Search

Proton exchange membranes (PEMs) with superior characteristics are needed to advance fuel cell technology. Nafion, the most used PEM in direct methanol fuel cells (DMFCs), has excellent proton conductivity but suffers from high methanol permeability and long-term performance degradation. Thus, this study aimed to create a healable PEM with improved durability and methanol barrier properties by combining sulfonated poly(ether ether ketone) (SPEEK) and poly-vinyl alcohol (PVA). The effect of changing the N,N-dimethylacetamide (DMAc) solvent concentration during membrane casting was investigated. Lower DMAc concentrations improved water absorption and, thus, membrane proton conductivity, but methanol permeability increased correspondingly. For the best trade-off between these two characteristics, the blend membrane with a 10 wt% DMAc solvent (SP10) exhibited the highest selectivity. SP10 also showed a remarkable self-healing capacity by regaining 88% of its pre-damage methanol-blocking efficiency. The ability to self-heal decreased with the increasing solvent concentration because of the increased crosslinking density and structure compactness, which reduced chain mobility. Optimizing the solvent concentration during membrane preparation is therefore an important factor in improving membrane performance in DMFCs. With its exceptional methanol barrier and self-healing characteristics, the pioneering SPEEK/PVA blend membrane may contribute to efficient and durable fuel cell systems. [ABSTRACT FROM AUTHOR]

Self‐healing proton‐exchange membranes (PEMs) made of poly(vinyl alcohol) (PVA) and Nafion were synthesized using the freeze‐thaw method. Since PVA is more selective towards water than methanol, the blend membrane successfully reduced methanol permeability and improved selectivity compared to the recast Nafion membrane. The addition of PVA also helped the membrane self‐heal by promoting the formation of hydrogen bonds. In contrast to the pristine Nafion, which exhibited even more severe methanol crossover after being damaged than before, the Nafion‐PVA membrane underwent a self‐healing process and regained much of its methanol barrier function. These advantageous characteristics of the Nafion‐PVA membrane suggest its potential use in direct methanol fuel cells (DMFCs). [ABSTRACT FROM AUTHOR]

Summary: Concentrated photovoltaic cell (CPV) is a solar energy harvesting device that converts solar energy into electrical energy. However, the performance and efficiency of the CPV are heavily dependent on the temperature. Besides, nonuniformity of temperature distribution on the CPV will lead to thermal aging and affects the cycle life. Hence, an effective cooling system is required to remove excess heat generated to ensure that the CPV operates at optimum operating temperature with minimum variation of temperature. Metal foam is a new class of material that possesses huge potential for thermal management. In this study, a functionally graded metal foam is proposed for the CPV thermal management system. Computational thermal fluid dynamic analysis is conducted to investigate the effect of porosity and pore density on the flow field and thermal performance of the aluminum foam heat sink. The investigation results revealed that 10 PPI functionally graded aluminum foam heat sink with two stages of porosity gradient 0.794 and 0.682 produced the lowest pressure drop and highest thermal performance. Temperature difference of 3.9°C was achieved for a solar cell with total heat generation of 900 W under water mass flow rate of 20 gs−1. [ABSTRACT FROM AUTHOR]

Air pollution is a widely discussed topic amongst the academic and industrial spheres as it can bring adverse effects to human health and economic loss. As humans spend most of their time at the office and at home, good indoor air quality with enriched oxygen concentration is particularly important. In this study, polysulfone (PSF) hollow fiber membranes fabricated by dry-jet wet phase inversion method were coated by a layer of polydimethylsiloxane (PDMS) or poly(ether block amide) (PEBAX) at different concentrations and used to evaluate their performance in gas separation for oxygen enrichment. The surface-coated membranes were characterized using SEM and EDX to determine the coating layer thickness and surface chemical properties, respectively. Results from the gas permeation study revealed that the PSF membrane coated with PDMS offered higher permeance and selectivity compared to the membrane coated with PEBAX. The best performing PDMS-coated membrane demonstrated oxygen and nitrogen gas permeance of 18.31 and 4.01 GPU, respectively with oxygen/nitrogen selectivity of 4.56. Meanwhile, the PEBAX-coated membrane only showed 12.23 and 3.11 GPU for oxygen and nitrogen gas, respectively with a selectivity of 3.94. It can be concluded the PDMS coating is more promising for PSF hollow fiber membrane compared to the PEBAX coating for the oxygen enrichment process. [ABSTRACT FROM AUTHOR]

Abstract: For the first time, thin‐film nanocomposite (TFN) nanofiltration membranes incorporated with graphene oxide (GO) were synthesized and used to separate phosphorus from water sources of varying properties. Prior to phosphorus removal tests, two different TFN membranes and one control thin‐film composite (TFC) membrane were subject to standard characterization in order to determine pure water flux, salt rejection, surface hydrophilicity, pore size, and porosity. By incorporation of GO, the water flux of composite membranes could be significantly improved with minimum decrease in salt rejection, mainly due to improved surface hydrophilicity coupled with enlarged pore size and overall structural porosity. Especially the TFN‐1 membrane was found to perform better owing to its good combination of water flux and solute rejection, higher water flux, and comparable phosphorus rejection in comparison to the TFC membrane. [ABSTRACT FROM AUTHOR]