15 results on '"Manzaneque, Tomas"'
Search Results
2. Method to Determine the Closed-Loop Precision of Resonant Sensors From Open-Loop Measurements.
- Author
-
Manzaneque, Tomas, Steeneken, Peter G., Alijani, Farbod, and Ghatkesar, Murali K.
- Abstract
Resonant sensors determine a sensed parameter by measuring the resonance frequency of a resonator. For fast continuous sensing, it is desirable to operate resonant sensors in a closed-loop configuration, where a feedback loop ensures that the resonator is always actuated near its resonance frequency, so that the precision is maximized even in the presence of drifts or fluctuations of the resonance frequency. However, in a closed-loop configuration, the precision is not only determined by the resonator itself, but also by the feedback loop, even if the feedback circuit is noiseless. Therefore, to characterize the intrinsic precision of resonant sensors, the open-loop configuration is often employed. To link these measurements to the actual closed-loop performance of the resonator, it is desirable to have a relation that determines the closed-loop precision of the resonator from open-loop characterisation data. In this work, we present a methodology to estimate the closed-loop resonant sensor precision by relying only on an open-loop characterization of the resonator. The procedure is beneficial for fast performance estimation and benchmarking of resonant sensors, because it does not require actual closed-loop sensor operation, thus being independent on the particular implementation of the feedback loop. We validate the methodology experimentally by determining the closed-loop precision of a mechanical resonator from an open-loop measurement and comparing this to an actual closed-loop measurement. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
3. GHz Broadband SH0 Mode Lithium Niobate Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Yang, Yansong, Li, Ming-Huang, Manzaneque, Tomas, and Gong, Songbin
- Subjects
DELAY lines ,INSERTION loss (Telecommunication) ,SIGNAL processing ,THIN films ,LITHIUM niobate ,MICROELECTROMECHANICAL systems - Abstract
We present the first group of GHz broadband SH0 mode acoustic delay lines (ADLs). The implemented ADLs adopt unidirectional transducer designs in a suspended X-cut lithium niobate thin film. The design space of the SH0 mode ADLs at GHz is first theoretically investigated, showing that the large coupling and sufficient spectral clearance to adjacent modes collectively enable the broadband performance of SH0 delay lines. The fabricated devices show 3-dB fractional bandwidth ranging from 4% to 34.3% insertion loss between 3.4 and 11.3 dB. Multiple delay lines have been demonstrated with center frequencies from 0.7 to 1.2 GHz, showing great frequency scalability. The propagation characteristics of SH0 in lithium niobate thin film are experimentally extracted. The demonstrated ADLs can potentially facilitate broadband signal processing applications. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
4. Gigahertz Low-Loss and Wideband S0 Mode Lithium Niobate Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Li, Ming-Huang, and Gong, Songbin
- Subjects
- *
LITHIUM niobate , *DELAY lines - Abstract
We present the first group of gigahertz S0 mode low loss and wideband acoustic delay lines (ADLs). The ADLs use a single-phase unidirectional transducers (SPUDT) design to launch and propagate the S0 mode in an X-cut lithium niobate thin film with large electromechanical coupling and low damping. In this work, the theoretical performance bounds of S0 mode ADLs are first investigated, significantly surpassing those in state-of-the-art. The design tradeoffs of S0 mode ADLs, when scaled to the gigahertz frequency range, are also discussed. The fabricated miniature ADLs show a fractional bandwidth (FBW) of 4% and a minimum insertion loss (IL) of 3.2 dB, outperforming the incumbent surface acoustic wave (SAW) counterparts, and covering a wide range of delays from 20 to 900 ns for digitally addressable delay synthesis. Multiple ADLs with center frequencies from 0.9 to 2 GHz have been demonstrated, underscoring their great frequency scalability. The propagation properties of S0 waves in lithium niobate at the gigahertz range are experimentally extracted. The demonstrated ADLs can potentially enable wide-range and high-resolution delay synthesis that is highly sought after for the self-interference cancellation in full-duplex radios. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
