative to widespread induction motor since it allows saving of approximately 4000 euro more than the latter during the 20 years life cycle. It also provides similar savings in comparison to the permanent magnet synchronous motor, but unlike it, it does not have costly rare-earth materials in the rotor. [ABSTRACT FROM AUTHOR]

In this paper, the optimal design of the Flux-Switching Generator with ferrite magnets based on a two-mode substituting load profile for a gearless wind generator is considered. A one-criterion Nelder-Mead method is used to optimize the generator design. The optimization function is constructed mainly so as to minimize the average losses in the generator and the required AC–DC converter power. Also, the Flux-Switching Generator torque-ripple and the ferrite magnets volume are minimized. Using substituting profiles instead of initial ones reduces the calculation efforts substantially. The paper contains the analysis of the optimal design of the Flux-Switching Generator with ferrite magnets. [ABSTRACT FROM AUTHOR]

Due to the increasing need for direct-drive wind turbines, a large number of papers are dedicated to the optimization of low-speed wind generators. A permanent-magnet flux-switching machine can be a valuable option to use in such applications. This paper describes the optimization procedure of a direct-drive flux-switching wind generator. The average losses, the required converter power, and the cost of permanents magnets were chosen as the optimization objectives. To reduce the calculation efforts during the optimization, a method to construct the substituting load profiles is proposed. Two-mode and three-mode substituting profiles were constructed on the basis of the nine-mode initial profile. The losses calculated under the two-mode, three-mode, and nine-mode profiles accurately coincided, which supported the use of the low-mode substituting profiles instead of the initial one. During the optimization, the average losses decreased by 30%, which corresponded to an increase in the average efficiency by almost 6%. The required converter power was decreased by 10%. The total active material mass, cogging torque, and torque ripple were also slightly decreased. [ABSTRACT FROM AUTHOR]

Due to the rapid increase in the number of variable speed AC drives, the analysis of their energy efficiency has become highly essential. However, such an analysis requires consideration of a wide variety of factors. This includes considering the energy loss in the frequency converter, depending on the motor type. In this article, a computational comparison of the energy properties of variable frequency pump drive employing two types of electric machines, i.e. an induction and a synchronous reluctance motor, is presented. The effect of the motor type on the losses in a low-voltage two-stage frequency converter using analytical and numerical models, with a further comparison, is investigated. Furthermore, an alternative approach to determine the current magnitude and power factor of the load of the converter is suggested. Eventually, this study provides a quantitative estimate of the increase in losses in the converter caused by using the two different motor types. Several experimental tests are conducted on induction and synchronous 1.1 kW reluctance motors. [ABSTRACT FROM AUTHOR]

This paper describes the design of a single-phase high-speed flux reversal motor (FRM) for use in a domestic application (vacuum cleaner). This machine has a simple and reliable rotor structure, which is a significant advantage for high-speed applications. An FRM design in which the inner stator surface is entirely used allows it to decrease its volume and increase its efficiency. The mathematical modeling, based on the finite element method, and the optimal design of the high-speed single-phase FRM are described. The criterion of optimization and the selection of a proper optimization algorithm are discussed. Since the finite element method introduces a small but quasi-random error due to round-off accumulation and choosing the mesh, etc., the Nelder-Mead method, not requiring the derivatives calculation, was chosen for the optimization. The target parameter of the optimization is built for the motor efficiency when operating at different loads. Calculations show that the presented approach provides increasing motor efficiency during the optimization, particularly at underload. [ABSTRACT FROM AUTHOR]