Search

Smart grid and distributed generation should be the solution of the global climate change and the crisis energy of the main source of electrical power generation which is fossil fuel. In order to meet the rising electrical power demand and increasing service quality demands, as well as reduce pollution, the existing power grid infrastructure should be developed into a smart grid and distributed power generation which provide a great opportunity to address issues related to energy efficiency, energy security, power quality and aging infrastructure systems. The conventional of the existing distributed generation system is an AC grid while for a renewable resources requires a DC grid system. This paper explores the model of smart DC grid by introducing a model of smart DC grid with the stable power generation give a minimal and compressed circuitry that can be implemented very cost-effectively with simple components. The PC based application software for controlling was developed to show the condition of the grid and to control the grid become 'smart'. The model is then subjected to a severe system perturbation, such as incremental change in loads to test the performance of the system again stability. It is concluded that the system able to detect and controlled the voltage stability which indicating the ability of power system to maintain steady voltage within permissible rangers in normal condition. [ABSTRACT FROM AUTHOR]

Spin coater usually applied in preparation of a thin layer in industrial coatings and advanced material functionalization in various applications. This paper reports the development of spin coater with a closed loop control system using ATMega8535 microcontroller. The thickness of the thin film layer depend on the rotation of spin coater in which usually controlled by open-loop type. In long-term utilization of the spin coater, the performance of the motor usually degraded and caused the speed of the rotation is no longer accurate. Therefore to resolve the drawback, a closeloop system is applied in currently developed spin coater. The speed range of the spin coater was designed in between 450-6000 rpm, equipped with user interface through push button and LCD display. The rotary encoder transducer was applied to sense the speed of the dc motor. The pulse width modulation (PWM) method is applied to control the speed of the dc motor. The performance of the control system were evaluated based on the applied voltage to the PWM driver (L298) versus speed of the motor and also the rise time, overshoot, and settling time of the control system. The result shows that in the setting of low speed (450 rpm), the settling time is very fast about 12 seconds and very high overshoot about 225 rpm, contrary for the high speed (5550 rpm) the setting time is 71 seconds and very low overshot about 30 rpm. In addition, to evaluate the stability of the mechanical system, the spin coater was tested to prepare a ZnO thin film in various speed of rotations and at various concentrations of the solution, i.e. 10 wt.% and 15 wt.%. It is concluded that the spin coater can be utilized for thin film coating after pass the maximum of the settling time (71 seconds). The currently developed spin coater produce a film with common characteristics of the spin coater where thicker film was obtained when higher concentration was used and thinner the film was obtained when higher speed of the rotation was applied. [ABSTRACT FROM AUTHOR]

Chemical vapor deposition (CVD) is widely used to grow a thin film applied in many industrial applications. This paper report the development of an aerosol assisted chemical vapor deposition (AACVD) which is one of the CVD methods. Newly developed AACVD system consists of a chamber of pyrex glass, two wire-heating elements placed to cover pyrex glass, a substrate holder, and an aerosol generator using an air brush sprayer. The temperature control system was developed to prevent condensation on the chamber walls. The control performances such as the overshoot and settling time were obtained from of the developed temperature controller. Wire-heating elements were controlled at certain setting value to heat the injected aerosol toform a thin film in the substrate. The performance of as-developed AACVD system tested toform a thin film where aerosol was sprayed into the chamber with a flow rate of 7 liters/minutes, and vary in temperatures and concentrations of precursor. The temperature control system have an overshoot around 25 °C from the desired set point temperature, very small temperature ripple 2 °C and a settling time of 20 minutes. As-developed AACVD successfully fabricated a ZnO thin film with thickness of below 1 μm. The performances of system on formation of thin films influenced by the generally controlled process such as values of setting temperature and concentration where the aerosol flow rate was fixed. Higher temperature was applied, the more uniform ZnO thin films were produced. In addition, temperature of the substrate also affected on surface roughness of the obtained films, while concentration of ZnO precursor determined the thickness of produce films. It is concluded that newly simple AACVD can be applied to produce a thin film. [ABSTRACT FROM AUTHOR]

Integrating Sphere (IS) is an instrument formed a cavity sphere with its inner surface act as a Lambertian reflector. IS is needed in many optical measurements which involves a high diffused reflection. In addition, IS very essential in photometry and radiometry measurement system. However, currently, IS is still an imported product which considered very expensive. The material for the sphere and inner surface coating affect the performance of the IS systems. Therefore, the main challenges in designing IS are the material engineering for the sphere and the procedure for the inner surface coating. The inner surface was coated using BaSO4 which has a low absorption and high diffuse reflection. Spectral responses of the IS system was characterized using USB2000+ and calibrated using a standard Spectralon from ocean optic. The obtained IS system used an inner surface coating from a mixed 80% Barium Sulfate (BaSO4) and 20% Nippon Elastex paint which yield a reflection factor ρ = 0.955 and amplification factor M=10.69. The validation was conducted using an emitter with known specification from Luxeon of LXHL-DW01 which produced light flux 40.5 lumen with injection current 350 mA and junction temperature Tj 25°C. [ABSTRACT FROM AUTHOR]