Search

Solar energy is one of the most important sources of renewable energies, which is widely used in many fields, such as electricity production through direct production of superheated steam based on Linear Fresnel Reflector. This study aims to show the optical and thermal behavior of linear Fresnel solar reflectors field directed to the electricity production in El-Oued region at Algeria. Four days of different weather data have been selected to track the change in solar field performance. Numerical optical modeling has shown that the optical performance of the solar field has reached 53.60 %, while the thermal study based on the numerical solution of the energy balance equations of the receiver tube proved that the thermal efficiency was 37.3 % and the average thermal loss coefficient was limited between 5.72 and 5.98 W/m²K. As for the superheated steam temperature, the lowest value was recorded in December with a value of 501 K. The results obtained are very compelling and encouraging to invest in this low-cost technology.

Ensuring the uniformity of solar irradiance distribution on photovoltaic cells is a major challenge in low-concentrating photovoltaic systems based on a small-scale linear Fresnel reflector. A novel sawtooth V-cavity design method based on an optimization algorithm to achieve uniform irradiance distribution on photovoltaic cells is presented. The reliability of the design was verified using the Monte Carlo ray-tracing method and a laser experiment. A prototype was built using 3D printing technology with a biodegradable green polymer material known as polylactic acid. The new cavity was compared to the standard V-trough cavity, keeping the cavity aperture, reflective surface area, and photovoltaic cell width constant. In addition, the focal height, number of mirrors, mirror width, and mirror spacing were also kept constant; so, the cost of the two configurations was the same from the point of view of the primary reflector system. The new design ensured the uniform distribution of solar irradiation and significantly reduced the height of the cavity. The significant decrease in the height of the proposed cavity has the following advantages: (i) a decrease in the dimensions of the fixed structure of the small-scale linear Fresnel reflector, thus reducing its cost, (ii) a significant decrease in the surface area exposed to wind loads, thus reducing the cost of the fixed structure and secondary system structures, (iii) a reduction in the difficulty of the manufacture, maintenance, and transportation of the cavity's reflecting walls, and (iv) an increase in the cooling surface area, which increases the electrical efficiency of the photovoltaic cells. [ABSTRACT FROM AUTHOR]

The objective of this paper is the investigation of the annual performance of a solar power plant with linear Fresnel reflectors in the El-Oued region at Algeria. The solar collectors produce water steam that feeds a turbine to produce electricity. The System Advisor Model (SAM) tool is used for simulation. The mean net daily electricity production rate from 8:30 am to 5:30 pm is 48 MWe, and the respective annual production is 210,336 MWh/year. The mean daily optical efficiency of the solar field was close to 52%, while the mean thermal efficiency was about 39%. The net daily cycle efficiency is found to be 24%. The net capital cost of the examined system is $393 million, and the developer net present value is $47 million; the investor net present value is $15 million, the entire period of capital recovery is 11 years, and the levelized cost of electricity is 0.0382 $/kWh. The solar power plant leads to the yearly avoidance of 420,672 tons carbon dioxide emissions (operational cost savings of $6.1 million). Based on the obtained results, linear Fresnel reflectors can be used to achieve satisfying, energetic, financial, and environmental performance that can lead to sustainability. [ABSTRACT FROM AUTHOR]

The main objective of this study is to conduct a controlled thermal investigation of a small Parabolic Trough Concentrator (PTC) under real climatic conditions for El-Oued region on 16/03/2018, where the water was adopted as a heat transfer fluid. One-dimensional and transient energy balance equations have been analyzed, simplified and then programmed with the Matlab code. What distinguishes this study is the precise tracking of all heat coefficients that would give an accurate representation of the thermal behavior of the studied device. The average optical efficiency of the device has reached 78.55 %, the average value of the thermal efficiency has reached 74.30 %, while the average value of the overall coefficient of the thermal loss is 5.96 W/m²°C. Water steam has been formed under the effect of practical conditions between 10:20 and 11:50. The results obtained in this study encouraged the research team to start manufacturing this device with the dimensions mentioned in this paper, in order to direct this prototype setup to conduct scientific experiments will be in the field of solar cooling, desalination, water heating and other areas that serve the society welfare and maintain the environment integrity. [ABSTRACT FROM AUTHOR]

