Search

Self‐charging power systems (SCPSs) are envisioned as promising solutions for emerging electronics to mitigate the increasing global concern about battery waste. However, present SCPSs suffer from large form factors, unscalable fabrication, and material complexity. Herein, a type of highly stable, eco‐friendly conductive inks based on poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) are developed for direct ink writing of multiple components in the SCPSs, including electrodes for miniaturized spacer‐free triboelectric nanogenerators (TENGs) and microsupercapacitors (MSCs), and interconnects. The principle of "one ink, multiple functions" enables to almost fully print the entire SCPSs on the same paper substrate in a monolithic manner without post‐integration. The monolithic fabrication significantly improves the upscaling capability for manufacturing and reduces the form factor of the entire SCPSs (a small footprint area of ≈2 cm × 3 cm and thickness of ≈1 mm). After pressing/releasing the TENGs for ≈79000 cycles, the 3‐cell series‐connected MSC array can be charged to 1.6 V while the 6‐cell array to 3.0 V. On‐paper SCPSs are promising to serve as lightweight, thin, sustainable, and low‐cost power supplies. [ABSTRACT FROM AUTHOR]

The drawbacks of amorphous hard carbon are its low conductivity and structural instability, due to its large volume change and the occurrence of side reactions with the electrolyte during cycling. Here, we propose a simple and rapid method to address these disadvantages; we used an emulsion solvent–evaporation method to create hierarchically structured microparticles of hard carbon nanoparticles, derived from soot, and multi-walled-carbon-nanotubes at a very low threshold of 2.8 wt%. These shrub-ball like microparticles have well-defined void spaces between different nanostructures of carbon, leading to an increased surface area, lower charge-resistance and side reactions, and higher electronic conductivity for Na+ insertion and de-insertion. They can be slurry cast to assemble Na+ anodes, exhibiting an initial discharge capacity of 713.3 mA h g−1 and showing long-term stability with 120.8 mA h g−1 at 500 mA g−1 after 500 cycles, thus outperforming neat hard carbon nanoparticles by an order of magnitude. Our work shows that hierarchical self-assembly is attractive for increasing the performance of microparticles used for battery production. [ABSTRACT FROM AUTHOR]

Monodispersed hairy nanocomposites with typical 2 nm (isophthalic acid)24Cu24 metal–organic polyhedra (MOP) as a core protected by 24 polymer chains with controlled narrow molecular weight distribution has been probed by imaging and scattering studies for the heterogeneity of polymers in the nanocomposites and the confinement effect the MOPs imposing on anchored polymers. Typical confined‐extending surrounded by one entanglement area is proposed to describe the physical states of the polymer chains. This model dictates the counterintuitive thermal and rheological properties and prohibited solvent exchange properties of the nanocomposites, whilst those polymer chain states are tunable and deterministic based on their component inputs. From the relationship between the structure and behavior of the MOP nanocomposites, a MOP‐composited thermoplastic elastomer was obtained, providing practical solutions to improve mechanical/rheological performances and processabilities of inorganic MOPs. [ABSTRACT FROM AUTHOR]

Deuterium labeling of semi‐crystalline polymers can dramatically affect their crystallization behaviors. However, the influence of different labeled positions in a partially deuterated polymer on its crystallization is still far from understood. Here, we synthesized a series of selectively deuterated poly(ε‐caprolactones) (PCLs) through ring‐opening polymerization of ε‐caprolactone with controlled deuteration sites, including fully protiated (D0), fully deuterated (D10), tetra deuteration at the 3‐ and 7‐ caprolactone ring positions (D4) and hexa deuteration at the 4‐, 5‐, and 6‐ caprolactone ring positions (D6). All the PCLs showed a similar lamellar structure and parameters. Differential scanning calorimetry (DSC) analysis revealed that the equilibrium melting temperature Tm0, melting temperature Tm, crystallization temperature Tc, and crystallization kinetics changed systemically with the deuterium content except for D4, which indicates that the presence of CD2 moieties on either side of ester group in the polymer chain combined with isotopic inhomogeneity could influence the chain packing. The nonmonotonic trend of Tm as a function of deuterium content could be attributed to the difference in a hydrogen‐bond like intermolecular interaction between different PCLs. Partially deuterated PCLs (D4 and D6) showed an Avrami index near 2. After analyzing the parameters at the same supercooling temperature ΔTc, the existence of two crystallization regimes of PCLs were detected. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019, 57, 771–779 [ABSTRACT FROM AUTHOR]

