Search

RF excited gas discharges of hexamethyldisiloxane (HMDSO) with and without oxygen and methane (CH4) without further carrier gas were examined to identify reaction parameters determining deposition rate and film properties of SiOx and a-C:H films, respectively. This evaluation is supported by the used reactor type which enables well-defined deposition conditions. Both symmetrical and asymmetrical electrode configurations are investigated. It is found that the deposition rate depends on the reaction parameter power input per gas flow where the gas flows of monomer and reactive carrier gases are added. Thus, O2 in conjunction with HMDSO can be considered as a film-forming gas. Even in asymmetrical discharges the concept of the reaction parameter W/F holds, as long as the increasing ion bombardment allows a continuous film growth. While W/F controls the chemical composition of the films, the potential drop across the plasma sheath influences the mechanical film properties. With these findings SiOx and a-C:H plasma coatings can be designed. [Copyright &y& Elsevier]

In this paper, parylene C coating with the thickness of 2 μm was deposited on different magnesium alloy substrates (AZ31, WE43 and AZ91). The structure and phase composition of parylene C coating was analysed by Fourier transformed infrared (FTIR) spectroscopy and X-ray diffraction (XRD). In addition, extensive surface characterization was done using atomic force microscopy. The corrosion performance of polymer-coated magnesium alloys was investigated by electrochemical measurements in Hanks’ balanced salts solution that simulates bodily fluids at 37 ± 0.5 °C. The depth-dependent mechanical properties including Young’s modulus and nanohardness of parylene C films were investigated using nanoindentation technique. The effect of the penetration depth on the properties on nano- and microscale level have been described in detail. The percentage of elastic recovery was used to characterize the elastic properties of the polymeric coatings. The results of XRD showed (020) preferred orientation of the monoclinic unit cell of the alpha phase of parylene C. The parylene C revealed a semicrystalline structure with nanocrystalline blocks of 4.9 nm. The parylene C film shows a uniform surface morphology with a higher roughness level at micro and nanoscales compared to magnesium alloy surfaces. All of the uncoated substrates exhibited a low corrosion resistance compared to the coated samples, indicating that the corrosion resistance of the magnesium alloys could be improved by parylene C coating. The resulting average nanohardness and Young’s modulus of the parylene C coatings deposited onto different substrates were in the range of 0.18–0.25 GPa and 4.19–5.14 GPa, respectively. Furthermore, a higher percentage of elastic recovery of the polymer coating indicated a higher elasticity as compared to the magnesium alloy surface. The polymer coating has revealed the ability to recover elastically. Therefore, parylene C coating can not only improve corrosion resistance, but also provide the ability to recover elastically, expanding the potential applications of this material to include various biointerface platforms. [ABSTRACT FROM AUTHOR]

The surface properties of poly-3-hydroxybutyrate (P3HB) membranes were modified using oxygen and an ammonia radio-frequency (RF, 13.56 MHz) plasma. The plasma treatment procedures used in the study only affected the surface properties, including surface topography, without inducing any significant changes in the crystalline structure of the polymer, with the exception being a power level of 250 W. The wettability of the modified P3HB surfaces was significantly increased after the plasma treatment, irrespective of the treatment procedure used. It was revealed that both surface chemistry and surface roughness changes caused by the plasma treatment affected surface wettability. A treatment-induced surface aging effect was observed and resulted in an increase in the water contact angle and a decrease in the surface free energy. However, the difference in the water contact angle between the polymers that had been treated for 4 weeks and the untreated polymer surfaces was still significant. A dependence between cell adhesion and proliferation and the polar component of the surface energy was revealed. The increase in the polar component after the ammonia plasma modification significantly increased cell adhesion and proliferation on biodegradable polymer surfaces compared to the untreated P3HB and the P3HB modified using an oxygen plasma. [ABSTRACT FROM AUTHOR]