Going forward towards developing and improving renewable energies in Algeria is one of the main objectives of this study, especially, solar energy that is an exceptional and continuous source of energy. Algerian Sahara has a large area suitable for agriculture, but not connected to the electricity network. Therefore, the construction of solar power plants based on the solar energy concentration has been proposed for the electricity production, which is exploited in the rest of the economic sector of the Algerian state. Through the study conducted under real weather data for the day March 16th, 2018, an optical characterization of a solar power plant of parabolic trough concentrator has been convoyed in El-Oued region, Algeria. The geometrical and the optical characteristics of studied solar collector have been determined, such as the optical efficiency, the local concentration ratio, the cosine effect of the incidence angle, the optical losses at the ends of the receiver tube, the shading effect, the blocking effect, and the coefficient of incidence angle modifier and intercept factor. MATLAB code has been used as a program for numerical programming. Of the most important results obtained, it was found that the optical efficiency has exceeded 77.22 %. As for the local concentration ratio, its maximum value is equal to 116.30 in the lower part of the receiver tube at the peripheral receiver angles "ß=91° and 269°", while the minimum values of this important coefficient were recorded at the top of the receiver tube. [ABSTRACT FROM AUTHOR]

In order to understand the behavior and to determine the effective operational parameters of a solar-driven ejector air conditioning system at low or medium temperature, a dynamic model depends on the principles of conservation, the momentum mass and energy is developed. For this purpose, the thermodynamic characteristics of the liquid and vapor refrigerant were identified using the Engineering Equation Solver (EES) software. Linear Fresnel solar reflector has been used as a tool to convert solar energy into thermal energy. Water (R718) was used as a refrigerant. The operational conditions for the studied solar-driven ejector air conditioning system are as follows: evaporator temperature "Te =283.15 K", condenser temperature "Tc =305.15 K", and generator temperature "Tg = 373.15 K". The performance of the ejector air conditioning system was compared as a function of the operating parameters of the subsystem. The average value of thermal efficiency of the Fresnel linear concentrator has reached 31.60 %, the drive ratio "ω" is 0.4934, the performance value of the ejector air conditioning subsystem "COPejc" is 60.664 % and the average value of the thermal performance of the machine "STR" has touched 19.17 %. The results obtained through this scientific subject are stimulating and encouraging, where this technique can be used for air conditioning in desert areas in southern Algeria, where fossil energy (petroleum, gas, etc.) is extracted and produced in various types. [ABSTRACT FROM AUTHOR]

The present study is a 4E (Energy, Exergy, Economic, and Environmental) analysis of a nanofluid-based parabolic trough collector (PTC) which is conducted with a developed model in MATLAB. MXene (Ti 3 C 2) nanoparticles were added to the silicon oil at weight concentrations of 0.05, 0.08, and 0.1%. The result was the important enhancement of the thermal conductivity of the nanofluid on the rand of 70%–89% for the highest concentration. According to the results, the PTC's optical efficiency was estimated at 79%, while thermal and exergy efficiencies of 74.71% and 22.44% with 0.10 wt% concentration were recorded on July 17, 2019. It is found that the MXene based silicone oil can reduce the system's cost by 0.021 M$ and enhance the energy gained by 1.51% at 0.10 wt% concentration compared to pure oil. Also, the annual CO 2 mitigation from the energy side varies from 2.25 to 2.30-ton CO 2 /year, while the annual environmental gain ranged between 32.73 and 33.28 $/year and 9.065 to 9.102 $/year for the energy and exergy studies respectively. [Display omitted] • A nanofluid-based parabolic trough collector is studied with MXene. • The collector thermal efficiency enhancement is found up to 1.1%. • For the day July 17, 2019, the exergy efficiency was improved from 0.07% to 15.16%. • For energy analysis, the annual CO 2 mitigation varies from 2.26 to 2.30 ton CO 2. • The environmental gain from the energy analysis varies from 32.73 to 33.28 $/year. [ABSTRACT FROM AUTHOR]