Fully biodegradable and renewable polymer materials have shown broad application prospects with minimal environmental degradation. In the current study, eco-friendly poly(lactic acid)/poly(butylene adipate-co-terephthalate) (PLA/PBAT) in-situ nanofibrillar composites with hierarchical crystal architectures, high mechanical performance and excellent heat resistance properties were fabricated using the loop oscillating push-pull molding (LOPPM) technique and in-situ PBAT nanofibrils were used to induce highly oriented hybrid shish-kebabs. Benefiting from the flow-induced crystallization and abundant hybrid shish-kebabs, the overall crystallinity of LOPPM-processed PLA/10 wt%PBAT sample increased by 4-fold than the conventional injection-molded (CIM) neat PLA sample. The present work indicated that the tensile strength, Young's modulus, elongation at break and impact strength of LOPPM-processed PLA/10 wt%PBAT were higher than the CIM-processed PLA by 36.2%, 12.5%, 181.8% and 253.7%, respectively. The vicat softening temperature was elevated from 59.6 °C to 104.8 °C, and the thermostability also enhanced due to the construction of hybrid shish-kebabs. Strong, tough and heat-resistant PLA/PBAT in situ nanofibrillar composites exhibited outstanding properties for use under more demanding circumstances and are environmentally friendly. • High performance PLA/PBAT in-situ nanofibrillar composites were prepared by means of LOPPM technique. • The intense oscillating shear flow field improved the interfacial adhesion of the immiscible PLA and PBAT. • The in-situ PBAT nanofibrils facilitated the formation of PLA/PBAT hybrid shish-kebabs. • The enriched shish-kebabs endowed products good strength, high toughness, outstanding heat resistance and thermostability. [ABSTRACT FROM AUTHOR]

The nature of mass transport in plants has recently inspired the development of low-cost and sustainable wood-based electronics. Herein, we report a wood electrochemical transistor (WECT) where all three electrodes are fully made of conductive wood (CW). The CW is prepared using a two-step strategy of wood delignification followed by wood amalgamation with a mixed electron-ion conducting polymer, poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS). The modified wood has an electrical conductivity of up to 69 Sm -1 induced by the formation of PEDOT:PSS microstructures inside the wood 3D scaffold. CW is then used to fabricate the WECT, which is capable of modulating an electrical current in a porous and thick transistor channel (1 mm) with an on/off ratio of 50. The device shows a good response to gate voltage modulation and exhibits dynamic switching properties similar to those of an organic electrochemical transistor. This wood-based device and the proposed working principle demonstrate the possibility to incorporate active electronic functionality into the wood, suggesting different types of bio-based electronic devices.

Monodispersed hairy nanocomposites with typical 2 nm (isophthalic acid) 24 Cu 24 metal-organic polyhedra (MOP) as a core protected by 24 polymer chains with controlled narrow molecular weight distribution has been probed by imaging and scattering studies for the heterogeneity of polymers in the nanocomposites and the confinement effect the MOPs imposing on anchored polymers. Typical confined-extending surrounded by one entanglement area is proposed to describe the physical states of the polymer chains. This model dictates the counterintuitive thermal and rheological properties and prohibited solvent exchange properties of the nanocomposites, whilst those polymer chain states are tunable and deterministic based on their component inputs. From the relationship between the structure and behavior of the MOP nanocomposites, a MOP-composited thermoplastic elastomer was obtained, providing practical solutions to improve mechanical/rheological performances and processabilities of inorganic MOPs., (© 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The severe water contamination caused by oil leakage is calling for low-cost and high-performance absorbent materials for selective oil removal. In this study, a scalable green method was proposed to produce polypropylene (PP)/poly(tetrafluoroethylene) (PTFE) composite foams via conventional processing techniques including twin-screw extrusion and supercritical carbon dioxide foaming. To produce the superhydrophobic foam, micro- and nanosized PTFE particles were melt blended with PP and subsequently foamed. Ascribed to the nanofibrillation of microsized PTFE during processing, the fabricated foam exhibited a special highly porous structure with PTFE nanofibrils and nanoparticles uniformly distributed on the pore surfaces within the PP matrix, which resulted in a remarkably high water contact angle of 156.8° and a low contact angle hysteresis of 1.9°. Unlike traditional surface-modified superhydrophobic absorbers, the foams prepared are entirely superhydrophobic, which means that they remain superhydrophobic when being fractured or cut. Moreover, they are highly durable and maintained the superhydrophobicity when subjected to ultrasonication and mechanical sanding. When used in selective oil absorption, the durable foams exhibited excellent absorption efficiency and high stability in repetitive and long-term use. These advantages make the PP/PTFE foam a promising superabsorbent material for water remediation.

Highly efficient proton conductors, polyoxometalate-poly(ethylene glycol) (POM-PEG) hybrid nanocomposites, have been synthesized by encapsulating a single PEG chain inside the 1D nanochannel defined by the frameworks of POMs. By employing two types of neutron scattering techniques complemented by thermal analysis, we prove that in a nanochannel a single PEG chain stays as a distorted helix. More importantly, we reveal that the PEG segments perform a localized longitudinal random walk and quantitatively show the strong correlation between the local motion of PEG and the macroscopic proton conduction of the material. On the basis of these spatial-temporal characteristics, a microscopic picture for the proton conduction process of POM-PEG hybrid materials is proposed.

Poly(lactic acid) (PLA) foams, with the combination of shish-kebab and spherulite nanoporous structure in skin and core layer respectively, was prepared using a novel technique comprising loop oscillating push-pull molding (LOPPM) and supercritical carbon dioxide low-temperature foaming process (SC-CO 2 LTFP). The foams present superior impact toughness which is 6-fold higher than that of neat PLA, and no significant decrease was observed for the storage modulus. Moreover, SC-CO 2 LTFP at soaking temperature ranging from 110 to 150 °C were performed to determine the evolution of pore morphology. The ultratough and supermoduli are unprecedented for PLA, and are in great need for broader applications.