Search

The choice of a material for a given application requires insuring a good durability in its conditions of employment, in particular environmental. It is especially true for the systems destined to work in corrosive hot atmospheres. For it, the knowledge and the understanding of the corrosion phenomena, oxidization, ageing and damage are indispensable in order to anticipate the life period of the structures and to propose the adapted protective solutions. The study of the corrosion in high temperature is therefore a greatly interdisciplinary topic, into the interface of the physico-chemistry, metallic and ceramic materials and mechanics. We propose in this work a finite element method for the simulation of EBPVD TBCs spallation. Our studies concern one of several systems that we call thermal barrier coatings, which are a Composite materials deposited in layers on the hot components to isolate them chemically and thermally at high temperatures. This is the last operational technology adapted on aircraft engines but it is still studied and not fully exploited.This comprehensive article describes the systems currently used and the problem of interaction between mechanical and environment in the turbine.

The current study addresses the impact of the addition of fullerene and graphene nanoparticles on the AC breakdown voltage (AC BdV) of natural ester (FR3). The nanofluids (NFs) were prepared following the two-step process, and the AC BdV was performed in compliance with IEC 60156 standards. Five different concentrations of NPs were considered (0.1 g/L, 0.2 g/L, 0.3 g/L, 0.4 g/L, and 0.5 g/L). A Student's t-test was performed to compare the base liquid's AC BdV data with different nanofluids. The experimental data were checked to see if they obeyed the Weibull distribution fitting curve, and the AC BdV at 1%, 10%, and 50% risk levels were then calculated. The performed t-test provides evidence that AC BdV data from the base liquid were different from those of different NFs (except 0.2 g/L fullerene, and 0.1 g/L and 0.4 g/L graphene NFs). It is also shown that the Weibull distribution fit the BdV data of all liquids (except 0.5 g/L fullerene NF), and remarkable improvements of AC BdVs at 1%, 10%, and 50% were observed. The best improvement was obtained with 0.4 g/L fullerene and 0.3 g/L graphene NFs. These results show the importance of using nanofluids as substitutes for the existing insulating liquids for current oil-filled power transformers. [ABSTRACT FROM AUTHOR]

This paper is aimed at studying the influence of conducting (Fe3O4), semi-conductive (ZnO), and insulating (ZrO2, SiO2, and Al2O3) nanoparticles (NPs) at various concentrations on the AC dielectric strength of MIDEL 7131 synthetic ester (SE) and partial discharges activity. First, a detailed and improved procedure for preparing nanofluids (NFs) in five concentrations ranging from 0.1 g/L to 0.5 g/L is presented, including high-speed agitation and ultrasonication. Then, the long-term stability is checked based on zeta potential analysis. After preparing and characterizing the NF samples, the following step is to measure their AC breakdown voltage (BDV). Due to the limitation of the high voltage supply (Baur system), the tests are performed according to IEC 60156 standard (2.5 mm gap distance) only with ZnO, ZrO2, and SiO2 NPs, and for comparison, tests are executed for all considered NPs with an electrodes gap of 2 mm. It is shown that the addition of Fe3O4 (20 nm), ZnO (25 nm), ZrO2 (20–30 nm), SiO2 (10–20 nm), Al2O3 (20–30 nm), and Al2O3 (50 nm) NPs improves the dielectric strength of synthetic ester upon an optimal concentration which gives the highest AC BDV. SiO2 (10–20 nm) and Al2O3 (20–30 nm) manifest their best improvement at 0.3 g/L, while for the other NFs, the best improvement is observed at 0.4 g/L. Further, the Anderson–Darling goodness-of-fit test is performed on the experimental data to check their conformity with the Extreme value (EV), normal, and Weibull distributions; the normal and EV fit curves are plotted and used to evaluate the breakdown voltages at probabilities of 1%, 10%, and 50%. It is shown that the AC breakdown voltage outcomes for most investigated nanofluids mostly obey the three EV, normal, and Weibull distributions. Then, the best combinations (nature of NP and optimal concentration), namely Fe3O4 (20 nm, 0.4 g/L), Al2O3 (20–30 nm, 0.3 g/L), and Al2O3 (50 nm, 0.4 g/L) NPs, that highly enhance the AC BDV of SE are chosen for a partial discharge activity investigation and comparison with pure SE. It is shown that the addition of those NPs significantly reduces the activity of partial discharges compared to pure SE. [ABSTRACT FROM AUTHOR]