5. Low-Loss and Wideband Acoustic Delay Lines.
- Author
-
Manzaneque, Tomas, Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
ACOUSTIC delay lines , *THIN-film circuits , *BANDWIDTHS , *TRANSDUCERS , *FLUCTUATIONS (Physics) - Abstract
This paper demonstrates low-loss acoustic delay lines (ADLs) based on shear-horizontal waves in thin-film LiNbO3 for the first time. Due to its high electromechanical coupling, the shear-horizontal mode is suited for producing devices with large bandwidths. Here, we show that shear-horizontal waves in LiNbO3 thin films are also excellent for implementing low-loss ADLs based on unidirectional transducers. The high acoustic reflections and large transducer unidirectionality induced by the mechanical loading of the electrodes on a LiNbO3 thin film provide a great tradeoff between delay line insertion loss and bandwidth. The directionality for two different types of unidirectional transducers has been characterized. Delay lines with variations in the key design parameters have been designed, fabricated, and measured. One of our fabricated devices has shown a group delay of 75 ns with an IL below 2 dB over a 3-dB bandwidth of 16 MHz centered at 160 MHz (fractional bandwidth = 10%). The measured insertion loss for other devices with longer delays and different numbers of transducer cells are analyzed, and the loss contributing factors and their possible mitigation are discussed. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
6. A Radio Frequency Nonreciprocal Network Based on Switched Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Gao, Liuqing, Gao, Anming, and Gong, Songbin
- Subjects
- *
ACOUSTIC delay lines , *CIRCULATORS (Electrical engineering) , *DESIGN , *INSERTION loss (Telecommunication) , *LITHIUM niobate - Abstract
This paper demonstrates the first nonreciprocal network based on switched low-loss acoustic delay lines. The four-port circulator is built upon a recently reported frequency-independent, programmable, nonreciprocal framework based on switched delay lines. The design space for such a system, including the origins of the insertion loss (IL) and harmonic responses, is theoretically investigated, illustrating that the key to better performance and low-cost modulation signal synthesis lies in a large delay. To implement a large delay, we resort to in-house fabricated low-loss, wideband lithium niobate (LiNbO3)SH0 mode acoustic delay lines employing single-phase unidirectional transducers. The four-port circulator, consisting of two switch modules and one delay line module, has been modularly designed, assembled, and tested. The design process employs time-domain full circuit simulation, and the results match well with measurements. An 18.8-dB nonreciprocal contrast between IL (6.6 dB) and isolation (25.4 dB) has been achieved over a fractional bandwidth of 8.8% at a center frequency 155 MHz, using a record low switching frequency of 877.19 kHz. The circulator also shows 25.9-dB suppression for the intramodulated tone and 30 dBm for IIP3. Upon further development, such a system can potentially lead to future wideband, low-loss chip-scale nonreciprocal radio frequency systems with unprecedented programmability. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
7. Accurate Extraction of Large Electromechanical Coupling in Piezoelectric MEMS Resonators.
- Author
-
Lu, Ruochen, Li, Ming-Huang, Yang, Yansong, Manzaneque, Tomas, and Gong, Songbin
- Subjects
MEMS resonators ,QUALITY factor ,MICROELECTROMECHANICAL systems ,CRYSTAL resonators ,LITHIUM niobate ,OPTOMECHANICS ,EXTRACTION techniques ,RESONATORS - Abstract
Recent advancements in the field of piezoelectric micro-resonators have produced devices, such as lithium niobate laterally vibrating resonators, with very high electromechanical coupling factors ($k_{t}^{2}$) and respectable quality factors (${Q}$). As a result, the records of the figure of merit (FoM) for radio-frequency MEMS resonators have been broken several times in the past five years. As exciting as these high FoMs are, they impose unique caveats in accurately extracting the electromechanical coupling often due to the presence of spurious modes. It is a less noted issue for micro-resonators with moderate ${k} _{t}^{2}$ , as spurious modes either are absent or do not significantly affect the common extraction technique based on identifying resonances and anti-resonances. This paper will first theoretically analyze how disregarding spurious modes can potentially lead to inaccurate extraction of ${k} _{t}^{2}$ of the intended mode and then offer a framework that accounts for spurious modes and accurately extracts electromechanical coupling using a multi-resonance recursive fitting. [2018-0209] [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