Silicon-doped hydroxyapatite-based (Si-HA) coatings were deposited via radio frequency (RF) magnetron sputtering on the surface of titanium that was treated with a pulsed electron beam. This study aimed to evaluate the effect of Si doping on the structure and mechanical properties of thin HA films. The content of the silicon was 1.2 and 4.6 at.% for the coatings prepared using the Si-HA precursor powders with a chemical formula Ca 10 (PO 4 ) 6 − x (SiO 4 ) x (OH) 2 − x where, x = 0.5 and 1.72. Pure HA (Ca 10 (PO 4 ) 6 (OH) 2 ) coatings were deposited for comparison. The as-deposited films were analysed with respect to their composition, state of chemical binding and microstructure using XPS, FTIR, XRD, and SEM. We hypothesized that the addition of Si would affect the mechanical features of the coatings due to microstructure changes. The effect of the introduction of Si on the nanohardness and the Young's modulus as well as the adhesion strength and scratch resistance of the HA coating was investigated using nanohardness testing and a scratch test, respectively. Examination of the coating microstructure using SEM and AFM revealed that Si doping influenced the surface morphology and led to a smaller grain size. The tendency to form an amorphous structure also increased with an increase in the Si content. A monotonous decrease in both the nanohardness and the elastic modulus was observed with an increase in the Si content. A maximum nanohardness of ~ 7 GPa was obtained for the Si-free HA coating, whereas the hardness decreased to ~ 4.3 GPa for the films with a Si content of 1.2 at.%. The addition of 4.6 at.% Si to the HA coating resulted in a reduction in the elastic modulus, whereas the nanohardness was very similar to that of the uncoated substrate. The adhesion behaviour of the coatings demonstrated different responses. In the case of pure HA coatings, failure occurred due to the low cohesion of the coating, whereas the crystalline Si-HA coatings with a Si content of 1.2 at.% deformed plastically without crack formation and without detaching from the titanium substrate, which resulted in a greater coating stability. [ABSTRACT FROM AUTHOR]

Nonthermal treatment with cold atmospheric plasma (CAP) is a promising option for local treatment of chronic-inflammatory and precancerous lesions as well as various mucosal cancer diseases, besides its primary indication for wound healing and antiseptics. Atmospheric pressure plasma jets (APPJs) are versatile plasma sources, some of which are well-characterized and medically approved. The characterization of APPJs, however, is often based on the treatment of simple solutions or even studies on the plasma effluent itself. To better assess the in vivo effects of CAP treatment, this study aims to recapitulate and study the physicochemical tissue-level effects of APPJ treatment on human primary mucosal tissue and tissue models. High resolution on-tissue infrared (IR) thermography and a first-time-performed spatially resolved optical emission spectroscopy (OES) of the APPJ emissions did not identify potentially tissue-harming effects. In this study, electron-spin-resonance (ESR) spectroscopy on human tissue samples, treated with different CAP doses, enabled the measurement and the distribution of CAP-derived radicals in the tissues. The results correlate plasma dosage and the generation of radical species with cell viability and cell proliferation of primary human fibroblasts while demonstrating apoptosis-independent antiproliferative cell effects. Moreover, a dose-dependent increase of cells in the G1 phase of the cell cycle was observed, stressing the likely important role of cell cycle regulation for antiproliferative CAP mechanisms. This study introduces suitable methods for CAP monitoring on tissues and contributes to a better understanding of tissue-derived plasma effects of APPJs.

Thin radio-frequency magnetron sputter deposited nano-hydroxyapatite (HA) films were prepared on the surface of a Fe-tricalcium phosphate (Fe-TCP) bioceramic composite, which was obtained using a conventional powder injection moulding technique. The obtained nano-hydroxyapatite coated Fe-TCP biocomposites (nano-HA-Fe-TCP) were studied with respect to their chemical and phase composition, surface morphology, water contact angle, surface free energy and hysteresis. The deposition process resulted in a homogeneous, single-phase HA coating. The ability of the surface to support adhesion and the proliferation of human mesenchymal stem cells (hMSCs) was studied using biological short-term tests in vitro. The surface of the uncoated Fe-TCP bioceramic composite showed an initial cell attachment after 24h of seeding, but adhesion, proliferation and growth did not persist during 14 days of culture. However, the HA-Fe-TCP surfaces allowed cell adhesion, and proliferation during 14 days. The deposition of the nano-HA films on the Fe-TCP surface resulted in higher surface energy, improved hydrophilicity and biocompatibility compared with the surface of the uncoated Fe-TCP. Furthermore, it is suggested that an increase in the polar component of the surface energy was responsible for the enhanced cell adhesion and proliferation in the case of the nano-HA-Fe-TCP biocomposites., (Copyright © 2015 Elsevier B.V. All rights reserved.)

The control of surface properties is a substantial step in the development and improvement of biomaterials for clinical applications as well as for their use in tissue engineering. Interaction of the substrate surface with the biochemical or biological environment is crucial for the outcome of the applied biomaterial and therefore should meet specific requirements regarding the chemical composition, wettability, elasticity, and charge. In this study, we examined the effect of chemical groups introduced by low pressure plasma treatments of polystyrene surfaces on the cell behavior of primary human mesenchymal stem cells (hMSCs) and dermal microvascular endothelial cells (hDMECs). X-ray photoelectron spectroscopy analysis and contact angle measurements were employed to evaluate ammonia-, carbon dioxide-, and acrylic acid-plasma modifications to substrate surfaces. HMSCs and hDMECs were analyzed simultaneously to identify the most suitable surface functionalization for each cell type. Significantly higher cell proliferation was detected on ammonia plasma-treated surfaces. Cell-material interaction could be shown on all created interfaces as well as the expression of typical cell markers. Hence, the applied plasma treatment presents a suitable tool to improve culture condition on polystyrene for two important cell types (hMSCs and hDMECs) in the field of tissue engineering., (Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Dopamine-melanin films produced through the oxidation of dopamine in the presence of oxygen as an oxidant allow to reduce silver ions onto silver particles as already described in the paper by Lee et al. (H. Lee, S.M. Dellatore, W.M. Miller, P.B. Messersmith, Science 318 (2007) 426.). This reduction process has to occur through the oxidation of moieties present in the melanin film. This investigation shows that the free radicals present in the pseudomelanin film, quantified by means of electron spin resonance spectroscopy (ESR) for the first time, are not used in the transformation of Ag(+) cations to deposit silver. The ESR signal is hardly affected by the deposition of silver particles. On the other hand, X-ray photoelectron spectroscopy shows a small increase in the density of quinone groups and a small decrease of catechol groups on the surface of the film during the deposition of silver. This suggests that the deposited pseudomelanin films contain a significant fraction of catechol groups able to trigger reduction processes of metallic cations. These silver nanoparticles remain adherent to the melanin films and allow for a quantitative killing of Escherichia coli over a broad range of bacterial dilutions. However, the presence of the bacteria induces a release of the nanoparticles. The pseudomelanin films cannot be reused again for a silver ion reduction step. Nevertheless, the easy preparation of the pseudomelanin-silver composite and its effective one shot bacterial killing activity renders the strategy presented in this paper attractive. Some fundamental questions about redox process allowed by the pseudomelanin films will also be asked., (Copyright © 2011 Elsevier Inc. All rights reserved.)

Polysiloxane films were prepared by plasma polymerization and dip coating. Upon these films PEG was grafted by conventional methods, and ethylene oxide by plasma activation. Before and after grafting the films were analyzed by contact angle and ESCA measurements as well as by FTIR-ATR-spectroscopy and TOF-SIMS. Furthermore results of protein adsorption measurements are reported. The polysiloxane structures obtained by the plasma polymerization of HMDSO are rather similar to those ones yielded by dip coating. The two types of grafting applied on the polysiloxane substrates led to different structures of the grafted layers as was revealed by TOF-SIMS spectra.