8. Nanowatt-Level Wakeup Receiver Front Ends Using MEMS Resonators for Impedance Transformation.
- Author
-
Bassirian, Pouyan, Moody, Jesse, Roy, Abhishek, Scott Barker, N., Calhoun, Benton H., Bowers, Steven M., Lu, Ruochen, Gao, Anming, Manzaneque, Tomas, and Gong, Songbin
- Subjects
CMOS transceivers ,MICROELECTROMECHANICAL systems ,LITHIUM niobate ,ELECTRIC potential ,BANDWIDTHS - Abstract
This paper presents the first demonstration of nanowatt-level CMOS wakeup receiver (WuRx) front ends (FEs) that utilize microelectromechanical system (MEMS)-based matching networks (MNs). The first FE uses a fully MEMS-based MN (MMN) that operates at 88.8 MHz. It consists of a large array of lithium niobate resonators that are fabricated on the same die. Measurements of the integrated WuRx FE with the MMN indicate that its loaded voltage gain achieves a bandwidth of 0.78 MHz with a quality factor of 114. The second FE uses a hybrid MN (HMN) that operates at 457 MHz. It consists of an aluminum nitride laterally vibrating resonator as well as eight discrete inductors and capacitors surrounding the MEMS device. Measurements of the integrated WuRx FE with the HMN indicate that it achieves a sensitivity of −54 dBm with 7 nW of average dc power consumption without a digital correlator. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
9. RF Filters with Periodic Passbands for Sparse Fourier Transform-Based Spectrum Sensing.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Zhou, Jin, Hassanieh, Haitham, and Gong, Songbin
- Subjects
- *
FOURIER transforms , *RESONATORS , *ACOUSTICS , *MICROELECTROMECHANICAL systems , *PIEZOELECTRICITY - Abstract
This paper demonstrates a passive low-insertion-loss (IL) RF filter with periodic passbands and capable of sparsifying the spectrum from 238 to 526 MHz for sparse Fourier transform (SFT)-based spectrum sensing. The demonstrated periodic filter employs LiNbO3 lateral overtone bulk acoustic resonators (LOBARs) with high-quality factors (Qs), large electromechanical coupling ($k_{t}^{2}$), and multiple equally spaced resonances in a ladder topology. To demonstrate the periodic filter, the LOBARs is first modeled to predict $k_{t}^{2}$ of various tones accurately. The fabricated LOBARs show $k_{t}^{2}$ larger than 1.5% and figure of merits ($Q\cdot k_{t}^{2}$) more than 30 for over 10 tones simultaneously, which agree with our modeled response, and are both among the highest demonstrated in overmoded resonators. The multi-band filter centered at 370 MHz has then been obtained with a passband span of 291 MHz, a spectral spacing of 22 MHz, an IL of 2 dB, FBWs around 0.6%, and a sparsification ratio between 7 and 15. An out-of-band rejection around 25 dB has also been achieved for more than 14 bands. The great performance demonstrated by the RF filter with 14 useable periodic passbands will serve to enable future SFT-based spectrum sensing. [2018-0155] [ABSTRACT FROM AUTHOR]
- Published
- 2018
- Full Text
- View/download PDF
10. Low Phase Noise RF Oscillators Based on Thin-Film Lithium Niobate Acoustic Delay Lines.
- Author
-
Li, Ming-Huang, Lu, Ruochen, Manzaneque, Tomas, and Gong, Songbin
- Subjects
PHASE noise ,LITHIUM niobate ,DELAY lines ,ACOUSTIC surface waves ,LAMB waves ,NONLINEAR oscillators - Abstract
An RF oscillator has been demonstrated using a wideband SH
0 mode lithium niobate acoustic delay line (ADL). The design space of the ADL-based oscillators is theoretically investigated using the classical linear time-invariant (LTI) phase noise model. The analysis reveals that the key to low phase noise is low insertion loss (IL), large delay (τG ), and high carrier frequency (ƒo ). Two SH0 ADL oscillators based on a single SH0 ADL (fo = 157 MHz, IL = 3.2 dB, ƒG = 270 ns) but with different loop amplifiers have been measured, showing low phase noise of −114 dBc/Hz and −127 dBc/Hz at 10-kHz offset with a carrier power level of −8 dBm and 0.5 dBm, respectively. These oscillators not only have surpassed other Lamb wave delay oscillators but also compete favorably with surface acoustic wave (SAW) delay line oscillators in performance. [2019-0223] [ABSTRACT FROM AUTHOR]- Published
- 2020
- Full Text
- View/download PDF
11. Lithium Niobate Phononic Crystals for Tailoring Performance of RF Laterally Vibrating Devices.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, and Gong, Songbin
- Subjects
- *
LITHIUM niobate crystallography , *PHONONIC crystals , *BAND gaps , *RADIO frequency , *VIBRATION (Mechanics) - Abstract
This paper reports the first demonstration of phononic crystals (PnCs) in suspended lithium niobate thin films, which exhibit band gaps for tailoring the performance of laterally vibrating devices. Transmission and reflection properties of lithium niobate PnCs for both shear-horizontal (SH0) and length-extensional (S0) modes have been investigated and subsequently explored in two applications. In the first case, PnC-embedded delay lines were designed for filtering with stopbands, while in the second case, PnC-bounded resonators were implemented for spurious mode suppression. Equivalent circuit models incorporating acoustic scattering parameters of the designed PnCs and Mason’s model of the transducers have been built for each application. Benchmarked to reference devices without PnCs, the measured PnCs embedded in delay lines show 20-dB attenuation in the stopbands and less than 2-dB loss in the passbands for the SH0 mode, and 30-dB attenuation in the stopbands and less than 10-dB loss in the passbands for the S0 mode. The fabricated piezoelectric PnC-bounded resonator has shown a quality factor of 434 at 142.7 MHz with undesired spurious modes significantly suppressed. These demonstrations show that lithium niobate PnCs for laterally vibrating devices can potentially lead to wideband and low-loss acoustic functions for radio frequency signal processing. [ABSTRACT FROM AUTHOR]
- Published
- 2018
- Full Text
- View/download PDF
12. Lithium Niobate MEMS Chirp Compressors for Near Zero Power Wake-Up Radios.
- Author
-
Manzaneque, Tomas, Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
RADIO frequency , *TRANSDUCERS , *ELECTRONICS , *BANDWIDTHS , *SIGNAL processing - Abstract
This paper presents the first demonstration of chirp compressors based on laterally vibrating modes in suspended lithium niobate thin films. Both shear-horizontal and length-extensional modes have been explored and demonstrated with the electromechanical coupling coefficients of 30% and 39%, respectively, in a double-dispersive delay line structure. The high electromechanical coupling, along with the low propagation loss in the suspended thin film, produces a low insertion loss of 10 dB over a large fractional bandwidth of 50%. The best fabricated device demonstrates a delay-bandwidth product of 100, and provides a voltage gain of 5 to the corresponding chirp signals. Moreover, significant signal-to-noise ratio enhancements (>100), collectively enabled by the processing gain and filtering characteristics of the chirp compressors, have been demonstrated. The measured devices, in this paper, greatly outperform state-of-the-art chirp compressors based on surface acoustic waves in insertion loss for a comparable TB. As a result, signal-to-noise ratio enhancement and voltage gain have been simultaneously demonstrated for the first time in a passive device and the analog domain. The high performance can be harnessed to greatly enhance the sensitivity of near zero power wake-up radio receivers and enable low-power wireless connectivity for Internet of Things applications. [2017–0126] [ABSTRACT FROM PUBLISHER]
- Published
- 2017
- Full Text
- View/download PDF
13. Density-viscosity sensor based on piezoelectric MEMS resonator and oscillator circuit.
- Author
-
Manzaneque, Tomas, Ruiz-Diez, Victor, Hernando-Garcia, Jorge, Wistrela, Elisabeth, Kucera, Martin, Schmid, Ulrich, and Luis Sanchez-Rojas, Jose
- Published
- 2014
- Full Text
- View/download PDF
14. Multimodal characterisation of high‐Q piezoelectric micro‐tuning forks.
- Author
-
Gil, Marta, Manzaneque, Tomas, Hernando‐García, Jorge, Ababneh, Abdallah, Seidel, Helmut, and Sánchez‐Rojas, Jose Luis
- Abstract
This work presents an electrically actuated, aluminium nitride based, piezoelectric tuning fork designed at the micro‐scale for selective modal actuation. This well known resonator, whose advantages have been widely studied and exploited in the milli‐scale, has been implemented and studied in the micro‐scale, showing promising results. A complete optical and electrical characterisation of the device has been carried out, in which various out‐of‐plane and in‐plane vibration modes have been analysed. Its performance has been studied in vacuum, air and water. High‐quality factors (Qs) up to 72 in water and up to 5166 in air have been measured for the in‐plane anti‐phase mode. This Q‐factor is higher than any other value published with the in‐plane piezoelectric micro‐cantilevers in air. Sensitivity as mass sensor and minimum detectable mass has also been estimated in air. Sensitivity values almost three orders of magnitude higher than millimetric commercial tuning forks have been achieved. Easy integration, simple and selective actuation and a Q make this kind of resonator an attractive alternative in a wide range of applications. [ABSTRACT FROM AUTHOR]
- Published
- 2013
- Full Text
- View/download PDF
15. Control of MEMS Vibration Modes With Pulsed Digital Oscillators—Part II: Simulation and Experimental Results.
- Author
-
Ricart, Jordi, Pons-Nin, Joan, Blokhina, Elena, Gorreta, Sergi, Hernando, Jorge, Manzaneque, Tomas, Sanchez-Rojas, Jose Luis, Feely, Orla, and Dominguez, Manuel
- Subjects
MICROELECTROMECHANICAL systems ,ELECTROMECHANICAL devices ,ELECTRIC oscillators ,RESONANCE ,VIBRATION (Mechanics) ,COMPUTER simulation - Abstract
This paper extends our previous work on the selective excitation of mechanical vibration modes in MEMS devices using pulsed digital oscillators (PDOs). It begins by presenting extensive simulation results using the set of iterative maps that model the system and showing that it is possible to activate two or three spatial modes (resonances) of the mechanical structure with a PDO. The second part of this paper presents experimental results corroborating the theory and simulation results. It is shown that it is possible to separately excite vibration modes of the device by setting a few parameters of the PDO structure such as the sampling frequency and the sign of the feedback loop. [ABSTRACT FROM PUBLISHER]
- Published
- 2010
- Full Text
- View/download PDF
Catalog
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.